Filtry
wszystkich: 2525
wybranych: 2261
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: backscattering coefficient
-
Application of thin diamond films in low-coherence fiber-optic Fabry Pérot displacement sensor
PublikacjaThe novel fiber-optic low coherence sensor with thin diamond films is demonstrated. The undoped and boron-doped diamond films were elaborated by the use of the microwave plasma enhanced chemical vapor deposition (μPE CVD) system. The optical signal from the Fabry–Pérot cavity made with the application of those thin films is sensitive to displacement. The sensor characterization was made in the range of 0–600 μm. The measurements...
-
INFLUENCE OF LOAD AND INFLATION PRESSURE ON THE TYRE ROLLING RESISTANCE
PublikacjaTyre load and inflation pressure are important factors controlling rolling resistance of road vehicles. The article presents results obtained in the Technical University of Gdańsk during laboratory and road measurements of different car tyres rolling on different pavements. The knowledge of rolling resistance characteristics is important for modelling car dynamics as well as fuel consumption. It is also necessary to establish proper...
-
High-temperature heat pumps – potential technology for heat recovery and production of process heat
PublikacjaIn the paper, the high temperature vapour compressor based heat pump with a selection of working fluids, both perspective and ecological ones, is considered. Such system is not yet commercially available on the market and in author’s opinion it has significant potential for various applications. In the presented analysis it was assumed that the heat source has a temperature of 50oC and the temperature lift is 60, 80 and 100K respectively....
-
Geotechnical characterization of soft soil deposits in Northern Poland
PublikacjaThis paper presents a geotechnical characterization of deltaic soft soil deposits in the Vistula Marshlands, northern Poland. It shows the limited applicability of organic soil classifications based on Cone Penetration Tests (CPTU) and Dilatometer Tests (DMT). None of the in-situ-based classifications correctly identifies peat. Analysis of the behaviour of contractive/dilative soil layers according to Robertson's updated classification...
-
MECHANICAL PROPERTIES OF BOTTOM ASH – DREDGED MATERIAL MIXTURES IN LABORATORY TESTS
PublikacjaBottom ash from EC Gdańsk and dredged material taken from the mouth of The Vistula were mixed to form an engineering material used for dike construction. Mixtures with different bottom ash content were tested in laboratory to determine its basic physical and mechanical properties. The optimum bottom ash–dredged material mixture, built in the corps of the test dike, contains 70% of ash. The optimum bottom ash content in the mixture...
-
On the Usefulness of the Generalised Additive Model for Mean Path Loss Estimation in Body Area Networks
PublikacjaIn this article, the usefulness of the Generalised Additive Model for mean path loss estimation in Body Area Networks is investigated. The research concerns a narrow-band indoor off-body network operating at 2.45 GHz, being based on measurements performed with four different users. The mean path loss is modelled as a sum of four components that depend on path length, antenna orientation angle, absolute difference between transmitting...
-
A Multifunctional Microwave Filter/Sensor Component Using a Split Ring Resonator Loaded Transmission Line
PublikacjaThis research is focused on the design and realiza2 tion of a microwave component with multifunctional filter/sensor 3 operation using a resonator-loaded transmission line (TL). It is 4 shown that while the structure acts as a bandstop filter, the 5 phase of the reflection coefficient from the loading resonator(s) 6 on a movable layer can be used for displacement sensing, thus 7 allowing for combining filtering with sensing in...
-
Nitrogen-Doped Diamond Film for Optical Investigation of Hemoglobin Concentration
PublikacjaIn this work we present the fabrication and characterization of a diamond film which can be utilized in the construction of optical sensors for the investigation of biological samples. We produced a nitrogen-doped diamond (NDD) film using a microwave plasma enhanced chemical vapor deposition (MWPECVD) system. The NDD film was investigated with the use of scanning electron microscopy (SEM), atomic force microscopy (AFM) and Raman...
-
Structural optimization of microjet array cooling system
PublikacjaThe single phase heat transfer from an upward facing, horizontal copper surface to arrays of impinging water jets was experimentally investigated. Experimental configuration allows for a free-surface unconfined jets flow. Square nozzles 50 × 100 μm arranged in four different geometries were used. Additionally, for the set of two jets array geometry was varied by adjusting the nozzle to nozzle distance. The area averaged heat transfer...
-
Volunteer Computing System Comcute with Smart Scheduler
PublikacjaIn this paper, a volunteer grid called Comcute is studied. Moreover, the harmony search scheduler is proposed. This scheduler has been designed for efficient using some resources of volunteer grid. The harmony search scheduler optimizes both a workload of a bottleneck computer and the cost of grid. Finally, some experiment outcomes have been discussed.
-
Tribo-Environment Dependent Chemical Modification of Sliding Interfaces in Ultrananocrystalline Diamond Nanowall Film: A Correlation with Friction and Wear
PublikacjaTribological properties of ultrananocrystalline diamond nanowall (UNCD NW) films were investigated quantitatively in three different and controlled tribo-environmental conditions, proposing the passivation and graphitization mechanisms. However, these mechanisms are rather complicated and possibly can be understood in well-controlled tribological conditions. It was shown that the friction and wear of these films were high in highPage 1...
-
Effects of Deck-Abutment Pounding on the Seismic Fragility Curves of Box-Girder Highway Bridges
PublikacjaEarthquake-induced pounding in bridges is a complex contact phenomenon in which the dynamic responses of structures, including collisions between deck and abutments, are strongly related to structural properties and earthquake excitation. The goal of this study is to develop and compare the seismic fragility curves of overall system and individual components of regular and irregular box-girder highway bridges in two cases: with...
-
Analysis of Accuracy of Modified Gradient Method in Indoor Radiolocalisation System
PublikacjaIn this paper a new method, called modified gradient method, has been proposed for position calculation on the basis of distance measurement in indoor environment. It is shown that well known method of position calculation such as Foy is inefficient in indoor environment. In this article is also described the indoor radiolocalisation system which was used for collecting distance measurements which were employed for further comparative...
-
On the lower smoothing bound in identification of time-varying systems
PublikacjaIn certain applications of nonstationary system identification the model-based decisions can be postponed, i.e. executed with a delay. This allows one to incorporate in the identification process not only the currently available information, but also a number of ''future'' data points. The resulting estimation schemes, which involve smoothing, are not causal. Assuming that the infinite observation history is available, the paper...
-
The Influence of Shear Deformation in analysis of plane frames
PublikacjaThe focus of the paper is to investigate the influence of shear deformation effect on the distribution of internal forces and frame deformation. To estimate shear deformation effect, the Timoshenko beam theory and the concept of shear deformation coefficients are used. Analysis of example frames gives the possibility to evaluate what have the most impact on size of shear deformation and in which type of frames the shear deformation...
-
Vapor correction of FTIR spectra – A simple automatic least squares approach
PublikacjaFTIR spectroscopy is one of the best techniques to study intermolecular interactions. However, such an application requires high quality spectra with as little noise as possible, which are often difficult to obtain. One of the main sources of unwanted interference is water vapor. Here a robust method is proposed for automatic, fast and reliable vapor correction of FTIR spectra. The presented least squares approach of vapor subtraction...
-
Estimators of covariance matrices in Msplit(q) estimation
PublikacjaThis paper proposes methods for the determination of covariance matrices of Msplit(q) estimators. The solutions presented here allow Msplit(q) estimation to be supplemented by the operations from the domain of accuracy analysis (especially that concerning estimators of parameters). Theoretical forms of covariance matrices of Msplit(q) estimators were established using the empirical influence functions and the equivalent covariance...
-
Hybrid Method Analysis of Unshielded Guiding Structures
PublikacjaA combination of mode matching, finite element methods and generalized impedance matrix is presented in a context of propagation problems for open guiding structures. The computational domain is divided into two regions: the first one is a circular cylinder containing whole guiding structure and the second one surrounds this artificial cylinder. The impedance matrix is calculated with the use of finite element method in the first...
-
Neurocontrolled Car Speed System
PublikacjaThe features of the synthesis of neural controllers for the car speed control system are considered in this article. The task of synthesis is to determine the weight coefficients of neural networks that provide the implementation of proportional and proportional-integralderivative control laws. The synthesis of controllers is based on an approach that uses a reversed model of the standard. A model of the car speed control system with...
-
Remote Health Monitoring of Wind Turbines Employing Vibroacoustic Transducers and Autoencoders
PublikacjaImplementation of remote monitoring technology for real wind turbine structures designed to detect potential sources of failure is described. An innovative multi-axis contactless acoustic sensor measuring acoustic intensity as well as previously known accelerometers were used for this purpose. Signal processing methods were proposed, including feature extraction and data analysis. Two strategies were examined: Mel Frequency Cepstral...
-
Porous Phantoms Mimicking Tissues – Investigation of Optical Parameter Stability Over Time
PublikacjaIn terms of optical parameters, optical phantoms can now replace live tissues and be used to validate optical measurement methods. Therefore, whether these parameters would be maintained after storage for 6 months was examined. The absorption and scattering coefficients were obtained from the measured transmittance and reflectance measurements taken 6 months apart and then compared. All of the measurements were conducted using...
-
Annihilation rates of low-energy positron scattering from simple diatomic molecules
PublikacjaWe discuss the calculations of Zeff coefficients for a series of diatomic molecules over the range of energies below the positronium formation. During the development of a general code for polyatomic, nonlinear molecules colliding with positrons, it was discovered that the earlier one, employed only for diatomic molecules, had an error. The error is corrected and the corrected results are presented here. We also discuss a way of...
-
How to render FDTD computations more effective using agraphics accelerator.
PublikacjaGraphics processing units (GPUs) for years have been dedicated mostly to real time rendering. Recently leading GPU manufactures have extended their research area and decided to support also graphics computing. In this paper, we describe an impact of new GPU features on development process of an efficient finite difference time domain (FDTD) implementation.
-
Practical Method for the Preparation of 2,2-Dimethyl-5- {aryl[(hetero)aryl]methyl}-1,3-dioxane-4,6-diones: Synthesis and Mechanistic Study
PublikacjaAn efficient practical synthetic procedure has been developed for the synthesis of 2,2-dimethyl-5-{aryl[(hetero)aryl]methyl}- 1,3-dioxane-4,6-diones through Friedel–Crafts alkylation. The scope and limitation of the reaction of 2,2-dimethyl-5-arylidene-1,3-dioxane- 4,6-diones with π-excess aromatic systems have been delineated.
-
Analysis of Learning Outcomes in Medical Education with the Use of Fuzzy Logic
PublikacjaThe national curricula of the EU member states are structured around learning outcomes, selected according to Bloom’s Taxonomy. The authors of this paper claim that using Bloom’s Taxonomy to phrase learning outcomes in medical education in terms of students’ achievements is difficult and unclear. This paper presents an efficient method of assessing course learning outcomes using Fuzzy Logic.
-
Analysis of IPv6 handovers in IEEE 802.16 environment
PublikacjaThe second generation of WiMAX solutions, based on IEEE 802.16-2005 standard, offers limited mobility support. Unfortunately, after quickly changing the point of attachment on the WiMAX data link layer (DLL), very slow and inefficient IPv6 reconfiguration takes place. Delays introduced by automatic configuration (DHCPv6 and IPv6 protocols) and Mobile IPv6 can easily diminish or even render useless all benefits gained using the...
-
Health System Efficiency in European Countries: Network Data Envelopment Analysis Approach
PublikacjaPurpose: The article's main aim is to investigate the effectiveness of health systems in European countries based on EUROSTAT data. A comparative analysis of the health systems' effectiveness in different countries is based on their improvement (reform), using the best practices approach. Design/Methodology/Approach: The network DEA model and a slack-based model (NDEA – SBM) are used. A non-oriented model is used. The research...
-
The impact of material degradation on the resistance and reliability of truss structures
PublikacjaThe paper analyses limit load-carrying capacity and buckling load of truss towers used to support high voltage power lines. The analysed typical structure was subjected to characteristic loads and their combinations. The results were applied to assess structural resistance with regard to steel corrosion in the long-term operation. The extent of structural deterioration was assessed due to Young's modulus decrement in the course...
-
Thermoelectric properties of bismuth-antimony-telluride alloys obtained by reduction of oxide reagents
PublikacjaThe BieSbeTe alloys with different Bi/Sb/Te ratio were fabricated by an innovative method. For that purpose the oxide reagents were melted at high temperature, then quenched to form pellets, milled to a powder and finally reduced in hydrogen at various temperatures. Complex structures consisting of connected thin layers forming a continuous path between nano- and micrometer size grains have been obtained. The electrical conductivity,...
-
Modeling bioaugmentation with nitrifiers in membrane bioreactors
PublikacjaBioaugmentation with nitrifiers was studied using two pilot-scale membrane bioreactors, with the purpose of assessing the suitability of state-of-the-art activated sludge models (ASMs) in predicting the efficiency of bioaugmentation as a function of operating conditions. It was demonstrated that the temperature difference between seeding and seeded reactors (ΔT) affects bioaugmentation efficiency. Experimental data were accurately...
-
Foreign Entry Modes of High-tech Firms in Poland
PublikacjaThe main objective of the article is to present the role and importance of foreign entry modes in internationalization process and their key determinants. Research methods: A quantitative research design was used. A survey was conducted on the sample of 263 firms operating in...
-
Fluctuation-Enhanced Sensing for Biological Agent Detection and Identification
PublikacjaPrzedstawiono wcześniejsze wyniki badań dotyczące trzech różnych sposobów wykrywania obecności substancji biologicznych za pomocą zjawisk fluktuacyjnych: 1) wirusów wnikających do komórek, 2) zapachów emitowanych przez mikroby, 3) rozkładu widma i wartości chwilowych szumów podczas rozpraszania światła używanego do wykrywania zarodników na podstawie wyznaczenia współczynnika dyfuzji opisująceo ich ruch.We survey and show our earlier...
-
Study on the Influence of an Axial Distance Between Rotors on a Performance of a Small Counter-Rotating Wind Turbine
PublikacjaIn this paper, results of the investigation on the performance of a small counter-rotating wind turbinehas been presented. Computational Fluid Dynamics methodshave been used forwind turbine simulations. Rotors representation were introduced into computational domain by means of Actuator Line Model. Influence of an axial distance of CRWTrotorshas been investigated. In all studied configurations rotors were counter-rotating...
-
X-Ray Diffraction, Mössbauer Spectroscopy and Magnetoelectric Effect Studies of Multiferroic Bi5Ti3FeO15 Ceramics
PublikacjaBi5Ti3FeO15 ceramics belongs to multiferroic class of materials. In this work it was prepared by solid-state sintering method and investigated by X-ray diffraction, Mössbauer spectroscopy, and magnetoelectric effect measurements. As it was proved by X-ray diffraction studies the single-phase Bi5Ti3FeO15 compound was obtained. The Mössbauer investigations revealed paramagnetic character of the compound at room temperature as well...
-
Analysis of the macrostructure of the fuel spray atomized with marine engine injector
PublikacjaOne of the main problem influencing the combustion process in the cylinder of the marine engine is an fuel spray phenomena. The parameters describing the shape of the fuel spray are named macro parameters. This article presents the research results of the macrostructure parameters of the fuel spray atomized with the marine engine injector. The research were carried out by optical visualization measurement method of Mie scattering....
-
Crystal structure and physical properties of a novel ternary compound La15MoxGe9
PublikacjaWe present the synthesis, structural characterization and physical properties measurements of a new compound, La15MoxGe9 in Mn5Si3-type derived structure with interstitial Mo. The sample was synthesized by arc-melting method. La15MoxGe9 crystallizes in non-centrosymmetric hexagonal structure P63mc (#186) with lattice parameters a = b = 15.495(5) Å and c = 6.917(2) Å. The refinement on single X-ray diffraction data show that interstitial...
-
ZnO ALD-Coated Microsphere-Based Sensors for Temperature Measurements
PublikacjaIn this paper, the application of a microsphere-based fiber-optic sensor with a 200 nm zinc oxide (ZnO) coating, deposited by the Atomic Layer Deposition (ALD) method, for temperature measurements between 100 and 300°C, is presented. The main advantage of integrating a fiber-optic microsphere with a sensing device is the possibility of monitoring the integrity of the sensor head in real-time, which allows for higher accuracy during...
-
Structure and thermoelectric properties of nickel-doped copper selenide synthesised in a hydrogen atmosphere
PublikacjaNickel-doped copper selenide—Cu2-xNixSe (x = 0; 0.01; 0.02; 0.03)—materials with high thermoelectric properties were synthesised through reduction of reagents in hydrogen. The impact of the nickel content on both the microstructure and thermoelectric properties was examined. The nickel-doped samples’ microstructure differed significantly from pristine copper selenide. Besides Cu2Se, copper precipitations were present in the materials....
-
Cargo ships heat demand - operational experiment
PublikacjaThe paper presents the results of an experiment conducted on two cargo ships – a 5300 TEU container with a steam heating system and a 7500 dwt general cargo ship with a thermal oil system. On both ships research has been carried out using specially designed measuring equipment. After gathering data about flow velocity and temperatures (steam/ cooling water/ thermal oil/ seawater/ outside air), calculations have been done, resulting...
-
Estimation of the Ultimate Strength of FRP Strips-to-Masonry Substrates Bond
PublikacjaFiber-Reinforced Polymers (FRP) were developed as a new method over the past decades due to their many beneficial mechanical properties, and they are commonly applied to strengthen masonry structures. In this paper, the Artificial Neural Network (ANN), K-fold Cross-Validation (KFCV) technique, Multivariate Adaptive Regression Spline (MARS) method, and M5 Model Tree (M5MT) method were utilized to predict the ultimate strength of...
-
Partition of friction heat between sliding semispaces due to adhesion-deformational heat generation
PublikacjaAnalytical expressions of heat-partition coefficient and contact temperatures for two sliding semispaces with account for adhesion-deformational heat generation and contact heat exchange have been obtained. The rate of deformational heat generation is assumed to decay exponentially with increase of distance from the interface. It has been shown that heat-generation configuration and the intensity of contact heat exchange have impact...
-
An optimal form of the finite element mass matrix in the analysis of longitudinal vibrations of rods
PublikacjaIn this paper, an attempt is made to find the optimal form of the mass matrix of a rod finite element, which allows one to obtain the smallest errors in the longitudinal frequency determination of natural vibrations of any boundary conditions within the whole range of determined frequencies. It is assumed that the mass matrix can be treated as a linear combination of the consistent and diagonal matrices. Based on analytical considerations,...
-
Performance of the very high-temperature heat pump with low GWP working fluids
PublikacjaTraditional heat pumps are a very attractive pro-ecological solutions for a number of applications, including providing of heating or heat recovery from industrial processes. The application range of heat pumps could be greatly enlarged when the operating temperature would be increased to 130-150°C and/or the temperature lift can be increased to 50-100 K. In the paper, the very high temperature vapour-compressor based single stage...
-
An evaluation of sucrose as a possible contaminant in e-liquids for electronic cigarettes by hydrophilic interaction liquid chromatography–tandem mass spectrometry
PublikacjaThe influence of sucrose combustion products on smoking and nicotine addiction is still controversial because the presence of the sucrose may be treated as a source of aldehydes and organic acids. In e-liquids used as refills for electronic cigarettes, which are made primarily of poly(propylene glycol), glycerine and ethanol, sucrose may be present at trace levels, and its impact on mainstream smoke formation, and hence on human...
-
Wybrane aspekty modelowania uderzenia pojazdem dźwigara wiaduktu
PublikacjaW pracy przedstawiono różne zagadnienia związane z uderzeniem pojazdu w dźwigar wiaduktu. Omówiono wybór modelu obliczeniowego, na podstawie porównania wyników dla modelu dźwigara zespolonego, modelu dźwigara stalowego oraz modelu wiaduktu. Następnie opisano model dźwigara zespolonego zastosowany w analizie MES oraz metodę wyznaczania współczynników tłumienia Rayleigha. Symulację numeryczną uderzenia dźwigara wiaduktu przez koparkę...
-
The Efficiency of Public and Private Higher Education Institutions in Poland
PublikacjaChanges introduced to Poland’s education system in 2011 and 2014 amid efforts to adjust it to the needs of the labour market had an effect on the country’s institutions of higher learning. This paper provides an analysis of the efficiency of public and private Polish universities and examines the impact of selected factors in the years that followed. To estimate this efficiency, a Banker, Charnes and Cooper (BCC) model of the...
-
An intelligent cellular automaton scheme for modelling forest fires
PublikacjaForest fires have devastating consequences for the environment, the economy and human lives. Understanding their dynamics is therefore crucial for planning the resources allocated to combat them effectively. In a world where the incidence of such phenomena is increasing every year, the demand for efficient and accurate computational models is becoming increasingly necessary. In this study, we perform a revision of an initial proposal...
-
Electricity generation from rapeseed straw hydrolysates using microbial fuel cells
PublikacjaRapeseed straw is an attractive fuel material for microbial fuel cells (MFCs) due to its high content of carbohydrates (more than 60% carbohydrates). This study has demonstrated that reducing sugars can be efficiently extracted from raw rapeseed straw by combination of hydrothermal pretreatment and enzymatic hydrolysis followed by utilization as a fuel in two-chamber MFCs for electrical power generation. The most efficient method...
-
Unsupervised machine-learning classification of electrophysiologically active electrodes during human cognitive task performance
PublikacjaIdentification of active electrodes that record task-relevant neurophysiological activity is needed for clinical and industrial applications as well as for investigating brain functions. We developed an unsupervised, fully automated approach to classify active electrodes showing event-related intracranial EEG (iEEG) responses from 115 patients performing a free recall verbal memory task. Our approach employed new interpretable...
-
Verification of GNSS Measurements of the Railway Track Using Standard Techniques for Determining Coordinates
PublikacjaThe problem of the reproduction of the railway geometric layout in the global spatial system is currently solved in the form of measurements that use geodetic railway networks and also, in recent years, efficient methods of mobile positioning (mainly satellite and inert). The team of authors from the Gdańsk University of Technology and the Maritime University in Gdynia as part of the research project InnoSatTrack is looking for...