displaying 1000 best results Help
Search results for: unconventional bearings
-
Supply current signal and artificial neural networks in the induction motor bearings diagnostics
PublicationThis paper contains research results of the diagnostics of induction motor bearings based on measurement of the supply current with usage of artificial neural networks. Bearing failure amount is greater than 40% of all engine failures, which makes their damage-free operation crucial. Tests were performed on motors with intentionally made bearings defects. Chapter 2 introduces the concept of artificial neural networks. It presents...
-
Should we seek further improvement of fluid film bearings - what for and how?
PublicationFluid film bearings have been extensively used in the industry because of their unbeatable durability and extremely low friction coefficient. Large bearings supporting shafts of huge and important rotating machines constitute a special group of fluid film bearings since the reliability of crucial systems, like for example electro-energetic system, rely on their trouble-free operation. Large thrust bearings, apart from enormous...
-
Current based Normalized Triple Covariance as a bearings diagnostic feature in induction motor
PublicationDiagnosis of induction motors, conducted remotely by measuring and analyzing the supply current is attractive with the lack of access to the engine. So far there is no solution, based on analysis of current, the credibility of which allow use in industry. Statistics of IM bearing failures of induction motors indicate, that they constitute more than 40% of IM damage, therefore bearing diagnosis is so important. The article provides...
-
Fatigue resistance investigation of the mb46 plain bearings under conditions of dynamic loadings
PublicationOdporność materiału łożyskowego MB46 na pęknięcia zmęczeniowe badano na stanowisku SMOK, w którym generowane jest zmienne jednokierunkowe obciążenie badanego łożyska. Materiał łożyskowy MB46 składa sie z warstwy brązu CuPb22Sn 3 spiekanego na taśmie stalowej, stanowiącej podłoże. Na warstwę brązu nałożona jest galwanicznie cienka warstwa stopu SnCu6 stanowiąca powłokę. Każde z badanych łożysk poddawane było 20-godzinnemu testowi...
-
Environmentally friedly propeller shaft support with the use of water lubricated foil bearings
PublicationW pracy przedstawiono podsumowanie prowadzonych badań w celu opracowania oryginalnej metodyki projektowania oraz technologii wykonania pierwszego w świecie łożyska foliowego smarowanego wodą. Zaprezentowano koncepcje nowego łożyska foliowego poprzecznego oraz opisano opracowany algorytm obliczeniowy wykorzystany do predykcji jego charakterystyk. W rezultacie prowadzonych prac opracowano i przebadano doświadczalnie na stanowisku...
-
Concept for interpretation and assessment of slide bearings operation in Diesel enfines in probabilistic approach
PublicationW artykule zaproponowano interpretację wartościującą działania, które (podobnie jak przedstawione w mechanice klasycznej działania Hamiltona i Maupertiusa oraz działanie wynikające ze zmiany pędu ciała) jest rozpatrywane jako wielkość fizyczna o jednostce miary zwanej''dżulosekundą''. Przedstawiono propozycję ilościowej interpretacji działania dowolnego poprzecznego łożyska ślizgowego, w którym zachodzą oddziaływania energetyczne...
-
Diagnostic model of compression-ignition engine slide bearings for controlling the changes of their state
PublicationW artykule przedstawiono koncepcję umożliwiającą sterowanie procesami zmian stanów eksploatacyjnych silnika na podstawie modelu diagnostycznego łożysk ślizgowych. Jako model łożyska ślizgowego przyjęty został topologiczny model diagnostyczny, pozwalający na pełne i dokładne wykorzystanie oleju smarowego jako jednego z nośników informacji o stanie technicznym łożyska. Przedstawiona została przykładowa interpretacja stanów eksploatacyjnych...
-
Klocki samopompujące w łożyskach hydrodynamicznych = Self-pumping pads in the hydrodynamic bearings
PublicationWe współpracy z firmą ALSTOM HYDRO (Szwajcaria), zespół Katedry Konstrukcji i Eksploatacji Maszyn Politechniki Gdańskiej przeprowadził symulacje przepływowe kilku rozwiązań konstrukcyjnych mających na celu zwiększenie niezawodności turbin wodnych. W artykule opisano jedno z takich rozwiązań - tak zwane łożysko z klockami samopompującymi. Głównym celem jest uzyskanie przepływu oleju w układzie smarowania łożyska hydrodynamicznego...
-
Experimental Study on Effectiveness of a Prototype Seismic Isolation System Made of Polymeric Bearings
PublicationSeismic isolation is identified as one of the most popular and effective methods of protecting structures under strong dynamic excitations. Base isolators, such as Lead Rubber Bearings, High Damping Rubber Bearings, and Friction Pendulum Bearings, are widely used in practice in many earthquake-prone regions of the world to mitigate structural vibrations, and therefore minimize loss of life and property damage during seismic events....
-
Induction motor bearings diagnostic indicators based on MCSA and normalized triple covariance
PublicationInduction motors are one of the most widely used electrical machines. Statistics of bearing failures of induction motors indicate, that they constitute more than 40% of induction motor damage. Therefore, bearing diagnosis is so important for trouble-free work of induction motors. The most common methods of bearing diagnosis are based on vibration signal analysis. The main disadvantage of those methods is the need for physical access...
-
Advanced Hysteretic Model of a Prototype Seismic Isolation System Made of Polymeric Bearings
PublicationThe present paper reports the results of acomprehensive study designed to verify the effectiveness of an advanced mathematical model in simulating the complex mechanical behaviour of a prototype seismic isolation system made of polymeric bearings (PBs). Firstly, in order to construct the seismic bearings considered in this research, a specially prepared flexible polymeric material with increased damping properties was employed....
-
Some fundamental aspects of self-levitating sliding contact bearings and their practical implementations
PublicationIn this study, fundamental aspects and mechanisms of acoustic levitation together with governing equations are presented first. Then, the acoustic levitation phenomenon is considered as a new way to design air suspension systems capable of self-levitation. A particular emphasis is laid on journal bearings and their specific geometrical configuration. A practical feasibility of using acoustic levitation to separate contacting surfaces...
-
Study of the Influence of Heat Convection Coefficient on Predicted Performance of a Large Tilting-Pad Thrust Bearing
PublicationPart of the heat generated by the shearing of the lubricating film during operation of a hydrodynamic bearing is transferred to the bearing components. In the case of the pad, which is usually fully submerged in the lubricating oil, heat is further transferred at the pad free walls to the oil by convection. This mechanism causes a thermal gradient in a pad and, consequently, its thermal deflection. In large hydrodynamic thrust...
-
Instantaneous power signal measurements for bearing diagnostics
Open Research DataBearing diagnostics can be carried out based on the method, which relies on the measurement and analysis of the variability of the signal instantaneous power, defined as the product of instantaneous current and voltage power supplied to the engines. Bearing damage causes the appearance of deformations, which are in the form of additional harmonic components...
-
Experimental research on water lubricated three layer sliding bearing with lubrication grooves in the upper part of the bush and its comparison with a rubber bearing
Publicationcomposite. Eachofitslayershasanimportantfunction.Speciallypreparedslidingsurfaceensures minimum resistance.Followingrunning-initssmoothnessbecomesveryhighandthebearingmay continue workingunder fluid lubricationregime.NBRlayerensuresbearingelasticity,goodvibration damping propertiesandinsusceptibilitytoshaftaxismisalignment.Theexternalbrasslayermakes fitting thebearingeasier. Experiment resultsoftheconductedresearchwerecomparedwiththoseforarubberbearingof similar...
-
Displacement piles - classification and methods for the calculation of bearing capacity.
PublicationDisplacement piles belong to a group of technologies whose main idea is to install or make a pile without extracting ground material. According to definition, contained in PN-EN:1997-1:2008, displacement piles should be considered as driven, pressed in using vibrators and made with the use of spread augers. The classification of piles used so far with regard to the technology of execution is modified. An additional element is the...
-
Mechanism of the fatigue cracks development in bearing slide layer
PublicationNa podstawie literatury przedstawiono wybrane problemy dotyczące powiązania wytrzymałości zmęczeniowej łożysk ślizgowych ze strukturą i charakterystyką materiału tworzącego warstwę ślizgową panwi.W szczególności analizowano mechanizm inicjacji i propagacji pęknięć zmęczeniowych jako zależną nie tylko od wzorca obciążenia dynamicznego, lecz również od geometrii i struktury warstwy ślizgowej.Wyróżniono dwa typy pęknięć: strukturalne...
-
Bearing errors passive sonar stationary target location
PublicationPrzedstawiono metodę wyznaczania współrzędnych nieruchomego celu na podstawie namiarów wykonywanych w sonarze pasywnym. Określono wymagania odnośnie ruchu sonaru, przy których błędy wyznaczania współrzędnych są minimalne. Podano zależności umożliwiające analityczne wyznaczanie błędów współrzędnych. Poprawność wyników analizy potwierdzono eksperymentami numerycznymi.
-
Influence of Collar Deformations on Hydrodynamic Thrust Bearing Performance
Publication -
Stability and load bearing capacity of a truss with elastic braces
PublicationThe present paper is devoted to the numerical and experimental investigations of stability of a truss stiffened by elastic braces. The model of a real roof truss scaled by factor ¼ was investigated. In the research the linear buckling and non-linear static analysis of the truss shell and beam model with geometric and material non-linearity is presented. The initial imperfections were assumed in the form of the first buckling mode....
-
Bioactive core material for porous load-bearing implants
PublicationSo far state of knowledge on biodegradable materials is reviewed. Among a variety of investigated materials, those composed of polymers and ceramics may be considered as only candidates for a core material in porous titanium alloy. The collagen and chitosan among natural polymers, polyhydroxy acids among synthetic polymers, and hydroxyapatite and tricalcium phosphate among ceramics are proposed for further research. Three essential...
-
Motor bearing diagnostics performed by means of laser vibrometer
PublicationDamage of bearings is the most common cause of failures in squirrel-cage induction motors. That is why the issues connected with diagnostics of bearings are so important. The equipment employed for bearing diagnostics usually makes use of vibrations as the criterion for technical condition of the bearings. This paper presents exemplary results of the research conducted on bearings with artificially introduced damage. A scanning...
-
Testing of fatigue strength limit of slide bearing materials
PublicationPrzedstawiono wyniki badań wytrzymałości zmęczeniowej wybranych trójwarstwowych łożysk cienkościennych. Zaprezentowano zdjęcia typowych pęknięć zmęczeniowych warstwy stopu łożyskowego. Obliczono i oceniono krytyczne wartości naprężeń stycznych warstwy ślizgowej.
-
Bearing capacity factors of sand assessed by model tests
PublicationPrzedstawiono wyniki własnych badań modelowych fundamentów bezpośrednich posadowionych na trzech rodzajach piasków, wykonane w warunkach płaskiego stanu odkształcenia. Przeanalizowano wpływ tarcia gruntu o ściany boczne stanowiska badawczego, wpływ efektu skali oraz powtarzalności wyników na nośność badanych fundamentów bezpośrednich. Zastosowano specjalną własną metodykę wykonywania badań modelowych eliminującą wymieniony wpływ...
-
Hydrodynamic journal bearing - ''Y'' particularly for steam turbines.
PublicationW artykule przedstawiono koncepcję i zasadę działania nowego, ślizgoweo łożyska poprzecznego typu ''Y''. Przedstawiono wady i zalety nowego rozwiązania. Porównano charakterystyki dynamiczne i statyczne klasycznego łożyska cytrynowego (soczewkowego) z nowym łożyskiem ''Y''.Podano przykładowe wdrożenia i ich efekty.
-
Non-linear model of high damping rubber bearing.
PublicationCelem artykułu jest analiza modelu łożyska wykonanego z wysokotłumiącej gumy, które wykorzystywane są do posadowienia konstrukcji budowlanych na terenach sejsmicznych. Model umożliwia numeryczną symulację pracy urządzenia pod zadanym obciążeniem i w danych warunkach termiczno-wilgotnościowych. Wyniki analizy pokazują, iż proponowany model umożliwia symulację zachowania się łożyska w szerokim zakresie odkształceń.
-
Effect of preconsolidation on pile bearing capacity in model tests
PublicationBadanie wpływu prekonsolidacji gruntu w badaniach modelowych w komorze kalibracyjnej. Zagęszczone piaski kwarcowe poddano prekonsolidacji przy OCR nie większym od 7. Analiza współczynnika parcia spoczynkowego gruntu. Wpływ wskaźnika prekonsolidacji na nośność podstawy i pobocznicy pali oraz zmiany naprężeń wokół modelu i odkształcenia objętościowe masywu gruntowego.
-
A stochastic approach to the problem of bearing capacity by the method of characteristics
PublicationW pracy omówiono zagadnienie nośności granicznej podłoża o własnościach losowych, przy obciążeniu od spoczywającego na nim fundamentu. Zaproponowano stochastyczną modyfikację metody charakterystyk bazującej na metodzie różnic skończonych. Analizowano zagadnienia związane z dyskretyzacją losowego ośrodka gruntowego, symulacją pola losowego oraz ze zbieżnością i stabilnością rozwiązania. Przedstawione podejście umożliwiło uwzględnienie...
-
Estimation of pile bearing capacity by dynamic and static tests
PublicationBadania dynamiczne, szczególnie dla pali wbijanych, w budownictwie hydrotechnicznym stają się coraz bardziej popularne. Badania, poparte formalnie zapisami zawartymi w Eurokodzie 7, wykorzystywane w badaniach ''na wodzie'' i ''na lądzie'' są szybkie i ekonomiczne. Przedstawiono serię badań dla gruntów uwarstwionych dla pali prefabrykowanych żelbetowych, wbijanych stalowych pali rurowych oraz pali Vibro-Fundex. Badania dynamiczne...
-
Modeling lubricant flow between thrust-bearing pads
PublicationInlet temperature is one of the main inputs in all models for the analysis of fluid film bearing performance. At the same time, inlettemperature distribution and also oil velocity distribution at the inlet are the result of flow phenomena in the gap between the bearingpads. These phenomena are complex and in many cases further affected by any special arrangements of forced oil supply to the gapbetween pads. The reason for such...
-
Experimental tests of water lubricated marine rubber bearing
PublicationW referacie przedstawiono stosowane obecnie rodzaje łożysk gumowych smarowanych wodą. Omówiono ich zalety i wady.W drugiej części pracy przedstawiono wyniki badań eksperymantalnych typowego okrętowego łożyska gumowego. Uzyskane rezultaty porównano z wynikami badań łożysk z polimerową panwią.
-
Some problems of slide bearing material fatigue evaluation.
PublicationA slide bearing alloy resistance against fatigue failures have been investigated for three different lubricants, different heat loadings and different stress ratio κ values. The research methods and data handling procedures for determination of particular parameter effects on fatigue strength have been described and analysed for experiments that were set and performed in laboratory tester SKMR-2. Main and interaction effects of...
-
Prospects of Decreasing Power Losses in a Hydrostatic Thrust Bearing
PublicationIn numerous machines, axial load is carried by tilting pad thrust bearings known since the beginning of 20th century. These bearings are commonly bath lubricated, which is simple, does not require any additional pumps, and, due to this, such systems are highly reliable. In a contemporary technology, however, minimization of friction losses became an important goal of machinery improvement. Calculations based on elementary rules...
-
Search for the most useful geometry of an acoustic journal bearing
PublicationComputer simulations of a number of journal bearing’s geometries utilising acoustic levitation were carried out. The choice of the best geometry depended on the ability of a deformed shape, created by piezo-electric elements, to facilitate squeeze film ultrasonic levitation, and also to create three evenly distributed diverging aerodynamic gaps. Deformations of analysed variants of the bearing’s shape were generated by numerical...
-
Large hydrodynamic thrust bearing: Comparison of the calculations and measurements
PublicationHydrodynamic thrust bearings, used to carry axial loads in heavily loaded shafts of water power plants hydro turbines, can reach outer diameters even exceeding 5 m. In such large objects scale effect could be observed. According to this, allowable bearing specific load assuring safe operation of the bearings has to be decreased, which increases thrust bearing dimensions. This effect is caused by excessive thermal deflections of...
-
Selected nutrients determining the quality of different cuts of organic and conventional pork
Publication -
Nutritional and Pharmaceutical Properties of Bioactive Compounds in Organic and Conventional Growing Kiwifruit
PublicationThe bioactivity of two kiwifruit’s cultivars growing under organic and conventional conditions were studied and compared. The bioactive compounds were extracted with water and ethanol using similar conditions which are applied in pharmaceutical applications and for daily fruit consumption such as tea drink. Antioxidant radical scavenging assays [ferric-reducing/antioxidant power (FRAP); cupric reducing antioxidant capacity (CUPRAC);...
-
Possibility of use adsorption chillers for increase efficiency in conventional power plant
Publication -
Comparative analysis of earthships and conventional buildings in terms of investment and operating costs
PublicationThe aim of the master's thesis is to present the idea of earthships and compare them with conventional buildings in terms of investment and operating costs. Earthships are buildings erected from tires and other wastes whose characteristic feature is their self-sufficiency. The first part of the master's thesis is to discuss the basic issues related to the earthship building. The beginnings of tire homes and their development are...
-
Effect of conventional cooking on changes in the contents of basic composition and glucosinolates in kale
PublicationBrassica vegetables have been strongly recommended as part of human diet because of its high content of bioactive sulphur compounds, eg glucosinolates. The nutrient and health promoting compounds in kale are significantly affected by traditional cooking. The study investigated changes in the levels of dry mass, ash, fat, total protein, dietary fibre as well as total and individual glucosinolates in the kale due to the traditional...
-
Polymeric Bearings as a new base isolation system suitable for mitigating machine-induced vibrations
PublicationThe present paper summarizes the preliminary results of the experimental shaking table investigation conducted in order to verify the effectiveness of a new base isolation system consisting of Polymeric Bearings in reducing strong horizontal machine-induced vibrations. Polymeric Bearing considered in the present study is a prototype base isolation system, which was constructed with the use of a specially prepared flexible polymer...
-
Application of acoustic emission for detection of fatigue microdemage in main and crank bearings for diesel engines
PublicationThe article presents reasons for applying the acoustic emission (AE) to detect fatigue microdamage in main bearings and crank bearings of ship main engines. Problem of determination of the fatigue life for slide bearing bushes was characterized in general. There were demonstrated properties of the objects of research, which were bushings made of the MB58 alloy, as well as an overall description of the research. It was shown that...
-
Influence of main design parameters of ship propeller shaft water-lubricated bearings on their properties
PublicationW artykule omówiono wpływ głównych parametrów konstrukcyjnych i eksploatacyjnych takich jak wielkość luzu łożyskowego, własności materiału panwi, stanu powierzchni skojarzenia ślizgowego oraz temperatury i zasolenia wody na nośność hydrodynamiczną łożyska okrętowego wału śrubowego smarowanego wodą.
-
Polymeric Bearings – A New Base Isolation System to Reduce Structural Damage during Earthquakes
PublicationBase isolators, like lead rubber bearings, high damping rubber bearings or friction pendulum systems are extensively used in practice in many seismically active regions to protect structures against earthquake forces. The present paper reports the results obtained from the experimental study aimed to determine the effectiveness of the Polymeric Bearings in suppressing structural vibrations during dynamic excitations and therefore...
-
Influence of surface roughness topography on properties of water lubricated polymer bearings, experimental research
PublicationW artykule przedstawiono wyniki badań eksperymentalnych, których celem było zidentyfikowanie wpływu ułożenia chropowatości na powierzchni ślizgowej łożyska smarowanego wodą z polimerową panwią. Badania wykazały, że wpływ ten jest mniejszy niż oczekiwano a na własności łożyska ma wpływ głównie wysokość chropowatości.
-
Influence of local bush wear on properties of water lubricated marine stern tube bearings
PublicationW artykule przedstawiono propozycję metody obliczania łożysk ślizgowych smarowanych cieczą o niskiej lepkości (wodą) w których doszło do lokalnego zużycia panwi. Proponowana metoda uwzględnia sprężystą deformację panwi (model EHL) oraz zmianę geometrii będącą wynikiem zużycia.
-
The dynamic performance analysis of the Micro-turbine's rotor supparted on slide and roling element bearings
PublicationThis article presents the results of investigations of dynamic characteristics of a small-dimension rotor with slide and rolling element bearings. The object of investigations was the rotor-bearing system designed for the ORC based low-power steam micro-turbine. The investigations were performed using MESWIR series programs, as well as commercial FEA software ABAQUS and MADYN 2000. The results of modal analysis of the micro-rotor...
-
Compensation of thermal deformations as a method of improving performance of large tiling pad thrust bearings.
PublicationTermiczne odkształcenia klocków łożyskowych wywierają niekorzystny wpływ na właściwości łozysk o dużych średnicach. W pracy przedstawiono przegląd znanych z techniki sposobów ograniczania odkształceń termicznych.Na podstawie wyników własnych badań szczegółowo omówiono efekty kompensacji odkształceń w dwóch przykładowych rozwiązaniach konstrukcyjnych: łożysku z klockami podpartymi na sprężynach śrubowych i z klockami podpartymi...
-
Structural properties of foil bearings: a closed-form solution validated with finite element analysis
PublicationFluid film thickness in a compliant foil bearing is greatly influenced by the deflection of the bearing structure. Therefore, in order to properly model performance of a foil bearing, it is mandatory that the deflection of the compliant bearing structure due to the generated hydrodynamic pressure is determined accurately. This article proposes an easy-to-use two-dimensional model, which takes into account detailed geometry of the...
-
Evaluation of occupational exposure in a slide bearings factory on the basis of urine and blood sample analyses
PublicationZbadano wpływ pracy w zakładach łożysk ślizgowych na zdrowie pracowników. Przeprowadzono analizę próbek moczu i krwi pobranych od 42 pracowników i 6 osób zatrudnionych w administracji przedsiębiorstwa, stanowiących grupę kontrolną. Oznaczono zawartość Al, Cu, Pb i Zn we krwi i moczu pracowników dwukrotnie, przed i po terapii za pomocą chelatowania, stosując ICP-MS oraz metodę dodatku wzorca. Istotność różnic w zawartości pierwiastków...
-
Novel condition monitoring of induction motor bearings via motor current signature analysis
PublicationThe paper authors are researching the assessment of bearing conditions in induction motors. The methods developed by the authors are based on measurements and analysis of the motor supply current, which is particularly attractive in the absence of access to the engine. The article provides an overview of selected methods of induction motor bearings diagnostic based on Motor Current Signature Analysis (MCSA). However, there is no...
-
The use of plate springs for preloading of a system of tapered roller bearings of a wind turbine gearbox
PublicationThe use of preloaded tapered roller bearings in wind turbine drive systems allows a transfer of load in the case of high variations of axial forces. The examined bearing system, a modification of a current design, consists of a pair of different sized bearings. Previous study showed the high sensitivity of tapered roller bearings on the existing radial interference. Dimensional tolerances used in the original design do not allow...
-
Water-lubricated bearings of ship propeller shafts - problems, experimental tests and theoretical investigations
PublicationW pracy przedstawiono problemy związane z projektowaniem, montażem i ekspolatcją smarowanych wodą łożysk okrętowych wałów głównych.Przedstawiono wyniki prowadzonych prac badawczych ekperymntalnych i obliczeń.
-
It applications for the remote testing of hearing.
PublicationTelemedycyna odgrywa coraz wiekszą rolę w diagnostyce i leczeniu osób z ubytkami słuchu. Jest to związane m.in. ze specyfiką badań audiometrycznych. Postęp technologiczny w dziedzinie aparatów słuchowych i implantów ślimakowych wymusza nowe metody diagnozy w audiologii, jak również w praktyce otolaryngologicznej. Serwis ''Telezdrowie'', w którym zaimplementowano liczne testy przesiewowe jest przykładem prowadzenia diagnostyki w...
-
Hypertension and cochlear hearing loss
Publication -
Multimedia Applications for the Hearing Impaired.
PublicationJednym z elementów przeciwdziałania szybko narastającym zagrożeniom niedosłuchem są aplikacje oprate na nowoczesnych technologiach. W wyniku współpracy Katedry Systemów Multimedialnych PG z warszawskim Instytutem Fizjologii i Patologii Słuchu opracowano wdrożone na szeroką skale multimedialne systemy przesiewowych badań zmysłów komunikowania się. Ponadto, nowsze opracowania dotyczą maskowania szumów usznych z wykorzystaniem linearyzacji...
-
Removal of metal particles from carbon nanotubes using conventional and microwave methods
Publication -
Challenging conventional views on mobile-telecommunications investment: evidence from conflict zones
Publication -
Catalytic Degradation of Safranin T in Aqueous Medium Using Non-conventional Processes
Publication -
Application of Organic Rankine Cycle as bottoming cycle to conventional heat and power plant
PublicationW pracy rozważono możliwość zastosowania układu ORC w skojarzeniu z ciepłownią lub elektrociepłownią celem podniesienia stopnia wykorzystania jednostki CHP podczas eksploatacji w skali roku. Połączenie układu ORC z zawodową jednostką CHP może wpłynąć na wzrost rocznej produkcji energii elektrycznej i jednoczsne zmniejszenie fluktuacji podczas pracy bloku energetycznego. Z jednej strony następuje konwersja energii cieplnej na elektryczną...
-
Organic and conventional kiwifruit myths versus reality: antioxidant, antiproliferative and health effects
PublicationComparison between organic and conventional kiwifruit cultivars ''Hayward'' and ''Bidan'', which was done by four redical scavenging assays, ESI-MS, and DSC measurements, showed significant differences between cultivars. Such results were not estimated in kiwifruit growing under organic and conventional conditions. The extraction of bioactive compounds was done by two different methods: sequential extraction with ethyl acetate...
-
Organic and conventional kiwifruit, myths versus reality: antioxidant, antiproliferative and helth effects
PublicationComparison between organic and conventional kiwifruit cultivars 'Hayward' and 'Bidan', which was done by four radical scavenging assays, ESI-MS, and DSC measurements, showed significant differences between the cultivars. Such results were not estimated in kiwifruit growing under organic and conventional conditions. The extraction of bioactive compounds was done by two different methods: sequential extraction with ethyl acetate...
-
Conventional and Alternative Sources of Thermal Energy in the Production of Cement—An Impact on CO2 Emission
Publication -
Direct modulation for conventional matrix converters using analytical signals and barycentric coordinates
PublicationThis paper proposes the generalized direct modulation for Conventional Matrix Converters (CMC) using the concept of analytical signals and barycentric coordinates. The paper proposes a novel approach to the Pulse Width Modulation (PWM) duty cycle computing, which allows faster prototyping of direct control algorithms. The explanation of the new idea using analytical considerations demonstrating the principles of direct voltage...
-
Comparison of the Effects of Conventional and Alternative External Carbon Sources for Enhancing of the Denitrification Process
PublicationFood industry effluents are considered a potential alternative for methanol when seeking external carbon sources to enhance denitrification in municipal wastewater treatment plants (WWTPs). The aim of this study was to determine the immediate effects of dosing different carbon sources on the denitrification capability of process biomass from the "Wschod" WWTP in Gdansk (northern Poland). Five carbon sources, including settled wastewater,...
-
Compliance tests of the polymer layers used as hydrodynamic bearing coatings
PublicationOperational experience and scientific investigations results showed that polymer lined hydrodynamic bearings can withstand more severe operating conditions compared than white metal bearings. PTFE and PEEK-based coatings are the most frequently used as Babbitt alternatives. Both polymers differ significantly from the each other in material properties. According to catalogue data compression modulus of PTFE, it is about an order...
-
Running performance of an aerodynamic journal bearing with squeeze film effect
PublicationResults of theoretical and experimental studies concerning the performance of an aerodynamic journal bearing of which running is assisted by squeeze film ultrasonic levitation (SFUL) are presented in this paper. The SFUL mechanism not only can separate journal from the bearing at the start and stop phases of operation but also can significantly contribute to the dynamic stability of the bearing when it runs at speed. Computer calculations...
-
Diagnosis of bearing damage in induction motors by instantaneous power analysis
PublicationResearch of the machine with simulated bearing damages has been carried out, where variable load torque, simulating bearing damage, was introduced. The results show that components which can be used for bearings diagnosis appear in the spectrum of the product of current and supply voltage instantaneous values. These components are easier to identify than the components of current spectrum, which have been used so far in diagnostic...
-
Photophysical properties and photochemistry of a sulfanyl porphyrazine bearing isophthaloxybutyl substituents
Publication -
Loading pattern effects on fatigue resistance of slide bearing lining
PublicationPrzedstawiono relacje pomiędzy przebiegami obciążeń dynamicznych a stanem naprężeń w warstwie nośnej łożysk ślizgowych. Porównano przebiegi naprężeń dla maszyny badawczej MWO (z wirującym wektorem obciążenia) do naprężeń charakterystycznych dla maszyny SMOK (z jednokierunkowym zmiennym wektorem obciążenia).
-
Viscoelastic lubrication on spherical slide bearing in impulsive unsteady motion.
PublicationNiniejsza praca przedstawia numeryczne i semi-analityczne wyznaczanie składowych wektora prędkości lepkosprężystego oleju, oraz wartości ciśnienia hydrodynamicznego i sił nośnych w sferycznym łożysku ślizgowym o zmieniającej się w czasie niesymetrycznej szczelinie smarnej podczas nieustalonego impulsywnego smarowania. Łożyska ślizgowe o czopach kulistych występują w maszynach transportowych w celu lepszego manewrowania ustawieniem...
-
Nonlinear rate dependent model of high damping rubber bearing.
PublicationCelem artykułu jest analiza nieliniowego modelu łożyska wykonanego z wysokotłumiącej gumy, który symuluje pracę urządzenia pod zadanym obciążeniem. Parametry modelu dobrane są na podstawie wyników badań eksperymentalnych. Wyniki pracy pokazują, iż analizowany model umożliwia symulację zachowania się łożyska w szerokim zakresie odkształceń
-
Application of neural networks for description of pressure distribution in slide bearing.
PublicationBadano rozkład ciśnienia hydrodynamicznego w łożysku ślizgowym dla wybranych wariantów łożyska. Wykazano, że zastosowanie sieci neuronowych umożliwia opis rozkładu ciśnienia hydrodynamicznego z uwzględnieniem zmian geometrycznych (bezwymiarowa długość - L) i mechanicznych (mimośrodowość względem H) łożyska.
-
Identification of slide bearing main parameters using neural networks.
PublicationWykazano, że sieci neuronowe jak najbardziej nadają się do identyfikacji głównych parametrów geometrycznych i ruchowych hydrodynamicznych łożysk ślizgowych.
-
Impact of Spatial Noise Correlation on Bearing Accuracy in DIFAR Systems
PublicationDIFAR type underwater passive systems are one of the more commonly used tools for detecting submarines. At the design stage, which usually uses computer simulations, it is necessary to generate acoustic noise of the sea. It has been shown that correlating noise significantly reduces these errors compared to the assumption that noise is uncorrelated. In addition, bearing errors have been shown to be the same in systems with a commonly...
-
Equalization of pad loads in large tilting pad thtust bearing
PublicationW pracy przedstawiono przebieg projektowania zmodernizowanego łożyska wzdłużnego hydrogeneratora. Na podstawie eksploatacyjnych danych o zróżnicowaniu temperatury klocków łożyskowych, na drodze obliczeń elasto-termo-hydrodynamicznych, stwierdzono konieczność wyrównania rozkładu obciążenia na poszczególne klocki łożyska. Cel został osiągnięty poprzez wprowadzenie podatnego podparcia segmentów łożyska na sprężynach płytowych, których...
-
Chapter 2: Modelling and analysis of rotor with magnetic bearing system
PublicationThe paper is concerned with rotor magnetic bearing system modelling. Such system is a relatively complex electromechanical system and can be considered as typical mechatronic one. The port-based modelling of physical systems has been used to obtain discrete-continuous model of considered system. Proposed approach enables to obtain reduced low-order lumped parameter representation of the system including gyroscopic interactions....
-
The improvement of axial bearing capacity of open-end pipe piles
PublicationZaproponowano sposób zwiększania nośności osiowej pali rurowych z otwartym dnem za pomocą wewnętrznych pierścieni. Przedstawiono wyniki badań w skali naturalnej i badań modelowych. Przeprowadzono analizę teoretyczną zjawiska metodą analityczną i numeryczną. Badania i analizy potwierdziły skuteczność proponowanego rozwiązania technicznego.
-
Stochastic contributions on the pressure in slide bearing gaps after impulse
PublicationTematem niniejszej pracy są parametry smarowania poprzecznych i poprzeczno-wzdłużnych łożysk ślizgowych olejem o własnościach lepkosprężystych. Wyprowadzono zmodyfikowane równania Reynoldsa do wyznaczania ciśnienia hydrodynamicznego ślizgowych łożysk o powierzchniach cylindrycznych, sferycznych, stożkowych i parabolicznych, przy jednoczesnym uwzględnieniu możliwości brania pod uwagę zmiennej lepkości oleju po grubości warstwy smarującej....
-
Influence of an applied bearing system on behaviour of multi-span footbridge
PublicationThe cycle overpass in Gdynia is a box structure over 300 metres long, 10-span. It was opened for bicycle traffic in the second half of 2013. At the end of its construction, there was failure due to excessive horizontal displacement of the system. A number of bearings exceeded the range of permissible transverse shifts thus it was necessary to temporarily protect the spans from slipping. The FEM analysis of the original solution...
-
Experimental research on marine oil-lubricated stern tube bearing
PublicationBearings of propeller shafts are very crucial elements of the propulsion system of each of the ships. The safety of shipping depends on their durability and reliability. The new legal restrictions mean that today we are looking for environmentally friendly solutions. That is why water-lubricated bearings are becoming more and more popular. So, will oil-lubricated shaft bearings belong to the past? The bearing with a white metal...
-
Cascading transitions toward unconventional charge density wave states in the quasi-two-dimensional monophosphate tungsten bronze P4W16O56
PublicationSingle crystals of the m = 8 member of the low-dimensional monophosphate tungsten bronzes (PO2)4(WO3)2m family were grown by chemical vapour transport technique and the high crystalline quality obtained allowed a reinvestigation of the physical and structural properties. Resistivity measurements revealed three anomalies at TC1 = 258 K, TC2 = 245 K and TC3 = 140 K, never observed until now. Parallel X-ray diffraction investigations...
-
Assessment of the Effectiveness of a Short-term Hearing Aid Use in Patients with Different Degrees of Hearing Loss
PublicationThe study presents evaluating the effectiveness of the hearing aid fitting process in the short-term use (7 days). The evaluation method consists of a survey based on the APHAB (Abbreviated Profile of Hearing Aid Benefit) questionnaire. Additional criteria such as a degree of hearing loss, number of hours and days of hearing aid use as well as the user’s experience were also taken into consideration. The outcomes of the benefit...
-
Comparable analysis of PID controller settings in order to ensure reliable operation of active foil bearings
PublicationIn comparison to the traditional solutions, active bearings offer great operating flexibility, ensure better operating conditions over a wider range of rotational speeds and are safe to use. In order to ensure optimum bearing performance a bearing control system is used that adapts different geometries during device operation. The selection of optimal controller parameters requires the use of modern optimization methods that make...
-
Comparison of the characteristics of journal bearings determined according to ISO 7902:2020 and obtained by other methods
PublicationThe article presents selected characteristics of journal bearings calculated with the use of various methods and compared to the results obtained with application of the basic bearing characteristics calculation procedure, as described in the ISO 7902:2020 standard. Additionally, the presented calculation results were compared with the parameters measured during experimental tests of the sliding bearings, working under loads and...
-
The use of Acoustic Emission to identification damages bearings the main and crank engines about the automatic ignition
PublicationThe article describes the laboratory tests, which make the first stage of the study concerning the use of the AE method to determine the technical state of the slide bearings in engines with self-ignition. The aim of the present tests was to compare the recorded signals in relation to the technical state of the material of the bearing bush and to check the possibility of using the AE method in determining the transition moment...
-
Shaft Misalignment Influence on Water Lubricated Turbine Sliding Bearings with Various Bush Modules of Elasticity
PublicationW artykule przeanalizowano wpływ wielkości przenoszenia osi wału względem panwi na nośność łożyska. Analizie poddano łożyska z odmiennymi rodzajami panwi o różnej sztywności.
-
Marine propeller shaft bearings under low-speed conditions: water vs. oil lubrication
PublicationThe bearings used in shipbuilding, hydropower, and water pumps have undergone a metamorphosis in recent decades. Because of environmental regulations, lubrication with grease or mineral oil is prohibited. Thus, the standard solutions include water-lubricated bearings with polymer bushings or sealed systems lubricated with oil. When properly designed, assembled, and operated, bearings can operate reliably for years. However, specific...
-
WATER LUBRICATED MAIN SHAFT BEARINGS - MODERN SOLUTION FOR HYDROPOWER INDUSTRY - Experimental and theoretical studies
PublicationWater-lubricated bearings are finding increasingly wide use in various branches of industry. As such, they may also be encountered in hydro power industry. They are also increasingly frequently employed in bearing systems of marine shaft propulsions and water pumps [1]. This rising popularity is due to a number of reasons [2]. First of all, their simple construction has direct impact on the level of pricing which is usually quite...
-
Research on water lubricated main shaft bearings in conditions of improper lubrication and cooling conducted on high torque real-life scale bush test rig
PublicationWater lubricated polymer bushes find increasingly popular use in the sliding bearings of marine propellers, water turbines and pump shafts. Such popularity is partly due to their simple construction which also means relatively affordable price. In addition, properly designed and installed water lubricated bearings may well last for over a decade. However, in practical experience one may also observe cases of rapid wear...
-
Numeryczna analiza trójwymiarowego przepływu w polimerowym łożysku smarowanym wodą = Numerical analysis of three dimensional flow in water lubricated bearing with polymer bearing bush
PublicationW referacie przedstawiono wyniki obliczeń łożysk smarowanych wodą w oparciu o metodę CFD - obliczeniowej mechaniki płynów. Wykazano przydatność nowoczesnych narzędzi obliczeniowych do rozwiązywania podobnych problemów.
-
Contemporary Readings in Law and Social Justice
Journals -
Unconventional Models of Computation
Conferences -
Unconventional and user-friendly sampling techniques of semi-volatile organic compounds present in an indoor environment: An approach to human exposure assessment
PublicationThe commonly applied solutions used to assess the potential risk of human exposure to semi-volatile organic compounds (SVOCs) are based on the investigation of biological samples collected in an invasive or non-invasive manner. For SVOCs, which are typically introduced to humans through the respiratory system, dermal adsorption, or digestive system, sampling solutions generally used in the indoor environments are classified as...
-
ANALYSIS OF THE LOAD-CARRYING CAPACITY OF A HYDRODYNAMIC WATER-LUBRICATED BEARING IN A HYDROELECTRIC POwER PLANT
PublicationThe paper presents an analysis of the load-carrying capacity of a historic hydrodynamic water-lubricated radial bearing of an unconventional segment design installed in the Braniewo Hydroelectric Power Plant. The aim of the calculations was to determine whether the bearing operates in the conditions of hydrodynamic or mixed lubrication, as well as to establish the optimal geometry of the axial grooves allowing for the highest load-carrying...
-
Quasistatic and fatigue behavior of an AISI H13 steel obtained by additive manufacturing and conventional method
PublicationThis work aims to compare the mechanical behavior of an AISI H13 steel obtained by additive manufacturing with that obtained by conventional manufacturing methods. The average values of the ultimate tensile strength (UTS) and ductility obtained for the specimens produced by the conventional method were equal to 658 MPa and 18%, respectively, which compares with 503 MPa and 0.75% registered for the selective laser melting (SLM)...
-
Three-Dimensional Fractography for Conventional and Additive Manufactured Steels After Bending-Torsion Fatigue
PublicationIn this study, fracture surface topography parameters were measured to investigate the effects of multiaxial loading. In order to assess the metrological aspects of fracture for notched specimens made of high-strength steels processed by both conventional and additively manufacturing (AM) techniques, an optical surface profilometer was used. Three bending moment to torsion moment ratios (B/T) were studied, i.e. 2, 1 and 2/3. The...
-
By-Products from Food Industry as a Promising Alternative for the Conventional Fillers for Wood–Polymer Composites
PublicationThe present paper describes the application of two types of food-industry by-products, brewers’ spent grain (BSG), and coffee silverskin (ŁK) as promising alternatives for the conventional beech wood flour (WF) for wood–polymer composites. The main goal was to investigate the impact of partial and complete WF substitution by BSG and ŁK on the processing, structure, physicochemical, mechanical, and thermal properties of resulting...
-
Non-conventional approach in single-sided lapping process: kinematic analysis and parameters optimization
PublicationThe lapping process is strongly affected by a number of input parameters. One of the fundamental mechanical processes in lapping is the abrasive effect of particles. In order to examine the influence of the kinematic parameters on the lapping uniformity of unconventional single-sided machine, numerical simulations of particles sliding trajectories are performed. Changing the kinematic parameters, e.g., rotational velocities or...
-
Modelling AOB-NOB competition in shortcut nitrification compared with conventional nitrification-denitrification process
PublicationIn particular, mainstream deammonification and/or shortened nitrificationdenitrification via nitrite (so-called “nitrite shunt”) is a promising new treatment concept that has the potential to revolutionise how nitrogen removal is achieved at WWTPs. Understanding the role of the AOB/NOB competition in the nitrogen cycle in wastewater treatment systems will change operational strategies of the novel nitrogen removal processes. The...