wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: stability
-
Surface active fatty acid ILs: Influence of the hydrophobic tail and/or theimidazolium hydroxyl functionalization on aggregates formation
PublikacjaNine structurally-related fatty acid ionic liquids have been prepared and their thermal behavior as well as their ability to self-assemble in water has been investigated. The thermal properties were studied by thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC), while the aggregation behavior was analyzed by tensiometry, isothermal titration calorimetry (ITC), conductometry, dynamic light scattering (DLS),...
-
Application of Extreme Doses of Aluminium for Growth Control of Filmentous Bacteria Microthrix Parvicella in an Activated Sludge System - Laboratory Investigations
PublikacjaLaboratory investigations of aluminium (PAX-16) application for control of population of filamentous bacteria Microthrix Parvicella in a three-phase bioreactor in lab-scale were performed. Dosing of small aluminium doses (approximately 0.5 mgAl/gMLSS·d) in the period preceding seasonal growth of M.Parvicella failed to prevent mass growth of this microorganism leading to activated sludge bulking phenomenon (SVI-250 ml/gMLSS)...
-
Single-step grown boron doped nanocrystalline diamond-carbon nanograss hybrid as an efficient supercapacitor electrode
PublikacjaDirect synthesis of nano-structured carbon hybrid consisting of vertically aligned carbon nanograss on top of boron-doped nanocrystalline diamond is demonstrated and the carbon hybrid is further applied as an electrode material for the fabrication of supercapacitor. The hybrid film combines the dual advantages of sp2 (carbon nanograss) and sp3 (nanocrystalline diamond) bonded carbon, possessing not only the excellent electrical...
-
Respiration rate estimation using non-linear observers in application to wastewater treatment plant
PublikacjaA problem of respiration rate estimation using two new non-linear observers for a wastewater treatment plant is addressed in this paper. In particular, a non-linear adaptive Luenberger-like observer and a super twisting sliding mode observer have been derived to produce stable and bounded estimates of the respiration rate. During the synthesis of the particular observer, an appropriate mathematical utility model was used. The observability...
-
New approach for the synthesis of Ag3PO4-graphene photocatalysts
PublikacjaA facile and effective plasma sputtering method for the preparation of a visible light active photocatalyst - rhombic dodecahedral silver phosphate Ag3PO4 covered with nanographene (Ag3PO4-GR) with improved stability has been developed. Proposed method allows for the usage of readily available materials for nanographene sputtering and for easy scaling-up. The stability improvement, confirmed by visible light-induced phenol degradation...
-
A Fortran-95 algorithm to solve the three-dimensional Higgs boson equation in the de Sitter space-time
Dane BadawczeA numerically efficient finite-difference technique for the solution of a fractional extension of the Higgs boson equation in the de Sitter space-time is designed. The model under investigation is a multidimensional equation with Riesz fractional derivatives of orders in (0,1)U(1,2], which considers a generalized potential and a time-dependent diffusion...
-
Investigation on domestic fruits seed oils in personal care emulsion systems
PublikacjaThe use of fruit seed oils in personal care products is of significance to both their function and image. Poland is an important processor of fruit products within the EU, and thus has a large availability of seeds from domestic fruits, which are normally considered to be a waste material. Unfortunately, current literature is scarce of the suitability of these oils for topical use in the form of cosmetic emulsions. Published data...
-
Forced Degradation Studies of Ivabradine and In Silico Toxicology Predictions for Its New Designated Impurities
PublikacjaAll activities should aim to eliminate genotoxic impurities and/or protect the API against degradation. There is a necessity to monitor impurities from all classification groups, hence ivabradine forced degradation studies were performed. Ivabradine was proved to be quite durable active substance, but still new and with insufficient stability data. Increased temperature, acid, base, oxidation reagents and light were found to cause...
-
Modeling the debonding process of osseointegrated implants due to coupled adhesion and friction
PublikacjaCementless implants have become widely used for total hip replacement surgery. The long-term stability of these implants is achieved by bone growing around and into the rough surface of the implant, a process called osseointegration. However, debonding of the bone–implant interface can still occur due to aseptic implant loosening and insufficient osseointegration, which may have dramatic consequences. The aim of this work is to...
-
Problematyka dotycząca zapewnienia fotostabilności substancji leczniczych w postaciach leku
PublikacjaUV and visible radiation may influence on the stability of some active pharmaceutical ingredients and in a consequence destabilizes such medicinal products, causes changesin its physicochemical properties also with negative pharmacological and sometimes even toxic effects. For this reason it is important to conduct the routine testing photostability. The knowledge of chemistry and technology as well as some methods of...
-
Recurrent potential pulse technique for improvement of glucose sensing ability of 3D polypyrrole
PublikacjaIn this work, a new approach for using a 3D polypyrrole (PPy) conducting polymer as a sensing material for glucose detection is proposed. Polypyrrole is electrochemically polymerized on a platinum screen-printed electrode in an aqueous solution of lithium perchlorate and pyrrole. PPy exhibits a high electroactive surface area and high electrochemical stability, which results in it having excellent electrocatalytic properties. The...
-
Accuracy Analysis of Determination the Vertical Displacements in Unstable Reference System
PublikacjaMeasurements of horizontal and vertical displacements are carried out mostly based on reference points identified as fixed. In surveying practice there may be some situations in which there is not possible to perform the measurements with reference to stable points or the difficulties in identification of points’ stability may arise. Accuracy analysis based on the covariance matrices have a special role in this process. In presented...
-
Protein thermal stabilization in aqueous solutions of osmolytes
PublikacjaProteins’ thermal stabilization is a significant problem in various biomedical, biotechnological, and technological applications. We investigated thermal stability of hen egg white lysozyme in aqueous solutions of the following stabilizing osmolytes: Glycine (GLY), N-methylglycine (NMG), N,N-dimethylglycine (DMG), N,N,N-trimethylglycine (TMG), and trimethyl-N-oxide (TMAO). Results of CD-UV spectroscopic investigation were compared...
-
Inverse shadowing and related measures
PublikacjaWe study various weaker forms of the inverse shadowing property for discrete dynamical systems on a smooth compact manifold. First, we introduce the so-called ergodic inverse shadowing property (Birkhoff averages of continuous functions along an exact trajectory and the approximating one are close). We demonstrate that this property implies the continuity of the set of invariant measures in the Hausdorff metric. We show that the...
-
A hierarchical observer for a non-linear uncertain CSTR model of biochemical processes
PublikacjaThe problem of estimation of unmeasured state variables and unknown reaction kinetic functions for selected biochemical processes modelled as a continuous stirred tank reactor is addressed in this paper. In particular, a new hierarchical (sequential) state observer is derived to generate stable and robust estimates of the state variables and kinetic functions. The developed hierarchical observer uses an adjusted asymptotic observer...
-
Synthesis and properties of porous Sr 0.96 Y 0.04 Ti 1−x Nb x O 3
PublikacjaA series of porous, single phase Sr0.96Y0.04Ti1-xNbxO3 samples was obtained using a wet synthesis method (modified citrate sol-gel) method. Temperature-programmed reduction (TPR) and temperature-programmed oxidation (TPO) measurements have shown high stability of the obtained material in variable (oxidizing/reducing) atmospheres. All samples exhibit high conductivity in hydrogen atmosphere with the highest value (around 1S/cm)...
-
The influence of synthesis method on the microstructure and catalytic performance of Y 0.07 Sr 0.93 Ti 0.8 Fe 0.2 O 3-δ in synthetic biogas operated solid oxide fuel cells
PublikacjaThe Y0.07Sr0.93Ti0.8Fe0.2O3-δ (YSTF) material was fabricated using three different synthesis methods: modified polymer precursor method (MPP), Pechini method and a solid state reaction method. It was applied as an anode catalytic material for biogas reforming in solid oxide fuel cells. Clear differences in the microstructure of fabricated catalytic layers were found, mainly with respect to a grain size and distribution of grains....
-
Long-term hindcast simulation of currents in the Baltic Sea
Dane BadawczeThe dataset contains the results of numerical modelling of currents over a period of 50 years (1958-2007) in the Baltic Sea . A long-term hindcast simulation was performed using a three-dimensional hydrodynamic model PM3D (Kowalewski and Kowalewska-Kalkowska, 2017), a new version of the M3D model (Kowalewski, 1997). The hydrodynamic model was coupled...
-
Catalytic Activity of Nickel and Ruthenium–Nickel Catalysts Supported on SiO2, ZrO2, Al2O3, and MgAl2O4 in a Dry Reforming Process
PublikacjaDry reforming of methane (DRM) is an eco-friendly method of syngas production due to the utilization of two main greenhouse gases—methane and carbon dioxide. An industrial application of methane dry reforming requires the use of a catalyst with high activity, stability over a long time, and the ability to catalyze a reaction, leading to the needed a hydrogen/carbon monoxide ratio. Thus, the aim of the study was to investigate the...
-
Mater-Bi/Brewers’ Spent Grain Biocomposites—Novel Approach to Plant-Based Waste Filler Treatment by Highly Efficient Thermomechanical and Chemical Methods
PublikacjaThermoplastic starch (TPS) is a homogenous material prepared from native starch and water or other plasticizers subjected to mixing at a temperature exceeding starch gelatinization temperature. It shows major drawbacks like high moisture sensitivity, poor mechanical properties, and thermal stability. To overcome these drawbacks without significant cost increase, TPS could be blended with bio-based or biodegradable polymers and...
-
Computational analysis of substituent effects on proton affinity and gas-phase basicity of TEMPO derivatives and their hydrogen bonding interactions with water molecules
PublikacjaThe study investigates the molecular structure of 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO) and its derivatives in the gas phase using B3LYP and M06-2X functional methods. Intermolecular interactions are analyzed using natural bond orbital (NBO) and atoms in molecules (AIM) techniques. NO2-substituted TEMPO displays high reactivity, less stability, and softer properties. The study reveals that the stability of TEMPO derivatives...
-
Thermal Instability of Choline Chloride-Based Deep Eutectic Solvents and Its Influence on Their Toxicity─Important Limitations of DESs as Sustainable Materials
PublikacjaDeep eutectic solvents (DESs) have become a hot topic in many branches of science due to their remarkable properties. They have been studied in a wide variety of applications. In particular, choline chloride (ChCl)-based DESs are one of the most commonly used representatives of these fluids. Nevertheless, in order to apply DESs in some fields, it is essential to guarantee their stability, reusability, and biocompatibility. In this...
-
Mechanism of Reduced Sintering Temperature of Al2O3–ZrO2 Nanocomposites Obtained by Microwave Hydrothermal Synthesis
PublikacjaA novel method to obtain Al2O3–ZrO2 nanocomposites is presented. It consists of the co-precipitation step of boehmite (AlO(OH)) and ZrO2, followed by microwave hydrothermal treatment at 270 ◦ C and 60 MPa, and by calcination at 600 ◦ C. Using this method, we obtained two nanocomposites: Al2O3–20 wt % ZrO2 and Al2O3–40 wt % ZrO2. Nanocomposites were characterized by Fourier transformed infrared spectroscopy, Raman spectroscopy,...
-
Sustainable upcycling of brewers’ spent grain by thermo-mechanical treatment in twin-screw extruder
PublikacjaThermo-mechanical treatment of brewers’ spent grain (a by-product of beer manufacturing) was successfully performed via the extrusion process. The impact of temperature (from 30 to 180 °C), throughput (from 1 to 5 kg/h) and screw speed (from 75 to 375 rpm) on particle size, color, chemical structure, antioxidant activity and thermal stability of resulting material, as well as correlations between particular properties, were investigated....
-
Thermal ablation modeling via bioheat equation
PublikacjaWe consider Pennes’ bioheat equation and discuss an implicit numerical scheme which has better stability properties than other approaches. Our discussion concerns Carthesian geometry problems, however it carries over to spherical geometry models and more complicated shapes.
-
Reply to Comment on ‘Nanodiamond incorporated human liver mimicking phantoms: prospective calibration medium of magnetic resonance imaging’
PublikacjaDependence of the spin–lattice (T1) relaxation times on the nanodiamond concentration in human liver phantoms is discussed. Factors affecting stability and and reproducibility of these phantoms are presented. The need for comparative measurements on multiple MRI scanners for better understanding of potential variations in the obtained imaging data is emphasised.
-
Badania wytrzymałościowe zgrzein łączących pręty zbrojeniowe o średnicy Ø30mm
PublikacjaZakres badań dotyczy oceny wytrzymałościowej zgrzein doczołowych, wykonanych metodą zwarciową. Elementami zgrzewanymi były pręty zbrojeniowe o średnicy Ø30mm. Badania związane są z okresową kontrolą stabilności parametrów zgrzewarki, szczególnie w odniesieniu do górnych, dopuszczalnych przez producenta zakresów parametrów zgrzewania oraz analizą wyników i porównaniu rezultatów prób wytrzymałościowych uzyskanych w 2019 i 2020 w...
-
Wykorzystanie algorytmów ewolucyjnych do doboru wzmocnień rozszerzonego obserwatora prędkości maszyny indukcyjnej
PublikacjaW pracy opisano sposób doboru wzmocnień rozszerzonego obserwatora prędkości maszyny indukcyjnej przy wykorzystaniu algorytmów ewolucyjnych. Zaproponowano funkcję celu opartą na rozkładzie biegunów obserwatora. Ze względu na wpływ prędkości maszyny na dynamikę obserwatora zaproponowano dobór wzmocnień obserwatora dla różnych przedziałów prędkości. Dla poszczególnych przedziałów zaprezentowano wyniki doboru wzmocnień w postaci tabel...
-
Badania stabilności chemicznej kompozytowego elektrolitu 3-YSZ-Al2O3 w stosunku do materiałów elektrodowych do zastosowania w średniotemperaturowych ogniwach paliwowych
PublikacjaJednym z podstawowych wymogów stawianych mate- riałom na elektrolity do średniotemperaturowych ogniw paliwowych IT-SOFC (ang. intermediate-temperature solid oxide fuel cells) jest ich kompatybilność chemiczna z elektrodami w temperaturach zarówno eksploatacji, jak i wytwarzania ogniw. W celu sprawdzenia, czy badany w pracy kompozytowy elektrolit o osnowie z częściowo stabilizowanego ditlenku cyrkonu i z wtrąceniami tlenku glinu...
-
Running performance of an aerodynamic journal bearing with squeeze film effect
PublikacjaResults of theoretical and experimental studies concerning the performance of an aerodynamic journal bearing of which running is assisted by squeeze film ultrasonic levitation (SFUL) are presented in this paper. The SFUL mechanism not only can separate journal from the bearing at the start and stop phases of operation but also can significantly contribute to the dynamic stability of the bearing when it runs at speed. Computer calculations...
-
Morphology and the physical and thermal properties of thermoplastic polyurethane reinforced with thermally reduced graphene oxide
PublikacjaIn this study, thermally reduced graphene oxide (TRG)-containing polyurethane nanocomposites were obtained by the extrusion method. The content of TRG incorporated into polyurethane elastomer systems equaled 0.5, 1.0, 2.0 and 3.0 wt%. The morphology, static and dynamic mechanical properties, and thermal stability of the modified materials were investigated. The application of TRG resulted in a visible increase in material stiffness...
-
Effect of Axial Porosities on Flexomagnetic Response of In-Plane Compressed Piezomagnetic Nanobeams
PublikacjaWe investigated the stability of an axially loaded Euler–Bernoulli porous nanobeam considering the flexomagnetic material properties. The flexomagneticity relates to the magnetization with strain gradients. Here we assume both piezomagnetic and flexomagnetic phenomena are coupled simultaneously with elastic relations in an inverse magnetization. Similar to flexoelectricity, the flexomagneticity is a size-dependent property. Therefore,...
-
Modification of microporous polyurethane elastomers with different types of ash—morphological, mechanical, and thermal studies
PublikacjaIncorporation of wood ash particles from wood gasification into microporous polyurethane elastomers has been investigated and compared to addition of commercially available microspheres resulting from coal burning. Samples were modified with 3 and 6 wt% of fillers. Structure, mechanical, and thermal properties of obtained elastomers were investigated. Incorporation of both types of ash particles decreased the density of polyurethanes...
-
Crank–Nicolson FDTD Method in Media Described by Time-Fractional Constitutive Relations
PublikacjaIn this contribution, we present the Crank-Nicolson finite-difference time-domain (CN-FDTD) method, implemented for simulations of wave propagation in media described by time-fractional (TF) constitutive relations. That is, the considered constitutive relations involve fractional-order (FO) derivatives based on the Grünwald-Letnikov definition, allowing for description of hereditary properties and memory effects of media and processes....
-
A dual-control strategy based on electrode material and electrolyte optimization to construct an asymmetric supercapacitor with high energy density
PublikacjaMetal-organic frames (MOFs) are regarded as excellent candidates for supercapacitors that have attracted much attention because of their diversity, adjustability and porosity. However, both poor structural stability in aqueous alkaline electrolytes and the low electrical conductivity of MOF materials constrain their practical implementation in supercapacitors. In this study, bimetallic CoNi-MOF were synthesized to enhance the electrical...
-
On the plastic buckling of curved carbon nanotubes
PublikacjaThis research, for the first time, predicts theoretically static stability response of a curved carbon nanotube (CCNT) under an elastoplastic behavior with several boundary conditions. The CCNT is exposed to axial compressive loads. The equilibrium equations are extracted regarding the Euler–Bernoulli displacement field by means of the principle of minimizing total potential energy. The elastoplastic stress-strain is concerned...
-
Fluorescence of nanodiamond cocktails: pH-induced effects through interactions with comestible liquids
PublikacjaFluorescent nanodiamonds with nitrogen-vacancy centers have become important nanoscale probes for sensing and imaging. The surface chemistry of the nanodiamonds influences their emission, interactions, and quantum properties. In this work, we propose to utilize fluorescent nanodiamonds as photostable markers for investigation of comestible liquids. We prepared nanodiamond/comestibles suspensions/cocktails with a wide range of pH...
-
Understanding the capacitance of thin composite films based on conducting polymer and carbon nanostructures in aqueous electrolytes
PublikacjaIn this work electrochemical performance of thin composite films consisted of poly(3,4-ethylenedioxythiophene) (PEDOT), graphene oxide (GOx) and oxidized multiwalled carbon nanotubes (oxMWCNTs) is investigated in various sulphates (Li2SO4, Na2SO4, K2SO4, MgSO4) and acidic (H2SO4) electrolytes. Capacitance values, rate capability and cycling stability achieved for the composite layers are correlated with the electrolytes’ properties...
-
Thermal ablation modeling via the bioheat equation and its numerical treatment
PublikacjaThe phenomenon of thermal ablation is described by Pennes’ bioheat equation. This model is based on Newton’s law of cooling. Many approximate methods have been considered because of the importance of this issue. We propose an implicit numerical scheme which has better stability properties than other approaches.
-
Experimental investigation of joint with positive eccentricity in CFS truss
PublikacjaDue to technological restrictions, in the case of trusses made of CFS open cross-sections, positive eccentricities in the truss joints have become very frequent. Therefore studies concerning the load-bearing capacity of truss joints with positive eccentricity were undertaken. It was assumed that the resistance of cold-formed steel (CFS) open cross-section truss joints located on compression chords and with positive eccentricity...
-
ANALYSIS OF THE p53 PROTEIN GENE EXPRESSION MODEL
PublikacjaWe study the asymptotic behaviour of the solutions of the p53-Mdm2 model proposed by Monk (2003). The p53 gene is crucial for cellular inhibition of the angiogenesis process, while Mdm2 is a negative regulator of the p53 tumor-suppressor. We investigate the stability of the positive steady state and perform some numerical experiments.
-
Mieszanie w klasie niejednorodnych łańcuchów Markowa i kwadratowych operatorów stochastycznych
PublikacjaRozprawa doktorska poświęcona jest zagadnieniu asymptotycznych własności w klasie nieskończenie wymiarowych niejednorodnych łańcuchów Markowa z czasem dyskretnym oraz w klasie kwadratowych operatorów stochastycznych. W pierwszej kolejności definiowane są różne rodzaje asymptotycznego zachowania (mieszania) niejednorodnych łańcuchów Markowa odpowiadające zbieżności w normowej i mocnej topologii operatorowej oraz omówione są relacje...
-
Coordination complexes of Mn(II), Co(II), Ni(II), Zn(II) and Cd(II) with histaminol – Crystal structures and formation constants in aqueous solution
PublikacjaStability constants were determined for a series of coordination complexes of Mn(II), Co(II), Ni(II), Zn(II) and Cd(II) with histaminol in aqueous solution. The tendency of histaminol to form chelate complexes has been confirmed by the isolation of several complex species in the monocrystalline form and determination of their molecular structures.
-
Difference functional inequalities and applications.
PublikacjaThe paper deals with the difference inequalities generated by initial boundary value problems for hyperbolic nonlinear differential functional systems. We apply this result to investigate the stability of constructed difference schemes. The proof of the convergence of the difference method is based on the comparison technique, and the result for difference functional inequalities is used. Numerical examples are presented.
-
Genetic Algorithm Approach for Gains Selection of Induction Machine Extended Speed Observer
PublikacjaThe subject of this paper is gains selection of an extended induction machine speed observer. A high number of gains makes manual gains selection difficult and due to nonlinear equations of the observer, well-known methods of gains selection for linear systems cannot be applied. A method based on genetic algorithms has been proposed instead. Such an approach requires multiple fitness function calls; therefore, using a quality index...
-
Przydatność urządzenia zmechanizowanego do wyznaczania trwałości ściernic do przecinania ręcznego
PublikacjaW artykule przedstawiono porównawcze wyniki badań trwałości ściernic do przecinania ręcznego, zużywanych na dwóch urządzeniach: z całkowicie ręcznym prowadzeniem przez operatora narzędzia i na urządzeniu zautomatyzowanym symulującym warunki przecinania ręcznego ściernicą. Wykazano, że dla tych dwóch urządzeń nie ma istotnej statystycznie korelacji pomiędzy wartościami wskaźnika wydajności względnej GA, reprezentującego trwałość...
-
Elastic polyurethane foams containing graphene nanoplatelets
PublikacjaElastic polyurethane foams were produced from two-component polyurethane systems (SPECFLEX NE 113 izocyjanian/NR 816 poliol system—SPC and Elastic MBMarket company system POLYOL ET MB 500/ISO ET MB 800—ET) by using a one-step method. The foams were a graphene nanoplatelets (GNP) in the amount ranging from 1 to 2 wt.%. The effect of the nanofiller on polyurethane matrix was determined by analyzing the chemical structure, static...
-
Investigation of catalytic layers on anode for solid oxide fuel cells operating with synthetic biogas
PublikacjaIn this paper solid oxide fuel cells operating with dry synthetic biogas have been examined. In order to increase their stability the layers of CuO-CeO2, Cu1.3Mn1.7O4 and Y0.08Sr0.92Ti0.8Fe0.2O3 -δ have been deposited on the Ni-YSZ anode site. These layers should catalyze the internal biogas reforming and prevent the carbon deposition on the anode site. It has been found that CuO-CeO2 and Cu1.3Mn1.7O4 catalysts led to an increase...
-
Chitin and derivative chitosan-based structures — Preparation strategies aided by deep eutectic solvents: A review
PublikacjaThe high molecular weight of chitin, as a biopolymer, challenges its extraction due to its insolubility in the solvents. Also, chitosan, as the N-deacetylated form of chitin, can be employed as a primary material for different industries. The low mechanical stability and poor plasticity of chitosan films, as a result of incompatible interaction between chitosan and the used solvent, have limited its industrialization. Deep eutectic...
-
Analytical Estimation of Power Losses in a Dual Active Bridge Converter Controlled with a Single-Phase Shift Switching Scheme
PublikacjaMicro-grid solutions around the world rely on the operation of DC/DC power conver- sion systems. The most commonly used solution for these topologies is the use of a dual active bridge (DAB) converter. Increasing the efficiency and reliability of this system contributes to the improvement in the stability of the entire microgrid. This paper discussed an analytical method of energy efficiency and power loss estimation in a single...