Wyniki wyszukiwania dla: au-cu%20nanostructures
-
INFLUENCE OF SURFACE CURVATURE ON SESSILE DROPLET CONTACT ANGLE OF NANOFLUIDS
PublikacjaThis paper deals with change in contact angle of droplets of three nanofluids, i.e. water-Al2O3, water-TiO2 and water-Cu. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight. Although dispersants were not used to stabilize the suspension, the solutions tested exhibited satisfactory stability. Ultrasonic vibration was used in order to stabilise the dispersion of the nanoparticles. Experimental measurements...
-
In situ transformation boosts the pseudocapacitance of CuNi-MOF via cooperative orientational and electronic governing
PublikacjaThe disordered arrangement and thereof inferior conductivity of 2D MOF sheets seriously hinder their practical application. Herein, we propose in situ transformation strategy to architect vertically oriented bimetallic CuNi-MOF as a self-supporting electrode, leading to a decuple high specific capacitance of 1262 C g-1 in comparison with the pristine Ni-MOF powder of 114 C g-1 at 2 A g-1. DFT calculations reveal that introduction...
-
Zrozumienie mechanizmów krzepnięcia i rozpuszczalności miedzi w aluminium w celu poprawy właściowości stopów Al-Cu
ProjektyProjekt realizowany w Wydział Fizyki Technicznej i Matematyki Stosowanej zgodnie z porozumieniem 0439/IP/2013/72 z dnia 2013-07-02
-
Ryszard Andruszkiewicz prof. dr hab. inż.
Osoby -
AfroTrans Rozwój transportu w Afryce Subsaharyjskiej - nowoczesny program studiów magisterskich oraz współpraca pomiędzy uczelniami
ProjektyProjekt realizowany w Katedra Inżynierii Transportowej
-
Calix[4]arene-Thioamides as Ionophores for Transition and Heavy Metal cations
PublikacjaCalix[4]arene derivatives play an important role as sensing materials in Ion Selective Electrodes(ISEs). Nowadays a high impact is put to control in natural waters the level of toxic heavy metals, like Pb ,Cd, Hg or Cu which may cause the great risk to human health. Our goal was to design and to synthesize ligands possessing ability to bind transition and heavy metal cations. The synthesis, crystal structures,extractive and ionophoric...
-
An inclination in Thermal Energy Using Nanoparticles with Casson Liquid Past an Expanding Porous Surface
PublikacjaPhysical aspects of inclined MHD nanofluid towards a stretching sheet embedded in a porous medium are visualized. Two types of nanoparticles are used named as copper and alumna dioxide with water as base fluid. Similarity transformations are used to convert the partial differential equations into the set of ordinary differential equation. Closed solutions are found to examine the velocity and the temperature profiles. It is examined...
-
Computational fluid dynamics simulation of heat transfer from densely packed gold nanoparticles to isotropic media
PublikacjaThis work aims to determine and compare heat generation and propagation of densely packed gold nanoparticles (Au NPs) induced by a resonant laser beam (532 nm) according to the Mie theory. The heat flux propagation is transferred into the materials, which here are: silica glass; soda-lime-silica glass; borosilicate glass; polymethyl methacrylate (PMMA); polycarbonate (PC); and polydimetylosiloxane (PDMS). This analysis aims to...
-
A modern solid waste management strategy – the generation of new by-products
PublikacjaTo benefit the environment and society, EU legislation has introduced a ‘zero waste’ strategy, in which waste material should be converted to resources. Such legislation is supported by the solid waste hierarchy concept, which is a set of priorities in waste management. Under this concept, municipal solid waste plants (MSWPs) should be equipped with sorting and recycling facilities, composting/incineration units and landfill prisms...
-
Anthropogenic trace metals in Setiu Wetland: Spatial and seasonal distribution and implications for environmental health
PublikacjaThe growing urban wastewater volume poses a major global environmental challenge, especially in developing nations where inadequate treatment and discharge impact clean water availability. This study focused on Setiu Wetland, aiming to analyze seasonal and spatial variations of trace metals in particulate form from anthropogenic and pathogenic sources. Surface water samples were collected from multiple stations, measuring physical...
-
Ways of Harmonising Polish Competition Law with the Competition Law of the EU
PublikacjaThis article discusses the harmonisation of laws within the EU focusing on the specific ways of achieving an approximation of the Polish legal system with European competition law. It identifies and gives an overview of three specific ways of harmonising national laws with EU antitrust provisions: (1) spontaneous (or bottom-up) harmonisation; (2) judicial harmonisation and; (3) legislative harmonisation by means of EU Directives....
-
Atmospheric heavy metal deposition accumulated in rural forest soils of southern Scandinavia
PublikacjaPrzeprowadzono obliczenia zakumulowanej ( w okresie 50 lat) atmosferycznej depozycji metali ciężkich na glebach leśnych na obszarach wiejskich. Podstawę do obliczeń stanowiły:- pomiary zawartości metali ciężkich w opadach atmosferycznych (przeprowadzone przez okres 33 lat) na terenie Danii,- europejska baza danych o emisji zanieczyszczeń.Oznaczano zawartość metali ciężkich (Pb, Cd, Cu, Zn, V, Ni, As) w próbkach opadów atmosferycznych...
-
Lower rim substituted tert-Butylcalix[4]arenes. Part 13. Interaction of calix-hydroxamates with Fe(III) and Pb(II); studies in ion-selective membrane electrodes (ISE)
PublikacjaPrzedmiotem pracy są badania oddziaływań pomiędzy trzema wybranymi hydroksamowymi pochodnymi t-butylo-kaliks[4]arenu i jonami metali z wykorzystaniem membranowych elektrod jonoselektywnych (ISE). Elektrody zawierające jako materiał aktywny wymienione związki jonoforowe charakteryzują się nernstowskim nachyleniem i szerokim zakresem liniowości na jony Pb(II), a także dobrą selektywnością na jony Pb(II)w stosunku do jonów UO2(II),...
-
Calix[4]arene-Thioamides as Ionophores for Transition and Heavy Metal Cations.
PublikacjaPochodne kaliks[4]arenów odgrywają ważną rolę jako materiał aktywny w membranowych elektrodach jonoselektywnych. Obecnie duży nacisk kładzie się na kontrolę stężeń kationów metali ciężkich, takich jak Pb, Cd, Hg, Cu w wodach naturalnych. Naszym zadaniem było zaprojektować i zsyntezować ligandy, które wykazują zdolność do wiązania kationów metali ciężkich i przejściowych. Synteza, struktury krystaliczne, ekstrakcja i właściwości...
-
Experimental study of pressure rise at the evaporator of capillary pumped loop with acetone and water as working fluids
PublikacjaIn this work studied is the possibility of fluid pumping using capillary forces in the capillary pumped loop. Experimental and theoretical studies have been performed to understand the phenomena associated with heat transfer in porous structure of the evaporator. The capillary effect was studied during operation of two different capillary porous structures with two different working fluids, namely water and acetone. The results...
-
NOx Photooxidation over Different Noble Metals Modified TiO2
PublikacjaWe compared the activity enhancement effect of noble metal deposited on TiO2 in photocatalytic nitrogen oxides oxidation. Titanium dioxide was decorated with Ag, Au, Pt or Pd in the sol-gel process. Synthesized catalysts were characterized by X-ray diffraction (XRD), Brunauer–Emmett–Teller measurement (BET), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM) and energy dispersive X-ray analysis (EDX)....
-
Experimental tuning of AuAg nanoalloy plasmon resonances assisted by machine learning method
PublikacjaPlasmonic nanostructures based on AuAg nanoalloys were fabricated by thermal annealing of metallic films in an argon atmosphere. The nanoalloys were chosen because they can extend the wavelength range in which plasmon resonance occurs and thus allow the design of plasmonic platforms with the desired parameters. The influence of initial fabrication parameters and experimental conditions on the formation of nanostructures was investigated....
-
Heavy metal accumulation and distribution in Phragmites australis seedlings tissues originating from natural and urban catchment
PublikacjaThe retention of heavy metal (HM) was studied in root and rhizomes (BLG), stems (ST), and leaves (LF) of Phragmites australis (common reed) seedlings collected from different locations, differing in the scale of anthropogenic interference. The analysis includes the reference samples of sediments in uncontaminated lake Garczonki and contaminated roadside ditch in Cieplewo. The concentrations of Zn, Cu, Pb, Cd, Ni, and Cr were analyzed...
-
Trace Metal Contamination of Bottom Sediments: A Review of Assessment Measures and Geochemical Background Determination Methods
PublikacjaThis paper provides an overview of different methods of assessing the trace metal (TM) contamination status of sediments affected by anthropogenic interference. The geochemical background determination methods are also described. A total of 25 papers covering rivers, lakes, and retention tanks sediments in areas subjected to anthropogenic pressure from the last three years (2019, 2020, and 2021) were analysed to support our examination...
-
Synthesis, single crystal growth and properties of Sr5Pb3ZnO12
PublikacjaAbstract The novel Sr5Pb3ZnO12 oxide was synthesized by the solid-state reaction method. The crystal structure was studied by means of the powder x-ray diffraction Rietveld method and was found to be similar to 3 other previously known Sr5Pb3MO12 compounds (M = Co, Ni, Cu). Crystals of several hundred microns in size of the new phase were grown in molten sodium chloride and imaged using confocal optical and scanning electron microscopy....
-
Intermetallic disordered magnet Gd2Pt1.1Ge2.9 and its relation to other AlB2 -type compounds
PublikacjaThe intermetallic germanide Gd 2 Pt 1.1 Ge 2.9 was synthesized using an arc-melting method. The crystal structure was characterized using powder x-ray diffraction, revealing a disordered ternary AlB 2 -type structure (space group P 6 / m m m , No. 191) with lattice parameters a = 4.2092 ( 1 ) Å and c = 4.0546 ( 2 ) Å . Physical properties were investigated by magnetic susceptibility and heat capacity measurements, which...
-
Visible light activity of pulsed layer deposited BiVO4/MnO2 films decorated with gold nanoparticles: The evidence for hydroxyl radicals formation
PublikacjaThin films containing BiVO4 and MnO2 deposited on FTO and modified by Au nanoparticles were studied towards their photoelectrochemical and photocatalytical activities in an aqueous electrolyte. Electrodes were prepared by the pulsed laser deposition (PLD) method. The surfactant-free ablation process was used for preparation of the gold nanoparticles (GNP) water suspension. Obtained layers of varied thicknesses (27–115 nm) were...
-
Annealing Rate as a Crucial Parameter Controlling the Photoelectrochemical Properties of AuCu Mosaic Core–Shell Nanoparticles
PublikacjaThermal processing is an essential step during the synthesis of various metal nanostructures and for tailoring their morphology, optical, and electrochemical properties. Herein, a profound impact of the annealing rate and time on photoactivity of gold–copper nanostructures by changes in the position and alignment of energy levels and surface states is reported. AuCu nanoparticles (NPs) are fabricated by sputtering of thin metal...
-
Metal complexes with mixed s-donor ligands - a route via silanethiolates
PublikacjaW ramach prezentowanej pracy przedstawiono pierwsze próby syntezy mieszanych układów zawierających jednocześnie przykoordynowane reszty ditiokarbaminianową oraz silanotiolanowych. W badaniach posłużono się - jako substratami tri-tert-butoksysilanotiolanami kompleksami Cd, Zn, Cu, Pb, Hg, Ag i Co, a także solami kwasów: dietyloditiokarbaminowego oraz pirolidynoditiokarbaminowego. W przypadku związku Ag nie udało się wyizolować stałych...
-
Selectivity of Pb(II) transport across polymer inclusion membranes doped with imidazole azothiacrown ethers
PublikacjaMembrany wykonane z trioctanu celulozy zawierające jako jonofor 18 i 21-członowe azotiakorony z resztą imidazolu w makropierścieniu przebadano pod kątem transportu jonów Zn(II), Cd(II) i Pb(II) z wodnego roztworu soli (pH ~5.5, cMe = 0,001 M). W wyniku badań ustalono, że jon Pb(II) może być efektywnie wydzielony z roztworu mieszaniny jonów Pb(II), Zn(II), Co(II), Ni(II), Cu(II) i Cd(II).Sekwencja selektywności transportu dla 18-członowej...
-
Copper-based 2D-coordination polymer as catalyst for allylation of aldehydes
PublikacjaA copper-tartrate, [Cu2(Tart)2(H2O)2]·4H2O, was synthesized at room temperature in aqueous media using copper chloride and D-tartaric acid. The compound crystallizes in the monoclinic system P21 space group and was characterized by infrared spectroscopy, thermogravimetry, X-ray powder diffraction and the results are in good agreement with the single crystal...
-
Structural and catalytic properties of ceria layers doped with transition metals for SOFCs fueled by biogas
PublikacjaThe aim of this paper was to investigate an influence of the nanocrystalline Ce0.8A0.2O2-δ (A = Mn, Fe, Co, Ni, Cu) materials on the direct internal reforming of biogas in SOFC. Structural analysis of fabricated compounds has been done. An in-situ analysis of a composition of outlet gases from operating SOFC was performed using FTIR spectroscopy with simultaneous electrical tests. It was found out, that type of dopant strongly...
-
Preparation and characterisation of iron substituted Mn1.7Cu1.3-xFexO4 spinel oxides (x = 0, 0.1, 0.3, 0.5)
PublikacjaSpinel oxides with the general formula Mn1.7Cu1.3-xFexO4 (x= 0, 0.1, 0.3, 0.5) were prepared and evaluated in this work for their properties at high temperatures. The effect of partially substituting Cu by Fe has not been studied so far for this group of materials and is thus evaluated in this work. Mn1.7Cu1.3-xFexO4 powders were synthesised by a soft chemistry process and studied in terms of crystallographic phase analysis, electrical...
-
Sustainable energy system combined biogas-feedSolid Oxide Fuel Cell and Microalgae technology
PublikacjaIn the new frontier of energy and environmental safety, new efficient and clean safe energy conversion systems are required. In this sense, the present work is framed within the context of Circular Economy and proposes a multidisciplinary study for the development of more efficient, economically viable and non-polluting energy conversion systems, based on the synergetic combination of different technologies: fuel cells, biofuels,...
-
Burnout Investigation of Small Diameter Tubes Immersed in Nanofluids
PublikacjaThis paper deals with research into pool boiling critical heat flux (CHF) of water–Al2O3, water–TiO2 and water–Cu nanofluids on horizontal stainless steel tubes. The experiments were conducted under atmospheric pressure. Nanoparticles were tested at concentrations of 0.001%, 0.01%, 0.1% and 1% by weight. Ultrasonic vibration was used in order to stabilize the dispersion of the nanoparticles. Although dispersants were not used to...
-
Exploring multi-step glucose oxidation kinetics at GOx-functionalized nanotextured gold surfaces with differential impedimetric technique
PublikacjaFor a few past years, we can observe the enormous growth of investigations related to ultrasensitive electrochemical sensors capable of reliable determination of important body parameters and analytes. Utilized procedures rely on standard electrochemical methods, demanding electrode polarization, and information about the initial characteristics of the working electrode. More and more complex electrode materials are characterized...
-
Spinele w układzie Cu-Mn-(Fe,Ni,Zn,Cr)-O: synteza, badania struktury, właściwości fizykochemicznych i aktywności elektrokatalitycznej operando
ProjektyProjekt realizowany w Katedra Inżynierii Materiałów Funkcjonalnych WETI zgodnie z porozumieniem UMO-2022/45/N/ST5/03627 z dnia 2023-01-17
-
Simple synthesis route for fabrication of protective photo‐crosslinked poly(zwitterionic) membranes for application in non‐enzymatic glucose sensing
PublikacjaThis work focuses on the fabrication of non-enzymatic glucose sensing materials based on laser-formed Au nanoparticles embedded in Ti-textured substrates. Those materials possess good catalytic activity toward glucose oxidation in 0.1 × phosphate buffered saline as well as resistance to some interferants, such as ascorbic acid, urea, and glycine. The electrodes are further coated with three different polymers, that is, Nafion,...
-
Ultrasensitive electrochemical determination of the cancer biomarker protein sPD-L1 based on a BMS-8-modified gold electrode
PublikacjaThis work describes the modification of a gold electrode with the BMS-8 compound that interacts with the Programmed Death-Ligand 1 (PD-L1), an immune checkpoint protein. The results show that we can confirm the presence of the sPD-L1 in the concentration range of 10−18 to 10−8 M using electrochemical impedance spectroscopy (EIS) with a limit of detection (LOD) of 1.87 × 10−14 M for PD-L1 (S/N = 3.3) and at a concentration of 10−14...
-
Rapid development of the photoresponse and oxygen evolution of TiO2 nanotubes sputtered with Cr thin films realized via laser annealing
PublikacjaRecently, earth abundant transition metal oxides have gained particular attention as potential catalyst candidates due to their availability and low-cost comparing to substrates containing precious Pt or Au species. Herein, we present characterization of morphology, structure and electrochemical properties of pulsed 532 nm laser treated TiO2 nanotubes (NT) sputtered by the thin film of chromium. Scanning electron microscopy enables...
-
The quality of sewage sludge stabilized for a long time in reed basins
PublikacjaThe aim of the work was to determine changes of long-term sewage sludge quality stabilized in reed basins from 7-15 years. The following parameters were evaluated: dry matter and organic matter concentration, nitrogen, phosphorus, and selected heavy metal (Cd, Ni, Pb, Cr, Cu, Zn) fractions. The material for the investigations was collected from 4 reed basin systems (utilisated sewage sludge) located in conventional WWTPs in Denmark...
-
Zastosowanie technik chemometrycznych w analityce i monitoringu środowiskowym
PublikacjaW pracy przedstawiono wyniki monitoringu przybrzeżnej strefy Morza Bałtyckiego w rejonie Zatoki Gdańskiej. W projekcie oznaczano związki z grupy WWA, HC, OPNPS, OCP5, VOCl oraz wybrane metale ciężkie (Pb, Zn, Cd, Cu). Podjęto próbę wyjaśnienia występowania określonych grup zanieczyszczeń w próbkach wody morskiej poprzez charakteryzację źródeł zanieczyszczeń wód lądowych, a także dzięki wyjaśnieniu statystycznie istotnych korelacji...
-
Surface sediments pollution due to shipwreck s/s “Stuttgart”: a multidisciplinary approach
PublikacjaShipwrecks may pose a serious source of pollution for marine ecosystems. For this reason, it is of great importance to perform a marine ecosystem risk assessment due to plausible wreck presence. One of elements of such an assessment is determining the state of the environment in the vicinity of the wreck. In the work presented, the results of studies on surface sediments samples collected around the s/s Stuttgart ship sunk during...
-
Cienkie warstwy TiO2: metoda otrzymywania, charakterystyka oraz zastosowania
PublikacjaGłównym celem naukowym badań było lepsze poznanie mechanizmu tworzenia cienkich warstw fotokatalitycznych w postaci nanorurek TiO2 oraz zrozumienie wpływu ich morfologii oraz struktury na aktywność oraz stabilność w procesie fotodegradacji zanieczyszczeń organicznych zarówno w fazie wodnej jak i gazowej. Szczególną uwagę poświęcono syntezie nowych typów fotokatalizatorów w oparciu o matryce nanorurek TiO2 (nanorurki modyfikowane...
-
Ekspertyza numer 75/01/II/2016 - Określenie stanu powierzchni wewnętrznej, rury wykonanej ze stopu CuNi10Fe1,6Mn ze względu na możliwość wystąpienia produktów korozji. Określenie statusu warstwy pasywnej
PublikacjaElementy systemów rurociągów okrętowych mających kontakt z wodą zaburtową, takich jak np. instalacja chłodzenia silnika głównego, czy instalacja przeciw pożarowa, wykonywane są często ze stopów miedzi z nikem zwanych Cuniferami (Cu Ni Fe R-reszta pierwiastków stopowych). Cunifery charakteryzują się bardzo wysoką odpornością na korozję, pod warunkiem że procesy spawania i późniejszej pasywacji rurociągu przebiega zgodnie z właściwymi...
-
Determination of heavy metals in eyeshadows from China
PublikacjaPersonal care products and cosmetics are used daily by many people, causing local exposure to certain chemical substances through the application directly inside the oral cavity, on the skin, lips, eyes, and mucosa. Eyeshadows are among the most commonly used types of cosmetics. According to scientifc reports, they may contain heavy metals, especially in non-original products. The exposure to said heavy metals may cause local skin...
-
Two kinds of oxygen vacancies in lithium titaniate doped with copper as detected by EPR
PublikacjaLithium titanate (Li1+xTi2-xO4) doped with Cu2+ ions was synthesized by sol-gel processing method. The structure and morphology are characterized by X-ray Diffraction (XRD), X-ray Photoemission Spectroscopy (XPS), Scanning Electron Microscopy (SEM) and Electron Paramagnetic Resonance (EPR). Spin Hamiltonian parameters describing Zeeman and hyperfine interaction for 63Cu2+ ions were obtained from EPR spectra simulations. The spectra...
-
Defective TiO2 Core-Shell Magnetic Photocatalyst Modified with Plasmonic Nanoparticles for Visible Light-Induced Photocatalytic Activity
PublikacjaIn the presented work, for the first time, the metal-modified defective titanium(IV) oxide nanoparticles with well-defined titanium vacancies, was successfully obtained. Introducing platinum and copper nanoparticles (NPs) as surface modifiers of defective d-TiO2 significantly increased the photocatalytic activity in both UV-Vis and Vis light ranges. Moreover, metal NPs deposition on the magnetic core allowed for the effective separation...
-
Laser induced formation of copper species over TiO2 nanotubes towards enhanced water splitting performance
PublikacjaWe proposed fast and scalable route where the ordered TiO2 nanotubes coated with thin copper layers were annealed by the laser beam of 355 nm wavelength at different fluencies in the range of 15–120 mJ/cm2. As a result, copper species are integrated with the titania substrate and the formed material exhibits unique optical absorption bands in the visible range. Moreover, X-ray photoelectron spectroscopy analysis reveals the formation...
-
Chemometric Evaluation of WWTPs’ Wastewaters and Receiving Surface Waters in Bulgaria
PublikacjaWastewater treatment plant (WWTP) installations are designed and operated to reduce the quantity of pollutants emitted to surface waters receiving treated wastewaters. In this work, we used classical instrumental studies (to determine chemicals and parameters under obligations put with Directive 91/271/EEC), ecotoxicological tools (Sinapis alba root growth inhibition (SA-RG) and Heterocypris incongruens mortality (MORT) and growth...
-
Mechanical Behavior of Bi-Layer and Dispersion Coatings Composed of Several Nanostructures on Ti Substrate
PublikacjaThree coatings suitable for biomedical applications, including the dispersion coating composed of multi-wall carbon nanotubes (MWCNTs), MWCNTs/TiO2 bi-layer coating, and MWCNTs-Cu dispersion coating, were fabricated by electrophoretic deposition (EPD) on Ti Grade II substrate. Optical microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and nanoindentation were applied to study topography, chemical, and...
-
Distribution and removal efficiency of heavy metals in two constructed wetlands treating landfill leachate
PublikacjaThe results of heavy metals (Fe, Mn, Zn, Ni, Cu, Cr, Pb, Cd) removal and partitioning between aqueous and solid phases at two wetlands (TWs) treating municipal landfill leachates are presented. One of the TWs is a surface flow facility consisting of 10 ponds. The other TW is a newly constructed pilot-scale facility consisting of three beds with alternately vertical and horizontal sub-surface flow. The metals concentrations were...
-
Assessment of metal removal in a surface flow constructed wetland treating landfill leachate
PublikacjaThe study concerns heavy metal retention and transformation processes in a free water surface constructed wetland treating landfill leachate in a temperate climate. The total effectiveness of heavy metals removal in the analyzed CW was evaluated basing on heavy metals inflow and outflow concentrations. The concentrations of eight heavy metals (Fe, Mn, Zn, Pb, Ni, Cu, Cr, Cd) in landfill leachate (LL) and sediments were measured....
-
Influences of grain shape and size distribution on permeability
PublikacjaThe present study investigates the effects of shape and size distributions of grains on the coefficient of permeability (k). A series of constant head permeability tests were performed to characterize the coefficient of permeability. Three particle size ranges (4.75- 0.075, 1.18- 0.075 and 0.300-0.075 mm) of two different sands (Narli Sand, Crushed Stone Sand) having different shapes were tested in a constant head permeability...
-
Ultrasound assisted synthesis of 3-alkynyl substituted 2-chloroquinoxaline derivatives: Their in silico assessment as potential ligands for N-protein of SARS-CoV-2
PublikacjaIn view of recent global pandemic the 3-alkynyl substituted 2-chloroquinoxaline framework has been explored as a potential template for the design of molecules targeting COVID-19. Initial in silico studies of representative compounds to assess their binding affinities via docking into the N-terminal RNA-binding domain (NTD) of N-protein of SARS-CoV-2 prompted further study of these molecules. Thus building of a small library of...