Wyszukiwarka
Wyniki wyszukiwania dla: METROLOGY
-
Application of infrared thermoography to non-contact testing of varistors
PublikacjaTesting of varistors using thermography was carried out in order to assess their protective properties against possible overvoltage phenomena in the form of high-level voltage surges. An advantage of the thermography technique is non-contact temperature measurement. It was proposed to assess the properties of varistors workingin electronic devices as protective elements, on the basis of estimating temperature increments on varist...
-
A family of new generation miniaturized impedance analyzers for technical object diagnostics
PublikacjaThe paper presents the family of three analyzers allowing to measure impedance in range of 10 ohm<|Zx|<10 Gohm in a wide frequency range from 10 mHz up to 100 kHz. The most important features of the analyzers family are: miniaturization, low power consumption, low production cost, telemetric controlling and the use of impedance measurement method based on digital signal processing DSP. The miniaturization and other above mentioned...
-
Fast High-Impedance Spectroscopy Method Using SINC Signal Excitation
PublikacjaIn this paper the method of fast impedance spectroscopy of technical objects with high impedance (|Zx| > 1 Gohm) is evaluated by means of simulation and practical experiment. The method is based on excitation of an object with a sinc signal and sampling response signals proportional to current flowing through and voltage across the measured impedance. The object impedance spectrum is obtained with use of continuous Fourier transform...
-
Laser reflectance interferometry system with a 405 nm laser diode for in-situ measurement of CVD diamond thickness
PublikacjaIn situ monitoring of the thickness of thin diamond films during technological processes is important because it allows better control of deposition time and deeper understanding of deposition kinetics. One of the widely used techniques is laser reflectance interferometry (LRI) which enables non-contact measurement during CVD deposition. The authors have built a novel LRI system with a 405 nm laser diode which achieves better...
-
Mobile navigation system for visually impaired users in the urban environment
PublikacjaThis paper describes the prototype version of a mobile application supporting independent movement of theblind. Its objective is to improve the quality of life of visually impaired people, providing them with navigationalassistance in urban areas. The authors present the most important modules of the application. The module forprecise positioning using DGPS data from the ASG-EUPOS network as well as enhancements of positioning...
-
Liveness measurements using optical flow for biometric person authentication
PublikacjaAutomatyczne rozpoznawanie twarzy jest jedną z najpopularniejszych technik biometrycznych, jednak nawet najdokładniejsze algorytmy identyfikacji okażą się bezużyteczne, jeśli będzie można je oszukać, np. używając zdjęcia zamiast rzeczywistej osoby. Dlatego też odpowiedni pomiar żywotności jest niezwykle istotny. W pracy zaprezentowano metodę, która jest w stanie rozróżnić pomiędzy sekwencjami wideo pokazującymi żywe osoby oraz...
-
Problems of varistor quality assessment during exploitation
PublikacjaVaristors are commonly used elements which protect power supply networks against high-voltage surges or lightning. Therefore, quality and endurance of these elements is important to avoid losses when an expensive laboratory equipment would not be protected from random overvoltages. Additionally, excessive leakage currents generate serious costs due to high energy consumption. The paper presents shortly properties of varistors that...
-
Radio Link Measurement Methodology for Location Service Applications
PublikacjaThe aim of this paper is the methodology of measurements executed in a radio link for the realization of radiolocation services in radiocommunication networks, particularly in cellular networks. The main results of the measurements obtained in the physical layer of the universal mobile telecommunications system (UMTS) are introduced. A new method for the utilization of the multipath propagation phenomenon to improve the estimation...
-
Ultrasonic spectroscopy of silicon single crystal
PublikacjaSpecimens of Si single crystals with different crystal orientation [100] and [110] were studied by the electro-ultrasonic spectroscopy (EUS) and Resonant Ultrasonic Spectroscopy (RUS). A silicon single crystal is an anisotropic crystal, so its properties are different in different directions in the material relative to the crystal orientation. EUS is based on interaction of two signals: electric AC signal and ultrasonic signal,...
-
Measurements of ASON/GMPLS connection control layer performance according to the ETSI methodology
PublikacjaMeasurements of performance have always been crucial for evaluation of telecommunication systems, especially for implementation of network control elements responsible for connection handling which regards to bandwidth reservation, modification and release. That problem also arises in Automatically Switched Optical Network/Generalized Multiprotocol Label Switching (ASON/GMLPS) architecture, which is considered as one of the components...
-
Distance measurement errors in silent FM-CW sonar with matched filtering
PublikacjaThe secretiveness of sonar operation can be achieved by using continuous frequency-modulated sounding signalswith reduced power and significantly prolonged repeat time. The application of matched filtration in the sonarreceiver provides optimal conditions for detection against the background of white noise and reverberation, and avery good resolution of distance measurements of motionless targets. The article shows that target...
-
Networked Object Monitor - A distributed system for monitoring, diagnostics and control of complex industrial facilities
PublikacjaRozwój mobilności i technologii internetowych, a także globalizacji gospodarki światowej, uwzględniający kluczowe aspekty zarządzania przepływem informacji, otworzył zupełnie nowe możliwości opracowywania i konstruowania innowacyjnych rozwiązań technicznych. Z taką myślą powstał prototyp Sieciowego Monitora Obiektu, aplikacji umożliwiającej nie tylko ciągłą kontrolę parametrów obiektów przemysłowych i biznesowych, ale również zarządzanie...
-
Non-destructive inspection of anti-corrosion protective coatings using optical coherent tomography
PublikacjaW artykule przedstawiono zastosowanie optycznej tomografii koherentnej (OCT) do badania antykorozyjnych powłok ochronnych. Omówiono właściwości optycznej interferometrii niskokoherentnej jako zastosowanej metody pomiarowej, opisano budowę pomiarowego systemu OCT, zbudowanego w Katedrze Metrologii i Optoelektroniki WETI PG. Przy pomocy zrealizowanego systemu przebadano grupę powierzchni metalicznych pokrytych różnymi powłokami antykorozyjnymi....
-
Uncertainty analysis of measuring system for instantaneous power research
PublikacjaThe paper presents a metrological analysis of the measurement system used for diagnosis of induction motor bearings, based on the analysis of the instantaneous power. This system was implemented as a set of devices with dedicated software installed on a PC. A number of measurements for uncertainty estimation was carried out. The results of the measurements are presented in the paper. The results of the aforementioned analysis helped...
-
Distributed System For Noise Threat Evaluation Based On Psychoacoustic Measurements
PublikacjaAn innovative system designed for the continuous monitoring of acoustic climate of urban areas was presentedin the paper. The assessment of environmental threats is performed using online data, acquired through a grid ofengineered monitoring stations collecting comprehensive information about the acoustic climate of urban areas.The grid of proposed devices provides valuable data for the purpose of long and short time acoustic climateanalysis....
-
Validation of Services Supporting Healthcare Standards Conformance
PublikacjaThe paper presents the results of experimental validation of a set of innovative software services supporting processes of achieving, assessing and maintaining conformance with standards and regulations. The study involved several hospitals implementing the Accreditation Standard promoted by the Polish Ministry of Health. First we introduce NOR-STA services that implement the TRUST-IT methodology of argument management. Then we...
-
Characteristics of an image sensor with early-vision processing fabricated in standard 0.35 µm CMOS technology
PublikacjaThe article presents measurement results of prototype integrated circuits for acquisition and processing of images in real time. In order to verify a new concept of circuit solutions of analogue image processors, experimental integrated circuits were fabricated. The integrated circuits, designed in a standard 0.35 µm CMOS technology, contain the image sensor and analogue processors that perform low-level convolution-based image...
-
Evaluation of multimedia applications in a cluster oriented environment
PublikacjaIn the age of Information and Communication Technology (ICT), Web and the Internet have changed significantly the way applications are developed, deployed and used. One of recent trends is modern design of web-applications based on SOA. This process is based on the composition of existing web services into a single scenario from the point of view of a particular user or client. This allows IT companies to shorten product time-to-market....
-
Measurements of OF QoS/QoE parameters for media streaming in a PMIPv6 TESTBED WITH 802.11 b/g/n WLANs
PublikacjaA growing number of mobile devices and the increasing popularity of multimedia services result in a new challenge of providing mobility in access networks. The paper describes experimental research on media (audio and video) streaming in a mobile IEEE 802.11 b/g/n environment realizing network-based mobility. It is an approach to mobility that requires little or no modification of the mobile terminal. Assessment of relevant parameters...
-
Portable exhaled breath analyzer employing fluctuation-enhanced gas sensing method in resistive gas sensors
PublikacjaThis paper presents a portable exhaled breath analyser, developed to detect selected diseases. The set-up employs resistive gas sensors: commercial MEMS sensors and prototype gas sensors made of WO3 gas sensing layers doped with various metal ingredients. The set-up can modulate the gas sensors by applying UV light to induce physical changes of the gas sensing layers. The sensors are placed in a tiny gas chamber of a volume...
-
Economical methods for measuring road surface roughness
PublikacjaTwo low-cost methods of estimating the road surface condition are presented in the paper, the first one based on the use of accelerometers and the other on the analysis of images acquired from cameras installed in a vehicle. In the first method, miniature positioning and accelerometer sensors are used for evaluation of the road surface roughness. The device designed for installation in vehicles is composed of a GPS receiver and...
-
DIAGNOSIS OF MALIGNANT MELANOMA BY NEURAL NETWORK ENSEMBLE-BASED SYSTEM UTILISING HAND-CRAFTED SKIN LESION FEATURES
PublikacjaMalignant melanomas are the most deadly type of skin cancer but detected early have high chances for successful treatment. In the last twenty years, the interest of automated melanoma recognition detection and classification dynamically increased partially because of public datasets appearing with dermatoscopic images of skin lesions. Automated computer-aided skin cancer detection in dermatoscopic images is a very challenging task...
-
Computationally efficient two-objective optimization of compact microwave couplers through corrected domain patching
PublikacjaFinding an acceptable compromise between various objectives is a necessity in the design of contemporary microwave components and circuits. A primary reason is that most objectives are at least partially conflicting. For compact microwave structures, the design trade-offs are normally related to the circuit size and its electrical performance. In order to obtain comprehensive information about the best possible trade-offs, multi-objective...
-
MACHINE LEARNING SYSTEM FOR AUTOMATED BLOOD SMEAR ANALYSIS
PublikacjaIn this paper the authors propose a decision support system for automatic blood smear analysis based on microscopic images. The images are pre-processed in order to remove irrelevant elements and to enhance the most important ones - the healthy blood cells (erythrocytes) and the pathologic (echinocytes). The separated blood cells are analyzed in terms of their most important features by the eigenfaces method. The features are the...
-
A random signal generation method for microcontrollers with DACs
PublikacjaA new method of noise generation based on software implementation of a 7-bit LFSR based on a common polynomial PRBS7 using microcontrollers equipped with internal ADCs and DACs and a microcontroller noise generator structure are proposed in the paper. Two software applications implementing the method: written in ANSI C and based on the LUT technique and written in AVR Assembler are also proposed. In the method the ADC results are...
-
Efficiency of linear and non-linear classifiers for gas identification from electrocatalytic gas sensor
PublikacjaElectrocatalytic gas sensors belong to the family of electrochemical solid state sensors. Their responses are acquired in the form of I-V plots as a result of application of cyclic voltammetry technique. In order to obtain information about the type of measured gas the multivariate data analysis and pattern classification techniques can be employed. However, there is a lack of information in literature about application of such...
-
QUASI-DISTRIBUTED NETWORK OF LOW-COHERENCE FIBER-OPTIC FABRY-PÉROT SENSORS WITH CAVITY LENGTH-BASED ADDRESSING
PublikacjaDistributed measurement often relies on sensor networks. In this paper, we present the construction of low coherent fiber-optic Fabry-Pérot sensors connected into a quasi-distributed network. We discuss the mechanism of spectrum modulation in this type of sensor and the constraints of assembly of such sensors in the network. Particular attention was paid to separate the signals from individual sensors, which can be achieved by...
-
EVALUATION OF LIQUID-GAS FLOW IN PIPELINE USING GAMMA-RAY ABSORPTION TECHNIQUE AND ADVANCED SIGNAL PROCESSING
PublikacjaLiquid-gas flows in pipelines appear in many industrial processes, e.g. in the nuclear, mining, and oil industry. The gamma-absorption technique is one of the methods that can be successfully applied to study such flows. This paper presents the use of thegamma-absorption method to determine the water-air flow parameters in a horizontal pipeline. Three flow types were studied in this work: plug, transitional plug-bubble,...
-
Spatial sensitivity to the conductivity changes of a four electrode probe.
PublikacjaW artykule rozważana jest czułość przestrzenna, czteropunktowej, liniowej sondy na zmiany przewodności zachodzące w badanym materiale. Otrzymane wyniki wskazują, że czułość może być zarówno dodatnia i ujemna, tzn. wzrost przewodności może prowadzić zarówno do wzrostu lub do spadku mierzonej impedancji. W artykule rozważane są materiały zarówno izotropowe jak i anizotropowe. Uzyskane wyniki pozwalają wyjaśnić dlaczego niektóre...
-
O działalności Komitetu Metrologii i Aparatury Naukowej Polskiej Akademii Nauk w roku 2002
PublikacjaPrzedstawiono skład osobowy oraz struktury działalności Komitetu Metrologii Aparatury Naukowej PAN. Opisano bardziej szczegółowo działalność naukową i organizacyjną, aktywność konferencyjną krajową i międzynarodową oraz aktywność wydawniczą w roku 2002.
-
A metrological analysis of the input circuit of an impedance meter.
PublikacjaW pracy przeprowadzono analizę obwodu wejściowego miernika impedancji W analizie obwodu wejściowego, uwzględniono najważniejsze czynniki wpływające na sygnały na jego wejściu: parametry zmiennoprądowe zastosowanych wzmacniaczy, rezystancję zakresową przetwornika prąd-napięcie, pojemności montażowe. Przeprowadzono symulację sygnałów wydzielanych w obwodzie dla różnych wartości pojemności pasożytniczych, następnie dokonano badań...
-
Assessment of cardiovascular risk in assisted living
PublikacjaWady i choroby układu krążenia są jedną z podstawowych przyczyn problemów zdrowotnych oraz przyczyn śmierci. Wczesne ich wykrycie jest szczególnie cenne jako, że może zapobiec przez poważnymi incydentami (np. zawał, udar, itp.). W artykule przedstawiono nasobny system pomiarowy integrujący wiele pomiarów przydatnych do oceny problemów kardiologicznych.Disorders of the heart and blood vessels are the leading cause of health problems...
-
Measures for Evaluation of Structure and Semantics of Ontologies
PublikacjaArtykuł przedstawia zagadnienie miar jakości ontologii ze szczególnym uwzględnieniem ich podziału na syntaktyczne (strukturalne) i semantyczne. Na tym tle przedstawione jest nowe podejście do pomiaru właściwości semantycznych ontologii bazujące na kartografii wiedzy.
-
Accuracy assessment of mobile satellite measurements in relation to the geometrical layout of rail tracks
PublikacjaThe paper presents the campaigns of mobile satellite measurements, carried out in 2009–2015 on the railway and tram lines. The accuracy of the measurement method has been analysed on the basis of the results obtained in both horizontal and vertical planes. The track axis deviation from the defined geometric shape has been analysed in the areas clearly defined in terms of geometry, i.e. on the straight sections and sections with...
-
Transmission Protocol Simulation Framework For The Resource-Constrained Wireless Sensor Network
PublikacjaIn this paper a prototype framework for simulation of wireless sensor network and its protocols are presented. The framework simulates operation of a sensor network with data transmission, which enables simultaneous development of the sensor network software, its hardware and the protocols for wireless data transmission. An advantage of using the framework is converging simulation with the real software. Instead of creating...
-
Determination Of Gas Mixture Components Using Fluctuation Enhanced Sensing And The LS-SVM Regression Algorithm
PublikacjaThis paper analyses the effectiveness of determining gas concentrations by using a prototype WO3 resistive gas sensor together with fluctuation enhanced sensing. We have earlier demonstrated that this method can determine the composition of a gas mixture by using only a single sensor. In the present study, we apply Least-Squares Support-Vector-Machine-based (LS-SVM-based) nonlinear regression to determine the gas concentration...
-
Zespół Metrologii i Optoelektroniki
Zespoły Badawcze* komputerowo wspomagana metrologia i diagnostyka * projektowanie systemów * mikrosystemów i makrosystemów elektronicznych * testowanie i diagnostyka elektroniczna * pomiary właściwości szumowych i zakłóceń * spektroskopia impedancyjna * telemetria i telediagnostyka internetowa * katedra redaguje Metrology and Measurement Systems * kwartalnik PAN znajdujący się na liście JCR
-
The impact of surface slope and calculation resolution on the fractal dimension for fractures of steels after bending-torsion fatigue
PublikacjaThe article presents the results of the fractal dimension measurements on the fatigue fracture surfaces of 10HNAP and S355J2 steels specimens after combined bending-torsion fatigue. For smooth and ring-notched specimens, three loading conditions were analyzed: (1) bending; (2) bending-torsion; and (3) torsion fatigue. Post-failure surface topography measurements were carried out on the entire fracture surfaces using an optical...
-
Biopaliwa z rzepaku. Przygotowanie surowca do otrzymywania biodiesla w warunkach gospodarstwa rolnego oraz pilotowe metanolizy
PublikacjaScharakteryzowano olej rzepakowy jako surowiec do produkcji biodiesla i opisano etapy procesu transestryfikacji. Oceniono metody wydobywania oleju rzepakowego poprzez tłoczenie w warunkach gospodarstwa rolnego i scharakteryzowano oleje pod względem przydatności do reakcji metanolizy (zawartość fosforu, LK, LOO, skład kwasów tłuszczowych). Przeprowadzono wstępne, laboratoryjne reakcje transestryfikacji i na ich podstawie wytypowano...
-
Wykorzystanie różnych form opadów i osadów atmosferycznych do oceny zanieczyszczenia środowiska w różnych regionach geograficznych Polski. Część I - mgła
PublikacjaWykonano badania zebranych próbek opadu zawieszonego (mgła) w celu oznaczenia w nich poziomu zawartości wybranych związków organicznych i nieorganicznych. Próbki pobierano w dwóch punktach na terenie Polski. Miejsca pobierania próbek podzielono ze względu na ich różny charakter: teren nizinny i szczyt górski. Stwierdzono obecnośćwybranych zanieczyszczeń na różnych poziomach stężeń w próbkach mgły oraz zależność tego poziomu od...
-
Determination of Toxicological Parameters of Selected Bioactive Organic Chemicals Using the Ostracodtoxkit FTM
PublikacjaAssessment of the impact of pharmaceutical residues on living organisms is very complex subject. Apart from taking into account the toxicity of individual compounds also their presence in mixtures should be taken into account. In this work, attempts were made to assess the ecotoxicity of biologically active substances (with 50 % effective concentration (EC50) values growing from fluoxetine (EC50 = 4.431 nM) >> gemfibrozil ≈ 17α-ethinylestradiol...
-
Przegląd metod zagospodarowania odcieku glicerynowego z procesu produkcji biopaliwa rzepakowego
PublikacjaZagospodarowanie fazy glicerynowej - produktu odpadowego powstającego podczas wytwarzania estrów metylowych oleju rzepakowego (RME - Rapeseed Methyl Esters), jest ważnym elementem wspierającym produkcję biopaliw zarówno w aspekcie ekonomicznym, jak i ekologicznym. Rafinerie wytwarzające biodiesla na skalę przemysłową stosują najczęściej technologie oczyszczania fazy glicerynowej do postaci czystej gliceryny, możliwej do zastosowania...
-
RAPESEED PELLET - A BYPRODUCT OF BIODIESEL PRODUCTION - AS AN EXCELLENT RENEWABLE ENERGY SOURCE
PublikacjaVegetable oils are renewable feedstock currently being used for production of biofuels from sustainable biomass resources. The existing technology for producing diesel fuel from plant oils, such as rapeseed, soybean, canola and palm oil are largely centered on transesterification of oils with methanol to produce fatty acid methyl esters (FAME) or biodiesel. Rapeseed pellet - crushed seed residue from oil extraction is a byproduct...
-
CURRENT TRENDS IN RECYCLING OF PHOTOVOLTAIC SOLAR CELLS AND MODULES WASTE
PublikacjaIn comparison to other energy producing techniques, photovoltaics (PV) is one of the most promising options: no emission of any matter into the environment during operation; extremely long operation period (estimated average: 25 years), minimum maintenance, robust technique, aesthetic aspects. The use of photovoltaics is rapidly increasing, and the respective market is developing accordingly. Although PV manufacturing equipment...
-
Scalable Measurement System for Multiple Impedance Gas Sensors
PublikacjaAuthor proposes scalable architecture of the measurement system for gas sensor with impedance dependance of the gas concentration. The main part of the system is a single-board impedance analyser. The number of analysers working in parallel can be configured according to specific application. The system is controlled by a single computer which organises the measurement cycle and store the acquired measurement data. The system is...
-
Janusz Smulko prof. dr hab. inż.
OsobyUrodził się 25 kwietnia 1964 r. w Kolnie. Ukończył w 1989 r. z wyróżnieniem Wydział Elektroniki Politechniki Gdańskiej, specjalność aparatura pomiarowa. Zajął II miejsce w konkursie Czerwonej Róży na najlepszego studenta Wybrzeża w 1989 r. Od początku kariery związany z Politechniką Gdańską: asystent (1989–1996), adiunkt (1996–2012), profesor nadzwyczajny PG (od 2012). Odbył staże naukowe w Texas A&M University (2003, NATO...
-
Robert Bogdanowicz dr hab. inż.
OsobyRobert Bogdanowicz received his Ph.D. degree with honours in Electronics from the Gdansk University of Technology. He worked as a post-doc researcher in Ernst-Moritz-Arndt-Universität Greifswald Institut für Physik. He has initiated optical emission imaging of muti-magnetron pulsed plasma and contributed to the development of antibacterial implant coatings deposited by high-power impulse magnetron sputtering. He moved back to...
-
Grzegorz Lentka dr hab. inż.
OsobyGrzegorz Lentka uzyskał tytuł magistra inżyniera w roku 1996 na Wydziale Elektroniki, Telekomunikacji i Informatyki Politechniki Gdańskiej w zakresie systemów pomiarowych. Stopień doktora nauk technicznych uzyskał w roku 2003, a doktora habilitowanego w 2014. Obecnie zatrudniony jest w Katedrze Metrologii i Optoelektroniki na stanowisku profesora PG. W ramach prowadzonej dydaktyki zajmuje się zagadnieniami związanymi z interfejsami...
-
Dariusz Świsulski dr hab. inż.
Osoby -
Arkadiusz Szewczyk dr inż.
OsobyArkadiusz Szewczyk uzyskał tytuł magistra inżyniera w roku 1996 na Wydziale Elektroniki, Telekomunikacji i Informatyki Politechniki Gdańskiej w zakresie aparatury elektronicznej. Stopień doktora nauk technicznych uzyskał w roku 2002 w ramach współpracy pomiędzy Politechniką Gdańską a Institut National Polytechnique de Grenoble we Francji. Obecnie zatrudniony jest w Katedrze Metrologii i Optoelektroniki na stanowisku adiunkta. W...