Filtry
wszystkich: 1190
wybranych: 1004
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: NONLOCAL CONTINUUM
-
NONLINEAR VIBRATION ANALYSIS OF BEAM AND PLATE WITH CLOSED CRACK: A REVIEW
PublikacjaThe effect of nonlinearity is high sensitivity in damage detection, especially for closed cracks and delamination. This review illustrates the results of several researchers dealing with nonlinear effects caused by the closure of cracks in the structure, i.e., beam and plate structures. Early detection of damage is an important aspect for the structure and, therefore, continuous progress is being made in developing new and effective...
-
Intelligent monitoring the vertical dynamics of wheeled inspection vehicles
PublikacjaThe problem of intelligent monitoring of the vertical dynamics of wheeled inspection vehicles is addressed. With the independent MacPherson suspension system installed, the basic analysis focuses on the evaluation of the parameters of the so-called quarter car model. To identify a physically motivated continuous description, in practice, dedicated integral-horizontal filters are used. The obtained discrete model, which retains...
-
Low temperature growth of diamond films on optical fibers using Linear Antenna CVD system
PublikacjaIt is not trivial to achieve a good quality diamond-coated fibre interface due to a large difference in the properties and composition of the diamond films (or use coating even) and the optical fibre material, i.e. fused silica. One of the biggest problems is the high temperature during the deposition which influences the optical fibre or optical fibre sensor structure (e.g. long-period gratings (LPG)). The greatest advantage of...
-
Selective H2 production from plastic waste through pyrolysis and in-line oxidative steam reforming
PublikacjaThis study deals with the proposal of pyrolysis and in-line oxidative steam reforming (P-OSR) for plastic waste valorization and assesses the potential of this strategy for the selective production of H2. Overall, the study aims at progressing towards the fine-tuning of the pyrolysis-reforming technology by co-feeding O2. Thus, a multi-point O2 injection system has been developed to ensure a suitable O2 distribution in the reforming...
-
Electrochemical Production of Sodium Hypochlorite from Salty Wastewater Using a Flow-by Porous Graphite Electrode
PublikacjaThe production of sodium hypochlorite (NaOCl) from salty wastewater using an electrochemical cell has several advantages over other methods that often require hazardous chemicals and generate toxic waste, being more sustainable and environmentally friendly. However, the process of producing sodium hypochlorite using an electrochemical cell requires careful control of the operating conditions, such as the current density, flow rate,...
-
Odtwarzanie przebiegu trasy kolejowej o złożonym ukształtowaniu geometrycznym
PublikacjaKształt eksploatowanych torów kolejowych jest w niektórych sytuacjach bardzo złożony, a jednocześnie − jak wykazały przeprowadzone ciągłe pomiary satelitarne − niekiedy tak zdeformowany, że określenie kierunków głównych okazuje się niemożliwe.W pracy przedstawiono program komputerowy do odtwarzania przebiegu trasy kolejowej w takich właśnie przypadkach. Przygotowano zestaw funkcji realizujących połączenia prostych i łuków kołowych...
-
Bypass kolejowy dla wiaduktu łukowego i kratownicowego w ciągu modernizowanej linii kolejowej E59 na odcinku Wronki – Dobiegniew
PublikacjaW artykule przedstawiono realizacje bypassu kolejowego, zlokalizowanego nieopodal miejscowości Krzyż Wielkopolski w ciągu linii kolejowej E59 na skrzyżowaniu z linią kolejową 203. Wariantowa analiza kilku zaproponowanych rozwiązań wykazała, ze wykonstruowanie bypassu na czas prowadzenia prac modernizacyjnych pozwoli na utrzymanie ciągłości ruchu kolejowego, nie stworzy nadmiernych problemów podróżnym, a jednocześnie pozwoli na...
-
Wyznaczanie wytrzymałości betonu na podstawie funkcji dojrzałości wg amerykańskiej normy ASTM C1074-11
PublikacjaArtykuł poświęcono wyznaczaniu wytrzymałości betonu na podstawie funkcji dojrzałości wg normy ASTM C1074-11 (ang. Maturity Method). Metoda bazuje na rejestracji zmian tem - peratury w trakcie hydratacji dojrzewającego betonu. Wartykule zaprezentowano procedurę badawczą służącą wyznaczeniu funk - cji dojrzałości dla wybranej mieszanki betonowej oraz zależności wytrzymałość-dojrzałość. Celem badań jest wyznaczanie zmian w czasie...
-
Local dynamics of fluids and dielectrics as the foundation of signal-carrying wave properties
PublikacjaThis paper develops an original approach to fundamental problems of classical linear acoustics and electromagnetics, proving a crucial role of doubly-dynamic local properties of a propagation medium in supporting wave-like fields able to carry information signals. The proof is composed of two steps concerning, subsequently, fluid acoustics and dielectric electromagnetics. The first step consists in complementing a common, practically...
-
On coertia and inertia in aspects of Natanson’s nonlinear extended thermodynamics
PublikacjaIn this article, the previously underrepresented contributions of Natanson to the field of thermodynamics have been presented. In order to identify a source of irreversibility at Nature, Natanson introduced the concept of Coertia, which is similar to inertia. Natanson’s Coertia is a fundamental property of space that is responsible for every irreversible phenomena in matter, as well as in the electromagnetic and gravitational fields....
-
Radiative lifetime of a BODIPY dye as calculated by TDDFT and EOM-CCSD methods: solvent and vibronic effects
PublikacjaThe radiative emission lifetime and associated S1 excited state properties of a BODIPY dye are investigated with TDDFT and EOM-CCSD calculations. The effects of a solvent are described with the polarizable continuum model using the linear response (LR) approach as well as state-specific methods. The Franck–Condon (FC), Herzberg–Teller (HT) and Duschinsky vibronic effects are evaluated for the absorption and emission spectra, and...
-
A chemo-mechano-thermodynamical contact theory for adhesion, friction, and (de)bonding reactions
PublikacjaThis work presents a self-contained continuum formulation for coupled chemical, mechanical, and thermal contact interactions. The formulation is very general and, hence, admits arbitrary geometry, deformation, and material behavior. All model equations are derived rigorously from the balance laws of mass, momentum, energy, and entropy in the framework of irreversible thermodynamics, thus exposing all the coupling present in the...
-
Microscopic and Spectroscopic Imaging and Thermal Analysis of Acrylates, Silicones and Active Pharmaceutical Ingredients in Adhesive Transdermal Patches
PublikacjaDermal or transdermal patches are increasingly becoming a noteworthy alternative ascarriers for active pharmaceutical ingredients (APIs), which makes their detailed physicochemical evaluation essential for pharmaceutical development. This paper demonstrates mid-infrared (FTIR) and Raman spectroscopy with complementary microscopic methods (SEM, optical and confocal Raman microscopy) and differential scanning calorimetry...
-
Volumetric incorporation of NV diamond emitters in nanostructured F2 glass magneto-optical fiber probes
PublikacjaIntegration of optically-active diamond particles with glass fibers is a powerful method of scaling diamond's magnetic sensing functionality. We propose a novel approach for the integration of diamond particles containing nitrogen-vacancy centers directly into the fiber core. The core is fabricated by stacking the preform from 790 soft glass canes, drawn from a single rod dip-coated with submicron diamond particles suspended in...
-
Suspension and process parameters selection for electrophoretic deposition of Mn–Co spinel coating on steel interconnects
PublikacjaMetallic interconnect coatings, consisting of MnCo2O4 spinel, were effectively applied to Crofer 22 APU using the electrophoretic deposition (EPD) method in both H2O: ethanol and pure ethanol solvents. The primary goal of this method was to prevent chromium migration, minimize evaporation, and control the oxidation rate. The study aimed to assess the quality, adhesion, and thickness of the Mn–Co coating, with the objective of...
-
Colloidal transport of lipid digesta in human and porcine small intestinal mucus
PublikacjaSmall intestinal mucus transport of food-derived particulates has not been extensively studied, despite mucus being a barrier nutrients need to cross before absorption. We used complex dispersions of digesta obtained from simulated, dynamic gastrointestinal digestion of yogurt to examine the penetrability of human and porcine mucus to the particles formed of lipolysis products. Quantitative, time-lapse confocal microscopy revealed...
-
Properties comparison of rubber and three layer PTFE-NBR-bronze water lubricated bearings with lubricating grooves along full bush circumference based on experimental tests
PublikacjaWater lubricated bearings have been in industrial use for well over a century. During the last decade their traditional range has been expanded with new, modern products. Despite that fact, certain solutions continue to employ the standard rubber bearing with lubricating grooves located along entire bush circumference. The work presents experimental research conducted on comparable sliding bearings with lubrication grooves along...
-
Can we rely on the pulse transit time - pressure relationship - models comparison
PublikacjaAn unobtrusive, noninvasive and continuous pressure measurement is invaluable however, still being under research and development. There are many attempts proposing an appropriate relationship between pulse pressure velocity and pressure. Fifteen different formulas, both theoretical and experimental, describing relation between blood pressure and crosssectional area of the vessel were examined. Using these formulas the relation...
-
Quasi-discrete modelling of PMSM phase currents in drives with low switching-to-fundamental frequency ratio
PublikacjaThis study proposes a new quasi-discrete approach to modelling the permanent magnet synchronous motor (PMSM). The quasi-discrete modelling reflects the impact of continuous rotor movement, which takes place during a control cycle, on the shape of motor current waveforms. This provides much improvement in current modelling accuracy under inverter low switching-to-fundamental frequency operation. The proposed approach may be used...
-
Hard carbon derived from rice husk as low cost negative electrodes in Na-ion batteries
PublikacjaHere, we report the synthesis of hard carbon materials (RH) made from natural rice husk through a single pyrolysis process and their application as an anode in sodium-ion batteries. The studies show that the electrochemical properties of RHs are affected by the treatment temperatures, which determine the materials morphology, in particular, their degree of graphitization and extent of continuous channels (nanovoids). The latter...
-
Online urban acoustic noise monitoring system
PublikacjaConcepts and implementation of the Online Urban Noise Monitoring System are presented. Principles of proposed solution used for dynamic acoustical maps creating are discussed. The architecture of the system and the data acquisition scheme are described. The concept of noise mapping, based on noise source model and propagation simulations, was developed and employed in the system. Dynamic estimation of noise source parameters utilized...
-
A Hyperdense Semantic Domain for Discontinuous Behavior in Physical System Models
PublikacjaMultiple time models have been proposed for the formalization of hybrid dynamic system behavior. The superdense notion of time is a well-known time model for describing event-based systems where several events can occur simultaneously. Hyperreals provide a domain for defining the semantics of hybrid models that is elegantly aligned with first principles in physics. This paper discusses the value of both time models and shows how...
-
Designing Intelligent Factory: Conceptual Framework and Empirical Validation
PublikacjaThis paper presents a framework for monitoring, analysing and decision making for a smart manufacturing environment. We maintain that this approach could play a vital role in developing an architecture and implementation of Industry 4.0. The proposed model has features like experience based knowledge representation and semantic analysis of engineering objects and manufacturing process. It is also capable of continuous real time...
-
The influence of applying supplementary web plates on structural joint moment resistance and rotational stiffness
PublikacjaContinual trend to simplify structural elements and find less time-consuming solutions on construction site as well as inevitable increase in labour costs determine for instance elimination of those technological steps that are difficult to automation. Welding additional reinforcements and web stiffeners is a great example of such a step. The method presented in EN 1993-1-8 [8] is a result of long-term studies focused on calculating...
-
The Doppler effect in a bistatic system for determining the position of moving targets
PublikacjaThe article presents the theoretical analysis and the results of numerical calculations of the Doppler effect it occurs in a system designed to determine the position and speed of a moving target. The transmitter is the source of the signal and it emits a sinusoidal, acoustic and continuous wave. Signal reflected off a moving target is received by four hydrophones. Based on the signals, four Doppler shifts are determined and inserted...
-
Quality assessment of ZnO-based varistors by 1/f noise
PublikacjaNoise has been used as a diagnostic tool of surge arrester varistor structures comprising of ZnO grains of various type and size. The physical and electrical properties of the measured samples have been described. In the experimental study, the applied measurement system and the results of noise measurements for the selected structures of varistors designed for the continuous working voltage 280 V, 440 V and 660 V have been presented....
-
Estimation of a Stochastic Burgers' Equation Using an Ensemble Kalman Filter
PublikacjaIn this work, we consider a difficult problem of state estimation of nonlinear stochastic partial differential equations (SPDE) based on uncertain measurements. The presented solution uses the method of lines (MoL), which allows us to discretize a stochastic partial differential equation in a spatial dimension and represent it as a system of coupled continuous-time ordinary stochastic differential equations (SDE). For such a system...
-
Ceria Based Protective Coatings for Steel Interconnects Prepared by Spray Pyrolysis
PublikacjaStainless steels can be used in solid oxide fuel/electrolysis stacks as interconnects. For successful long term operation they require protective coatings, that lower the corrosion rate and block chemical reactions between the interconnect and adjacent layers of the oxygen or the hydrogen electrode. One of the promising coating materials for the hydrogen side is ceria. Using standard sintering techniques, ceria sinters at around...
-
The Impact of Crushed Rock Spoil on Pitting Corrosion of Selected Stainless Steel
PublikacjaThe paper presents the results of the pitting resistance investigations of selected stainless steels in the chloride environment and the simultaneous impact of erosive factors using the cyclic polarization technique. Additionally, using electrochemical techniques, ie: electrochemical impedance spectroscopy (EIS) and measurement of corrosion potential, the behavior of the passive layer of selected stainless steels in the environment...
-
Theoretical pKa prediction of O-phosphoserine in aqueous solution
PublikacjaSprawdzono zdolność modelu polaryzowalnego kontinuum (PCM) do przewidywania wartości pKa w roztworze wodnym dla O-fosfoseryny (P-Ser). Obliczenia przeprowadzono w ramach teorii funkcjonału gęstości (DFT) przy użyciu funkcjonałów B3LYP i M06-2X oraz baz 6-31+G(d) and 6-31+G(d,p). Obliczenia na poziomie B3LYP/6-31+G(d,p) przy użyciu modelu solwatacji SMD zapewniają doskonałą zgodność z doświadczeniem, pod warunkiem uwzględnienia...
-
E-cohomological Conley index
PublikacjaIn this thesis we continue with developing the E-cohomological Conley index which was introduced by A.Abbondandolo. In particular, we generalize the index to non-gradient flows, we show that it an possesses additional multiplicative structure and we prove the continuation principle. Then, using continuation principle, we show how the computation of the E-cohomological Conley index can be reduced to the computation of the classical...
-
Ciliated protozoa in the impact zone of the Uzhgorod treatment plant
PublikacjaThis paper presents the results of studies on the Uzh River (Ukraine, Zakarpattia Oblast) near the effluent point of a sewage treatment plant in Uzhgorod. The samples were taken at various sites of the treatment plant along the stages of purification process, as well as in the river, at a number of different points above and below the wastewater discharge. At each of these objects, the temperature...
-
Design of a Shape-Memory-Alloy-Based Carangiform Robotic Fishtail with Improved Forward Thrust
PublikacjaShape memory alloys (SMAs) have become the most common choice for the development of mini- and micro-type soft bio-inspired robots due to their high power-to-weight ratio, ability to be installed and operated in limited space, silent and vibration-free operation, biocompatibility, and corrosion resistance properties. Moreover, SMA spring-type actuators are used for developing different continuum robots, exhibiting high degrees...
-
Preface
PublikacjaThis special issue of Discussiones Mathematice Graph Theory (DMGT) is dedicated to selected papers presented at the 13th Workshop on Graph Theory: Colourings, Independence and Domination (CID) held on 18-23 September 2009 in Szklarska Poręba, Poland. It continues a series of international workshops: 1993-1997 in Lubiatów, 1998-2001 in Gronów, and 2003-2007 in Karpacz. The meeting was organized by the Faculty of Mathematics, Computer...
-
Chapter 2: Modelling and analysis of rotor with magnetic bearing system
PublikacjaThe paper is concerned with rotor magnetic bearing system modelling. Such system is a relatively complex electromechanical system and can be considered as typical mechatronic one. The port-based modelling of physical systems has been used to obtain discrete-continuous model of considered system. Proposed approach enables to obtain reduced low-order lumped parameter representation of the system including gyroscopic interactions....
-
Derivation of Executable Test Models From Embedded System Models using Model Driven Architecture Artefacts - Automotive Domain
PublikacjaThe approach towards system engineering compliant to Model-Driven Architecture (MDA) implies an increased need for research on the automation of the model-based test generation. This applies especially to embedded real-time system development where safety critical requirements must be met by a system. The following paper presents a methodology to derive basic Simulink test models from Simulink system models so as to execute them...
-
Remote sensing in laboratory diagnostics of reinforced concrete elements – current development and vision for the future
PublikacjaContinuous emergence of new concrete types and kinds of reinforcement, as well as technological solutions in the field of structural engineering have made great demand for diagnostic tests of reinforced concrete elements. New challenges and problems facing people require new more efficient tools for laboratory diagnostics than those commonly used. Remote sensing may be the answer to this demand. In this paper the author describes...
-
Tradycyjna versus przyspieszona internacjonalizacja przedsiębiorstw z branż high-tech. Wyniki badań empirycznych
PublikacjaThe discussion on the role and importance of time in the process of internationalization of firms belongs to the mainstream of research in the field of internationalization. In the literature, the phenomenon of early and rapid internationalization was noticed in the early 1980s; however, the intensive development of the research into this phenomenon began a decade later and continues today. For several years in Poland, the share...
-
Modeling, simulation, and validation of a TB41 crash test of the H2/W5/B concrete vehicle restraint system
PublikacjaThe paper addresses numerical simulations of a concrete vehicle restraint system. The model is described in detail. The advanced material law of the continuous surface cap model was used to analyze the damage locations in concrete barrier segments. The results were validated against the TB41 full-scale crash test. The test was conducted in compliance with European standard EN 1317, and the validation was performed in accordance...
-
Remote sensing in laboratory diagnostics of reinforced concrete elements – current development and vision for the future
PublikacjaContinuous emergence of new concrete types and kinds of reinforcement, as well as technological solutions in the field of structural engineering have made great demand for diagnostic tests of reinforced concrete elements. New challenges and problems facing people require new more efficient tools for laboratory diagnostics than those commonly used. Remote sensing may be the answer to this demand. In this paper the author describes...
-
Weak forms of shadowing in topological dynamics
PublikacjaWe consider continuous maps of compact metric spaces. It is proved that every pseudotrajectory with sufficiently small errors contains a subsequence of positive density that is point-wise close to a subsequence of an exact trajectory with the same indices. Also, we study homeomor- phisms such that any pseudotrajectory can be shadowed by a finite number of exact orbits. In terms of numerical methods this property (we call it multishadowing)...
-
Event-Triggered Communication in Cooperative, Adaptive Model Predictive Control of a Nuclear Power Plant’s Turbo–Generator Set
PublikacjaThis paper discusses the issue of optimizing the communication between the components of a cooperating control system formed by a pair of MPC controllers of a nuclear power plant turbine set using online recursive least squares identification. It is proposed to use event-triggered communication, i.e., sending information only at selected time instants, as opposed to the standard approach where communication is triggered by time...
-
Playing the Sprint Retrospective: A Replication Study
PublikacjaThe Sprint Retrospective is a vehicle for continuous process improvement. Even though it is a well established agile practice, running effective retrospective meetings is challenging. There have been a lot of identified problems that commonly occur during these meetings. To address them, Przybyłek & Kotecka [20] successfully revitalized retrospective meetings by adopting collaborative games, which represent a powerful tool in improving...
-
Lignin-based carbon fibers for renewable and multifunctional lithium-ion battery electrodes
PublikacjaLignin-based carbon fibers (LCFs) from the renewable resource softwood kraft lignin were synthesized via oxidative thermostabilization of pure melt-spun lignin and carbonization at different temperatures from 1000°C to 1700°C. The resulting LCFs were characterized by tensile testing, scanning electron microscopy (SEM), X-ray diffraction (XRD) and confocal Raman spectroscopy. The microstructure is mainly amorphous carbon with some...
-
Towards azeotropic MeOH-MTBE separation using pervaporation chitosan-based deep eutectic solvent membranes
PublikacjaDeep eutectic solvents (DESs) are a new class of solvents that can offset some of the major drawbacks of common solvents and ionic liquids. When dealing with the preparation of dense membranes, the use of DESs is still challenging due to their low compatibility with the polymer phase. In this research, a novel L-proline:sulfolane (molar ratio 1:2) DES was synthesized and used for the preparation of more sustainable bio-based membranes...
-
Correlations of structural, thermal and electrical properties of sodium doped complex borophosphosilicate glass
PublikacjaBorophosphosilicate glasses with varying sodium ion concentrations were investigated for their, structural, thermal, and electrical properties. All the obtained glasses were transparent except the glass with the highest sodium content, which exhibited translucency due to inhomogeneities. Increasing sodium content led to reduced boron and silicon content while maintaining a constant B/Si ratio, indicating progressive depolymerization...
-
pH-Responsive Drug Delivery Nanoplatforms as Smart Carriers of Unsymmetrical Bisacridines for Targeted Cancer Therapy
PublikacjaSelective therapy and controlled drug release at an intracellular level remain key challenges for effective cancer treatment. Here, we employed folic acid (FA) as a self-navigating molecule in nanoconjugates containing quantum dots (QDs) and β-cyclodextrin (β-CD) for the delivery of antitumor unsymmetrical bisacridine compound (C-2028) to lung and prostate cancers as well as normal cells. The bisacridine derivative can form the...
-
Experimental research on water lubricated marine stern tube bearings in conditions of improper lubrication and cooling causing rapid bush wear
PublikacjaWater lubricated bearings are popular in sliding bearings of marine propeller shafts, turbines and pump shafts. Such popularity is partly due to their simple construction which also means a relatively affordable price. In practical experience one may also observe cases of rapid wear or even malfunctions of this bearings, some of which may be caused by insufficient flow of lubricant leading to overheating. The conducted...
-
Elderly persons professional activity - substantive issues and methodological challenges
PublikacjaPopulation ageing in Europe and mass withdrawal from professional activity leads to a number of adverse phenomena, such as increased public spending, reduced consumer demand and the growing problem of social exclusion. The study focuses on the problems of population ageing in Europe as well as on the feasible steps that may be taken with a view to professional activation of the elderly. The first part is concerned with the trends...
-
Approximate Cramér–Rao bound on Doppler error in correlation-processing relatively narrowband noise radar
PublikacjaThe paper studies limitations on accuracy of Doppler estimation in continuous-wave noise radar with correlation processing. Second order properties of output of the correlation receiver are evaluated and an approximate Cram´er-Rao bound on errors of Doppler measurement is derived. The accuracy of Doppler measurements is found to be affected by the following factors: power spectral density of noise signal, frequency response of the...