Filtry
wszystkich: 1688
wybranych: 1503
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: TYPES
-
Anomalous decay of quantum correlations of quantum-dot qubits
PublikacjaWe study the evolution of quantum correlations, quantified by the geometric discord, of two excitonic quantum-dot qubits under the influence of the phonon environment. We show that the decay of these correlations differs substantially from the decay of entanglement. Instead of displaying sudden-death-type behavior, the geometric discord shows a tendency to undergo transitions between different types of decay, is sensitive to nonlocal...
-
New trends in development of micro heat exchangers for ORC's
PublikacjaIn the paper, new trends in development of micro heat exchangers for CHP are presented. Main attention is concentrated on the question, how channels size and thermal development lenght affect the heat transfer. New types of micro heat exchangers developed at the Institute of Fluid-Flow Machinery PAS and the methoda of their design are presented. The new experimental testing methods of the micro-channel heat exchangers, new algorithms...
-
Maritime heritage of small port towns of the Polish coast
PublikacjaThe article describes problems of the gradual disappearance of real maritime heritage in small Polish port cities. The maritime heritage of small port cities was shaped by coastal processes and urban historical conditions what has led to creation of specific types of landscapes. Special architectural objects of the post-port heritage of small ports of the Polish coast are hydrotechnical constructions (i.e. breakwaters, quays),...
-
Fluctuation-enhanced scent sensing using a single gas sensor
PublikacjaScent or aroma sensing during aromatherapy can be carried out by applying only a single resistance gas sensor (TGS - Taguchi Gas Sensors). This paper considers the efficiency of detection of essential oils by DC resistance and its fluctuations observed in TGS sensors. A detailed study has been conducted for scents emitted by five popular essential oils using three sensor types (TGS 2600, TGS 2602, TGS 823). The research was focused...
-
Spectral Methods for Modelling of Wave Propagation in Structures in Terms of Damage Detection—A Review
PublikacjaModern methods of detection and identification of structural damage direct the activities of scientific groups towards the improvement of diagnostic methods using for example the phenomenon of mechanical wave propagation. Damage detection methods that use mechanical wave propagation in structural components are extremely effective. Many different numerical approaches are used to model this phenomenon, but, due to their universal...
-
A Device for Measuring Auditory Brainstem Responses to Audio
PublikacjaStandard ABR devices use clicks and tone bursts to assess subjects’ hearing in an objective way. A new device was developed that extends the functionality of a standard ABR audiometer by collecting and analyzing auditory brainstem responses (ABR). The developed accessory allows for the use of complex sounds (e.g., speech or music excerpts) as stimuli. Therefore, it is possible to find out how efficiently different types of sounds...
-
A Biofeedback System that Uses the Game to Study Electrical Muscle Activity
PublikacjaThe aim of this project was to design a system that will allow performing repetitive muscle exercises using a biofeedback device. It is supposed to enhance the motivation and attractiveness of the performed tasks thanks to an interactive game developed for mobile devices with the Android operating system. The built-in calibration mechanisms enable the users to play a game that is independent of their abilities which evens out the...
-
Wave transmission across surface interfaces in lattice structures
PublikacjaWithin the lattice dynamics formulation, we present an exact solution for anti-plane surface waves in a square lattice strip with a surface row of material particles of two types separated by a linear interface. The considered problem is a discrete analog of an elastic half-space with surface stresses modelled through the simplified Gurtin–Murdoch model, where we have an interfacial line separating areas with different surface...
-
Services Marketing Influence On Marketing Theory Evolution,
PublikacjaThe discovery of differences between tangible goods and services in the 1970s was one of the most landmark moments in the history of marketing with an emphasis being shifted to the need for using different/diversified marketing activities while dealing with various industries and types of products. The objective of this article is to briefly characterise the evolution of the marketing thought and to present the crucial influence...
-
Scheduling of identical jobs with bipartite incompatibility graphs on uniform machines. Computational experiments
PublikacjaWe consider the problem of scheduling unit-length jobs on three or four uniform parallel machines to minimize the schedule length or total completion time. We assume that the jobs are subject to some types of mutual exclusion constraints, modeled by a bipartite graph of a bounded degree. The edges of the graph correspond to the pairs of jobs that cannot be processed on the same machine. Although the problem is generally NP-hard,...
-
T1 RELAXATION TIME CALLIBRATION IN MAGNETIC RESONANCE IMAGING USING NANODIAMOND PHANTOMS
PublikacjaMRI is increasingly used in radiation treatment planning because of the excellent soft tissue contrast in the obtained images. It allows more precise definition of the boundaries between healthy tissues and those affected by cancerous lesions. To obtain good image quality, the difference in signal between two types of tissue must be significant despite the noise so it must be properly calibrated. This calibration includes...
-
High-accuracy computation of hard X-ray focusing and imaging for refractive optics
PublikacjaA mathematical apparatus for solving problems of X-ray wave propagation through complex optical systems, when the lens thickness can change with jumps, is developed and presented. The developed method is based on the use of the superposition of oriented Gaussian beams, which satisfy the Helmholtz equation with high accuracy. The wave propagation in air and through kinoform and ordinary lenses is considered. Focusing and imaging...
-
Tworzenie modelu pojęciowego dla zarządzania ryzykiem na przykładzie procesu laminowania w stoczni jachtowej
PublikacjaCelem artykułu jest zaproponowanie modelu pojęciowego normalizującego kryteria oceny ryzyka w systemie zarządzania jakością w stoczni jachtowej. Zamiarem jest przeprowadzenie analizy danych, pozwalającej wytyczyć zbiory o wysokim, średnim i niskim poziomie istotności dla wszystkich błędów powstających w procesie laminowania. W artykule skoncentrowano się na najważniejszych pojęciach związanych z ryzykiem i kryteriami jego oceny....
-
BADANIE EFEKTYWNOŚCI WYKRYWANIA ANOMALII PROCESOWYCH W DZIAŁANIU TURBINY PAROWEJ ELEKTROWNI JĄDROWEJ PRZY POMOCY METOD WIELOWYMIAROWEJ ANALIZY STATYSTYCZNEJ
PublikacjaW artykule przedstawiono analizę możliwości wykrywania anomalii procesowych w działaniu turbiny parowej elektrowni jądrowej przy pomocy metod wielowymiarowej analizy statystycznej. Zasymulowano symptomy dwóch rodzajów uszkodzeń turbiny parowej tj. uderzenie wodne oraz, wyciek pary z zaworu części niskoprężnej. Jako narzędzie diagnostyczne wykorzystano Metodę Składników Podstawowych PCA (z ang. Principal Component Analysis). Jako...
-
Przegląd rodzajów chiralnych faz stacjonarnych oraz możliwości ich zastosowań w chromatografii cieczowej
PublikacjaChromatograficzne rozdzielanie związków optycznie czynnych ma ogromne znaczenie nie tylko w przemyśle farmaceutycznym, ale i agrochemicznym, a także w badaniach naukowych różnego rodzaju. W niniejszym opracowaniu scharakteryzowano komercyjnie dostępne chiralne fazy stacjonarne na bazie, cyklodekstryn, polisacharydów, makrocyklicznych antybiotyków, eterów koronowych, a także fazy proteinowe, ligandowymienne, jonowymienne oraz fazy...
-
Reject water and landfil leachate treatment with hydrophyte method - preliminary results
PublikacjaTreatment of landfill leachate (LL) and reject water (RWC) from dewatering of digested sludge in WWTPs have become one of the actual problems. Treatment of both types of wastewater is in many cases very costly and difficult due to quality and quantity fluctuations in time as well as high concentrations of specific pollutants. In case of our investigation the TSS concentration in RWC was two times higher than in LL. The shere of...
-
Application of vertical flow cw for highly contaminated wastewater treatment
PublikacjaBasing on quantitative and qualitative characteristics of reject waters generated during digested sewage sludge dewatering on centrifuges in conventional WWTP (RWC) and municipal landfill leachate (LL), the pilot constructed wetlands for treatment of both types of highly contaminated wastewater were designed. In the paper the characteristics of the pilot plants and assumed treatment efficiencies are presented. According to the...
-
Approaches Towards Better Immunosuppressive Agents
PublikacjaSeveral classes of compounds are applied in clinics due to their immunosuppressive properties in transplantology and the treatment of autoimmune diseases. Derivatives of mycophe-nolic acid, corticosteroids and chemotherapeutics bearing heterocyclic moieties like methotrexate, azathioprine, mizoribine, and ruxolitinib are active substances with investigated mechanisms of action. However, improved synthetic approaches of known drugs...
-
Automated anonymization of sensitive data on production unit
PublikacjaThe article presents an approach to data anonymization with the use of generally available tools. The focus is put on the practical aspects of using open-source tools in conjunction with programming libraries provided by suppliers of industrial control systems. This universal approach shows the possibilities of using various operating systems as a platform for process data anonymization. An additional advantage of the described...
-
Comparison of selected electroencephalographic signal classification methods
PublikacjaA variety of methods exists for electroencephalographic (EEG) signals classification. In this paper, we briefly review selected methods developed for such a purpose. First, a short description of the EEG signal characteristics is shown. Then, a comparison between the selected EEG signal classification methods, based on the overview of research studies on this topic, is presented. Examples of methods included in the study are: Artificial...
-
The guidelines and principles for planning and design of road restraint systems
PublikacjaThe project RID 3A Road Safety Equipment (RoSE) implemented by the Gdansk University of Technology within the RID programme, aims to conduct a comprehensive study and analyses of different vehicle containment systems (PN-EN 1317) and types of support structures (PN-EN 12767) and their performance. Within the project an analysis will be conducted of available research reports...
-
IZOLACJA I IDENTYFIKACJA NATURALNYCH SUBSTANCJI BARWIĄCYCH OBECNYCH W PRÓBKACH FARB ARTYSTYCZNYCH I TKANINACH POCHODZENIA HISTORYCZNEGO
PublikacjaNatural organic dyes are group of substances that belong to various types of chemical compounds. The most commonly used in paintings and dyeing textiles were naturally occurring dyestuffs from group of anthraquinones, flavones and indigoid dyes. Identification of coloring substances present in historical artistic paints provides relevant information for a wide range of specialists dealing with works of art and in the field of conservation science....
-
Application of Web-GIS and Cloud Computing to Automatic Satellite Image Correction
PublikacjaRadiometric calibration of satellite imagery requires coupling of atmospheric and topographic parameters, which constitutes serious computational problems in particular in complex geographical terrain. Successful application of topographic normalization algorithms for calibration purposes requires integration of several types of high-resolution geographic datasets and their processing in a common context. This paper presents the...
-
DESIGN AND STRENGTH CALCULATIONS OF THE TRIPOD SUPPORT STRUCTURE FOR OFFSHORE POWER PLANT
PublikacjaThe support structure being the object of the analysis presented in the article is Tripod. According to the adopted assumptions, it is a foundation gravitationally set in the water region of 60 m in depth, not fixed to the seabed, which can be used for installing a 7MW wind turbine. Due to the lack of substantial information on designing and strength calculations of such types of structures in the world literature, authors have...
-
Analysing selection of low-temperature medium for cogeneration micro power plant
PublikacjaThe article analyses the ORC system working with dry and wet low-boiling media which are most frequently used in installations of this type. Two types of cycles were examined, which were the cycle with heat regeneration for dry media: fc72, hfe7100, R227ea, R245fa, R423a and R600a, and the cycle without heat regeneration for wet media: R11, R12, R134a, R718 and 507a. The calculations were performed for the assumed required thermal...
-
Application of gamma densitometry and statistical signal analysis to gas phase velocity measurements in pipeline hydrotransport
PublikacjaThe work presents selected methods of signal analysis used in the processing of data obtained from radiometric probes. The used data came from an exemplary study of a two-phase liquid-gas flow at the laboratory installation. In such rigs many possible transport types may be observed, i.e. slug, plug and bubble flow, and each of them gives different signal-to-noise ratio of recorded data. Therefore, available radiometric methods...
-
Application of gamma densitometry and statistical signal analysis to gas phase velocity measurements in pipeline hydrotransport
PublikacjaThe work presents selected methods of signal analysis used in the processing of data obtained from radiometric probes. The used data came from an exemplary study of a two-phase liquid-gas flow at the laboratory installation. In such rigs many possible transport types may be observed, i.e. slug, plug and bubble flow, and each of them gives different signal-to-noise ratio of recorded data. Therefore, available radiometric methods...
-
Secondary arc modelling for single pole reclosing analyses
PublikacjaThe paper discusses two evaluation methods of single pole auto-reclosing process effectiveness in HV transmission lines. Secondary arc current and recovery voltage calculation results obtained by load flow calculation are compared to the results obtained by the time domain simulations. Moreover, a nonlinear secondary arc model implementation is presented. The paper presents the study results for the three types of EHV transmission...
-
Two tests for adhesive bonding long term characterization: principles and applications
PublikacjaThis article describes recent refinement of the traditional wedge test technique used to characterize durability of the adhesive joints. We propose two types of measuring protocols to monitor precisely and continuously the propagation of an "effective" crack during long term mode I fracture mechanic test. First method is directly derived from the traditional wedge test technique and consist in monitoring the surface strain of adherent...
-
Analysing selection of low-temperature medium for cogeneration micro power plant
PublikacjaThe article analyses the ORC system working with dry and wet low-boiling media which are most frequently used in installations of this type. Two types of cycles were examined, which were the cycle with heat regeneration for dry media: fc72, hfe7100, R227ea, R245fa, R423a and R600a, and the cycle without heat regeneration for wet media: R11, R12, R134a, R718 and 507a. The calculations were performed for the assumed required thermal...
-
Mechanical compatibility of implants used in hernia repair with abdominal wall
PublikacjaThe paper deals with a membrane model of a synthetic surgical mesh for treatment of abdominal hernia. The authors analyse the compatibility of two implant types with the human wall: Dualmesh Gore and Proceed. The finite element method is applied to simulate tjhe behavior of the proposed model. Due fact that recurrences are usually caused by connection failure, this study is focused on reaction forces in supports representing the...
-
Methods of assaying volatile oxygenated organic compounds in effluent samples by gas chromatography—A review
PublikacjaThe paper is a review of the procedures for the determination of volatile and semivolatile oxygenated organic compounds (O-VOCs) in effluent samples by gas chromatography. Current trends and outlook for individual steps of the procedure for the determination of O-VOCs in effluents are discussed. The available sample preparation techniques and their limitations are described along with GC capillary columns used for O-VOCs separation...
-
Global Complex Roots and Poles Finding Algorithm Based on Phase Analysis for Propagation and Radiation Problems
PublikacjaA flexible and effective algorithm for complex roots and poles finding is presented. A wide class of analytic functions can be analyzed, and any arbitrarily shaped search region can be considered. The method is very simple and intuitive. It is based on sampling a function at the nodes of a regular mesh, and on the analysis of the function phase. As a result, a set of candidate regions is created and then the roots/poles are verified...
-
Accelerator of the entrepreneurship: suburbs in the coastal metropolis of GOM
PublikacjaPolish model of suburban structure is made of variety types of enterprises in different scales, and a range of housing. However this mass of unordered structure with its urban development problems, often leads to the establishment of business and also the development of local entrepreneurship. This article investigates SME sector located in the suburban area of costal metropolis GOM to prove the thesis that the positive effect...
-
Degradation of reference tyres used for CPX measurements
PublikacjaMeasurements of tyre/road noise using the Close Proximity Method are based on reference tyres that are described in ISO/TS 11819-3. The standard specifies two tyres, namely "P1" and "H1" that should be used during measurements. To be used for measurements each tyre must fulfill certain conditions that are listed in the standard. The conditions are related to the tread pattern depth and rubber hardness. During experiments performed...
-
Move into the open space – what can we expect from moving artistic interventions to open urban spaces?
PublikacjaThe paper discuses the role of incorporating creative engagement into the processes of urban and social development using cultural means of action and expression and the potential of artistic interventions in public space. The block of initiatives within the People’s Smart Sculpture EU project, realized by Gdańsk City Gallery, has been named “Move Into The Open Space”. This paper will provide...
-
Thermoplastic polyurethane/(organically modified montmorillonite) nanocomposites produced by in situ polymerization
PublikacjaA series of polyurethane nanocomposites were synthesized from thermoplastic polyurethanes (with different hard segment ratios) and two types of organically modified montmorillonites (OMMT) - Cloisite® 10A and Cloisite® 20A. The thermal behavior was examined by non-isothermal thermogravimetry (TG, DTG), Differential Scanning Calorimetry (DSC) and Dynamic-Mechanical Thermal Analysis (DMTA). The results of X-ray analyses showed that...
-
An inclination in Thermal Energy Using Nanoparticles with Casson Liquid Past an Expanding Porous Surface
PublikacjaPhysical aspects of inclined MHD nanofluid towards a stretching sheet embedded in a porous medium are visualized. Two types of nanoparticles are used named as copper and alumna dioxide with water as base fluid. Similarity transformations are used to convert the partial differential equations into the set of ordinary differential equation. Closed solutions are found to examine the velocity and the temperature profiles. It is examined...
-
Membranes for toxic- and heavy-metal removal
PublikacjaSince time ago, membranes have greatly attracted the attention of researchers for different types of water-treatment applications, such as wastewater treatment, water purification, removal of microorganisms, chemical compounds, and heavy metals. Nowadays, one of the current challenges of research community definitely deals with the removal of toxic and heavy metals from water. In this regard, the current chapter provides enough...
-
Analiza nośności zabytkowych fundamentów w kontekście jakości użytych zapraw Analysis of the Load-Bearing Capacity of Historical Foundations in the Context of the Quality of Mortar Used
PublikacjaStructures of historical buildings usually have the form of masonry elements. The weakest component of such elements is mortar, especially in stone foundations, which were often used in the with a focus on the modeling of mortar as a joint connecting stones in a characteristic medieval foundation. Different types of mortar: cement, cement-lime, lime and gypsum mortars, were examined. A numerical analysis was carried out on the...
-
Nonlinear strain gradient and micromorphic one-dimensional elastic continua: Comparison through strong ellipticity conditions
PublikacjaWe discuss the strong ellipticity (SE) conditions for strain gradient and micromorphic continua considering them as an enhancement of a simple nonlinearly elastic material called in the following primary material. Recently both models are widely used for description of material behavior of beam-lattice metamaterials which may possess various types of material instabilities. We analyze how a possible loss of SE results in the behavior...
-
Signals Features Extraction in Radioisotope Liquid-Gas Flow Measurements using Autocorrelation Function
PublikacjaKnowledge of the two-phase flow structure is essential for the proper conduct of industrial processes. Description of liquid-gas flow regimes is possible by using of data analysis in time, frequency, or state-space domain. In this research studies, the autocorrelation function is applied for analysis of signals obtained for liquid-gas flow by use gamma-ray absorption. The experiments were carried out on the laboratory hydraulic...
-
CSR and innovation or CSR as non-technological innovation
PublikacjaThis chapter investigates the relationship between Corporate Social Responsibility (CSR) and innovation process. There is an ongoing discussion in the literature regarding this relationship, in particular on its one- or bidirectional nature and possible antecedents or mediating factors. This research addresses this gap and aims to provide more conceptual clarity and synthesize the different types of relationships between CSR and...
-
Green thermoplastic poly(ether-urethane)s – synthesis, chemical structure and selected properties investigation
PublikacjaThis work aimed to characterize the effect of the monomers chemical structure on the selected properties of the green thermoplastic poly(ether-urethane)s. During synthesis two types of polyether biopolyols, 4,4′-diphenylmethane diisocyanate and bio-based 1,3-propanediol were employed. Materials were synthesized with the use of two step method and two different prepolymers, which were mixed together in equimolar quantities. Obtained...
-
Nonlinear Influence of Sound on the Vibrational Energy of Molecules in a Relaxing Gas
PublikacjaDynamics of a weakly nonlinear and weakly dispersive flow of a gas where molecular vibrational relaxation takes place is studied. Variations in the vibrational energy in the field of intense sound is considered. These variations are caused by a nonlinear transfer of the acoustic energy into energy of vibrational degrees of freedom in a relaxing gas. The final dynamic equation which describes this is instantaneous, it includes a...
-
Design and Configuration of Context-aware VoIP Telephony Systems
PublikacjaVoice over IP is a widely used concept with regard to a realization technology of different types of telephony systems, including those that are used in enterprises. Such systems of a call procesing component and a set of desk endpoints that are pervasove from a user perspective. Those andpoints are usually not mobile, but in result can deliver a much greater set of functions needed in an everyday office work. Those functions also...
-
Recognition and sensing of anions
PublikacjaMolecular ion recognition is one of the most intensively studied areas of supramolecular technology. The reason for this is the essential role that ions play in many biological as well as industrial processes. On the other hand, however, it has been proved that ions can have a negative impact on human health and the environment. For these reasons, it is extremly important to develop rapid and simple methods allowing the determination...
-
Influence of laser melting on surface layer properties of titanium alloy Ti6Al4V
PublikacjaIn time of rapid technology and medicine progress, implants are becoming more widely used in the human body, ranging from dental implants, stabilizing plates, screws, orthopaedic prostheses. For example, there are many types of hip prostheses used for hip replacement as well as various types of materials used for these orthopaedic prostheses. Properties of titanium alloys used in hip prostheses combined with good strength properties,...
-
Improving platelet‐RNA‐based diagnostics: a comparative analysis of machine learning models for cancer detection and multiclass classification
PublikacjaLiquid biopsy demonstrates excellent potential in patient management by providing a minimally invasive and cost-effective approach to detecting and monitoring cancer, even at its early stages. Due to the complexity of liquid biopsy data, machine-learning techniques are increasingly gaining attention in sample analysis, especially for multidimensional data such as RNA expression profiles. Yet, there is no agreement in the community...
-
Designing a High-sensitivity Microscale Triple-band Biosensor based on Terahertz MTMs to provide a perfect absorber for Non-Melanoma Skin Cancer diagnostic
PublikacjaNon-melanoma skin cancer (NMSC) is among the most prevalent forms of cancer originating in the top layer of the skin, with basal cell carcinoma (BCC) and squamous cell carcinoma (SCC) being its primary categories. While both types are highly treatable, the success of treatment hinges on early diagnosis. Early-stage NMSC detection can be achieved through clinical examination, typically involving visual inspection. An alternative,...