Filtry
wszystkich: 1547
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: cfd, model tests, pow test, propeller, validation
-
Flow Analysis of a Kaplan Turbine
PublikacjaThis monograph is a guide to a method of experimental and numerical flow investigations for Kaplan - type turbines. The numerical calculations were compared with the test results of the model Kaplan turbine. The tests were carried out on the model test rig in the Gdańsk University of Technology. The turbine has been thoroughly experimentally investigated, resulting in the identification of optimum setting combination of the stator...
-
High frequency test measurements on physical model of power transformer with use of FRAX analyzer Streszczenie. W niniejszym artykule przedstawiono pomiary testowe SFRA wykonane na modelu fizycznym transformatora elektroenergetycznego
Publikacja -
Influence of Properties of Hydraulic Fluid on Pressure Peaks in Axial Piston Pumps’ Chambers
PublikacjaThe article concentrates on the research of the pressure peaks in a working chamber of an axial piston pump. The main focus of the article is the influence of fluid properties on the pressure peaks value. Experimental and analytical methods were used to determine the impact of the fluid density, viscosity, compressibility and aeration. The article describes the pressure peak generation process and explains the theoretical basis...
-
Experimental and Computational Analysis of the Ship Propeller in Open Water Conditions for Inclined Flow
PublikacjaThe paper presents the results of computational analyses simulating the open water tests of ship propeller in inclined flow. The results of computations are compared with the results of corresponding experimental analyses carried out in the towing tank of Ship Design and Research Centre (CTO S.A.). The object of the research was the model propeller identified as CP469. The aim of the study was to validate the results of numerical...
-
ENERGY ANALYSIS OF THE PROPULSION SHAFT FATIGUE PROCESS IN A ROTATING MECHANICAL SYSTEM PART II IDENTIFICATION STUDIES – DEVELOPING THE FATIGUE DURABILITY MODEL OF A DRIVE SHAFT
PublikacjaThe article presents a continuation of research carried out concerning identification of energy consequences of mechanical fatigue within a propeller shaft in a rotating mechanical system, while working under conditions of the loss of the required alignment of shaft lines. Experimental research was carried out on a physical model reflecting a full-sized real object: i.e., the propulsion system of the ship. It is proven, by means...
-
Heavy duty vehicle fuel consumption modelling using artificial neural networks
PublikacjaIn this paper an artificial neural network (ANN) approach to modelling fuel consumption of heavy duty vehicles is presented. The proposed method uses easy accessible data collected via CAN bus of the truck. As a benchmark a conventional method, which is based on polynomial regression model, is used. The fuel consumption is measured in two different tests, performed by using a unique test bench to apply the load to the engine. Firstly,...
-
Janusz Kozak prof. dr hab. inż.
OsobyDr hab. inż. Janusz Kozak Dziekan Wydziału Oceanotechniki i Okrętownictwa Politechniki Gdańskiej Urodzony: 04.07.1953 w Pucku Absolwent Technikum Budowy Okrętów „Conradinum” w Gdańsku, 1973. Absolwent Instytutu Okrętowego PG, 1978. Po ukończeniu studiów praca w Stoczni Gdynia, a od roku 1980 w Katedrze Technologii Okrętów Instytutu Okrętowego a później Wydziału Oceanotechniki i Okrętownictwa Politechniki Gdańskiej kolejno na...
-
Tensile curve of E grade steel for shipbuilding
Dane BadawczeIn the shipbuilding industry, the risk of brittle fractures developing in constructions is limited by employing certified materials of specific impact strength, determined using the Charpy method (for a given design temperature) and by exercising control over the welding processes (technology qualification, supervision of production, tests of non-destructive...
-
ENERGY ANALYSIS OF PROPULSION SHAFT FATIGUE PROCESS IN ROTATING MECHANICAL SYSTEM PART I TESTING SIGNIFICANCE OF INFLUENCE OF SHAFT MATERIAL FATIGUE EXCITATION PARAMETERS
PublikacjaThe article discusses the problem of mathematical modelling of energy conversion processes in a rotating mechanical system for the purpose of identifying fatigue states of propulsion shafts in this system. A simplified physical model of the analysed system, constructed in an appropriate scale, has made the basis for the experimental research. The research programme took into consideration mechanical fatigue excitation of the model...
-
Five-phase induction motor drive with sine-wave filter
PublikacjaThe paper presents closed loop ac drive with 5 phase induction motor operating with voltage source inverter and sine wave filter. The motor supply voltages and currents have sinusoidal shape. For well known adjustable electric drives the field oriented control method with flux and speed co ntrol can be applied. In the presence of output filter both control and estimation algorithms should be modified due to sine wave filter installation....
-
Lagrangian model of an isolated dc-dc converter with a 3-phase medium frequency transformer accounting magnetic cross saturation
PublikacjaThis article presents a nonlinear equivalent circuit model of an isolated dc-dc converter with a 3-phase medium frequency transformer. The model takes into account the magnetic cross saturation of the 3-phase core-type magnetic circuit. The model is suitable in detailed electromagnetic transient simulations of power systems involving isolated dc-dc converters. The model is developed using the Lagrange energy method. It involves...
-
Ring thruster - a preliminary optimisation study
PublikacjaThe ring thruster is a new type of propeller, for which there is no experimental data to verify analytical design calculations. A significant feature of the ring thruster is the absence of a shaft. Propeller blades are mounted to the ring rotating inside the housing, which has the shape of a nozzle. For this reason the ring thruster is closest, with respect to both the construction and principle of operation, to the Kort nozzle...
-
Edgewise Compressive Behavior of Composite Structural Insulated Panels with Magnesium Oxide Board Facings
PublikacjaEdgewise compression response of a composite structural insulated panel (CSIP) with magnesium oxide board facings was investigated. The discussed CSIP is a novel multifunctional sandwich panel introduced to the housing industry as a part of the wall, floor, and roof assemblies. The study aims to propose a computational tool for reliable prediction of failure modes of CSIPs subjected to concentric and eccentric axial loads. An advanced...
-
Alicja Sekuła dr hab. inż.
Osoby- 2017 r. - stopień doktora habilitowanego nauk ekonomicznych w dziedzinie ekonomia, dyscyplina - finanse; Szkoła Główna Handlowa, Kolegium Zarządzania i Finansów, - 2003 r. - stopień doktora nauk ekonomicznych w dziedzinie ekonomia, dyscyplina - ekonomia; Politechnika Gdańska, Wydział Zarządzania i Ekonomii, - 1997 r. - tytuł magister inżynier - Politechnika Gdańska, Wydział Zarządzania i Ekonomii, - 1996 r. - tytuł magister inżynier...
-
Wiktoria Wojnicz dr hab. inż.
OsobyDSc in Mechanics (in the field of Biomechanics) - Lodz Univeristy of Technology, 2019 PhD in Mechanics (in the field of Biomechanics) - Lodz Univeristy of Technology, 2009 (with distinction) Publikacje z listy MNiSW (2009 - ) Wojnicz W., Wittbrodt E., Analysis of muscles' behaviour. Part I. The computational model of muscle. Acta of Bioengineering and Biomechanics, Vol. 11, No.4, 2009, p. 15-21 Wojnicz W., Wittbrodt E., Analysis...
-
From U2TP Models to Executable Tests with TTCN-3
PublikacjaThe approach towards system engineering according to Model-Driven Architectures (MDA) with code generation derived from model implies also an increased need for research on automation of the test generation process. This paper presents an approach to derive executable tests from UML 2.0 Testing Profile diagrams automatically. In particular, an approach to derive executable tests within the Testing and Test Control Notation (TTCN-3)...
-
Impact of Propeller Emergence on Hull, Propeller, Engine, and Fuel Consumption Performance in Regular Head Waves
PublikacjaIn this study, the impact of propeller emergence on the performance of a ship (speed), propeller (thrust, torque, and RPM), a diesel engine (torque and RPM) and fuel consumption are analysed under severe sea conditions. The goal is to describe the variation in the system variables and fuel consumption rather than analysing the motion of the ship or the phenomenon of propeller ventilation in itself. A mathematical model of the...
-
Jakub Konkol dr inż.
Osoby -
Prediction of manoeuvring abilities of 10000 DWT pod-driven coastal tanker
PublikacjaThis paper aims to present a new approach in the prediction of manoeuvring abilities of pod-driven ships. A new mathematical model of motions based on MMG methodology was developed and a new type of description of forces acting on azimuth drives is presented. Captive model tests of medium-size coastal tanker and pod open water tests were carried out in CTO S.A. (Ship Design and Research Centre S.A.) to obtain hull hydrodynamic derivatives...
-
The Analysis of Overall Ship Fuel Consumption in Acceleration Manoeuvre using Hull-Propeller-Engine Interaction Principles and Governor Features
PublikacjaThe problem of reduction of greenhouse gas emissions in shipping is currently addressed by many research works and related industries. There are many existing and visionary technologies and ideas, which are conceptually defined or practically realised. This goal can be achieved in different ways, and reducing fuel consumption is one of the major methods. In these circumstances, the aim of this study is to analyse the possibility...
-
TIME-DOMAIN NUMERICAL EVALUATION OF SHIP RESISTANCE AND MOTION IN REGULAR WAVES BY USING THE CFD URANS METHOD
PublikacjaTaking into account the International Maritime Organisation’s (IMO) strategy to radically reduce the GHG emitted by the shipping industry towards zero emission operation, today's assessment of ship behaviour in waves, its seakeeping characteristics and resistance and their interrelation with fuel consumption and emissions are one of the most attended research subject. There are three methods to conduct this analysis, which are...
-
Evaluation of Asphalt Mixture Low-Temperature Performance in Bending Beam Creep Test
PublikacjaLow-temperature cracking is one of the most common road pavement distress types in Poland. While bitumen performance can be evaluated in detail using bending beam rheometer (BBR) or dynamic shear rheometer (DSR) tests, none of the normalized test methods gives a comprehensive representation of low-temperature performance of the asphalt mixtures. This article presents the Bending Beam Creep test performed at temperatures from −20...
-
Tensile strength test of PE foils modified with zinc oxide and zinc salts
Dane BadawczeThis dataset contains the results of PE foils mechanical tests, in which the material was evaluated for strength and extensibility at the moment of breaking and based on the same tests preceded by material fatigue in 50 stretching cycles. The principle of the method is to stretch the test sample placed in the clamps of the stretching apparatus at a...
-
Machine-aided detection of SARS-CoV-2 from complete blood count
PublikacjaThe current gold standard for SARS-CoV-2 detection methods lacks the functionality to perform population screening. Complete blood count (CBC) tests are a cost-effective way to reach a wide range of people – e.g. according to the data of the Central Statistical Office of Poland from 2016, there are 3,000 blood diagnostic laboratories in Poland, and 46% of Polish people have at least one CBC test per year. In our work, we show...
-
Measurements of raising of 160EC pantograph type
Dane BadawczeIn this description the results of the experiment and also simulation performed on the total assembly of the 160 EC pantograph type is given. Multibody dynamics of pantograph rising due to external torque and forces are measured for parameter validation of the pantograph model.
-
Laboratory Determination of Burger's Model Parameters for Visco-elastic Analysis of Road Pavement Materials
PublikacjaBurger's Model is one of those models that describes performance of asphalt mixtures. Its parameters can be used in road construction analysis based on visco-elastic properties in wide variety of temperatures using dedicated programs (e.g. Veroad) or in Finite Element Method (FEM). Parameters of Burger's Model can be used for example in prediction of low temperature cracking in low winter temperatures or permanent deformation...
-
Numerical analysis of lumbar spine injury during road safety barrier collision
PublikacjaPurpose: Enhancing road safety is a critical goal worldwide, necessitating the development of clear standards for road safety systems. This study focuses on lumbar spine (L-spine) compression injuries during collisions with concrete road safety barriers (RSBs). It aims to analyze internal forces during impact to understand L-spine injury biomechanics in such accidents. Methods: The research included a literature review, analyzing...
-
Testing impedance analyzer with potentiostat using RC model with Si diode at 200 mV
Dane BadawczeThe dataset presents impedance spectrum non-linear RC model with diode presented in the figure below. This model was used as a test engine of the impedance analyzer with potentiostat described in the referenced paper. When changing the DC polarisation of the model the non-linear phenomena could be observed. Thanks to this, the model can be used as a...
-
Testing impedance analyzer with potentiostat using RC model with Si diode at 0 V
Dane BadawczeThe dataset presents impedance spectrum non-linear RC model with diode presented in the figure below. This model was used as a test engine of the impedance analyzer with potentiostat described in the referenced paper. When changing the DC polarisation of the model the non-linear phenomena could be observed. Thanks to this, the model can be used as a...
-
Testing impedance analyzer with potentiostat using RC model with Si diode at 600 mV
Dane BadawczeThe dataset presents impedance spectrum non-linear RC model with diode presented in the figure below. This model was used as a test engine of the impedance analyzer with potentiostat described in the referenced paper. When changing the DC polarisation of the model the non-linear phenomena could be observed. Thanks to this, the model can be used as a...
-
Testing impedance analyzer with potentiostat using RC model with Si diode at 400 mV
Dane BadawczeThe dataset presents impedance spectrum non-linear RC model with diode presented in the figure below. This model was used as a test engine of the impedance analyzer with potentiostat described in the referenced paper. When changing the DC polarisation of the model the non-linear phenomena could be observed. Thanks to this, the model can be used as a...
-
Simulations of hydro-fracking in rock mass at meso-scale using fully coupled DEM/CFD approach
PublikacjaThe paper deals with two-dimensional (2D) numerical modelling of hydro-fracking (hydraulic fracturing) in rocks at the meso-scale. A numerical model was developed to characterize the properties of fluid-driven fractures in rocks by combining the discrete element method (DEM) with computational fluid dynamics (CFD). The mechanical behaviour of the rock matrix was simulated with DEM and the behaviour of the fracturing fluid flow...
-
Simulations of wave propagation and attenuation in fields of colliding ice floes
Dane BadawczeThis dataset contains results of numerical smulations of sea ice-wave interactions, corresponding to laboratory experiments conducted at the Large Ice Model Basin (LIMB) at the Hamburg Ship Model Basin (HSVA) as part of the LS-WICE ("Loads on Structure and Waves in Ice"; https://zenodo.org/record/1067170#.XrLt_dhpxhE) project. THe simulations were conducted...
-
COVID-19 severity forecast based on machine learning and complete blood count data
PublikacjaProper triage of COVID-19 patients is a key factor in eective case management, especially with limited and insucient resources. In this paper, we propose a machine-aided diagnostic system to predict how badly a patient with COVID-19 will develop disease. The prognosis of this type is based on the parameters of commonly used complete blood count tests, which makes it possible to obtain data from a wide range of patients.We chose...
-
COVID-19 severity forecast based on machine learning and complete blood count data
PublikacjaProper triage of COVID-19 patients is a key factor in eective case management, especially with limited and insucient resources. In this paper, we propose a machine-aided diagnostic system to predict how badly a patient with COVID-19 will develop disease. The prognosis of this type is based on the parameters of commonly used complete blood count tests, which makes it possible to obtain data from a wide range of patients.We chose...
-
Combined numerical and experimental approach to determine numerical model of abdominal scaffold
PublikacjaA proper junction of the prosthesis and the abdominal wall is important in successful hernia repair. The number of tacks should be balanced to assure appropriate mesh fixation and not to induce post-operative pain. Numerical simulations help to find this balance. The study is aimed at creating a proper numerical model of a knitted surgical mesh subjected to boundary conditions and load occurring in the abdominal cavity. Continuous,...
-
OBTAINING FLUID FLOW PATTERN FOR TURBINE STAGE WITH NEURAL MODEL.
PublikacjaIn the paper possibility of applying neural model to obtaining patterns of proper operation for fluid flow in turbine stage for fluid-flow diagnostics is discussed. Main differences between Computational Fluid Dynamics (CFD) solvers and neural model is given, also limitations and advantages of both are considered. Time of calculations of both methods was given, also possibilities of shortening that time with preserving the accuracy...
-
Blade Section Prpfile Array Lifting Surface Design Method for Marine Screw Propeller Blade
PublikacjaThe lifting surface model is widely used in screw propeller design and analysis applications. It serves as a reliable tool for determination of the propeller blade mean line and pitch distribution. The main idea of this application was to determine the blade shape that would satisfy the kinematic boundary condition on its surface with the prescribed bound circulation distribution over it. In this paper a simplified lifting surface...
-
Selected Technical Issues of Deep Neural Networks for Image Classification Purposes
PublikacjaIn recent years, deep learning and especially Deep Neural Networks (DNN) have obtained amazing performance on a variety of problems, in particular in classification or pattern recognition. Among many kinds of DNNs, the Convolutional Neural Networks (CNN) are most commonly used. However, due to their complexity, there are many problems related but not limited to optimizing network parameters, avoiding overfitting and ensuring good...
-
Analiza możliwości zastosowania środowiska SCILAB do wspomagania projektowania podsystemów energetycznych statków = Analysis of capability of using SCILAB for adding design of power ship subsystems
PublikacjaW artykule przedstawiono koncepcję wykorzystania środowiska symulacyjnego Scilab, modeli matematycznych oraz badań symulacyjnych przy projektowaniu podsystemów energetycznych statku. Zredagowano przykładową strukturę zawierającą model wysokoprężnego silnika oraz model śruby okrętowej. Przedstawione procedury oraz modele matematyczne zostaną włączone do systemu ekspertowego wspomagającego projektowanie statków. This paper deals...
-
Dynamic effect of the vehicle passing under lightweight footbridge.
PublikacjaThe paper describes a numerical study of dynamic response of cable-stayed steel footbridge for a big lorry passing underneath. The footbridge is an existing object crossing Wolska street in Warsaw. The structural model of footbridge was verified by dynamic test loading. A numerical study of a vehicle passing under footbridge is presented. 2D and 3D incompressible flow fields are modeled using sliding mesh in transient CFD computation....
-
Badania układu UPFC w oparciu o model laboratoryjny i symulacyjny
PublikacjaW artykule przedstawiono koncepcję oraz sposób realizacji laboratoryjnego modelu układu UPFC. Układ zrealizowano według nowej metodyki oferującej elastyczność w szerokim zakresie testowania nowych algorytmów sterowania. W referacie zaprezentowano też przykładowe wyniki prób eksperymentalnych potwierdzające słuszność przyjętej koncepcji sterowania. Dane pomiarowe zostały również wykorzystane do celów walidacji opracowanego modelu...
-
The electrochemical response to glassy carbon electrode modification steps towards viral electrochemical immunosensor preparation
Dane BadawczeThe dataset contains the electrochemical measurements (CV/EIS) carried out for the consecutive steps of the glassy carbon GC electrode functionalization, in separate subfolders, as described. The cyclic voltammetry (CV) was conducted using a Palmsens 4 potentiostat/galvanostat system (Methrom, Autolab, Netherlands) in the standard three-electrode configuration,...
-
Simulation of the remanence influence on the transient states in a single-phase multiwinding transformer
PublikacjaThis paper presents the mathematical model of a single-phase multi-winding core type transformer taking into account magnetic hysteresis phenomenon based on the feedback Preisach model (FPM). The set of loop differential equations was developed for a K-th winding transformer model where the flux linkages of each winding includes flux Φ common to all windings as a function of magneto motive force Θ of all windings. The first purpose...
-
The electrochemical response to Au electrode modification steps towards viral electrochemical immunosensor preparation
Dane BadawczeThe dataset contains the electrochemical measurements (CV/EIS) carried out for the consecutive steps of the Au electrode functionalization, in separate subfolders, as described. The cyclic voltammetry (CV) was conducted using a Palmsens 4 potentiostat/galvanostat system (Methrom, Autolab, Netherlands) in the standard three-electrode configuration, with...
-
Experimental and numerical analysis of the modified TB32 crash tests of the cable barrier system
PublikacjaRoad restraint systems, including safety barriers, are one of the means used to improve road safety. Currently, they can be allowed to general use after passing the specific crash tests. However, it is always important and desirable to evaluate their performance under various realistic conditions, which can happen on the roads. In this study, the behaviour of the cable barrier system in impact conditions different than assumed...
-
Dynamic tests of composite footbridge segment – experimental and numerical studies
PublikacjaExperimental dynamic tests and numerical simulations of a 3 meters long segment of a footbridge made of polymer composites are presented in the paper. The span-length is reduced, however dimensions of cross-section are the same as the target footbridge. The segment structure is made of sandwich panels, which consist of fibre reinforced polymer (GFRP) laminates (skins) and a PET foam (core). The first part of the paper contains...
-
Quality Assurance and Quality Control in the Analytical Chemical Laboratory. A practical approach : Second edition
PublikacjaThe second edition defines the tools used in QA/QC, especially the application of statistical tools during analytical data treatment. Clearly written and logically organized, it takes a generic approach applicable to any field of analysis. The authors begin with the theory behind quality control systems, then detail validation parameter measurements, the use of statistical tests, counting the margin of error, uncertainty estimation,...
-
Equivalent standard manoeuvres for pod-driven ships
PublikacjaProcedures for carrying out the manoeuvring tests presented in International Maritime Organisation (IMO) resolution MSC.137(76) are based on the capabilities of ships with conventional steering-propulsion systems. Therefore they do not correspond to ships with other steering-propulsion devices, like pod drives. IMO is aware of this shortcoming and for ships with non-conventional steering and propulsion system may permit the use...
-
Towards application of uncertainty quantification procedure combined with experimental procedure for assessment of the accuracy of the DEM approach dedicated for granular flow modeling
PublikacjaThere is a high demand for accurate and fast numerical models for dense granular flows found in many industrial applications. Nevertheless, before numerical model can be used its need to be always validated against experimental data. During the validation, it is important to consider how the measurement data sets, as well as the numerical models, are affected by errors and uncertainties. In this study, the uncertainty quantification...