Filtry
wszystkich: 1688
wybranych: 1218
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: VITAL SIGNS ESTIMATION
-
Algorithm for Automatic Wear Estimation of Railway Contact Strips Based on 3D Scanning Results
PublikacjaElectric rail vehicles use current collection system which consists of overhead contact line and a current collector (pantograph) mounted on the roof of a vehicle. A pantograph is equipped with contact strips, which slide along the contact wire, ensuring steady electric contact. Contact strips are made of carbon layer, fixed to an aluminum carrier. The carbon layer wears down due to friction. Using overly worn contact strips increases...
-
The use of Response Surface Methodology for reliability estimation of aluminum silo subjected to wind load
PublikacjaAn axisymmetric aluminum silo model with a single, standardized geometric imperfection of its lateral surface is considered. The silo is wind – loaded only. The paper is focused on the critical, or limit value of wind pressure, both producing a loss of stability of the silo. This value is affected by vertical coordinate (position) of the imperfection and the angular relation between the imperfection and the wind direction. Reliability...
-
Numerical estimation of the pile toe and shaft unit resistances during the installation process in sands
PublikacjaNumerical simulations of a pile jacking were carried out. A Coupled Eulerian–Lagrangian (CEL) formulation was used to treat with large deformation problems. An Abaqus, a commercial Finite Element Method software suit, was used as a computing environment. The Mohr–Coulomb constitutive model was applied and the Coulomb model of friction was used to describe pile-soil interaction. Calculations were made for three different pile diameters....
-
Estimation of the effectiveness of nbpt for limiting ammonia emission from urea based on the field experiments
PublikacjaThe efectiveness of the ammonia emission reduction from NBPT-stabilized urea was investigating in 2011 during a field experiment on a grassland plot fertilized with a one-time dose of 60 kgN/ha. The obtained reduction coefficient of ammonia emission equaled 73% and 39-51% relative to erea without the inhibitor and ammonium nitrate, respectively.
-
Improved magnitude estimation of complex numbers using alpha max and beta min algorithm
PublikacjaThe paper presents an improved algorithm for calculating the magnitude of complex numbers. This problem, which is a special case of square rooting, occurs for example, in FFT processors and complex FIR filters. The proposed method of magnitude calculation makes use of the modified alpha max and beta min algorithm. The improved version of the algorithm allows to control the maximum magnitude approximation error by using an adequate...
-
Innovative consciousness and threats estimation connected with implementation of innovations to SMEs cooperating with shipbuilding industry
PublikacjaPodejmowanie działań innowacyjnych przez małe i średnie przedsiębiorstwa nie jest szeroko rozpowszechnione. Wynika to, między innymi, ze specyfiki tego sektora. MSP często dysponują ograniczonymi środkami finansowymi i nisko wykwalifikowanymi pracownikami, co stanowi w wielu przypadkach barierę we wprowadzaniu innowacji. Nie mniej istotne są inne podmioty działające w otoczeniu MSP włączające się w realizacje procesu innowacyjnego....
-
A Proposed Soft Computing Model for Ultimate Strength Estimation of FRP-Confined Concrete Cylinders
PublikacjaIn this paper, the feed-forward backpropagation neural network (FFBPNN) is used to propose a new formulation for predicting the compressive strength of fiber-reinforced polymer (FRP)-confined concrete cylinders. A set of experimental data has been considered in the analysis. The data include information about the dimensions of the concrete cylinders (diameter, length) and the total thickness of FRP layers, unconfined ultimate concrete...
-
Non-Adaptive Rotor Speed Estimation of Induction Machine in an Adaptive Full-Order Observer
PublikacjaIn the sensorless control system of an induction machine, the rotor speed value is not measured but reconstructed by an observer structure. The rotor speed value can be reconstructed by the classical adaptive law with the integrator. The second approach, which is the main contribution of this paper, is the non-adaptive structure without an integrator. The proposed method of the rotor speed reconstruction is based on an algebraic...
-
Estimation of the aluminum salt effect on homopolymerization of acrylamide and its copolymerization with acrylic acid by DSC
Publikacja -
ESCASA : Analytical estimation of atomic coordinates from coarse‐grained geometry for nuclear‐magnetic‐resonance ‐assisted protein structure modeling. I. Backbone and Hβ protons
PublikacjaA method for the estimation of coordinates of atoms in proteins from coarse-grained geometry by simple analytical formulas (ESCASA), for use in nuclear-magnetic-resonance (NMR) data-assisted coarse-grained simulations of proteins is proposed. In this paper, the formulas for the backbone Hα and amide (HN) protons, and the side-chain Hβ protons, given the Cα-trace, have been derived and parameterized, by using the interproton distances...
-
High performance super-twisting sliding mode control for a maritime autonomous surface ship (MASS) using ADP-Based adaptive gains and time delay estimation
PublikacjaThis research addresses two kinds of problems related to optimal trajectory tracking of a Maritime Autonomous Surface Ship (MASS): those caused by the time-varying external disturbances including winds, waves and ocean currents as well as those resulting from inherent dynamical uncertainties. As the paper shows, an accurate and robust optimal controller can successfully deal with both issues. An improved Optimal Adaptive Super-Twisting...
-
High performance super-twisting sliding mode control for a maritime autonomous surface ship (MASS) using ADP-Based adaptive gains and time delay estimation
PublikacjaThis research addresses two kinds of problems related to optimal trajectory tracking of a Maritime Autonomous Surface Ship (MASS): those caused by the time-varying external disturbances including winds, waves and ocean currents as well as those resulting from inherent dynamical uncertainties. As the paper shows, an accurate and robust optimal controller can successfully deal with both issues. An improved Optimal Adaptive Super-Twisting...
-
Estimation of Failure Initiation in Laminated Composites by means of Nonlinear Six-Field Shell Theory and FEM
PublikacjaThe monography deals with the problem of failure initiation in thin laminated composites. Known techniques of laminate structures modelling are briefly characterised. Eventually, shell based approach is chosen for the purpose of the description of the composite structures behaviour, as it predicts their deformation and states of stress effectively in a global sense. The nonlinear six parameter shell theory (6p theory) with asymmetric...
-
Deep neural networks for human pose estimation from a very low resolution depth image
PublikacjaThe work presented in the paper is dedicated to determining and evaluating the most efficient neural network architecture applied as a multiple regression network localizing human body joints in 3D space based on a single low resolution depth image. The main challenge was to deal with a noisy and coarse representation of the human body, as observed by a depth sensor from a large distance, and to achieve high localization precision....
-
Estimation of the angular position of a two-wheeled balancing robot using a real IMU with selected filters
PublikacjaA low-cost measurement system using filtering of measurements for two-wheeled balancing robot stabilisation purposes has been addressed in this paper. In particular, a measurement system based on gyroscope, accelerometer, and encoder has been considered. The measurements have been corrected for deterministic disturbances and then filtered with Kalman, α-β type, and complementary filters. A quantitative assessment of selected filters...
-
Matrix Strengthening the Identification of Observations with Split Functional Models in the Squared Msplit(q) Estimation Process
Publikacja -
Deformation Analysis of Geodetic Networks by Applying M split Estimation with Conditions Binding the Competitive Parameters
Publikacja -
Set membership estimation of parameters and variables in dynamic networks by recursive algorithms with moving measurment window
PublikacjaW artykule rozważana jest łączna estymacja przedziałowa zmiennych i parametrów w złożonej sieci dynamicznej w oparciu niepewne modele parametryczne i ograniczoną liczbę pomiarów. Opracowany został rekursywny algorytm estymacji z przesuwnym oknem pomiarowym, odpowiedni dla monitorowania sieci on-line. Okno pomiarowe pozwala na stabilizowanie klasycznego algorytmu rekurencyjnego estymacji i znacznie poprawienie obcisłości estymat....
-
Mixed algorithm in searches of mechanical system steady-state conditions for low precision of the state estimation
PublikacjaW pracy zaprezentowano algorytm poszukiwania rozwiązania układu równań nieliniowych. Nieliniowe funkcje lewych stron znane są z ograniczoną dokładnością, a wzory określające ich pochodne względem czasu nie są znane. Wartości pochodnych wyznaczane są numerycznie za pomocą różnic skończonych. Z uwagi na niską precyzje wyznaczania wartości funkcji, wartości pochodnych znane są jedynie z ograniczoną dokładnością., pochodne zawierają...
-
Downlink Capacity-Coverage Trade-off Estimation Based on Measurement of WCDMA/FDD Interface Load
PublikacjaThe method of capacity-coverage trade-off determination by using of universal load characteristics and normalized coverage curves for the WCDMA/FDD radio interface has been presented. The practical applications of discussed method for UMTS radio network planning process and network exploitation has been mentioned.
-
The estimation of regional oil recovery capacity based on marine oil spill response scenario in Vietnam
Publikacja -
Comparison of Average Energy Slope Estimation Formulas for One-dimensional Steady Gradually Varied Flow
PublikacjaTo find the steady flow water surface profile, it is possible to use Bernoulli’s equation, which is a discrete form of the differential energy equation. Such an approach requires the average energy slope between cross-sections to be estimated. In the literature, many methods are proposed for estimating the average energy slope in this case, such as the arithmetic mean, resulting in the standard step method, the harmonic mean and...
-
Selected properties and parameters of radio channel impulse response estimation in ISM 2.4 GHz band
PublikacjaThe article presents experimental research indicating that the impulse response of the communication channel, determined in practice, are not of an universal character, but only represent its approximate value for the frequency on which this measurement was made. Phases for each of the replicas of the measurement signal were determined during the analysis of the received signals in the baseband. Phase changes of individual replicas...
-
Estimation of time-frequency complex phase-based speech attributes using narrow band filter banks
PublikacjaIn this paper, we present nonlinear estimators of nonstationary and multicomponent signal attributes (parameters, properties) which are instantaneous frequency, spectral (or group) delay, and chirp-rate (also known as instantaneous frequency slope). We estimate all of these distributions in the time-frequency domain using both finite and infinite impulse response (FIR and IIR) narrow band filers for speech analysis. Then, we present...
-
Application of road map of operating condition for estimation of fuel and electric energy consumption from city transport
PublikacjaThe paper presents procedure of data collecting and generation of road map of operating condition in the selected urban area. This map allows forecasting the selected vehicle operating parameters for the assumed road. The main parameters calculated using the road maps of operating conditions are: total energy spent to drive the selected vehicle, consumed fuel, travel time, average speed of travel, CO2 emissions. Presented example...
-
Impact of Geometrical Imperfections on Estimation of Buckling and Limit Loads in a Silo Segment Using the Vibration Correlation Technique
PublikacjaThe paper examines effectiveness of the vibration correlation technique which allows determining the buckling or limit loads by means of measured natural frequencies of structures. A steel silo segment with a corrugated wall, stiffened with cold-formed channel section columns was analysed. The investigations included numerical analyses of: linear buckling, dynamic eigenvalue and geometrically static non-linear problems. Both perfect...
-
Application of the chromatographic retention index system for the estimation of the calibration constants of permeation passive samplers with polydimethylsiloxane membranes
PublikacjaThe paper presents the results of research on the calibration of permeation passive samplers equipped with polydimethylsiloxane (PDMS) membranes using the physico-chemical properties of the analytes. Strong correlations were found between the calibration constants of the samplers and the linear temperature-programmed retention indices of the analytes determined on columns coated with pure PDMS (r2 = 0.914). These correlations...
-
The estimation of cutting forces and specific force coefficients during finishing ball end milling of inclined surfaces
Publikacja -
Minimum mean square error estimation of speech short-term predictor parameters under noisy conditions
Publikacja -
Towards realistic estimation of ship excessive motions in heavy weather. A case study of a containership in the Pacific Ocean
Publikacja -
Maximum contact stress estimation on acetabular surface in total hip replacement using fuzzy reasoning system
PublikacjaArtykuł przedstawia rozmyty system wnioskowania dla oszacowania maksymalnego naprężenia kontaktowego na powierzchni panewki endoprotezy stawu biodrowego. Maksymalne naprężenie kontaktowe zostało określone na podstawie kąta Wiberga oraz masy ciała pacjenta.
-
Zastosowanie metody FMEA w ocenie procesu technologicznego = Application of Fmea method to estimation of technological process
PublikacjaPrzedstawiono wykorzystanie metody FMEA do oceny technologii części klasy tuleja. Szczegółowo omówiono wyniki analizy toczenia kształtującego, operacji hartowania i odpuszczania oraz obróbki wykańczającej przez szlifowanie.
-
A Revised Approach to Flood Damage Estimation in Flood Risk Maps and Flood Risk Management Plans, Poland
Publikacja -
Nuclear Activation Methods in the Estimation of Environmental Pollution and the Assessment of the Industrial Plant Impact on the Citizens of Gdansk (Poland)
PublikacjaNeutronowa Analiza Aktywacyjna została wykorzystana do oceny stanu jakości powietrza atmosferycznego na podstawie badań analitycznych stopnia kumulacji zanieczyszczeń nieorganicznych w mchu torfowca, a także składu wód opadowych. Ponadto przedstawiono wyniki badań dotyczących szacowania ryzyka zawodowego pracowników zakładów przemysłowych na podstawie analizy próbek materiału biologicznego pobranego od osób narażonych.
-
Probability estimation of the city’s energy efficiency improvement as a result of using the phase change materials in heating networks
Publikacja -
Estimation and modeling hydrolysis of slowly biodegradable substrate based on the batch respirometric tests in activated sludge systems
PublikacjaNowadays, appropriate determination of chemical oxygen demand (COD) fractionation together with degradation kinetics of organic compounds have a prime importance on the design and operation of activated sludge systems. Batch respirometric tests based on the oxygen uptake rates (OUR) and corresponding COD is accepted method to reflect the consumption of biodegradable substrates. The influence of the readily biodegradable (Ss) fraction...
-
Estimation of the minimal number of periodic points for smooth self-maps of odd dimensional real projective spaces
PublikacjaLet f be a smooth self-map of a closed connected manifold of dimension m⩾3. The authors introduced in [G. Graff, J. Jezierski, Minimizing the number of periodic points for smooth maps. Non-simply connected case, Topology Appl. 158 (3) (2011) 276-290] the topological invariant NJD_r[f], where r is a fixed natural number, which is equal to the minimal number of r-periodic points in the smooth homotopy class of f. In this paper smooth...
-
Quantitative estimation of volume changes of granular materials during silo flow using X-ray tomography.
PublikacjaW artykule przedstawiono wyniki badań doświadczalnych nad zmianami objętościowymi materiału granulowanego podczas przepływu silosowego. Badania wykonano przy zastosowaniu tomografii rentgenowskiej. Wyniki porównano z wynikami doświadczalnymi przy zastosowaniu cyfrowej obróbki zdjęć płynącego materiału.
-
Analysis of the Water Level Variation in the Polish Part of the Vistula Lagoon (Baltic Sea) and Estimation of Water Inflow and Outflow Transport through the Strait of Baltiysk in the Years 2008–2017
PublikacjaThe Vistula Lagoon is located in both Poland and Russia along the southern coast of the Baltic Sea. It is connected to the Baltic Sea in the Russian part by the Strait of Baltiysk. The purpose of the paper is to identify the dominant factors underlying the water level variation mechanism at Tolkmicko in the Vistula Lagoon, revealed by a statistical analysis of the measured data and a discussion on the inflow and outflow transport...
-
Titania Nanotubes/Hydroxyapatite Nanocomposites Produced with the Use of the Atomic Layer Deposition Technique: Estimation of Bioactivity and Nanomechanical Properties
PublikacjaTitanium dioxide nanotubes/hydroxyapatite nanocomposites were produced on a titanium alloy (Ti6Al4V/TNT/HA) and studied as a biocompatible coating for an implant surface modification. As a novel approach for this type of nanocomposite fabrication, the atomic layer deposition (ALD) method with an extremely low number of cycles was used to enrich titania nanotubes (TNT) with a very thin hydroxyapatite coating. X-ray diffraction (XRD)...
-
Cutting power estimation of the bandsawing process of beech wood (Fagus sylvatica L.) dried in three operating modes
PublikacjaIn this paper the predicted values of cutting power for bandsawing machine (ST100R, f. Stenner), which is located at the sawmill company Complex in Dziemiany, were presented. The values of cutting power were forecasted for beech wood (Fagus sylvatica L.), from the northern part of Pomerania region in Poland, which was dried in three operating modes: BKP - air drying at 25oC, BKS - air-steam mixture drying at 80oC, BKW - steam drying...
-
Empirical Model for Phycocyanin Concentration Estimation as an Indicator of Cyanobacterial Bloom in the Optically Complex Coastal Waters of the Baltic Sea
Publikacja -
<title>Selection of GRNN network parameters for the needs of state vector estimation of maneuvering target in ARPA devices</title>
Publikacja -
A system for Direction-Of-Arrival estimation in ISM 2.4 GHz frequency band based on ESPAR antenna and SDR technology
PublikacjaDetermination of the direction of the signal arrival (DOA) finds many applications in various areas of science and industry. Knowledge of DOA is used, among others to determine the position of a satellite with a low Earth orbit (LEO), localization of people and things as well as in research of wireless communication systems, for instance the determination of the number of...
-
Estimation, optimization and analysis based investigation of the energy consumption in machinability of ceramic-based metal matrix composite materials
Publikacja -
Estimation of Minimum Uncut Chip Thickness during Precision and Micro-Machining Processes of Various Materials—A Critical Review
Publikacja -
Estimation of wastewater treatment plant state for model predictive control of N-P remowal at medium time scale.
PublikacjaPrzy ograniczonych możliwościach pomiarowych estymaty stanu są potrzebne w sterowaniu optymalizującym, opartym na sterowaniu predykcyjnym, sterującym usuwaniem azotu i fosforu, w biologicznej oczyszczalni ścieków. Optymalizator MPC do implementacji sprzężenia zwrotnego z obiektu potrzebuje tych estymat. Dodatkowo aktualizowane muszą być parametry modelu Gray-Box wykorzystywanego w module MPC. Wtedy estymaty stanu są używane przez...
-
Weighted least squares parameter estimation for model predictive control of integrated wastewater systems at medium time scale.
PublikacjaW artykule przedstawione zostało sformułowanie i implementacja algorytmu ważonej sumy najmniejszych kwadratów na przesuwnym oknie pomiarowym dla celów estymacji parametrów modelu typu szara skrzynka. Model typu szara skrzynka dynamiki reaktora biologicznego jest wykorzystywany przez moduł sterowania predykcyjnego sterujący zintegrowanym systemem ściekowym w średniej skali czasu. Algorytm estymacji parametrów był walidowany na symulatorze...
-
Estimation of Potential Leakage from Dumped Chemical Munitions in the Baltic Sea Based on Two Different Modelling Approaches
Publikacja -
Determination of an adequate number of competitive functional models in the square Msplit(q) estimation with the use of a modified Baarda’s approach
Publikacja