Filtry
wszystkich: 566
wybranych: 501
Wyniki wyszukiwania dla: punching shear
-
NEW EXPERIENCES IN DIKE CONSTRUCTION WITH SOIL-ASH COMPOSITESAND FINE-GRAINED DREDGED MATERIALS
PublikacjaThe supporting structure inside a coastal dike is often made of dredged non-uniform sand with good compaction proper-ties. Due to the shortage of natural construction material for both coastal and river dikes and the surplus of different processed mate-rials, new experiments were made with sand-ash mixtures and fine-grained dredged materials to replace both dike core and dikecover materials resulting in economical, environmentally...
-
Force transfer and stress distribution in short cantilever deep beams loaded throughout the depth with a various reinforcement
PublikacjaDeep beams used as the main reinforced concrete structural elements which taking over the load and stiffening construction are often found in high-rise buildings. The architecture of these buildings is sometimes sophisticated and varied, arouse the admiration of the majority of recipients, and thus causing an engineering challenge to correctly design the structural system and force transfer. In such structures is important to shape...
-
Probabilistic seismic assessment of RC box-girder highway bridges with unequal-height piers subjected to earthquake-induced pounding
PublikacjaThis paper uses the probabilistic seismic assessment to study the effects of pounding and irregularity on the seismic behavior of typical concrete box-girder bridges with four levels of altitudinal irregularity. To extend the results for all bridges in the same class, uncertainty related to the earthquake, structural geometries, and materials are considered. Pounding is likely to take place in two cases: the first one concerns...
-
Management of ground tire rubber waste by incorporation into polyurethane-based composite foams
PublikacjaRapid economic growth implicated the developing multiple industry sectors, including the automotive branch, increasing waste generation since recycling and utilization methods have not been established simultaneously. A very severe threat is the generation of enormous amounts of post-consumer tires considered burdensome waste, e.g., due to the substantial emissions of volatile organic compounds (VOCs). Therefore, it is essential...
-
Development and validation of lumbar spine finite element model
PublikacjaThe functional biomechanics of the lumbar spine have been better understood by finite element method (FEM) simulations. However, there are still areas where the behavior of soft tissues can be better modeled or described in a different way. The purpose of this research is to develop and validate a lumbar spine section intended for biomechanical research. A FE model of the 50th percentile adult male (AM) Total Human Model for Safety...
-
Pounding between high-rise buildings founded on different soil types
PublikacjaEarthquake-induced pounding is a phenomenon that has been often experienced in previous earthquakes. The aim of this study is to investigate the effect of the soil type on high-rise buildings experiencing earthquake induced-pounding. Pounding between 7-storey and 9-storey buildings is examined under five soil types defined in the ASCE 7-10 code which are hard rock, rock, very dense soil and soft rock, stiff soil and soft clay soil....
-
Application of analytical methods for the determination of bioactive compounds in some berries
PublikacjaFluorometry, ESI-MS, FTIR, and radical scavenging assays were used for characterization of bioactive compounds and the levels of their antioxidant activities. Polyphenols, flavonoids, anthocyanins, and ascorbic acid and the level of antioxidant activity of water extracts of “Murtilla-like” [Myrteola nummularia (Poiret) Berg.], and other widely consumed berries were determined and compared. The contents of bioactive compounds and...
-
Analysis of features of stainless steels in dissimilar welded joints in chloride inducted corrosion
PublikacjaStainless steels of femtic-austenitic microstructure that means the duplex Cr-Ni-Mo steels, in comparison with austenitic steel includes less expensive nickel and has much better mechanical properties with good formability and corrosion resistance, even in environments containing chloride ions. Similar share of high chromium ferrite and austenite, which is characterized by high ductility, determines that the duplex steels have...
-
Preliminary results from HEDGEHOG REXUS Project - sounding rocket experiment on accelerations, vibrations and heat flow
PublikacjaAs access to space conditions becomes more available, both technically and economically, scientists' interest in launching finer and more sophisticated experiments grows. This applies now more than ever to fragile by nature biological and chemical experiments. To be qualified for launch, such experiments need to be carefully tested prior to the event. The tests should represent actual launch conditions as closely and in as detailed...
-
Pounding between high-rise buildings with different structural arrangements
PublikacjaEarthquake-induced structural pounding has led to significant damages during previous earthquakes. This paper investigates the effect of pounding on the dynamic response of colliding high-rise buildings with different structural arrangements. Three 3-D buildings are considered in the study, including 5-storey building, 7-storey building and 9-storey building. Three pounding scenarios are also taken into account, i.e. pounding between...
-
On mechanics of piezocomposite shell structures
PublikacjaThis study presents an original and novel investigation into the mechanics of piezo-flexo-magneto-elastic nanocomposite doubly-curved shells (PFMDCSs) and the ability to detect the lower and higher levels of electro-magnetic fields. In this context, by utilizing the first-order shear deformation shell model, stresses and strains are acquired. By imposing Hamilton's principle and the von Kármán approach, the governing equations...
-
Enzymatic cross-linking of β-lactoglobulin in solution and at air–water interface: Structural constraints
PublikacjaEffective and controlled use of cross-linking enzymes in structure engineering of food systems depends on characterization of the favorable conditions for enzyme-substrate complex and the limiting factors for the desired modification. In this respect, we analyzed the susceptibility of bovine β-lactoglobulin (BLG) to enzymatic cross-linking by Trichoderma reesei tyrosinase (TrTyr) and transglutaminase (TG). Changes in BLG molecular...
-
Derecho Evolving from a Mesocyclone—A Study of 11 August 2017 Severe Weather Outbreak in Poland: Event Analysis and High-Resolution Simulation
PublikacjaThis study documents atmospheric conditions, development, and evolution of a severe weather outbreak that occurred on 11 August 2017 in Poland. The emphasis is on analyzing system morphology and highlighting the importance of a mesovortex in producing the most significant wind damages. A derecho-producing mesoscale convective system (MCS) had a remarkable intensity and was one of the most impactful convective storms in the history...
-
Collision Risk-Informed Weather Routing for Sailboats
PublikacjaSelected COLREG rules, good seamanship and sheer common sense indicate that it is in a sailboat's interest to follow collision-free routes without relying on large power-driven ships to give way. Until now, however, no method has integrated a sailboat's weather routing with collision risk monitoring and collision avoidance. Therefore, a new deterministic approach to combine the above features within one method is introduced here....
-
Estimation of nonstructural stiffness in instrumented steel frames
PublikacjaLateral stiffness of nonstructural components may significantly influence the initial stiffness of the entire structure and consequently alter its dynamic characteristics. While methods for simulating structural members are well-established, approaches for modeling nonstructural components that also participate in seismic response are notably less developed. In this paper a simplified, physically-intuitive approach for estimating...
-
Expedited constrained multi-objective aerodynamic shape optimization by means of physics-based surrogates
PublikacjaIn the paper, computationally efficient constrained multi-objective design optimization of transonic airfoil profiles is considered. Our methodology focuses on fixed-lift design aimed at finding the best possible trade-offs between the two objectives: minimization of the drag coefficient and maximization of the pitching moment. The algorithm presented here exploits the surrogate-based optimization principle, variable-fidelity computational...
-
From structure to luminescence investigation of oxyfluoride transparent glasses and glass-ceramics doped with Eu3+/Dy3+ ions
PublikacjaGlasses and glass-ceramics with nominal composition 73 TeO2– 4BaO– 3Bi2O3–18SrF2-2RE2O3 (where RE = Eu, Dy) have been synthesized by conventional melt-quenching technique and subsequent heat treatment at 370 °C for 24 h in air atmosphere. Various Eu3+ to Dy3+ molar ratio have been applied to investigate luminescence properties in both glass and glass-ceramic matrices. Especially, white light emission through simultaneous excitation...
-
Activated sodium percarbonate-ozone (SPC/O3) hybrid hydrodynamic cavitation system for advanced oxidation processes (AOPs) of 1,4-dioxane in water
PublikacjaHydrodynamic cavitation (HC) was employed to activate sodium percarbonate (SPC) and ozone (O3) to degrade recalcitrant 1,4-dioxane. The degradation efficiency > 99 % with a rate constant of 4.04 × 10−2 min−1 was achieved in 120 min under the optimal conditions of cavitation number (Cv) 0.27, pH 5, molar ratio of oxidant to pollutant (rox) 8, ozone dose of 0.86 g h−1 under 25 ± 2 °C with initial concentration of 1,4-dioxane 100...
-
Micro-cracking pattern recognition of hybrid CNTs/GNPs cement pastes under three-point bending loading using acoustic emission technique
PublikacjaThe generation of microcracks has an important influence on the behaviour of concrete structures. In this study, the acoustic emission (AE) technique was used to investigate the fracture phenomena and micro-cracking behavior of hybrid carbon nanotubes (CNTs, the 1-D allotrope of carbon atoms) and graphene nanoplatelets (GNPs, 2D monolayer of sp2-hybridized carbon atoms), cement composites under three-point bending loading. In...
-
Effect of lag screw on stability of first metatarsophalangeal joint arthrodesis with medial plate
PublikacjaBackground: First metatarsophalangeal joint (MTP-1) arthrodesis is a commonly performed procedure in the treatment of disorders of the great toe. Since the incidence of revision after MTP-1 joint arthrodesis is not insignificant, a medial approach with a medially positioned locking plate has been proposed as a new technique. The aim of the study was to investigate the effect of the application of a lag screw on the stability and...
-
The method of analysis of damage reinforced concrete beams using terrestial laser scanning
PublikacjaThe authors present an analysis of the possibility to assess deformations and mechanisms of destructing bent reinforced concrete beams using the terrestrial laser scanning. As part of the experiments carried out at the Regional Laboratory of Construction of the Concrete Structures Division of the Civil and Environmental Engineering Faculty at Gdansk University of Technology, the reinforced concrete beams were subjected to destruction...
-
Tribo-Environment Dependent Chemical Modification of Sliding Interfaces in Ultrananocrystalline Diamond Nanowall Film: A Correlation with Friction and Wear
PublikacjaTribological properties of ultrananocrystalline diamond nanowall (UNCD NW) films were investigated quantitatively in three different and controlled tribo-environmental conditions, proposing the passivation and graphitization mechanisms. However, these mechanisms are rather complicated and possibly can be understood in well-controlled tribological conditions. It was shown that the friction and wear of these films were high in highPage 1...
-
Nutrient transport and acquisition by diatom chains in a moving fluid
PublikacjaThe role of fluid motion in delivery of nutrients to phytoplankton cells is a fundamental question in biological and chemical oceanography. In the study of mass transfer to phytoplankton, diatoms are of particular interest. They are non-motile, are often the most abundant components in aggregates and often form chains, so they are the ones expected to benefit most from enhancement of nutrient flux due to dissipating turbulence....
-
Microcracking monitoring and damage detection of graphene nanoplatelets-cement composites based on acoustic emission technology
PublikacjaThis study aims to identify the micro-cracking pattern and structural applications of cement composites replaced with 0 wt%, 0.04 wt%, and 0.08 wt% contents of graphene nanoplatelets (GNPs) over cement weight through acoustic emission (AE) monitoring under mechanical degradation. The ultraviolet-visible spectroscopy (UV–vis) results showed that at 60 min sonication period, GNP-4 showed maximum absorbance rate of 16.15% compared...
-
On a flexomagnetic behavior of composite structures
PublikacjaThe popularity of the studies is getting further on the flexomagnetic (FM) response of nano-electro-magneto machines. In spite of this, there are a few incompatibilities with the available FM model. This study indicates that the accessible FM model is inappropriate when considering the converse magnetization effect that demonstrates the necessity and importance of deriving a new FM relation. Additionally, the literature has neglected...
-
Medical Image Dataset Annotation Service (MIDAS)
PublikacjaMIDAS (Medical Image Dataset Annotation Service) is a custom-tailored tool for creating and managing datasets either for deep learning, as well as machine learning or any form of statistical research. The aim of the project is to provide one-fit-all platform for creating medical image datasets that could easily blend in hospital's workflow. In our work, we focus on the importance of medical data anonimization, discussing the...
-
Analysis of the impact of AOP on source code quality: Paradox of aspect-oriented separation of concerns
PublikacjaAlmost four decades ago, Parnas advocated modularity for the sake of changeability, independent development, and comprehensibility. The recipe for modularization is to define a clean interface, hide an implementation detail, keep low coupling and high cohesion. Although modules have taken many forms over the years from functions and procedures to classes, no form has been capable of expressing so-called crosscutting concerns in...
-
Heterogeneity of quaternary structure of glucosamine-6-phosphate deaminase from Giardia lamblia
PublikacjaThe oligoHis-tagged versions of glucosamine-6- phosphate deaminase from Giardia lamblia (GlmNagB-HisN, GlmNagB-HisC) were constructed and purified to hear homogeneity, and their kinetic and structural properties were compared to those of the wild-type enzyme (GlmNagB). Introduction of the oligoHis tag at the GlmNagB C-terminus resulted in almost complete loss of the catalytic activity, while the catalytic properties of GlmNagB-HisN...
-
Selection of Organic Coating Systems for Corrosion Protection of Industrial Equipment
PublikacjaThe most important element of corrosion protection in industrial conditions is the protective coating system. However, selecting the right coating can often be a real problem due to the sheer number of coating manufacturers and their products on the market. A quantitative approach based on the data mining technique used to analyze the obtained multi-site exposure data has been proposed. This was demonstrated by the example of the...
-
THE METHOD OF ANALYSIS OF DAMAGE REINFORCED CONCRETE BEAMS USING TERRESTRIAL LASER SCANNING
PublikacjaThe authors present an analysis of the possibility to assess deformations and mode of failure of R-C beams using terrestrial laser scanning. As part of experiments carried out at the Regional Laboratory of Construction (at Gdansk University of Technology), reinforced concrete beams were subjected to destruction by bending and by shear. The process of press impact on the reinforced concrete beam was recorded using terrestrial laser...
-
Positive management of the university
PublikacjaPurpose: To demonstrate that contemporary universities may be improved by synthesis of strategic antinomies, i.e. seeking the possibility of combining opposite approaches to solving problems concerning university organization and management. Findings: That approach discounts the importance of building positive relationships between members of staff and undertaking activities intended to create a situation where the...
-
Methylene Blue Near-Infrared Fluorescence Imaging in Breast Cancer Sentinel Node Biopsy
PublikacjaIntroduction: Fluorescence-based navigation for breast cancer sentinel node biopsy is a novel method that uses indocyanine green as a fluorophore. However, methylene blue (MB) also has some fluorescent properties. This study is the first in a clinical series presenting the possible use of MB as a fluorescent dye for the identification of sentinel nodes in breast sentinel node biopsy. Material and methods: Forty-nine patients with...
-
A multithreaded CUDA and OpenMP based power‐aware programming framework for multi‐node GPU systems
PublikacjaIn the paper, we have proposed a framework that allows programming a parallel application for a multi-node system, with one or more GPUs per node, using an OpenMP+extended CUDA API. OpenMP is used for launching threads responsible for management of particular GPUs and extended CUDA calls allow to manage CUDA objects, data and launch kernels. The framework hides inter-node MPI communication from the programmer who can benefit from...
-
State-of-the-art framework for high-speed camera and photogrammetric use in geometry evaluation of prestressed concrete failure process
PublikacjaPrestressed structures are a key to the realization of the boldest architectural ideas, regardless of shape complexity, great height and large span. A characteristic feature of the prestressed structure is the better use of concrete material properties by insertion of internal forces. The internal forces are opposed to external loads effects (forces and deformations of structure). Prestressed reinforced concrete beams are characterized...
-
Modelling of laminated glass PVB walls of buildings exposed to vehicle impact with different speeds
PublikacjaThis paper presents an analytical model, developed for laminated glass subjected to a low-velocity impact. It has the ability to capture glass cracks as well as large non-linear deformations. It is based mathematically on the firstorder deformation concept, which considers the effect of membrane and transverse shear as well as bending. This theory uses damage mechanics to capture the glass cracking. For this purpose, several experiments...
-
Earthquake-Induced Pounding of Medium-to-High-Rise Base-Isolated Buildings
PublikacjaDuring earthquakes, out-of-phase vibrations in adjacent buildings with limited distance may cause pounding between them. In recent years, the use of seismic isolation has expanded considerably as an effective approach to reduce seismic damage. However, the isolated building experiences large displacements during earthquakes, and there is a possibility of collisions with adjacent structures. The research on earthquake-induced pounding...
-
Combined environmental testing device for picosatellites
PublikacjaAs access to space conditions becomes more available, both technically and economically, scientists’ interest in launching finer and more sophisticated experiments grows. To be qualified for launch, such experiments need to be carefully tested prior to the event. The tests should represent actual launch conditions as closely and in a detailed manner. Typical tests for payload include: vibration tests, thermal and vacuum tests,...
-
Latest Achievements in Concrete Structures Three-Dimensional Printing
PublikacjaWe can hear about three-dimensional printed concrete structures for several years, up to date solutions in this technology allow entire printing settlements of tiny concrete houses. Due to technical limitations, these houses are still small and not very durable, but undoubtedly, this technology is developing. Home printed in three-dimensional technology can be an alternative to modular container buildings implemented in areas affected...
-
Detecting type of hearing loss with different AI classification methods: a performance review
PublikacjaHearing is one of the most crucial senses for all humans. It allows people to hear and connect with the environment, the people they can meet and the knowledge they need to live their lives to the fullest. Hearing loss can have a detrimental impact on a person's quality of life in a variety of ways, ranging from fewer educational and job opportunities due to impaired communication to social withdrawal in severe situations. Early...
-
Modeling the Customer’s Contextual Expectations Based on Latent Semantic Analysis Algorithms
PublikacjaNowadays, in the age of Internet, access to open data detects the huge possibilities for information retrieval. More and more often we hear about the concept of open data which is unrestricted access, in addition to reuse and analysis by external institutions, organizations and people. It’s such information that can be freely processed, add another data (so-called remix) and then published. More and more data are available in text...
-
Ibrutinib as Treatment for Patients With Relapsed/Refractory Follicular Lymphoma: Results From the Open-Label, Multicenter, Phase II DAWN Study
Publikacja -
Increasing the conductivity of V2O5 -TeO2 glass by crystallization: structure and charge transfer studies
PublikacjaIn the present paper, V2O5-TeO2 glass...
-
A demand for innovation support in samll and medium-sized enterprises in the baltic sea region
Publikacjathe aim of the expertise is to analyze the actual demand of smes from the baltic sea region for innovation support. the results of the conducted study can help formulate recommendations designed to increase innovation and competitiveness of smes in the baltic sea region in the future. research activities of this study include: the evaluation of innovation level of the baltic sea region enterprises (type and intensity of implemented...
-
ZMYND10 Is Mutated in Primary Ciliary Dyskinesia and Interacts with LRRC6
Publikacja -
Doskonalenie strumienia wartości
PublikacjaKsiążka ta ma na celu praktyczne ujęcie problemu optymalizacji przedsiębiorstwa opartej na koncepcji Lean (z ang. Lean – szczupły) i jej narzędziu Mapowania Strumienia Wartości. ---- Tu pobierzesz jej pełną treść w wersji elektronicznej: https://drive.google.com/file/d/1xNrdiuOHKpyjzG5dY3ocFG8fp2hY1b9C/view?usp=sharing ---- Prezentowane...
-
Gendered Self-Views Across 62 Countries: A Test of Competing Models
Publikacja -
Psychometric Properties and Correlates of Precarious Manhood Beliefs in 62 Nations
Publikacja -
CBM Collaboration
Publikacja -
CBM Collaboration
Publikacja -
Challenges in QCD matter physics --The scientific programme of the Compressed Baryonic Matter experiment at FAIR
Publikacja