Filtry
wszystkich: 888
wybranych: 674
-
Katalog
- Publikacje 674 wyników po odfiltrowaniu
- Czasopisma 19 wyników po odfiltrowaniu
- Osoby 23 wyników po odfiltrowaniu
- Wynalazki 2 wyników po odfiltrowaniu
- Projekty 15 wyników po odfiltrowaniu
- Laboratoria 2 wyników po odfiltrowaniu
- Kursy Online 37 wyników po odfiltrowaniu
- Wydarzenia 2 wyników po odfiltrowaniu
- Dane Badawcze 114 wyników po odfiltrowaniu
Filtry wybranego katalogu
Wyniki wyszukiwania dla: MICRO/NANOMECHANICS
-
Sources and fate of microplastics in marine and beach sediments of the Southern Baltic Sea—a preliminary study
PublikacjaMicroplastics’ sources and fate in marine bottom and beach sediments of strongly polluted Baltic Sea have been investigated.Microplastics were extracted using sodium chloride. Their qualitative identification was conducted using micro-Fourier-transform infrared spectroscopy (μFT-IR).
-
Impact of the glazed roof on acoustics of historic interiors
PublikacjaThe paper discusses the adverse acoustic phenomena occurring in the semi-open interiors (courtyards, yards) covered with a glass roof. Particularly negative is the rever-beration noise, which leads to the degradation of the utility functions of the resulting spaces. It involves the drastically reducing the intelligibility of speech, loss of natural sounding of music, problems with the sound system, as well as disturbances in the...
-
Production and Properties of the Porous Layer Obtained by the Electrochemical Method on the Surface of Austenitic Steel
Publikacja: The growing demand for implants has seen increasing interest in the introduction of new technologies and surface modification methods of metal biomaterials. This research aimed to produce and characterize a porous layer grown on austenitic stainless steel 316L, obtained via the anodization process near the micro-arc oxidation, i.e., low voltage micro-arc oxidation (LVMAO). The discussed layer significantly influences the properties...
-
Hydrological responses to large-scale changes in land cover of river watershed: Review
PublikacjaDespite many studies on the hydrological responses to forest cover changes in micro and mesoscale watersheds, the hydrological responses to forest cover alterations and associated mechanisms through the large spatial scale of the river watershed have not been comprehensively perceived. This paper thus reviews a wide range of available scientific evidence concerning the impacts exerted by the forest removal on precipitation, water...
-
Possibilities of Increasing the Overall Efficiency of Gas-steam CHP Microplant
PublikacjaThe paper presents ways to increase the efficiency of a gas-steam micro power plant by modifying the cycle combination. The modification consists in partial release of the fluid downstream of the gas turbine and using it for ORC fluid overheating and evaporation. Advantages of this solution over the simplest gas and steam cycles’ combination are demonstrated.
-
Innowacyjny moduł ultradźwiękowy systemu monitoringu technicznego mostu podwieszonego w Rzeszowie
PublikacjaW artykule przedstawiono system monitoringu technicznego konstrukcji mostu podwieszonego nad rzeką Wisłok. System będzie wyposażony w dodatkowy moduł ultradźwiękowy umożliwiający śledzenie degradacji mechanicznej betonu w pylonie mostu. Wczesne wykrywanie stref mikropęknięć, przed pojawieniem się widocznych rys, umożliwia monitorowanie amplitud propagującej fali ultradźwiękowej oraz analizę sygnałów w dziedzinie częstotliwości.
-
Zmiany temperatury elementów układu wykonawczego docierarki jednotarczowej
PublikacjaPrzedstawiono wyniki badań docierania powierzchni płaskich na docierarce jednotarczowej. Praca stanowi wstęp do badań zagadnienia wzrostu temperatury elementów układu wykonawczego obrabiarki. Eksperymenty przeprowadzono na docierarce jednotarczowej ABRALAP 380 przy użyciu kamery termowizyjnej MICRO-EPSILON/TM 160.
-
Structurally well-defined functionalized polyolefins and graft copolymers thereof as bitumen modifiers
PublikacjaHere we demonstrate the application of hydroxyl-functionalized propylene-based copolymers, poly(propylene-co-1-hexene-co-10-undecen-1-ol) (FPP) and poly(styrene-co-maleic anhydride) (SMA) graft copolymers derived thereof, poly(propylene-co-1- hexene-graft-styrene-co-maleic anhydride) (FPP-g-SMA) as bitumen modifiers. The FPP samples were synthesized via solution copolymerization, while FPP-g-SMA products were obtained via transesterification...
-
Ecotoxicological equilibria of triclosan inMicrotox, XenoScreen YES/YAS, Caco2, HEPG2 and liposomal systems are affected by the occurrence of other pharmaceutical and personal care emerging contaminants
PublikacjaContaminants of emerging concernmay be considered as any chemicals or factorswhose unintended continuous release and persistence in the environmentmay lead to any observable undesirable response of living beings. Still not much is known on reciprocal toxicological impact of given chemicals when present in binary or more complex mixtures. In thiswork, an attemptwas thus undertaken to study the impact of butylparaben,methylparaben and...
-
Chemical, Aroma and Pro-Health Characteristics of Kaffir Lime Juice—The Approach Using Optimized HS-SPME-GC-TOFMS, MP-OES, 3D-FL and Physiochemical Analysis
PublikacjaThe study aimed to provide the chemical, aroma and prohealth characteristics of the kaffir lime juice. A procedure using solid-phase microextraction with gas chromatography (SPME-GC-TOFMS) was optimized and validated for the determination of terpenes of kaffir lime. Main physicochemical parameters: pH, vitamin C, citric acid and °Brix were evaluated. Micro- and macro elements were determined using microwave plasma optic emission...
-
Preliminary Identification of Quantitative Factors Determining the Duration of Court Proceedings in Commercial Cases
PublikacjaPurpose: The aim of the article was to identify factors that are linear combinations of the variables under scrutiny that affect the duration of court proceedings. Design/Methodology/Approach: This research was conducted on commercial cases, based on the Principal Components Analysis (PCA). The original variables were grouped into factors that are correlated with each other. The Kaiser Criterion (own value >1) was chosen as the...
-
The Changing Nature of In‐Between Spaces in the Transformation Process of Cities
PublikacjaIn the in‐between spaces of cities, there are many problems of various nature and scale: functional, spatial, economic, environmental, visual, and social. There are also some hidden potentials that can be activated. The aim of the article is to explore the possibilities of solving existing problems and to show the possibilities of using the potentials of in‐between spaces with regard to the changing nature of a city. The article,...
-
Meso‐scale analyses of size effect in brittle materials using DEM
PublikacjaThe paper describes numerical meso-scale results of a size effect on strength, brittleness and fracture in brittle materials like concrete. The discrete element method (DEM) was used to simulate the size effect during quasi-static splitting tension with the experimental-based meso-structure. The two-dimensional (2D) calculations were carried out on concrete cylindrical specimens with two diameters wherein two different failure...
-
Application of Rapid Prototyping technology in the manufacturing of turbine blade with small diameter holes
PublikacjaThe article presents the possibilities of using Rapid Prototyping (RP) technology in the manufacturing of turbine blades with small diameter holes. The object under investigation was gas turbine blade with small diameter cooling holes and holes for generating longitudinal vortices. A turbine blade model was produced by means of Direct Metal Laser Sintering (DMLS) technology and subsequently validated in terms of detection and accuracy...
-
A two-scale numerical approach to granular systems
PublikacjaW artykule zaprezentowano wyniki dwuskalowego numerycznego podejścia do materiałów granulowanych. Na poziomie mikro materiał był modelowany przy zastosowaniu metody elementów dyskretnych, natomiast na poziomie makro przy zastosowaniu metody elementów skończonych na bazie macierzy sztywności wyznaczonej na podstawie naprężeń i odkształceń na poziomie mikro.
-
Possibilities of heat transfer augmentation in heat exchangers with minichannels for marine applications
PublikacjaIn the paper, new trends in development of microchannel heat exchangers are presented. The exchangers developed in this way can be applied in marine applications. Main attention was focused on heat exchangers design with reduced size of passages namely based on microchannels. In our opinion future development of high power heat exchangers will be based on networks micro heat exchangers.
-
Czy korporacyjna kultura CSR może być wzorcem dla małych i średnich przedsiębiorstw?
PublikacjaArtykuł pokazuje specyfike realizacji idei firmy społecznie odpowiedzialnej w firmach mikro i firmach dużych - podobieństwa i różnice w sposobie pojmowania idei,specyfikę działań.Firmy duże - koncerny, mając diametralnie różną strukturę od firm mikro, działając w innym otoczeniu ekonomicznym, w swojej działalności borykają się ze zgoła różnymi, nie dającymi się porównać problemami. Stąd ich pojmowanie i realizacja programów CSR...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublikacjaThe paper presents the results of a design analysis of a microturbine for a cogeneration micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3 kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attentionwas paid...
-
Incorporation of nitrogen in diamond films – A new way of tuning parameters for optical passive elements
PublikacjaThis paper investigates the impact of nitrogen incorporation in diamond films for the construction of an interferometric sensor to measure displacement. Diamond films with different nitrogen levels (0–5%) were deposited on silicon substrates by microwave plasma enhanced chemical vapor deposition. The structural characteristics of these samples are characterized using scanning electron microscopy (SEM), atomic force microscopy (AFM), confocal...
-
Komputerowa analiza wielkości mikroziaren ściernych
PublikacjaPrzedstawiono skomputeryzowaną analizę wielkości i kształtu mikroziaren ściernych przy użyciu specjalnego oprogramowania MultiScan v.6.08 oraz zautomatyzowane pomiary z wykorzystaniem analizatora laserowego Analysette 22 Micro Tec mikroziaren czarnego węglika krzemu o numerze F32/29. Dokonano przeglądu konstrukcji najnowszych analizatorów czołowych producentów światowych.
-
The concept of capillary forces supported evaporator for application to domestic ORC unit
PublikacjaIn the paper presented are studies on the investigation of the capillary forces effect inducted in the porous structure of a loop heat pipe. The potential application of such heat exchanger is for example an evaporator of the domestic micro CHP unit. Preliminary analysis of the results indicates water as having the best potential, however taking into account all issues it can be said that the best effect is obtained using ethanol.
-
Electrophoretic Deposition and Characteristics of Chitosan–Nanosilver Composite Coatings on a Nanotubular TiO2 Layer
PublikacjaThe surface treatment of titanium implants has been applied mainly to increase surface bioactivity and, more recently, to introduce antibacterial properties. To this end, composite coatings have been investigated, particularly those based on hydroxyapatite. The present research was aimed at the development of another coating type, chitosan–nanosilver, deposited on a Ti13Zr13Nb alloy. The research comprised characterization of the...
-
Co zrobić z nieużywaną wieżą ciśnień? Studium historyczno-koncepcyjne (część II)
PublikacjaDruga część artykułu przedstawia obliczenia parametrów pracy, jakich można się spodziewać, realizując koncepcję mikro-elektrowni szczytowo-pompowej w oparciu o adaptację nieczynnej wieży ciśnień stanowiącej część budynku Laboratorium Maszynowego. Przedstawiona została także analiza możliwości współpracy z istniejącą instalacją fotowoltaiczną w kierunku uzyskania kompletnego mikro-systemu energetycznego.
-
Two - scale model for concrete beams subjected to three point bending - numerical analyses and experiments
PublikacjaArtykuł omawia dwu-skalowe podejście do betonu przy wykorzystaniu połączonych modeli. Metodę elementów skończonych zastosowano na poziomie makro. Na poziomie mikro zastosowano metodę elementów dyskretnych. Macierz sztywności wyznaczono na podstawie tensora naprężeń wyznaczonego w skali mikro. Wyniki numeryczne dw-skalowe porównano z wynikami dyskretnymi dla całego obszaru.
-
A two-scale (FEM-DEM) approach for concrete
PublikacjaArtykuł omawia dwu-skalowe podejście do betonu przy wykorzystaniu modelu Mes i DEM. Metodę elementów skończonych zastosowano na poziomie makro. Na poziomie mikro zastosowano metodę elementów dyskretnych. Macierz sztywności wyznaczono na podstawie tensora naprężeń wyznaczonego w skali mikro. Wyniki numeryczne dwusalowe porównano z wynikami dyskretnymi dla całego obszaru.
-
Endangering of Groundwater on the Municipal Intakes in Gdańsk
PublikacjaGroundwater from the Quaternary aquifer on the marine terrace in Gdańsk has been exploited for almost a century, supplying the town with water of good quality. However intensive exploitation in the past and development of the urban area influenced the chemical composition of the water. Hydrogeochemical background for such ions as chlorine, sulphate and ammonia has changed and also some organic micro compounds appeared in single...
-
Investigation of the influence of capilary effect on operation of the loop heat pipe
PublikacjaIn the paper presented are studies on the inestigation of the capillary forces effect inducted in the porous structure of a loop heat pipe using water and ethanol ad test fluids. The potential application of such effects is for example in the evaporator of the domestic micro-CHP unit, where the reduction of pumping power could be obtained. Preliminary analysis of the results indicates water as having the best potential for developing...
-
Energy consumption estimation of low-power devices using an integrating coulombmeter
PublikacjaThe main problem in designing devices powered with Energy Harvesting is an estimation of energy demand of low-power devices as well as quantity of energy provided by the selected energy transducer in the assumed work conditions. Due to the work characteristic of each block of the device and properties of the measured signal, measurement is not trivial. The paper presents the proposal of the micro-charge measurement device based...
-
Incorporation of nitrogen in diamond films - A new way of tuning parameters for optical passive elements
PublikacjaThis paper investigates the impact of nitrogen incorporation in diamond films for the construction of an interferometric sensor to measure displacement. Diamond films with different nitrogen levels (0–5%) were deposited on silicon substrates by microwave plasma enhanced chemical vapor deposition. The structural characteristics of these samples are characterized using scanning electron microscopy (SEM), atomic force microscopy...
-
Wpływ parametrów strugi paliwa wtryskiwanego do cylindra silnika okrętowego na początkową fazę rozpylania
PublikacjaPrzedmiotem rozprawy jest analiza procesu wtrysku oleju napędowego do cylindra silnika okrętowego z zapłonem samoczynnym i bezpośrednim wtryskiem paliwa. Analiza tego zagadnienia została przeprowadzona w aspekcie wpływu makro parametrów strugi na początkową fazę rozpylania oleju napędowego. Celem niniejszej pracy jest określenie wpływu współczynnika L/D (długość otworu/średnica) otworu wylotowego wtryskiwacza na zmianę charakterystyki...
-
A Set of Low-power Microcontroller-based Modules Used for Testing of Small Energy Measurement Methods
PublikacjaEstimation of energy consumption of low-power devices is not widely discussed in the scientific literature, but this topic is getting more and more popular. Evaluation process of newly developed methods and instrumentation requires carefull treatment. In order to fulfill this niche, the set of micro-power microcontroller based devices was proposed. The devices represent typical energy consuption profiles and allow experimental verification...
-
Analysis and Evaluation of the Working Cycle of the Diesel Engine
PublikacjaThe paper presents a proposal to apply a quantitative evaluation of the diesel engine with regard to the phenomena occurring during of a working cycle. The proposed procedure when analyzing test results from diesel engine is an attempt to transfer an engine activity evaluation methods in the operational time scale (exploit time), eg. in hours, to the micro-scale (dynamic time) relating only to the execution time of one (several)...
-
On various modelling approaches to real-time visualisation of blood flow
PublikacjaThis paper reviews various modelling approaches to real-time visualisation of blood flow. These include classic, macroscale approach based on the momentum conservation equation together with a proper constitutive equation. Moreover, modern micro- and mesoscale approaches, such as molecular dynamics and dissipative particle dynamics, are discussed. Advantages and disadvantages of the discussed methods are highlighted with particular...
-
Edu Inspiracje WZiE: Czy mikrokwalifikacje i cyfrowe odznaki zmienią oblicze edukacji?
PublikacjaMikrokwalifikacje nazywane również mikropoświadczeniami (micro- -credentials), mówiąc prostymi słowami, są cyfrowymi certyfikatami potwierdzającymi uzyskanie umiejętności, wiedzy lub kompetencji. To dowody ukończenia mniejszych (niż określają np. dyplomy uniwersyteckie) form edukacyjnych takich jak kursy e-learningowe, warsztaty lub szkolenia. Pozwalają też szybko pokazać to, co umiemy, i przedstawić w postaci atrakcyjnego cyfrowego...
-
Comparative modeling of shear localization in granular bodies with FEM and DEM
PublikacjaThe intention of the paper is to compare the calculations of shear zones in granular bodies using two different approaches: a continuum and a discrete one. In the first case, the FEM based on a micro-polar hypoplastic constitutive law was used. In the second case, the DEM was taken advantage of, where contact moments were taken into account to model grain roughness. The comparative calculations were performed for a passive case...
-
Grain type and size of particulate matter from diesel vehicle exhausts analysed in transmission electron microscopy
PublikacjaThe aim of this research was to apply a simple and quick method of size and shape characterization by TEM to diesel exhaust particles from large-capacity, high-performance trucks. Particulate matter (PM) samples were collected while the engines were idling. It was found that PM from vehicle exhaust emissions can be divided into three groups: soot, irregular-shaped particles and circular particles. Irregular-shaped particles and...
-
The new concept of capillary forces aided evaporator for application in domestic organic rankine cycle
PublikacjaThis paper presents studies on the possibility of applying capillary forces induced in the porous structure to a modern design of evaporator. The potential application of such heat exchanger is for example an evaporator of the domestic micro combined heat and power (CHP) unit. One of the problems in the micro-CHP is excessive demand for pumping power. The proposed design helps in overcoming that issue. In the evaporator outlined...
-
STABILITY OF THE INNER SLOPE OF THE POLISH DREDGDIKES RESEARCH DIKE AT STATIONARY FLOW
PublikacjaFor long duration of the flood the water table can appear on the slope with a problem of out-wash in the case of sand type dike. If the dike corps is covered with less permeable layer some additional push-off forces and shearing can rise in the cover. In both cases the micro stability of the inner slope should be considered at normative high water for homogeneous sand type dike or sand type dike with less permeable covers. The...
-
Technologia biomems - przegląd zastosowań
PublikacjaThe paper reviews the issues related to technology, MEMS (Micro-Electro Systems-Mechanical) in the context of applications in biotechnology and biomedical systems. Systems of this type, with applications in biology and medicine, have the name of our common BioMEMS systems. This pertains to a wide range of technology BioMEMS. The aim of this study is to determine future medical MEMS microphones with particular emphasis on their...
-
Investigations of size effect in concrete at aggregate level - experiments and calculations results using discrete element method
PublikacjaSize effect is a fundamental phenomenon in concrete. It is characterised by decreasing strength and increasing brittleness of concrete with increasing size. The thesis includes experimental and theoretical elements. The main goal of the thesis were investigations of a size effect at the aggregate level by taking fracture into account with the discrete element method (DEM) for various failure modes. Comprehensive experiments on...
-
Efficient model order reduction for FEM analysis of waveguide structures and resonators
PublikacjaAn efficient model order reduction method for three-dimensional Finite Element Method (FEM) analysis of waveguide structures is proposed. The method is based on the Efficient Modal Order Reduction (ENOR) algorithm for creating macro-elements in cascaded subdomains. The resulting macro-elements are represented by very compact submatrices, leading to significant reduction of the overall number of unknowns. The efficiency of the model...
-
Numerical Modelling of Shear Localization in Granular Bodies using MPM and Non-local Hypoplasticity
PublikacjaThe paper deals with modelling of shear localization in granular bodies by means of an enhanced hypoplastic constitutive model and material point method (MPM). The calculations were carried out for plane strain compression of non-cohesive sand. In order to properly capture the width and inclination of shear zones, the constitutive model was enriched by a characteristic length of micro-structure by means of a non-local theory....
-
Ribosomal intergenic spacer analysis as a tool for monitoring methanogenic archaea changes in an anaerobic digester
PublikacjaThe applicability of a newly-designed PCR primer pair in examination of methanogenic Archaea in a digester treating plant biomass was evaluated by Ribosmal Intergenic Spacer Analysis (RISA). To find a suitable approach, three variants of RISA were tested: (1) standard, polyacrylamide gel-based, (2) automated, utilized capillary electrophoresis (GA-ARISA), and (3) automated microfluidics-based (MF-ARISA). All three techniques yielded...
-
Voltage variations and their reduction in a rural low-voltage network with PV sources of energy
PublikacjaRenewable sources of energy (RES), especially photovoltaic (PV) micro-sources, are very popular in many countries. This way of clean power production is applied on a wide scale in Poland as well. The Polish legal regulations and tariffs specify that every prosumer in a low-voltage network may feed this network with a power not higher than the maximum declared consumed power. In power networks with RES, the voltage level changes...
-
Numerical analysis of high temperature minichannel heat exchanger for recuperative microturbine system
PublikacjaConsidering the development of energy sector, distributed small-scale power generation, e.g., gas micro-CHP, is attracting considerable interest. In such installations, the heat exchanger is one of the key components possessing a significant influence on overall performance. Most studies concentrate on units operating below 900C, which do not fulfil the requirements of gas micro-CHP. Therefore, there remains a challenge to design...
-
Elektro-magnetyczna metoda badania procesu degradacji stali austenitycznych
PublikacjaBadano próbki ze stali A304 oraz A347 po eksploatacji oraz próbki poddane deformacji plastycznej. Przyjęto założenie, że degradacja prowadzi do wzrostu zawartości fazy ferrytycznej w tych stalach, co może być wykorzystane do oceny stopnia degradacji. Artykuł prezentuje wyniki wstępnych badań nad możliwością wykrycia relatywnie niewielkich koncentracji fazy ferrytycznej. Próbki w początkowym stadium procesu degradacji (wycięte z...
-
Improvement of microstructure and mechanical properties of high dense sic ceramics manufactured by high-speed hot pressing
PublikacjaNon-oxide ceramics possess high physical-mechanical properties, corrosion and radiation resistance, which can be used as a protective materials for radioactive wastes disposal. The aim of the present study was the manufacturing of high density SiC ceramics with advanced physical and mechanical parameters. The high performance on the properties of produced ceramics was determined by the dense and monolithic structure. The densified...
-
THE USE OF THE Ti-13Zr-13Nb ALLOY POWDER FOR MANUFACTURING OF PROSTHETIC PARTS BY SELECTIVE LASER MELTING
PublikacjaThe 3D printing is a manufacturing technique belonging to the additive methods able to prepare the designed parts for various purposes. The present reasearch was aimed to fabricate the prosthetic foundations and bridges made of the new Ti-13Zr-13Nb alloy by the selective laser melting (SLM) of a metal powder. The scanning electron examinations and micro scanning tomography were used to investigate the surface quality and intrinsic...
-
Art and Healthcare - Healing Potential of Artistic Interventions in Medical Settings
PublikacjaThe stereotype of a machine for healing seems to be well rooted in common thinking and social perception of hospital buildings. The technological aspect of healthcare architecture has been influenced for several years by three major factors. The first is linked to the necessity of providing safety and security in the environment of elevated epidemiological risk. The second concerns the need for incorporating advanced technology...
-
Organisational culture and change management in courts, based on the examples of the Gdańsk area courts
PublikacjaABSTRAKT Background. Courts are by definition bureaucratic, hierarchical organisations, epitomised by low levels of networking potential, which basically lack mechanisms of information exchange, or those of sharing information both at the level of the organisation of the justice system (the macro scale) and within a given court (the micro scale). Research aims. The aims of this article was implementing modern management methods...