wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: diameter
-
Analysis of Modal Parameters Using a Statistical Approach for Condition Monitoring of the Wind Turbine Blade
PublikacjaThe primary objective of the presented paper is the numerical and experimental investigation related to developing a useful diagnostic method, which can be used for determining the site and size of damage in laminated shells of wind turbine blades. The described detection technique is based on the analysis of low frequencies bending vibrations mode shapes of rotor blades. The authors used the commonly applied statistics methods...
-
Parametric Study on a Performance of a Small Counter-Rotating Wind Turbine
PublikacjaA small Counter-Rotating Wind Turbine (CRWT) has been proposed and its performancehas been investigated numerically. Results of a parametric study have been presented in this paper.As parameters, the axial distance between rotors and a tip speed ratio of each rotor have been selected.Performance parameters have been compared with reference to a Single Rotor Wind Turbine (SRWT).Simulations were carried out with Computational Fluids...
-
Thermogravimetric measurement (TG) of 10 wt.% Ce0.8La0.2O2-NiO-YSZ anode for DIR-SOFC
Dane BadawczeThe daataset includes the thermogravimetric measurement (TG) of Ce0.8La0.2O2-NiO-YSZ anode for DIR-SOFC. The mesurement was performed under synthestic air atmosphere. The anode was composed of NiO-YSZ cermet composite (90 wt%) and Ce0.8La0.2O2-s additive (10wt%) with the addition of poroformer - PMMA granules 8um diameter (40 vol.% of whole powder volume)....
-
Thermogravimetric measurement (TG) of 20wt.% Ce0.8La0.2O2-NiO-YSZ anode for DIR-SOFC
Dane BadawczeThe daataset includes the thermogravimetric measurement (TG) of Ce0.8La0.2O2-NiO-YSZ anode for DIR-SOFC. The mesurement was performed under synthestic air atmosphere. The anode was composed of NiO-YSZ cermet composite (80 wt%) and Ce0.8La0.2O2-s additive (20wt%) with the addition of poroformer - PMMA granules 8um diameter (40 vol.% of whole powder volume)....
-
Prediction of pile shaft capacity in tension based on some direct CPT methods – Vistula Marshland test site
PublikacjaThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with a diameter of 0.4 m and the length...
-
Ordered titanium templates functionalized by gold films for biosensing applications – Towards non-enzymatic glucose detection
PublikacjaRecently, metal nanostructures evoke much interest due to application potential in highly sensitive detectors in biochemistry and medical diagnostics. In this work we report on preparation and characteristics of thin (1–100 nm) Au films deposited onto highly ordered structured titanium templates for SERS (Surface Enhanced Raman Spectroscopy) and electrochemical sensing. The Ti templates are formed by selective removal of TiO2 nanotubes...
-
Flow boiling intensification in minichannels by means of mechanical flow turbulising inserts
PublikacjaThe work presents the results of experimental investigation on heat transfer in minichannels. Refrigerant R123 was used as a test fluid. Single vertical silver tubes of 380 mm length and 2.3 mm diameter were examined with two variants of turbulising inserts. A wide range of parameters was considered, namely mass flux G=534-3011 kg/(m2s), heat flux qw=28.5-68.4 kW/m2, saturation temperature Tsat=23-86 stC and the full range of vapour...
-
Polymer journal bearings behaviour research under limited lubrication and cooling conditions conducted on high torque test rig
PublikacjaPolymer journal bearings are frequently used as a water-lubricated bearings of small marine units’ propeller shafts . Choice of these bearings is based on their simple construction and relatively low purchase and maintenance costs. Although properly designed and installed water lubricated bearings may well last for over a decade, rapid wear or failure of these bearings can be observed...
-
Effect of Particle Size of Fly Ash Microspheres (FAMs) on the Selected Properties of Concrete
PublikacjaThis paper presents the investigations of selected properties of concrete containing two fractions of fly ash microspheres (FAMs) with grain size up to 200 μm and up to 500 μm. Concrete mixtures with ordinary Portland cement and three substitution rates of cement by FAMs, 1.3%, 2.0%, and 2.6%, were investigated. For all concrete mixes, the constant water–binder ratio (w/b) equal to 0.50 was used. The research program included the...
-
Magnetically sensitive fiber probe with nitrogen-vacancy center nanodiamonds integrated in a suspended core
PublikacjaEfficient collection of photoluminescence arising from spin dynamics of nitrogen vacancy (NV) centers in diamond is important for practical applications involving precise magnetic field or temperature mapping. These goals may be realized by the integration of nanodiamond particles with optical fibers and volumetric doping of the particles alongside the fiber core. That approach combines the advantages of robust axial fixation of...
-
Volumetric incorporation of NV diamond emitters in nanostructured F2 glass magneto-optical fiber probes
PublikacjaIntegration of optically-active diamond particles with glass fibers is a powerful method of scaling diamond's magnetic sensing functionality. We propose a novel approach for the integration of diamond particles containing nitrogen-vacancy centers directly into the fiber core. The core is fabricated by stacking the preform from 790 soft glass canes, drawn from a single rod dip-coated with submicron diamond particles suspended in...
-
Antibacterial properties of laser-encapsulated titanium oxide nanotubes decorated with nanosilver and covered with chitosan/Eudragit polymers
PublikacjaTo provide antibacterial properties, the titanium samples were subjected to electrochemical oxidation in the fluoride-containing diethylene glycol-based electrolyte to create a titanium oxide nanotubular surface. Afterward, the surface was covered by sputtering with silver 5 nm film, and the tops of the nanotubes were capped using laser treatment, resulting in an appearance of silver nanoparticles (AgNPs) of around 30 nm in diameter...
-
Effect of the Cavitation Generation Unit Structure on the Performance of an Advanced Hydrodynamic Cavitation Reactor for Process Intensifications
PublikacjaThe advanced rotational hydrodynamic cavitation reactors (ARHCRs) that appeared recently have shown obvious advantages compared with conventional devices in process intensifications. In ARHCRs, the cavitation generation unit (CGU) located on the rotor and stator basically determines their performance. For the first time, the present study investigated the effect of the CGU structure on the performance of a representative ARHCR...
-
Studies of the separation performance of silanized silica gel for simulated distillation
PublikacjaWe present the results of investigations of the chromatographic (sorptive) properties of silanized silica gel as a stationary phase for gas chromatography used for simulated distillation. Commercially available silanized sorbent (particle diameter range 63–200 m, average pore size 60 Å) was sieved to obtain the 80–100 mesh fraction (180–150 m). The obtained results revealed that silanized silica gel allows the complete separation...
-
Comparison of various flow maldistribution quantification methods in mini heat exchangers
PublikacjaThe aim of study is to compare various flow maldistribution quantification methods, using velocity, mass flow rate, pressure, and temperature. An experimentally validated numerical study has been prepared and a heat exchanger with 34 semi-circular channels with a diameter of 3.1 mm has been tested. The minichannels were heated from the bottom with a heat flux of 50, 60, 70, and 80 kW/m2. The cases for various inlet velocities of...
-
Oxygen vacancy-enriched V2O5·nH2O nanofibers ink for universal substrates-tolerant and multi means-integratable NH3 sensing
PublikacjaUniversal substrates-tolerant and multi means-integratable ammonia (NH3) sensing is highly desired in future Internet of Things in environmental monitoring, food security and early diagnosis of human diseases, however, is still less than satisfactory. Here, an oxygen vacancy-governed NH3 sensing has been developed with V2O5·nH2O nanofibers (NFs) ink, via combined thermal decomposition of ammonium metavanadate and dilution. As-obtained...
-
Experimental and numerical investigation on shell and coil storage unit with biodegradable PCM for modular thermal battery applications
PublikacjaThermal energy storage (TES) in automotive applications is currently growing in importance. TES can visibly reduce primary energy consumptions, decrease CO2 emission, and improve thermal comfort in electric as well as hybrid vehicles. However, to meet the new ambitious target (15% reduction of CO2 emissions in the new cars until 2025) it is required to use plug-in electric vehicles. For this reason, this paper focuses on the optimization...
-
Bricks images dataset
Dane BadawczeThe set contains 200 images of various wooden bricks of various shapes and colors placed on a background (blanket) with some heart shaped patterns. Each photo is available in 300x300 and 224x224 pixels size in PNG format. Photos are divided in 10 classes – 8 types of bricks photographed form various angles + 2 additional classes (multiple bricks at...
-
Nanostructuring of thin Au films deposited on ordered Ti templates for applications in SERS
PublikacjaIn this work the results on thermal nanostructuring of the Au films on Ti templates as well as morphology and optical properties of the obtained structures are reported. The bimetal nanostructures are fabricated in a multi-step process. First, the titania nanotubes are produced on the surface of Ti foil by anodization in an ethylene glycol-water solution containing fluoride ions. This is followed by chemical etching in oxalic acid...
-
Design and computational fluid dynamics analysis of the last stage of innovative gas-steam turbine
PublikacjaResearch regarding blade design and analysis of flow has been attracting interest for over a century. Meanwhile new concepts and design approaches were created and improved. Advancements in information technologies allowed to introduce computational fluid dynamics and computational flow mechanics. Currently a combination of mentioned methods is used for the design of turbine blades. These methods enabled us to improve flow efficiency...
-
High-performance NdSrCo2O5+δ–Ce0.8Gd0.2O2-δ composite cathodes for electrolyte-supported microtubular solid oxide fuel cells
PublikacjaNdSrCo2O5+δ (NSCO) is a perovskite with an electrical conductivity of 1551.3 S cm−1 at 500 °C and 921.7 S cm−1 at 800 °C and has a metal-like temperature dependence. This perovskite is used as the cathode material for Ce0.8Gd0.2O2-δ (GDC)-supported microtubular solid oxide fuel cells (MT-SOFCs). The MT-SOFCs fabricated in this study consist of a bilayer anode, comprising a NiO–GDC composite layer and a NiO layer, and a NSCO–GDC...
-
Design and investigations of a micro-turbine flow part
Publikacja-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The heat output of the plant was assumed equal to 20 kW, while the electric output amounted to about 3kW.In the paper a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of the particular experimental investigations and numerical calculations are shown,...
-
Surface Texture after Turning for Various Workpiece Rigidities
PublikacjaIn the paper, we present an analysis of the surface texture of turned parts with L/D (length/diameter) ratios of 6 and 12 and various rigidity values. The studies were carried out on samples made of S355JR steel and AISI 304 stainless steel. A detailed analysis of 2D surface profiles was carried out by using a large number of parameters that allowed us to distinguish significant differences in the surface microgeometry, which confirmed...
-
EFFECT OF SURFACE STATE AND STRESS ON AN OXIDATION OF THE ZIRCALOY-2 ALLOY
PublikacjaZr alloys are widely used as materials for nuclear fuel pellets in the nuclear industry. In the case of the LOCA or RIA happen, a temperature may locally reach high values. Even if the high temperature maintains shortly, the zirconium oxides may become permeable, absorb hydrogen appearing in cooling water from decomposition reaction and crack because of formation and brittle failure of hydrides. Such model cannot so far take into...
-
Field Calibration of Low-Cost Particulate Matter Sensors Using Artificial Neural Networks and Affine Response Correction
PublikacjaDue to detrimental effects of atmospheric particulate matter (PM), its accurate monitoring is of paramount importance, especially in densely populated urban areas. However, precise measurement of PM levels requires expensive and sophisticated equipment. Although low-cost alternatives are gaining popularity, their reliability is questionable, attributed to sensitivity to environmental conditions, inherent instability, and manufacturing...
-
Impact of steel grade on a ship colliding with an offshore wind turbine monopile supporting structure
PublikacjaOffshore wind power is experiencing rapid development around the world. The number of installations and their size is growing. Thousands of monopile support structures with diameters of 10 m and weights of 2000 tons will be installed in the coming years. Offshore wind power installations, often located close to the shore and shipping routes, pose a new challenge to ship safety. The study analyses the damages from an accidental...
-
Accurate Lightweight Calibration Methods for Mobile Low-Cost Particulate Matter Sensors
PublikacjaMonitoring air pollution is a critical step towards improving public health, particularly when it comes to identifying the primary air pollutants that can have an impact on human health. Among these pollutants, particulate matter (PM) with a diameter of up to 2.5 μ m (or PM2.5) is of particular concern, making it important to continuously and accurately monitor pollution related to PM. The emergence of mobile low-cost PM sensors...
-
Experimental study of the impact of notches and holes made in the front edge of adherends on the properties of static and fatigue strength of adhesive joints
PublikacjaThe paper presents the results of experimental studies aimed at determining the effect of holes and notches at the front edge of adherends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets joined with Araldite 2014-2 epoxy adhesive were tested. Comparative tests of static strength in the shear test as well as high-cycle fatigue strength tests were carried out. Joints with three holes with a diameter...
-
TiO 2 Co x O y composite nanotube arrays via one step electrochemical anodization for visible light–induced photocatalytic reaction
PublikacjaTiO2CoxOy (x = 1, y = 1 or x = 3, y = 4) composite photocatalysts have been synthesized via one step anodic anodization of TiCo alloys. The effects of the cobalt content in the alloy (5, 10 and 15 wt%), water content (2, 5 and 10%) in the electrolyte solution, and applied voltage (30, 40 and 50 V) during the anodization process on the morphology and surface properties. Additionally, the dependence of cobalt content in the nanotubes...
-
The effect of imidazolium ionic liquid on the morphology of Pt nanoparticles deposited on the surface of SrTiO3 and photoactivity of Pt–SrTiO3 composite in the H2 generation reaction
PublikacjaPhotocatalytic water splitting has great potential in solar-hydrogen production as a low-cost and environmentally friendly method. Different unique techniques used to obtain photocatalysts with various modifications to improve H2 generation have been introduced. In the present work, SrTiO3 was successfully synthesized via the solvothermal method in the presence of ionic liquid (IL) - 1-butyl-3-methylimidazolium bromide ([BMIM][Br])...
-
A Proposed Soft Computing Model for Ultimate Strength Estimation of FRP-Confined Concrete Cylinders
PublikacjaIn this paper, the feed-forward backpropagation neural network (FFBPNN) is used to propose a new formulation for predicting the compressive strength of fiber-reinforced polymer (FRP)-confined concrete cylinders. A set of experimental data has been considered in the analysis. The data include information about the dimensions of the concrete cylinders (diameter, length) and the total thickness of FRP layers, unconfined ultimate concrete...
-
Effect of irradiation intensity and initial pollutant concentration on gas phase photocatalytic activity of TiO2 nanotube arrays
PublikacjaWell-organized TiO2 nanotube arrays were fabricated via one-step anodization process. The as-prepared TiO2 nanotubes were characterized by X-ray powder diffractometry (XRD), X-ray photoelectron spectroscopy (XPS), diffuse reflectance spectroscopy (DRS) and scanning electron microscopy (SEM). Photocatalytic activity of obtained photocatalyst was studied in reaction of toluene degradation in the gas phase using low powered and low...
-
Safety and efficacy of a Ventralight ST echo ps implant for a laparoscopic ventral hernia repair – a prospective cohort study with a one-year follow-up
Publikacjaing new products Thus, every mesh prior to introduction in clinical settings should be tested with a dedicated tacker to discover the proper fixation algorithm. The aim of the study was to assess the safety and efficacy of the Ventralight ST implant with an ECHO positioning system and a dedicated fixation device, the SorbaFix stapler, in a prospective cohort of patients. Material and methods. The study was a prospective single...
-
Pool boiling of nanofluids on rough and porous coated tubes: experimental and correlation
PublikacjaThe paper deals with pool boiling of water-Al2O3 and water- Cu nanofluids on rough and porous coated horizontal tubes. Commercially available stainless steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate the test heater. The tube surface was roughed with emery paper 360 or polished with abrasive compound. Aluminium porous coatings of 0.15 mm thick with porosity of about 40% were produced by...
-
Modeling of Cardiac Component of Subarachnoid Space Changes in Apnoea Resulting as a Function of Blood Pressure and Blood Flow Parameters - Two Mechanizm of Regulation
PublikacjaExperiments were performed in a group of 19 healthy, non-smoking volunteers. The experiment consisted of three apnoeas, sequentially: 30 s apnoea, 60 s apnoea and maximal, that could be done, apnoea. The breath-hold was separated for 5 minutes rest. The following parameters were measured and obtained for further analysis: blood parameters, artery diameter of the internal carotid artery, end-tidal CO2 in expired air, the cardiac...
-
Research on water lubricated main shaft bearings in conditions of improper lubrication and cooling conducted on high torque real-life scale bush test rig
PublikacjaWater lubricated polymer bushes find increasingly popular use in the sliding bearings of marine propellers, water turbines and pump shafts. Such popularity is partly due to their simple construction which also means relatively affordable price. In addition, properly designed and installed water lubricated bearings may well last for over a decade. However, in practical experience one may also observe cases of rapid wear...
-
EVALUATION OF EFFECTIVENESS OF WATERJET PROPULSOR FOR A SMALL UNDERWATER VEHICLE
PublikacjaT he goal of the project described is to replace the existing propulsion system of a small underwater vehicle with a solution less prone to mechanical damage and ensuring a lower risk of the entanglement of fibrous objects suspended in the body of water. Four typical marine screws are utilised in the current design of the vehicle. One possible solution of the problem is the application of waterjet propulsors located...
-
Multi-objective optimization of the cavitation generation unit structure of an advanced rotational hydrodynamic cavitation reactor
PublikacjaHydrodynamic cavitation (HC) has been widely considered a promising technique for industrial-scale process intensifications. The effectiveness of HC is determined by the performance of hydrodynamic cavitation reactors (HCRs). The advanced rotational HCRs (ARHCRs) proposed recently have shown superior performance in various applications, while the research on the structural optimization is still absent. The present study, for the...
-
Modeling of lapping plate wear and conditioning in single-sided lapping
PublikacjaIn order to achieve higher quality on worked surfaces with lower roughness, very high accuracy of shape and dimensions it is crucial to improve conventional finishing technologies and to develop new working principles. Single-sided lapping is one of the most effective planarization technologies and it is determined by a number of factors and boundary conditions. The most significant influence over a dimensional and profile accuracy,...
-
Rapid development of the photoresponse and oxygen evolution of TiO2 nanotubes sputtered with Cr thin films realized via laser annealing
PublikacjaRecently, earth abundant transition metal oxides have gained particular attention as potential catalyst candidates due to their availability and low-cost comparing to substrates containing precious Pt or Au species. Herein, we present characterization of morphology, structure and electrochemical properties of pulsed 532 nm laser treated TiO2 nanotubes (NT) sputtered by the thin film of chromium. Scanning electron microscopy enables...
-
Damage Detection in the Wind Turbine Blade Using Root Mean Square and Experimental Modal Parameters
PublikacjaThe paper presents results of an experimental study related to a non-destructive diagnostic technique used for preliminary determination the location and size of delamination in composite coatings of wind turbine blades. The proposed method of damage detection is based on the analysis of the ten first mode shapes of bending vibrations, which correspond to displacements of rotor blades perpendicular to the rotor plane. Modal parameters...
-
Natural convective heat transfer from isothermal cuboids
PublikacjaThe paper presents results of theoretical and experimental investigations of the convective heat transfer from isothermal cuboid. The analytical solution was performed taking into account complete boundary layer length and the manner of its propagation around isothermal cuboid. It arises at horizontal bottom surface and grows on vertical lateral surface of the block. After changing its direction, the boundary layer occurs above...
-
The influence of small intestinal mucus structure on particle transport ex vivo
PublikacjaMucus provides a barrier to bacteria and toxins while allowing nutrient absorption and waste transport. Unlike colonic mucus, small intestinal mucus structure is poorly understood. This study aimed to provide evidence for a continuous, structured mucus layer and assess the diffusion of different sized particles through it. Mucus structure was assessed by histology and immunohistochemistry. Ultra-structure was assessed by scanning...
-
Chlorine-free extraction and structural characterization of cellulose nanofibers from waste husk of millet (Pennisetum glaucum)
PublikacjaThis study aims to extract cellulose nanofibers (CNFs) from a sustainable source, i.e. millet husk, which is an agro-waste worthy of consideration. Pre-treatments such as mercerisation, steam explosion, and peroxide bleaching (chlorine-free) were applied for the removal of non-cellulosic components. The bleached millet husk pulp was subjected to acid hydrolysis (5% oxalic acid) followed by homogenization to extract CNFs. The extracted...
-
Generalization of Phylogenetic Matching Metrics with Experimental Tests of Practical Advantages
PublikacjaThe ability to quantify a dissimilarity of different phylogenetic trees is required in various types of phylogenetic studies, for example, such metrics are used to assess the quality of phylogeny construction methods and to define optimization criteria in supertree building algorithms. In this article, starting from the already described concept of matching metrics, we define three new metrics for rooted phylogenetic trees. One...
-
Measurement of mass flow of viscous liquid through a Cylindrical Orifice under laminar flow (CylOr)
Dane BadawczeThe data was obtained as part of the project "Measurement of mass flow of viscous liquid through a Cylindrical Orifice under laminar flow (CylOr)", in which flow tests of hydraulic oil through a cylindrical orifice with a thickness of l = 25 mm and a throat b = 0.5 (diameter pipes D = 50 mm, orifice diameter d = 25 mm) on the test stand at the Department...
-
Simulation of ship turning circle test for ballast and full load conditions
Dane BadawczeThe data show the results of the turning circle spiral test for the simplified ship model, taking into account two states of loading: ballast and full load. During the circulation test, the manoeuvrability of the vessel is tested.
-
Implementation of Non-Probabilistic Methods for Stability Analysis of Nonlocal Beam with Structural Uncertainties
PublikacjaIn this study, a non-probabilistic approach based Navier’s Method (NM) and Galerkin Weighted Residual Method (GWRM) in term of double parametric form has been proposed to investigate the buckling behavior of Euler-Bernoulli nonlocal beam under the framework of the Eringen's nonlocal elasticity theory, considering the structural parameters as imprecise or uncertain. The uncertainties in Young’s modulus and diameter of the beam are...
-
Waveguide model of the hearing aid earmold system
PublikacjaBackground The earmold system of the Behind-The-Ear hearing aid is an acoustic system that modifies the spectrum of the propagated sound waves. Improper selection of the earmold system may result in deterioration of sound quality and speech intelligibility. Computer modeling methods may be useful in the process of hearing aid fitting, allowing physician to examine various earmold system configurations and choose the optimum one...
-
Waveguide model of the hearing aid earmold system
PublikacjaBackground The earmold system of the Behind-The-Ear hearing aid is an acoustic system that modifies the spectrum of the propagated sound waves. Improper selection of the earmold system may result in deterioration of sound quality and speech intelligibility. Computer modeling methods may be useful in the process of hearing aid fitting, allowing physician to examine various earmold system configurations and choose the optimum one...