Filtry
wszystkich: 914
wybranych: 745
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: MAXWELL FLUID
-
Comparison of various flow maldistribution quantification methods in mini heat exchangers
PublikacjaThe aim of study is to compare various flow maldistribution quantification methods, using velocity, mass flow rate, pressure, and temperature. An experimentally validated numerical study has been prepared and a heat exchanger with 34 semi-circular channels with a diameter of 3.1 mm has been tested. The minichannels were heated from the bottom with a heat flux of 50, 60, 70, and 80 kW/m2. The cases for various inlet velocities of...
-
Modeling of free vibrations and resonant frequencies of simply-supported submerged horizontal plate
PublikacjaA theoretical approach was applied to study the vibration of simple-supported submerged horizontal plate. The derived analytical solution was used to determine natural frequencies for a horizontal plate vibrating in fluid. The investigations were conducted for a very wide range of material density and elasticity modulus covering all materials used in engineering practice. Analysis shows that plate vibration frequency decreases...
-
Properties of New Composite Materials Based on Hydroxyapatite Ceramic and Cross-Linked Gelatin for Biomedical Applications
PublikacjaThe main aim of the research was to develop a new biocompatible and injectable composite with the potential for application as a bone-to-implant bonding material or as a bone substitute. A composite based on hydroxyapatite, gelatin, and two various types of commercially available transglutaminase (TgBDF/TgSNF), as a cross-linking agent, was proposed. To evaluate the impacts of composite content and processing parameters on various...
-
Effect of the Cavitation Generation Unit Structure on the Performance of an Advanced Hydrodynamic Cavitation Reactor for Process Intensifications
PublikacjaThe advanced rotational hydrodynamic cavitation reactors (ARHCRs) that appeared recently have shown obvious advantages compared with conventional devices in process intensifications. In ARHCRs, the cavitation generation unit (CGU) located on the rotor and stator basically determines their performance. For the first time, the present study investigated the effect of the CGU structure on the performance of a representative ARHCR...
-
Numerical investigation on distribution characteristics of oxidation air in a lime slurry desulfurization system with rotary jet agitators
PublikacjaRotary jet agitator is an effective device for mixing, dispersing, dissolving, and suspending dispersed phases in liquid, and is particularly advantageous to the homogenization of oxygen-enriched air within the lime slurry desulfurization system. The distribution of oxygen-enriched air in agitators is vital for the process of gypsum crystallization and the homogeneous and sufficient oxygen-enriched air can promote the formation...
-
Investigating the effects of structural pounding on the seismic performance of adjacent RC and steel MRFs
PublikacjaAn insufficient separation distance between adjacent buildings is the main reason for structural pounding during severe earthquakes. The lateral load resistance system, fundamental natural period, mass, and stiffness are important factors having the influence on collisions between two adjacent structures. In this study, 3-, 5- and 9-story adjacent reinforced concrete and steel Moment Resisting Frames (MRFs) were considered to investigate...
-
Effects of Noncontact Shoulder Tool Velocities on Friction Stir Joining of Polyamide 6 (PA6)
PublikacjaIn this study, the effects of the traverse and rotational velocities of the noncontact shoulder tool on the heat generation and heated flux during the friction stir joining of high-density polyamide 6 (PA6) polymer were investigated. The computational fluid dynamics (CFD) method was employed to simulate the thermomechanical phenomena during the friction stir joining (FSJ) process of PA6. A developed model was used to consider the...
-
Weldability of pipe grade polyethylenes as realized from thermal and mechanical properties assessments
PublikacjaSince polyethylene (PE) has been widely accepted for the production of high-pressure fluid conveying pipelines, studies devoted to weldability of PE connections were always of major importance. In this study, two industrial PE grades designed for pipe production, namely PE80 and PE100, were injection molded, cut, and then welded as PE100-PE100, PE100-PE80, and PE80-PE80. The heat-welded joints were assessed by differential scanning...
-
DETERMINATION OF THE AERODYNAMIC DRAG OF PNEUMATIC LIFE RAFTS AS A FACTOR FOR INCREASING THE RELIABILITY OF RESCUE OPERATIONS
PublikacjaEnsuring the safety of ship crews at sea is of the utmost importance. Life rafts are one of the basic components of any seagoing vessel and ensuring their stability is an important component of maritime research. This study concerns the determination of the aerodynamic drag coefficients of pneumatic life rafts in a full range of wind speed and directions. The drag coefficients are based on full-scale experimental studies and numerical...
-
Ordered titanium templates functionalized by gold films for biosensing applications – Towards non-enzymatic glucose detection
PublikacjaRecently, metal nanostructures evoke much interest due to application potential in highly sensitive detectors in biochemistry and medical diagnostics. In this work we report on preparation and characteristics of thin (1–100 nm) Au films deposited onto highly ordered structured titanium templates for SERS (Surface Enhanced Raman Spectroscopy) and electrochemical sensing. The Ti templates are formed by selective removal of TiO2 nanotubes...
-
Performance analyses of helical coil heat exchangers. The effect of external coil surface modification on heat exchanger effectiveness
PublikacjaThe shell and coil heat exchangers are commonly used in heating, ventilation, nuclear industry, process plant, heat recovery and air conditioning systems. This type of recuperators benefits from simple construction, the low value of pressure drops and high heat transfer. In helical coil,centrifugal force is acting on the moving fluid due to the curvature of thetube results in the development. It has been long recognized that the...
-
Numerical Analysis of Turbulent Flow over a Backward-facing Step in an Open Channel
PublikacjaComputational examinations of the flow field in an open channel having a single Backward--Facing Step (BFS) with a constant water depth of 1.5 m were performed. The effects of the expansion ratio, and the flow velocity along the reattachment length, were investigated by employing two different expansion ratios of 1.5 and 2, and eight various flow velocities of 0.5, 1, 2, 3, 4, 5, 7.5 and 10 m/sec in the Computational Fluid Dynamic...
-
Alternative cogeneration thermodynamic cycles for domestic ORC
PublikacjaThe Organic Flash Cycle (OFC) is suggested as a vapor power cycle that could potentially improve the efficiency of utilization of the heat source. Low and medium temperature finite thermal sources are considered in the cycle. Additionally the OFC’s aim is to reduce temperature difference during heat addition. The study examines 2 different fluids. Comparisons are drawn between the OFC and an optimized basic Organic Rankine Cycle...
-
In vitro biodegradation of bacterial nanocellulose under conditions simulating human plasma in the presence of selected pathogenic microorganisms
PublikacjaThe Biodegradability of bacterial nanocellulose (BNC) was assessed based on a change in its properties under conditions simulating human plasma in the presence or absence of the pathogens Staphylococcus aureus, Candida albicans and Aspergillus fumigatus. It was shown that the dry mass of BNC did not change during 6 months of incubation, except for samples stored in the presence of moulds, where the dry mass reduced by 40 %. The...
-
BIOMATERIALS AND IMPLANTS IN CARDIAC AND VASCULAR SURGERY - REVIEW
PublikacjaCurrently, on prosthesis in cardiac blood vessels and heart valves are used materials of animal or synthetic origin. For animal materials include, among others pericardial sac in which is the heart. Materials such as this (natural) are characterized by a remarkable biocompatibility within the human body, but their main disadvantage is the relatively low durability. In turn, synthetic materials, which include the austenitic chromium-nickel-molybdenum...
-
Application of microturbines in CHP systems with reciprocating engines
PublikacjaThe analysis was carried out for Combined Heat and Power generation systems with micro-turbines power plants working on heat rejected from the reciprocating engine. The calculations were performed for GE Jerbacher engines of J320 GS- C05, J320 GS- C25 and J416 GS- B05 types. We considered different working media (both wet and dry fluids): water, ammonia, ethanol, methanol, methylacetylene (propyne), dimethyloether, sulphur dioxide,...
-
Trends in the new generation of green solvents in extraction processes
PublikacjaAnalytical chemistry, like other scientific fields, has undergone a number of changes to make it more consistent with the concept of sustainable development. Among the various steps of chemical analysis, without a doubt, sample preparation is the bottleneck in regard to following a green protocol, especially in terms of solvent consumption. Therefore, many attempts have been made to improve the environmental friendliness of this...
-
Effect of Chitosan Deacetylation on Its Affinity to Type III Collagen: A Molecular Dynamics Study
PublikacjaThe ability to form strong intermolecular interactions by linear glucosamine polysaccharides with collagen is strictly related to their nonlinear dynamic behavior and hence bio-lubricating features. Type III collagen plays a crucial role in tissue regeneration, and its presence in the articular cartilage affects its bio-technical features. In this study, the molecular dynamics methodology was applied to evaluate the effect of...
-
Identification of Emotional States Using Phantom Miro M310 Camera
PublikacjaThe purpose of this paper is to present the possibilities associated with the use of remote sensing methods in identifying human emotional states, and to present the results of the research conducted by the authors in this field. The studies presented involved the use of advanced image analysis to identify areas on the human face that change their activity along with emotional expression. Most of the research carried out in laboratories...
-
Diagnostic Accuracy of Liquid Biopsy in Endometrial Cancer
PublikacjaBackground: Liquid biopsy is a minimally invasive collection of a patient body fluid sample. In oncology, they offer several advantages compared to traditional tissue biopsies. However, the potential of this method in endometrial cancer (EC) remains poorly explored. We studied the utility of tumor educated platelets (TEPs) and circulating tumor DNA (ctDNA) for preoperative EC diagnosis, including histology determination. Methods:...
-
Extended micropolar approach within the framework of 3M theories and variations thereof
PublikacjaAs part of his groundbreaking work on generalized continuum mechanics, Eringen proposed what he called 3M theories, namely the concept of micromorphic, microstretch, and micropolar materials modeling. The micromorphic approach provides the most general framework for a continuum with translational and (internal) rotational degrees of freedom (DOF), whilst the rotational DOFs of micromorphic and micropolar continua are subjected...
-
Coupling between Blood Pressure and Subarachnoid Space Width Oscillations during Slow Breathing
PublikacjaThe precise mechanisms connecting the cardiovascular system and the cerebrospinal fluid (CSF) are not well understood in detail. This paper investigates the couplings between the cardiac and respiratory components, as extracted from blood pressure (BP) signals and oscillations of the subarachnoid space width (SAS), collected during slow ventilation and ventilation against inspiration resistance. The experiment was performed on...
-
Effect of annealing temperature on slurry erosion resistance of ferritic X10CrAlSi18 steel
PublikacjaIn the present work, the slurry erosion tests were carried out to investigate the influence of heat treatment on slurry erosion process of ferritic X10CrAlSi18 stainless steel using a slurry pot test rig. X10CrAlSi18 stainless steel was tested in as-received condition and after annealing at three different temperatures: 600°C, 800°C and 1000°C. Degradation of materials due to slurry erosion depends on many factors connected with...
-
Aerodynamic Shape Optimization for Delaying Dynamic Stall of Airfoils by Regression Kriging
PublikacjaThe phenomenon of dynamic stall produce adverse aerodynamic loading which can adversely affect the structural strength and life of aerodynamic systems. Aerodynamic shape optimization (ASO) provides an effective approach for delaying and mitigating dynamic stall characteristics without the addition of auxiliary system. ASO, however, requires multiple evaluations time-consuming computational fluid dynamics models. Metamodel-based...
-
Multi-fidelity aerodynamic design trade-off exploration using point-by-point Pareto set identification
PublikacjaAerodynamic design is inherently a multi-objective optimization (MOO) problem. Determining the best possible trade-offs between conflicting aerodynamic objectives can be computationally challenging when carried out directly at the level of high-fidelity computational fluid dynamics simulations. This paper presents a computationally cheap methodology for exploration of aerodynamic design trade-offs. In particular, point-by-point...
-
Variable-fidelity CFD models and co-Kriging for expedited multi-objective aerodynamic design optimization
PublikacjaPurpose – Strategies for accelerated multi-objective optimization of aerodynamic surfaces are investigated, including the possibility of exploiting surrogate modeling techniques for computational fluid dynamic (CFD)-driven design speedup of such surfaces. The purpose of this paper is to reduce the overall optimization time. Design/methodology/approach – An algorithmic framework is described that is composed of: a search space reduction,...
-
Reservoir Influence on Pressure Wave Propagation in Steel Pipes
PublikacjaThe relation between the length of steel pipe and the pressure wave period in the system, reservoir-pipe-valve, is discussed. Experiments carried out for the short steel pipes showed that in such a system, the pressure wave celerity estimated using the measured wave cycles systematically increases with the increase of the pipe length. The observed differences can exceed even 90 m=s. As the pressure wave traveling in the pipe with...
-
Spurious Modes in Model Order Reduction in Variational Problems in Electromagnetics
PublikacjaIn this work, we address an everlasting issue in 2 model order reduction (MOR) in electromagnetics that has 3 remained unnoticed until now. Contrary to what has been 4 previously done, we identify for the very first time spurious 5 modes in MOR for time-harmonic Maxwell’s equations and 6 propose a methodology to remove their negative influence on the 7 reduced order model (ROM) response. These spurious modes 8 have nonzero resonance...
-
MODELOWANIE TURBINY WIATROWEJ Z DWOMA PRZECIWBIEŻNIE OBRACAJĄCYMI SIĘ WIRNIKAMI
PublikacjaW artykule przedstawiono sposoby modelowania dwuwirnikowej turbiny wiatrowej z wykorzystaniem technik Obliczeniowej Mechaniki Płynów. Omówiono uproszczone metody modelowania Actuator Disc i Actuator Line Method oraz aspekty związane z dokładnym odwzorowaniem turbiny na siatce obliczeniowej. Zaprezentowano przykładowe wyniki obliczeń turbiny dwuwirnikowej złożonej z wirników NREL o mocy nominalnej 5 MW każdy. Do wykonania badań...
-
Nowe możliwości generowania zarysów satelitowych mechanizmów roboczych
PublikacjaPlanetary hydraulic gear motors have been well known since 70's . first motors were constructed for maritime industry by hydroster from gdansk. the evolution of this type of motors led to an increase of nominal pressure and durability. nowadays the industry needs reliable and efficient motor able to work with alternative hydraulic fluids like water, emulsion and vegetable oil. therefore a new type of motors are being developed...
-
Determination of isoprostanes in exhaled breath condensate samples by liquid chromatography coupled with tandem mass spectrometry
PublikacjaOxidative stress (OS) is a state of imbalance between continuously generating reactive oxygen species (ROS) during normal cell metabolism and mechanism of detoxifying oxygen radicals through a network of antioxidative enzymes. Isoprostanes are prostaglandin -like substances that are produced in vivo primarily by free radical-induced peroxidation of arachidonic acid. The measurement of isoprostanes in biological fluids and/or tissue...
-
Computer Supported Analysis of the Human Body Surface Area
PublikacjaRecent scientific studies show the growing importance of the coefficients: BSA and TBSA, as an alternative to the widely used BMI. The relevant indicators are widely used in medicine, including such areas as: the treatment of burns, chemotherapy, dermatology and toxicology; as benchmarks when calculating doses of drugs and fluids. The particular problems concerning this subject are: the change of the reference parameter value which...
-
Metodyka badań rozwojowych nowego typu silników i pomp satelitowych
PublikacjaResearch and development of new type satellite motors and satellite pumps SM with small geometrical displacement, from 5 to 73 cm3/rev, has been conducted in cooperation with Stosowanie Maszyn company from Katowice (manufacturer of motors and pump SM). The improvement of construction of those machines, especially construction of axial compensation and construction of fluid distribution channels have been the main problem of research...
-
Numerical Study of the Impinging Jets Formed by an Injector with Different Nozzle Diameters
PublikacjaThe collision of two or more liquid jets may provide considerable atomisation and efficient mixing of injected substances at the same time. This phenomenon is used, among others, in rocket engines, where the fuel and oxidiser are introduced separately and almost immediately mixed through self-impingement. Depending on the injection and operating conditions, diverse configurations of impinging jets are used, such as doublets,...
-
Multi-fidelity robust aerodynamic design optimization under mixed uncertainty
PublikacjaThe objective of this paper is to present a robust optimization algorithm for computationally efficient airfoil design under mixed (inherent and epistemic) uncertainty using a multi-fidelity approach. This algorithm exploits stochastic expansions derived from the Non-Intrusive Polynomial Chaos (NIPC) technique to create surrogate models utilized in the optimization process. A combined NIPC expansion approach is used, where both...
-
Comparative analysis of mechanical conditions in bone union following first metatarsophalangeal joint arthrodesis with varied locking plate positions: A finite element analysis
PublikacjaFirst metatarsophalangeal joint arthrodesis is a typical medical treatment performed in cases of arthritis or joint deformity. The gold standard for this procedure is arthrodesis stabilisation with the dorsally positioned plate. However, according to the authors’ previous studies, medially positioned plate provides greater bending stiffness. It is worth to compare the mechanical conditions for bone formation in the fracture callus...
-
A shear stress micromodel of urinary tract infection by the Escherichia coli producing Dr adhesin
PublikacjaIn this study, we established a dynamic micromodel of urinary tract infection to analyze the impact of UT-segment-specific urinary outflow on the persistence of E. coli colonization. We found that the adherence of Dr+ E. coli to bladder T24 transitional cells and type IV collagen is maximal at lowest shear stress and is reduced by any increase in flow velocity. The analyzed adherence was effective in the whole spectrum of physiological...
-
Fast Multi-Objective Aerodynamic Optimization Using Sequential Domain Patching and Multifidelity Models
PublikacjaExploration of design tradeoffs for aerodynamic surfaces requires solving of multi-objective optimization (MOO) problems. The major bottleneck here is the time-consuming evaluations of the computational fluid dynamics (CFD) model used to capture the nonlinear physics involved in designing aerodynamic surfaces. This, in conjunction with a large number of simulations necessary to yield a set of designs representing the best possible...
-
Cu-HKUST-1 and Hydroxyapatite–The Interface of Two Worlds toward the Design of Functional Materials Dedicated to Bone Tissue Regeneration
PublikacjaA novel composite based on biocompatible hydroxyapatite (HA) nanoparticles and Cu-HKUST-1 (Cu-HKUST-1@HA) has been prepared following a layer-by-layer strategy. Cu-HKUST-1 was carefully selected from a group of four Cu-based metal−organic frameworks as the material with the most promising antimicrobial activity. The formation of a colloidal Cu- HKUST-1 layer on HA nanoparticles was confirmed by various techniques, e.g., infrared...
-
A Concept for Safe and Less Expensive Acceleration of a Marine Steam Turbine Start-up
PublikacjaThis paper analyses the issue of accelerated start-up of a marine steam turbine, which is an important problem because the start-up of a steam machine involves the combustion of fuel that is not transformed into useful energy. To find novel technologies that offer improvements in this aspect is essential due to restrictions on reducing ship emissions. Thus, the shorter the start-up time, the better for the environment and economy....
-
Experimental study on the feasibility of alternative materials for tilting pad thrust bearings operating in transition to mixed friction
PublikacjaIn hydrodynamic bearings traditional bearing alloys: Babbitts and bronzes are most frequently utilized. Polymer sliding layers are sometimes applied as a valuable alternative. Hard diamond-like carbon (DLC) coatings, which are also considered for certain applications may show some advantages, as well. Although material selection is of secondary importance in a full film lubrication regime it becomes important in mixed friction...
-
Thermal Energy Storage with PCMs in Shell-and-Tube Units: A Review
PublikacjaThe paper presents a survey of the experimental and numerical studies of shell-and-tube systems in which phase change material (PCM) is used. Due to the multitude of design solutions for shell-and-tube systems, the emphasis is placed on double-tube (DT), triplex-tube (TT), and multitube (MT) units. Additionally, only single-pass systems are considered. Particular attention is paid to the method of heat transfer intensification....
-
Effect of oxidation and in vitro intestinal hydrolysis on phospholipid toxicity towards HT29 cell line serving as a model of human intestinal epithelium
PublikacjaOxidation of food-derived phospholipids (PLs) can influence nutrient digestion and induce oxidative stress in gastrointestinal epithelium. In this study, hen egg yolk PL fraction was used to evaluate the effect of lipoxygenase (LOX)-induced PL oxidation on the rate of PL hydrolysis catalyzed by pancreatic phospholipase A2 (PLA2) in the presence of bile salts (BSs). Then, PL/BS solutions containing native or oxidized PLs were used...
-
Investigation on polypropylene friction stir joint: effects of tool tilt angle on heat flux, material flow and defect formation
PublikacjaTool tilt angle (TTA) is a critical factor that can control material flow in polymeric materials' friction stir joining (FSJ). This study selected a TTA range between 0° to 4° for FSJ of polypropylene (PP) polymer sheet. A modified computational fluid dynamic (CFD) technique was implemented to gain a deep understanding of the effects of TTA during FSJ of PP. The PP joint's internal flow, defect formation, heat generation, and tensile...
-
Application of the ISE Optimized Proportional Control of the Wave Maker in a Towing Tank
PublikacjaThis paper presents the improvement of the wave maker control system. The wave maker is a facility widely used in hydromechanics laboratories to generate waves in towing tanks. It is equipped with an electrohydraulic drive and an actuator submerged into water. The waves are generated to model the environmental conditions for physical experiments, performed on reduced-scale models of maritime objects. The physical experiments allow...
-
Multi-objective optimization of the cavitation generation unit structure of an advanced rotational hydrodynamic cavitation reactor
PublikacjaHydrodynamic cavitation (HC) has been widely considered a promising technique for industrial-scale process intensifications. The effectiveness of HC is determined by the performance of hydrodynamic cavitation reactors (HCRs). The advanced rotational HCRs (ARHCRs) proposed recently have shown superior performance in various applications, while the research on the structural optimization is still absent. The present study, for the...
-
Numerical Study on Mitigation of Flow Maldistribution in Parallel Microchannel Heat Sink: Channels Variable Width Versus Variable Height Approach
PublikacjaMicrochannel heat sink on one hand enjoys benefits of intensified several folds heat transfer performance but on the other hand has to suffer aggravated form of trifling limitations associated with imperfect hydrodynamics and heat transfer behavior. Flow maldistribution is one of such limitation that exaggerates temperature nonuniformity across parallel microchannels leading to increase in maximum base temperature. Recently, variable...
-
Porous structures in aspects of transpirating cooling of oxycombustion chamber walls
PublikacjaA wet oxycombustion chamber, which must be effectively cooled due to high temperature evolved during the oxy-combustion process, by using the phenomena of Reynolds thermal transpiration and Navier slip velocity. Closures needed to execute mass flow rate in a microchannel, which should be treated as a single porous structure in the walls of the combustion chamber, have been obtained by applying a local 3D approach. The Navier-Stokes...
-
Air trapping problem during infiltration on the large areas
PublikacjaThe process of flow modeling in unsaturated porous medium is often found in many fields of sciences: geology, fluid mechanics, thermodynamics, microbiology or chemistry. Problem is relatively complicated due to complexity of the system which contains three phases: water, air and soil skeleton. The flow of water in such a medium can be described using two-phase (2PH) flow formulation, which accounts the inflow of air and water phases,...
-
Temperature Evolution, Material Flow, and Resulting Mechanical Properties as a Function of Tool Geometry during Friction Stir Welding of AA6082
PublikacjaThe friction stir welding process was simulated for joining AA6082 aluminum alloy with the use of the computational fluid dynamics method. Two different tool geometries were used—a tapered cylindrical pin (simple pin) and a hexagonal pin with grooves (complex pin). The analysis of the simulations performed was discussed in terms of temperature evolution during the process, total heat input, residual stresses and material flow....