Wyszukiwarka
Wyniki wyszukiwania dla: HYDRAULIC TRANSMISSION, PISTON PUMP, EFFICIENCY.
-
Experimental investigation on straight and u-bend double tube heat exchanger with active and passive enhancement methods
PublikacjaAuthors in this work want to demonstrate the possibility to increase the heat transfer efficiency by using simple wire coil inserts to create turbulent flow in the boundary layer as well as air blowing into the annulus of the pipe. In the study, Wilson plot approach was applied in order to estimate heat transfer coefficients for all heat exchanger (HX) configurations. The study focuses on experimental values of heat transfer coefficient...
-
Subjective and Objective Quality Evaluation Study of BPL -PLC Wired Medium
PublikacjaThis paper presents results of research on the effectiveness of bi-directional voice transmission in a 6 kV mine cable network using BPL-PLC (Broadband over Power Line - Power Line Communication) technology. It concerns both emergency cable state (supply outage with cable shorted at both ends) and loaded with distorted current waveforms. The narrowband (0.5 MHz–15 MHz) and broadband (two different modes, frequency range of 3 MHz–7.5...
-
Application of H2O2 to optimize ammonium removal from domestic wastewater
PublikacjaThe paper presents the results of application of hydrogen peroxide (H2O2) for the optimization of the effects of ammonia nitrogen removal from domestic wastewater. The investigations were carried out at a model wastewater treatment plant consisting of a preliminary sedimentation tank and a sand filter with a horizontal flow of wastewater at a constant hydraulic load of 1.44 L/day. The efficiency of ammonia nitrogen removal was...
-
Parametric study of fluid flow and heat transfer over louvered fins of air heat pump evaporator
PublikacjaTwo-dimensional numerical investigations of the fluid flow and heat transfer have been carried out for the laminar flow of the louvered fin-plate heat exchanger, designed to work as an air-source heat pump evap- orator. The transferred heat and the pressure drop predicted by simulation have been compared with the corresponding experimental data taken from the literature. Two dimensional analyses of the louvered fins with varying...
-
Ukrainian Market of Electrical Energy: Reforming, Financing, Innovative Investment, Efficiency Analysis, and Audit
PublikacjaThe aim of this research is to determine the influence of electrical energy market regulation reform in Ukraine on the competitive environment, the reproduction processes of financial and innovative support, and the energy efficiency of the national economy. The authors have put forward and verified the hypothesis that, under conditions of institutional maturity of the Ukrainian electrical energy market, its liberalization and...
-
Numerical analysis of high temperature minichannels heat exchanger performance
PublikacjaNowadays, the most difficult technological challenge in energy sector is connected with the gas micro-CHP units, dedicated to the distributed power generation. They are expected to be of high efficiency and at the same time of compact in size. Regarding the first reason, significant increase in microturbine efficiency can only be achieved by increase in the engine operating temperature. Therefore, one of the critical elements in...
-
Can Communication Power of Separable Correlations Exceed That of Entanglement Resource?
PublikacjaThe scenario of remote state preparation with a shared correlated quantum state and one bit of forward communication [B. Dakić et al., Nat. Phys. 8, 666 (2012)] is considered. Optimization of the transmission efficiency is extended to include general encoding and decoding strategies. The importance of the use of linear fidelity is recognized. It is shown that separable states cannot exceed the efficiency of entangled states by...
-
Integracja bezprzewodowych heterogenicznych sieci IP dla poprawy efektywności transmisji danych na morzu
PublikacjaWraz ze wzrostem istotności środowiska morskiego w naszym codziennym życiu np. w postaci zwiększonego wolumenu transportu realizowanego drogą morską. czy zintensyfikowanych prac dotyczących obserwacji i monitoringu środowiska morskiego, wzrasta również potrzeba opracowania efektywnych systemów komunikacyjnych dedykowanych dla tego środowiska. Heterogeniczne systemy łączności bezprzewodowej integrowane na poziomie warstwy sieciowej...
-
Properties of an innovative multi-functional finish for the improvement of indoor air quality
PublikacjaDue to lifestyle changes, people spend most of their time indoors at present; thus, Indoor Air Quality (IAQ) is a matter of utmost importance. Multi-functional and innovative finishes can help to passively improve the IAQ, benefitting the health and comfort of occupants. For this study, reference and pre-mixed commercial mortars are compared to a new multi-functional hydraulic lime mortar for indoor finishes, in which conventional...
-
Landfill leachate treatment at a pilot plant using hydrophyte systems
PublikacjaConstructed wetlands can provide an effective and economical solution to landfill leachate treatment. In the article the performance of a CW for leachate treatment, consisting of two horizontal flow constructed wetlands (HF-CW) beds, working at the municipal landfill in Gdansk-Szadolki in the period 2004-2005 is being discussed. The plant has been operating since 2001. Clogging problems and surface flow occurred in the system...
-
A CONCEPT DESIGN OF DIESEL – HYDRAULIC PROPULSION SYSTEM FOR PASSENGER SHIP INTENDED FOR INLAND SHALLOW WATER NAVIGATION
PublikacjaThis paper presents an analysis of environmental and technical conditions necessary for working out a possibly most favourable propulsion system for a two – segment passenger ship intended for navigation between Berlin and Kaliningrad. There are presented various types of propulsion systems for small ships as well as analyzed their possible applications and consequences. In this work there were taken into account system’s reliability,...
-
EVALUATION OF THE USE OF M2M-TYPE NB-IoT AND LTE TECHNOLOGIES FOR MARITIME COMMUNICATION SYSTEMS
PublikacjaThe development of IoT (the Internet of Things) wireless transmission opens a new era in communication systems. In the next years, the development and implementation of IoT systems will be very dynamic. It can be seen that the solutions of LTE – NB-IoT (Long Term Evolution – Narrowband IoT) transmission devices are implemented in a wide range of terrestrial solutions, e.g. smart grids. This paper aims to analyse the possibility...
-
Pathways of nitrogen compounds depletion in hybrid constructed wetlands
PublikacjaHybrid Constructed Wetlands are composed of two or more filters with mixed flow direction of sewage. Apparently in the HCWS the benefits of both types of bed are merged, resulting in better effluent quality (organic and nitrogen componds removal). Such heterogeneous environment creates possibilities for different ways of nitrogen "disappearing". The objective of the present study was to compare the removal of nitrogen with accompanying...
-
Sensorless Fault Detection of Induction Motor with Inverter Output Filter
PublikacjaThe paper presents the problem of monitoring and fault detection of a sensorless voltage inverter fed squirrel cage induction motor with LC filter. The detection is based on load torque estimation of the investigated torque transmission system. The load torque is calculated besides the computation of other variables that are mandatory for sensorless drive operation such as rotor flux and speed. The implemented LC filter smooths...
-
Vehicle Dynamics - L-15/C-15/L-15/P-15, Design and Production Engineering, WIMiO, undergraduate studies, engineering studies, full-time (stationary) studies, 2021/2022, se06, (M:320383W0), summer semester 2023/2024
Kursy OnlineModuł przedmiotów wybieralnych, MiBM, I stopień, specjalność w j. angielskim: Design and Production Engineering (DaPE), semestr 6?, (przedmiot dla Chińczyków), Lecture: Throttle by tyred wheel: slip rolling, rolling with tyre strain, vertical and lateral surface reactions, traction, energetic looses, forces in contact path. Drugs of movement: rolling, air, gradient, inertia, cornering and towing. Forces ant torques acting to vehicle...
-
Automatic tuning of a resonant circuit in wireless power supply systems for biomedical sensors
PublikacjaIn this paper, a tuning method of a resonant circuit suited for wireless powering of miniature endoscopic capsules is presented and discussed. The method allows for an automatic tuning of the resonant frequency and matching impedance of a full wave rectifier loading the resonant circuit. Thereby, the receiver tunes so as to obtain the highest power efficiency under given conditions of transmission. A prototype receiver for wireless...
-
Determination of the Theoretical and Actual Working Volume of a Hydraulic Motor—Part II (The Method Based on the Characteristics of Effective Absorbency of the Motor)
Publikacja: In this article, the second method of determination of the theoretical and actual working volume of a hydraulic motor is described. The proposed new method is based on the characteristics of effective absorbency of the motor. The effective absorbency has been defined as the ratio of flow rate in a motor to the rotational speed of the motor’s shaft. It has been shown that the effective absorbency is a nonlinear function of the...
-
PAYMENT TRANSACTIONS’ ENERGY EFFICIENCY
PublikacjaThe payment system and infrastructure is a sector that is not given enough attention today in the context of energy efficiency. This sector plays a big role in organizing and ensuring money circulation and funds. It has its value consisting on the one hand of the cost of payment equipment, infrastructure, payment instruments. On other hand, its value consists of the cost of energy for their manufacture and maintenance. The European...
-
Application of subsurface vertical flow constructed wetlands to reject water treatment in dairy wastewater treatment plant
PublikacjaThe paper presents the effects of applying subsurface vertical flow constructed wetlands (SS VF) for the treatment of reject water generated in the process of aerobic sewage sludge stabilization in the biggest dairy wastewater treatment plant (WWTP) in Poland. Two SS VF beds were built: bed (A) with 0.65 m depth and bed (B) with 1.0 m depth, planted with reeds. Beds were fed with reject water with hydraulic load of 0.1 m d-1 in...
-
Starter for Voltage Boost Converter to Harvest Thermoelectric Energy for Body-Worn Sensors
PublikacjaThis paper examines the suitability of selected configurations of ultra-low voltage (ULV) oscilla-tors as starters for a voltage boost converter to harvest energy from a thermoelectric generator (TEG). Important properties of particularly promising configurations, suitable for on-chip imple-mentation are compared. On this basis, an improved oscillator with a low startup voltage and a high output voltage swing is proposed. The applicability...
-
Logistics of Transnational Corporations as the Basis of Cooperation Between Ukraine and EU (for Poland Example)
PublikacjaThe article describes the scientific and theoretical basis for the organization of logistics management of modern international corporations, owning by assets in mining and metallurgical business in Ukraine and Poland; it had been analyzed the influence of transfer pricing mechanism as one of the main factors affecting on the efficiency of the organization of supply chain of resources (Ukrainian semi-finished goods) to ensure uninterrupted...
-
Accuracy of Differential Phase Delay Estimation for GPS Spoofing Detection
PublikacjaGPS spoofing is an attack based on transmission of false signals to target receivers, in order to force the computation of incorrect time, position or velocity information. It is a threat which is recently considered with continuously growing awareness. There is a need for effective way of GPS spoofing detection. Many groups of methods are proposed in the literature. Spatial processing methods are considered to be robust in a wide...
-
Providing Differentiated Levels of Service Availability in VANET Communications
PublikacjaInter-vehicle communications seems to be a promising remedy not only for a number of road-safety issues, but also to improve the efficiency of road traffic, as well as to support the on-board infotainment applications. However, it often encounters disruptions due to high mobility of vehicles causing frequent failures of communication links. In this paper, we utilize the idea of multipath vehicle-to-vehicle routing to provide protection...
-
High-Power Jamming Attack Mitigation Techniques in Spectrally-Spatially Flexible Optical Networks
PublikacjaThis work presents efficient connection provisioning techniques mitigating high-power jamming attacks in spectrally-spatially flexible optical networks (SS-FONs) utilizing multicore fibers. High-power jamming attacks are modeled based on their impact on the lightpaths’ quality of transmission (QoT) through inter-core crosstalk. Based on a desired threshold on a lightpath’s QoT, the modulation format used, the length of the path,...
-
Konzepte zur Energieeffizienzsteigerung bei Internet-Zugangsgeräten
PublikacjaThe key issue of this paper is the power management of Internet access devices. The paper commences with an outline on the energy consumption of today's IT devices. It is followed by a description of options to increase energy efficiency of computers. The paper proves that in practice network cards and other IT network components, such as modems, network access points, switches and routers have the maximum energy consumption -...
-
DESIGN ANALYSIS OF HYBRID GAS TURBINE - FUEL CELL POWER PLANT IN STATIONARY AND MARINE APPLICATIONS
PublikacjaThe paper concerns design analysis of a hybrid gas turbine power plant with a fuel cell (stack). The aim of this work was to find the most favorable variant of the medium capacity (approximately 50 MW) hybrid system. In the article, computational analysis of two variants of such a system was carried out. The analysis let to calculate capacity, efficiency of both variants and other parameters like flu gas temperature. The paper...
-
Applicability of arrays of microjets heat transfer correlations to design compact heat exchangers
PublikacjaThe article presents experimental studies on a compact heat exchanger with heat transfer intensification by means of impinging microjets. The pursuit to provide high performance of heat exchangers is a response to the demand both in economics and in the universal tendency to miniaturization of industrial equipment. This paper presents the design and tests of a prototype, microjet heat exchanger. The modular design of the heat exchanger...
-
Detection and removal of priority substances and emerging pollutants from stormwater: case study of the Kołobrzeska collector, Gdańsk, Poland
PublikacjaProgressive urban development affects environmental balance and disrupts the hydrologic cycle, in which rainfall plays a significant role. Since rainwater is considered a valuable resource of the environment, many technical solutions are implemented that enable effective rainwater management. On the other hand, stormwater runoff from urban areas contains numerous (also toxic) substances, and therefore should be properly treated....
-
Power Converter Solutions for Industrial PV Applications—A Review
Publikacja: As the use of photovoltaics becomes more widespread, new technologies for more efficient energy generation, transmission, and distribution based on power electronics converters are being developed. The most common applications are grid-on, energy storage, hybrid, and high voltage gain applications. These applications impose several additional requirements in the design of power converters associated with the solar battery’s maximum...
-
The Latest Advances in Wireless Communication in Aviation, Wind Turbines and Bridges
PublikacjaPresent-day technologies used in SHM (Structural Health Monitoring) systems in many implementations are based on wireless sensor networks (WSN). In the context of the continuous development of these systems, the costs of the elements that form the monitoring system are decreasing. In this situation, the challenge is to select the optimal number of sensors and the network architecture, depending on the wireless system’s other parameters...
-
Bariery stosowania technologii odzysku energii w transporcie szynowym
PublikacjaNa wstępie artykułu został przedstawiony przegląd istniejących technologii odzysku energii w procesie hamowania oraz możliwości jej wykorzystania. Omówiono możliwości akumulowania rekuperowanej energii w zasobnikach stacjonarnych oraz tych zainstalowanych w pojazdach, możliwość przesyłu energii do krajowej sieci energetycznej jak również jej bezpośredniego wykorzystania przez inne pojazdy znajdujące się na sieci. W części zasadniczej...
-
Metamaterial-Based Sub-Microwave Electromagnetic Field Energy Harvesting System
PublikacjaThis paper presents the comprehensive analysis of the sub-microwave, radio frequency band resonant metastructures’ electromagnetic properties with a particular emphasis on the possibility of their application in energy harvesting systems. Selected structures based on representative topologies of metamaterials have been implemented in the simulation environment. The models have been analyzed and their substitute average electromagnetic...
-
Pathways of Nitrogen Removal in Hybrid Treatment Wetlands
PublikacjaHybrid Treatment Wetlands (HTWs) are composed of two or more filters with different modes of flow, allowing the benefits of both types of bed to be combined, resulting in better effluent quality (nitrogen and organic compounds removal). Such a heterogeneous environment creates possibilities for different mechanisms of nitrogen removal. The objective of the present study was to investigate the removal of nitrogen versus a range...
-
Liquefaction of alder wood as the source of renewable and sustainable polyols for preparation of polyurethane resins
PublikacjaLiquefaction of wood-based biomass gives different polyol properties depending on the reagents used. In this article, alder wood sawdust was liquefied with glycerol and poly(ethylene glycol) solvents. Liquefaction reactions were carried out at temperatures of 120, 150 and 170 °C. The obtained bio-polyols were analyzed in order to establish the process efficiency, hydroxyl number, acid value, viscosity and structural characteristics...
-
PRELIMINARY RESULTS FROM APPLICATION PHOSLOCK® TO REMOVE PHOSPHORUS COMPOUNDS FROM WASTEWATER
PublikacjaThe aim of the study is to assess the removal effectiveness of phosphorus compoundsby using lanthanum-modified bentonite. This material was produced by the Australian company Phoslock® Water Solutions Pty Ltd. According to the company, Phoslock® has substantial capacity to bound phosphate anions. The investigation was carried out in steady conditions in laboratory model with beakers. The results of the study are related to the...
-
A Low-Profile 3-D Printable Metastructure for Performance Improvement of Aperture Antennas
PublikacjaIn order to increase the radiation performance of aperture-type antennas, this paper demonstrates a low-profile, planar, single-layer, three-dimensional (3-D) printable metastructure. The proposed hybridized metastructure is highly transparent as it is made out of novel hybrid meta-atoms having transmission coefficient magnitudes greater than -0.72 dB and fully complies with the near-field phase transformation principle. The hybridized...
-
Combined Long-Period Fiber Grating and Microcavity In-Line Mach–Zehnder Interferometer for Refractive Index Measurements with Limited Cross-Sensitivity
PublikacjaThis work discusses sensing properties of a long-period grating (LPG) and microcavity in-line Mach–Zehnder interferometer (µIMZI) when both are induced in the same single-mode optical fiber. LPGs were either etched or nanocoated with aluminum oxide (Al2O3) to increase its refractive index (RI) sensitivity up to ≈2000 and 9000 nm/RIU, respectively. The µIMZI was machined using a femtosecond laser as a cylindrical cavity (d = 60...
-
Cellulose Nanofibers Isolated from the Cuscuta Reflexa Plant as a Green Reinforcement of Natural Rubber
PublikacjaIn the present work, we used the steam explosion method for the isolation of cellulose nanofiber (CNF) from Cuscuta reflexa, a parasitic plant commonly seen in Kerala and we evaluated its reinforcing efficiency in natural rubber (NR). Fourier Transform Infrared Spectroscopy (FTIR), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), and Thermogravimetric analysis (TGA) techniques...
-
Intraday price reaction to filing bankruptcy and restructuring proceedings – the evidence from Poland
PublikacjaThis chapter presents the results of research on the price reaction of shares listed on the Warsaw Stock Exchange to filing bankruptcy and/or restructuring applications. Event study was adopted as the research method, and it was performed at 10, 5, and 1-minute intervals. It was found that the reaction is rapid, as it takes 1–2 minutes after the information on bankruptcy and restructuring applications was made public. Significantly...
-
Solar light driven degradation of norfloxacin using as-synthesized Bi 3+ and Fe 2+ co-doped ZnO with the addition of HSO 5 – : Toxicities and degradation pathways investigation
PublikacjaIn this study, solar light responsive Bi3+ and Fe2+ doped ZnO were synthesized and used for photocatalytic degradation of norfloxacin (NOR), an emerging water pollutant. Analysis with Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected area electron...
-
Power Transmission for Millimeter-Wave Indoor/Outdoor Wearable IoT Devices Using Grounded Coplanar Waveguide-Fed On-Body Antenna
PublikacjaThis paper presents for the first-time evaluation of wireless power transmission (WPT) for sustainable low-powered Internet of Things (IoT) devices in realistic indoor/outdoor scenarios using empirical propagation models at 28 GHz. The used empirical propagation models have shown that using an on-body 9×9 mm-wave rectenna array based on a proposed mm-wave antenna is able to charge IoT devices at a distance of 57 m for line-of-sight...
-
Design and experimental investigations of a cylindrical microjet heat exchanger for waste heat recovery systems
PublikacjaCompact heat exchangers have more and more applications in many areas, including the HVAC, food and petrochemical industry. This paper describes the development of heat exchanger technology for waste heat recovery (WHR) from a range of processes. Case-study testing shows that the proposed heat exchanger can successfully enhance heat transfer and recover waste heat in a range of applications making them economically, environmentally and...
-
Energy efficient indoor localisation for narrowband internet of things
PublikacjaThere are an increasing number of Narrow Band IoT devices being manufactured as the technology behind them develops quickly. The high co-channel interference and signal attenuation was seen in edge Narrow Band IoT devices make it challenging to guarantee the service quality of these devices. To maximize the data rate fairness of Narrow Band IoT devices, a multi-dimensional indoor localization model is devised, consisting of...
-
Towards Designing an Innovative Industrial Fan: Developing Regression and Neural Models Based on Remote Mass Measurements
PublikacjaThis article presents the process of the construction and testing a remote, fully autonomous system for measuring the operational parameters of fans. The measurement results obtained made it possible to create and verify mathematical models using linear regression and neural networks. The process was implemented as part of the first stage of an innovative project. The article presents detailed steps of constructing a system to...
-
Selection of circuit geometry for miniaturized microwave components based on concurrent optimization of performance and layout area
PublikacjaThe paper presents a framework for automated EM-driven circuit geometry selection of miniaturized microwave components. Selection of a particular layout is based directly on miniaturization rates achieved for a set of candidate circuit geometries. Size reduction of the considered structures is obtained by replacing their main building blocks (i.e., conventional transmission lines) with slow-wave composite cells and meander lines....
-
Evaluation of Connectivity Gaps Impact on TCP Transmissions in Maritime Communications
PublikacjaMany organizations and research working groups, including among others IEEE, ITU, ETSI and IMO are currently working towards improvements in communication of different types of vehicles (cars, trains, planes and vessels) and upgrading utilities and services offered to their crews and passengers travelling all over the world. The paper deals with selected aspects of the TCP protocol connectivity in maritime wireless networks. The...
-
The effect of PEDOT morphology on hexavalent chromium reduction over 2D TiO2/PEDOT photocatalyst under UV–vis light
PublikacjaThe present study represents an approach to apply organic-inorganic hybrid materials for photocatalytic removal of heavy metals from the aqueous environment. The photocatalytic activity of the semiconductor modified with the conjugated polymer may depends on the conjugated polymer type, its amount and morphology. Therefore, in the present study the effect of poly (3, 4-ethylenedioxythiophene) (PEDOT) morphology on adsorption and photoreduction...
-
SnO2 nanoparticles embedded onto MoS2 nanoflakes - An efficient catalyst for photodegradation of methylene blue and photoreduction of hexavalent chromium
PublikacjaIn this work, a molybdenum disulfide/tin oxide (MoS2/SnO2) composite was successfully prepared via a hydrothermal method. The MoS2/SnO2 composite was used as a photocatalyst for photoreduction of hexavalent chromium and photodecomposition of methylene blue. It exhibited higher photocatalytic performance under simulated solar light irradiation than MoS2 itself. The obtained material was characterized by several spectroscopic and...
-
Mono- and bimetallic (Pt/Cu) titanium(IV) oxide core–shell photocatalysts with UV/Vis light activity and magnetic separability
PublikacjaTitanium(IV) oxide is one of the most widely investigated photocatalysts. However, separation of nano-sized particulate titania might result in profitless technologies for commercial applications. Additionally, bare titania is almost inactive under the Vis range of solar spectrum due to its wide bandgap. Therefore, the present study aims to prepare novel coreinterlayer- shell TiO2 magnetic photocatalysts modified with metal nanoparticles...
-
Various types of semiconductor photocatalysts modified by CdTe QDs and Pt NPs for toluene photooxidation in the gas phase under visible light
PublikacjaA novel synthesis process was used to prepare TiO2 microspheres, TiO2 P-25, SrTiO3 and KTaO3 decorated by CdTe QDs and/or Pt NPs. The effect of semiconductor matrix, presence of CdTe QDs and/or Pt NPs on the semiconductor surface as well as deposition technique of Pt NPs (photodeposition or radiolysis) on the photocatalytic activity were investigated. The as-prepared samples were characterized by X-ray powder diffractometry (XRD),...