Filtry
wszystkich: 1186
wybranych: 1085
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: FINITE ELEMENT METHOD,REDUCTION
-
Non-Linear Analysis of Inter-Story Pounding between Wood-Framed Buildings during Ground Motion
PublikacjaPounding between adjacent buildings during ground motion may result in structural damage or lead to total destruction of structures. The research on the phenomenon has recently been much advanced; however, the analyses have been carried out only for concrete, steel, and masonry structures, while pounding between wooden buildings has not been studied so far. The aim of this paper is to show the results of detailed non-linear seismic...
-
Non-uniqueness of fracture parameter choice in simulations of concrete cracking at mesoscale level
PublikacjaIn the paper a non-uniqueness of fracture parameter choice in simulations of cracking process in plain concrete specimens at mesoscale level under monotonic static loading is analysed. The Finite Element Method is used, where cracks are defined in a discrete way using interface cohesive elements with nonlinear material law including softening. The concrete mesostructure (such as: cement matrix, air voids, aggregates, and Interfacial...
-
Non-Destructive Testing of the Longest Span Soil-Steel Bridge in Europe—Field Measurements and FEM Calculations
PublikacjaThe article describes interdisciplinary and comprehensive non-destructive diagnostic tests of final bridge inspection and acceptance proposed for a soil-steel bridge made of corrugated sheets, being the European span length record holder (25.74 m). As an effect of an original concept a detailed and precise information about the structure short-term response was collected. Periodic diagnostics of bridge deformations was done one...
-
Nonlinear dynamic analysis of the pure “buckling” mechanism during blow-out trauma of the human orbit
PublikacjaConsidering the interplay between orbital bones and intraorbital soft tissues, commonly accepted patterns of the blow-out type of trauma within the human orbit require more thorough investigation to assess the minimal health-threatening impact value. Two different three-dimensional finite element method (FEM) models of the human orbital region were developed to simulate the pure “buckling” mechanism of orbital wall fracture in...
-
Tensile validation tests with failure criteria comparison for various GFRP laminates
PublikacjaThe paper studies the mechanical properties of glass fibre reinforced polymers (GFRP) with various types and orientation of reinforcement. Analyzed specimens manufactured in the infusion process are made of polymer vinyl ester resin reinforced with glass fibres. Several samples were examined containing different plies and various fibres orientation [0, 90] or [+45, –45]. To assess the mechanical parameters of laminates, a series...
-
SFEM Analysis of Beams with Scaled Lengths including Spatially Varying and Cross-Correlated Concrete Properties
PublikacjaThis paper presents the results obtained for plain concrete beams under four-point bending with spatially varying material properties. Beams of increasing length but constant depth were analyzed using the stochastic finite element method. Spatial fluctuation of a uniaxial tensile strength, fracture energy and elastic modulus was defined within cross-correlated random fields. The symmetrical Gauss probability distribution function...
-
Numerical analysis of elastic wave propagation in unbounded structures
PublikacjaThe main objective of this paper is to show the effectiveness and usefulness of the concept of an absorbing layer with increasing damping (ALID) in numerical investigations of elastic wave propagation in unbounded engineering structures. This has been achieved by the authors by a careful investigation of three different types of structures characterised by gradually increasing geometrical and mathematical description complexities....
-
Mechatronic Design Towards Investigation of the Temporo-Mandibular Joint Behaviour
PublikacjaA significant problem of the temporo-mandibular joint (TMJ) research is lack of data concerning geometry and position of TMJ discs. It leads to necessity of developing a driving method of the process optimization, which is based on chosen techniques of mechatronic design. In particular, the latter concerns a technique of experimentally supported virtual prototyping. On this stage, the research is characterized by well-verified...
-
The influence of selected strain-based failure criteria on ship structure damage resulting from a collision with an offshore wind turbine monopile
PublikacjaOffshore wind farms are developing well all over the world, providing green energy from renewable sources. The evaluation of possible consequences of a collision involves Finite Element computer simulations. The goal of this paper was to analyse the influence of selected strain-based failure criteria on ship damage resulting from a collision with an offshore wind turbine monopile. The case of a collision between an offshore supply...
-
Synthesis and properties of porous Sr 0.96 Y 0.04 Ti 1−x Nb x O 3
PublikacjaA series of porous, single phase Sr0.96Y0.04Ti1-xNbxO3 samples was obtained using a wet synthesis method (modified citrate sol-gel) method. Temperature-programmed reduction (TPR) and temperature-programmed oxidation (TPO) measurements have shown high stability of the obtained material in variable (oxidizing/reducing) atmospheres. All samples exhibit high conductivity in hydrogen atmosphere with the highest value (around 1S/cm)...
-
Novel method for metal-oxide glass composite fabrication for use in thermoelectric devices
PublikacjaA novel method for thermoelectric materials fabrication using a reduction of oxide precursors in hydrogen was reported. On the example of Bi-Sb, Bi-Sb-Te and Te-Ag-Ge-Sb compounds it was shown that this simple and easy method is suitable for fabrication of two-, three- and even multicomponent thermoelectric materials. It allows controlling a composition, microstructure and even type a of electrical charge carriers. As a result...
-
Modelowanie przepływu ustalonego niejednostajnego w sieciach kanałów otwartych z uwzględnieniem obiektów hydrotechnicznych
PublikacjaW pracy sformułowano zagadnienie brzegowe dla równania energii opisującego przepływ ustalony niejednostajny i przedstawiono sposób jego rozwiązania przy pomocy metody różnicowej. Zaproponowana metoda obliczeń nadaje się do analizy przepływu w dendrycznych i pierścieniowych sieciach kanałów otwartych. Ponadto na przykładzie przelewu prostokątnego zaproponowano metodę uwzględnienia w obliczeniach zabudowy hydrotechnicznej. Słowa...
-
Investigation on accelerated impedance spectrum measurement method with multisine signal stimulation
PublikacjaThe paper presents an investigation on the accelerated impedance spectrum measurement method, oriented at parameter identification of technical objects modelled by a linear equivalent circuit, e.g. anticorrosion coatings.The method is based on multisine signal stimulation of an object and response analysis by triangle window filterbanks.It has several advantages, as compared with conventional point-by-point spectrum measurement....
-
Hybrid Technique Combining the FDTD Method and Its Convolution Formulation Based on the Discrete Green's Function
PublikacjaIn this letter, a technique combining the finite-difference time-domain (FDTD) method and its formulation based on the discrete Green's function (DGF) is presented. The hybrid method is applicable to inhomogeneous dielectric structures that are mutually coupled with wire antennas. The method employs the surface equivalence theorem in the discrete domain to separate the problem into a dielectric domain simulated using the FDTD method...
-
Isogeometric Shell FE Analysis of the Human Abdominal Wall
PublikacjaIn this paper a nonlinear isogeometric Kirchhoff-Love shell model of the human abdominal wall is proposed. Its geometry is based on in vivo measurements obtained from a polygon mesh that is transformed into a NURBS surface, and then used directly for the finite element analysis. The passive response of the abdominal wall model under uniform pressure is considered. A hyperelastic membrane model based on the Gasser-Ogden-Holzapfel...
-
Dynamics of mechanical model of implant-tissue system in ventral hernia repair
PublikacjaThe paper deals with a finite element modelling of implants in the problem of ventral hernia repair. The synthetic mesh implanted in the abdomen during surgery is here modelled as a membrane structure. Thesystem undergoes the internal abdominal pressure that occurs during the postoperative cough, the load identified in the literature as the main cause of the connection failure and hernia recurrence. The model can be used to estimate...
-
Buckling analyses of metal cylindrical silos containing bulk solids during filling
PublikacjaThe paper presents 3D results on stability of thin-walled cylindrical metal silos made of isotropic rolled and corrugated plates containing bulk solids. The behavior of bulk solids was described using a hypoplastic constitutive model. Nonlinear finite element (FE) analyses with both geometric and material nonlinearity were performed with a perfect and an imperfect silo shell wherein initial geometric imperfections were taken into...
-
Regularized Identification of Time-Varying FIR Systems Based on Generalized Cross-Validation
PublikacjaA new regularization method is proposed and applied to identification of time-varying finite impulse response systems. We show, that by a careful design of the regularization constraint, one can improve estimation results, especially in the presence of strong measurement noise. We also show that the the most appropriate regularization gain can be found by direct optimization of the generalized cross-validation criterion.
-
A method to determine the tightening sequence for standing rigging of a mast
PublikacjaThe article proposes an alternative method to determine the sequence of generation of pre-tension forces in standing rigging of a mast. The proposed approach has been verified on both a virtual simulation experiment and laboratory tests. In this method, the desired tension values are obtained using the influence matrix which allows to calculate the effect of tension change in an individual rope on the tension distribution in the...
-
Hybridization of the FDTD method with use of the discrete Green's function
PublikacjaIn this contribution, a hybrid technique is presented which combines the finite-difference time-domain (FDTD) method and the discrete Green's function (DGF) formulation of this method. FDTD is a powerful technique for the analysis of complex penetrable objects but its application is not efficient when the computational domain includes many free-space cells. Therefore, the hybrid method was developed which is applicable to complex...
-
Design considerations for compact microstrip resonant cells dedicated to efficient branch-line miniaturization
PublikacjaA conventional compact microstrip resonant cell (CMRC)has been thoroughly investigated to enhance its slow-wave properties and subsequently ensure an efficient miniaturization of a microstrip circuit. The geometry of a classic CMRC has been improved in terms of slowwave effect in two progressive steps: (i) a single-element topology has been replaced with a double-element one and (ii) a high-impedance section has been refined by...
-
Numerically efficient algorithm for compact microwave device optimization with flexible sensitivity updating scheme
PublikacjaAn efficient trust-region algorithm with flexible sensitivity updating management scheme for electromagnetic (EM)-driven design optimization of compact microwave components is proposed. During the optimization process, updating of selected columns of the circuit response Jacobian is performed using a rank-one Broyden formula (BF) replacing finite differentiation (FD). The FD update is omitted for directions sufficiently well aligned...
-
EXPERIMENTAL AND NUMERICAL VALIDATION OF THE IMPROVED VORTEX METHOD APPLIED TO CP745 MARINE PROPELLER MODEL
PublikacjaThe article presents a numerical analysis of the CP745 marine propeller model by means of the improved vortex method and CFD simulations. Both numerical approaches are validated experimentally by comparing with open water characteristics of the propeller. The introduced modification of the vortex method couples the lifting surface approach for the propeller blades and the boundary element method for the hub. What is more, a...
-
Parallel implementation of the DGF-FDTD method on GPU Using the CUDA technology
PublikacjaThe discrete Green's function (DGF) formulation of the finite-difference time-domain method (FDTD) is accelerated on a graphics processing unit (GPU) by means of the Compute Unified Device Architecture (CUDA) technology. In the developed implementation of the DGF-FDTD method, a new analytic expression for dyadic DGF derived based on scalar DGF is employed in computations. The DGF-FDTD method on GPU returns solutions that are compatible...
-
On degradation of glass/polyester laminate immersed in water
PublikacjaMechanical behaviour was compared for glass/ polyester laminates manufactured in the boatbuilding plant using three methods: hand lay-up, vacuum bagging, infusion. Specimens were tested in dry condition and following accelerated water immersion test (70°C- corresponding to the exposure of 30 years at 19°C). In three point bending test 40-50% reduction in laminate strength was observed due to water immersion. The highest degradation...
-
Does the carbon emissions trading system reduce carbon emissions by promoting two-way FDI in developing countries? Evidence from Chinese listed companies and cities
PublikacjaHow developing countries can effectively promote cities’ carbon emission reduction through the carbon emission trading system (ETS) is a topic worthy of attention in the global carbon reduction campaign. Policy changes in China's ETS provide a unique opportunity to measure whether ETS impacts carbon emissions through two-way FDI. Hence, this paper employs difference-in-differences (DID) method to test the causal impact of ETS...
-
Influence of the notch rounding radius on estimating the elastic notch stress concentration factor in a laser welded tee joint
PublikacjaIn recent years an increased interest of industry in sandwich-type metal structures can be observed. These structures consist of thin plates of 2.5 mm in thickness separated by stiffeners of different shapes and forms. Welds joining the plates and stiffeners are made on the outer side of the plates using laser welding technique. A locally focused source of heat causes the plate to melt creating a very narrow and elongated joint....
-
TB11 test for short w-beam road barrier
PublikacjaFEM (Finite Element Method) is well-suited and widely used tool for simulating a range of phenomena: from these with simple and static behaviour, up to those complicated, highly nonlinear and involving many contacts. In present paper we use one of the advantages of FEM: parametric study could be easily performed and is more economical than series of in-situ tests. If recommended practices is carefully followed, results obtained...
-
Technical fabrics in costruction of large scale roofs - numerical and experimental aspects
PublikacjaDesigning and construction of textile hanging roofs is the challenging subject for engineers. This type of structure needs geometrically and very often also physically non-linear calculations. Due to different behaviour of two families of threads (warp and weft), which during deformation can change the angle between their directions, they require special constitutive modelling. Also the loading of hanging roofs is very special....
-
Soil-structure interaction effects on modal parameters of office buildings with different number of stories
PublikacjaThe paper summarizes the results of a numerical investigation designed to study the soil-structure interaction effects on modal parameters of three office buildings. The reinforced-concrete 4-storey, 8-storey, and 12-storey office buildings, each with additional two levels of embedded basements, represent low, medium, and high-rise structures, respectively. In order to conduct this research, detailed finite-element structure models...
-
Equivalent single-layer models in deformation analysis of laminated multilayered plates
PublikacjaThe performance of selected Equivalent Single-Layer (ESL) models is evaluated within several classical benchmark tests for linear static analysis of multi-layered plates. The authors elaborated their own Finite Element software based on the first-order shear deformation theory (FOSD) with some modifications incorporated including a correction of the transverse shear stiffness and an application of zig-zag type functions. Seven...
-
Three-point bending test of sandwich beams supporting the GFRP footbridge design process - validation
PublikacjaSome selected aspects concerning material and construction design issues for pedestrian footbridge made of GFRP composite materials are elaborated in this paper. The analysis is focused on validation tests, which are particularly important because of the advanced technology and materials that are used for this innovative bridge. The considered footbridge is a sandwich-type shell structure comprising of PET foam core and outer skins...
-
Direct algorithm for optimizing robust MPC of drinking water distribution systems hydraulics
PublikacjaModel-based predictive control is an effective method for control the large scale systems [1]–[6], [8], [16], [17]. Method is based on on-line solution of the control task over the control horizon using current and past measurements, as well as the system model. Only a first element of calculated control sequence is applied to the plant. At the next sampling instant, based on new process output measurements, control procedure is...
-
Structural reliability of overhead power lines by means of Monte Carlo Method and RSM
PublikacjaThe article discusses the issue of reliability assessment of overhead power lines by means of both Monte Carlo Method and Response Surface Method. The suspension tower OS24 ON150+10 is considered, as the weakest element of the line. A comparison is made between deterministic and probabilistic approaches to wind and icing loading. The PDFs for wind and icing loads are proposed. Reliability is assessed for both critical atmospheric...
-
The Effect of the Selection of Three-Dimensional Random Numerical Soil Models on Strip Foundation Settlements
PublikacjaThis paper delivers a probabilistic attempt to prove that the selection of a random three-dimensional finite element (FE) model of a subsoil affects the computed settlements. Parametricanalysis of a random soil block is conducted, assuming a variable subsoil Young’s modulus inparticular finite elements. The modulus is represented by a random field or different-sized setsof random variables; in both cases, the same truncated...
-
A compact seven-section rat-race hybrid coupler incorporating pbg cells
PublikacjaA conventional rat-race coupler has been doubly miniaturized: (i) characteristic impedances and electrical lengths of microstrip sections have been adequately modified as the first step of size reduction and (ii) T-shaped PBG cells have been implemented to diminish strip section length as the second step of circuit rat-race couplerminiaturization. The experimental results show good agreement with theoretical characteristics. Furthermore,...
-
Structure and thermoelectric properties of Cs-Bi-Te alloys fabricated by different routes of reduction of oxide reagents
PublikacjaCesium-bismuth-telluride polycrystalline materials were fabricated using a cost-effective method based on a reduction of oxide reagents, leading to a production of a material with good thermoelectric properties. Several samples with various initial stoichiometry were prepared by melting of oxide powders at 1050 °C, quenching, milling to powders and then reducing in pure hydrogen at 400 °C. Another concept was to obtain the CsBi4Te6...
-
Generalized Chebyshev Bandpass Filters With Frequency-Dependent Couplings Based on Stubs
PublikacjaThis paper presents an accurate synthesis method for inline and cross-coupled generalized Chebyshev bandpass filters with frequency-dependent couplings implemented via open and short stubs. The technique involves the synthesis of a lumped-element prototy pe in the form of a coupling matrix with a frequency-dependent term and the conversion of this prototype to a distributed-element mode l composed of sections of TEM lines. This...
-
Accurate Computation of IGBT Junction Temperature in PLECS
PublikacjaIn the article, a new method to improve the accuracy of the insulated-gate bipolar transistor (IGBT) junction temperature computations in the piecewise linear electrical circuit simulation (PLECS) software is proposed and described in detail. This method allows computing the IGBT junction temperature using a nonlinear compact thermal model of this device in PLECS. In the method, a nonlinear compact thermal model of the IGBT is...
-
Evaluating the effectivness of an outsourced processes on the basis of key performance indicators
PublikacjaAccording to the statistics outsourcing has become typical solution for mature economies. Besides short run attempt based on cost reduction, getting popular is the method of increasing the effectiveness by implementing outsourced process. Authors in this article present the methods of measuring outsourcing performance on the basis of key performance indicators.
-
Treatment of bitumen post oxidative effluents by sulfate radicals based advanced oxidation processes (S-AOPs) under alkaline pH conditions
PublikacjaSulfate radicals based Advanced Oxidation Processes (S-AOPs), namely Persulfate and peroxymonosulfate, were used for the treatment of post oxidative effluents from a production of petroleum bitumens under alkaline pH. Studies on the identification and monitoring of the volatile organic compounds (VOCs) along with COD, BOD and sulfide ions reduction were performed. Persulfate with a ratio between the oxygen from the oxidant and...
-
Modification of structured bio‑carbon derived from spongin-based scaffolds with nickel compounds to produce a functional catalyst for reduction and oxidation reactions: Potential for use in environmental protection
PublikacjaThree different 3D fibrous-like NiO/Ni(OH)2/Ni‑carbonized spongin-based materials were prepared via a simple sorption–reduction method. Depending on the support used, the catalysts were composed of carbon, nickel oxide, nickel hydroxide and zero-valent nickel, with the surface content of the nickel-containing phase in the range 15.2–26.0 wt%. Catalytic studies showed promising activity in the oxidation of phenolic compounds in water...
-
The calculation long-term physical field created by water flow around the ship
PublikacjaThe paper presents a description of the problems with fluid flow around a ship. Using the described solution of the problem were performed numerical calculations using the boundary element method. Were also presented preliminary results of the calculation of pressure fields at the bottom of the ship, taking into account the impact of the bottom.
-
ECHOES REDUCTION DURING DIGITAL DATA TRANSMISSION IN HYDROACOUSTIC CHANNEL – LABORATORY EXPERIMENT
PublikacjaThe possibility of using a hydroacoustic channel for digital data transmission is very limited. This is due to the effect of multipath propagation of the emitted acoustic wave and the damping of the mechanical wave in this medium, which increase with frequency. The first of these phenomena results in inter-symbol interference disturbances in data transmission systems, including even hundreds of symbols. Due to the number of reflections...
-
Compressible gas density measurement by means of Fourier analysis of interferograms
PublikacjaThis paper describes a method for nonintrusive compressible gas density measurement by means of automated analysis of interferograms using FFT (Fast Fourier Transform), and its implementation using DFT (Discrete Fourier Transform), that does make this measurement technique a fairly valuable and accessible experimental method. The presented approach makes it possible to use the finite fringe setting of the interferometer, thus reducing...
-
Impact of cross-section centers estimation on the accuracy of the Point cloud spatial expansion using robust M-estimation and Monte Carlo simulation
PublikacjaThe point cloud spatial expansion (PCSE) method creates an alternative form of representing the shape of symmetrical objects and introduces additional descriptive geometric parameters. An important element of the procedure is determining the course of the axis of symmetry of cylindrical objects based on cross-sections of point clouds. Outliers occurring in laser measurements are of great importance in this case. In this study,...
-
Modular Approach for Modelling Warming Up Process in Water Installations with Flow-Regulating Elements
PublikacjaThe paper presents a new method for modelling the warming up process of a water system with elements regulating the flow in a stochastic manner. The paper presents the basic equations describing the work of typical elements which the water installation is composed of. In the proposed method, a new computational algorithm was used in the form of an iterative procedure enabling the use of boundary conditions that can be stochastically...
-
Biomimetic torene shells
PublikacjaThe genome inside the eukaryotic cells is guarded by a unique shell structure, called the nuclear envelope (NE), made of lipid membranes. This structure has an ultra torus topology with thousands of torus-shaped holes that imparts the structure a high flexural stiffness. Inspired from this biological design, here we present a novel ‘‘torene’’ architecture to design lightweight shell structures with ultra-stiffness for engineering...
-
Adhesive compliance effect in mode I separation:Profilometry approach
PublikacjaThe effect of adhesive compliance on the deflection of a loaded, bonded beam was studied using laser profilometry. Experimental data obtained were compared with both Euler-Bernoulli (encastré) and Winkler (one parameter elastic foundation) models. A third, analytical, 2D model, based on shear within the adhesive layer (two parameter elastic foundation), was introduced. Finite element analysis (FEA) was also used to study the effect...
-
Global sensitivity analysis of membrane model of abdominal wall with surgical mesh
PublikacjaThe paper addresses the issue of ventral hernia repair. Finite Element simulations can be helpful in the optimization of hernia parameters. A membrane abdominal wall model is proposed in two variants: a healthy one and including hernia defect repaired by implant. The models include many uncertainties, e.g. due to variability of abdominal wall, intraabdominal pressure value etc. Measuring mechanical properties with high accuracy...