Filtry
wszystkich: 1000
Wyniki wyszukiwania dla: DISPLACEMENTS OF CHIMNEY
-
NEW SOLUTIONS FOR THE SOLAR CHARGE CONTROLLERS DESIGN FOR OBTAINING TRUE MPP IN PARTLY SHADED PV MODULES
PublikacjaSoft shading sources such as tree limbs, structural elements of buildings and chimneys, scatter and refract sunlight, significantly reducing the amount of radiation reaching the surface of the module. The hard shadings located directly on the surface (i.e. bird droppings, leaves, snow) tend to stop sunlight completely. These phenomena significantly affects the output characteristics of photovoltaic modules and often contribute...
-
Model matematyczny strat objętościowych ściskania oleju hydraulicznego w pompie wyporowej o zmiennej wydajności
PublikacjaCelem pracy było stworzenie możliwości oceny strat objętościowych wynikających ze ściskania oleju hydraulicznego w komorach roboczych wysokociśnieniowej pompy wyporowej o zmiennej wydajności na obrót wału. Straty objętościowe ściskania oleju muszą być określone jako funkcje tych samych parametrów, w zależności od których ocenione są straty objętościowe przecieków oleju w komorach, wynikające z jakości rozwiązania konstrukcyjnego...
-
Sposoby przykładania obciążenia zmiennego na konstrukcję płytowo-słupową
PublikacjaW pracy przedstawiono analizę porównawczą wybranych metod zadawania obciążenia zmiennego na konstrukcje płytowo-słupową. Przeanalizowano pięć sposobów rozkładu obciążenia na płytę stropową. Wyniki momentów zginających i przemieszczeń w wybranych punktach dla analizowanych przypadków porównywano z wartościami ekstremalnymi obliczonymi na podstawie powierzchni wpływu (Wariant 1). Wykonane obliczenia pozwoliły na wskazanie zalecanej...
-
MONITORING OF PERMANENT GPS STATIONS AT THE SUDETY MOUNTAINS
PublikacjaThe aim of this paper is to show time-dependent baseline variation between GPS stations situated in South-East Poland. This study was based on daily data analysis of selected GPS stations: WROC, GOPE, MOPI, KRAW and KATO. The start date of the analysis is linked at every station with the beginning of its operation and the closing date of the operation is in 2006. The multiresolution signal decomposition method has been used to...
-
Extending transition curve in analytical design method
PublikacjaThe paper presents the problem of extending the transitional curves, using for this purpose an analytical design method. The basis for the analysis of numerical calculations were carried out for a wide set of parameters characterizing the standard geometric system. We considered an importance of the size of radius of the circular arc and return angle of route on the obtained results after the formulation of appropriate theoretical...
-
Projektowanie układów ramowych z zastosowaniem analizy wrażliwości
PublikacjaW pracy przedstawiono przykład projektowania układów ramowych z zastosowaniem analizy wrażliwości. Rozważane układy ramowe rozwiązano autorskim programem napisanym w środowisku MATLAB, metodą elementów skończonych. Badano wpływ zmiany modułu Younga oraz wpływ zmiany wielkości przekroju poprzecznego na wybrane przemieszczenia ramy. Przedstawiono wyniki dla analizy wrażliwości jedno i wieloparametrycznej.
-
EH36 steel for shipbuilding (plate thicnkness 40 mm) - CMOD - force record, a0/W = 0.5
Dane BadawczeThe basic method of ductility designation of structural steels is the Charpy impact test. The test consists of a single strike of the specimen using a Charpy pendulum. Its result is the value of work necessary to break a specimen at a test temperature. Despite its many advantages, such as its short implementation time and low costs, it has its disadvantages,...
-
EH36 steel for shipbuilding (plate thicnkness 40 mm) - CMOD - force record, a0/W = 0.6
Dane BadawczeThe basic method of ductility designation of structural steels is the Charpy impact test. The test consists of a single strike of the specimen using a Charpy pendulum. Its result is the value of work necessary to break a specimen at a test temperature. Despite its many advantages, such as its short implementation time and low costs, it has its disadvantages,...
-
EH36 steel for shipbuilding (plate thicnkness 30 mm) - CMOD - force record, a0/W = 0.6
Dane BadawczeThe basic method of ductility designation of structural steels is the Charpy impact test. The test consists of a single strike of the specimen using a Charpy pendulum. Its result is the value of work necessary to break a specimen at a test temperature. Despite its many advantages, such as its short implementation time and low costs, it has its disadvantages,...
-
EH36 steel for shipbuilding (plate thicnkness 60 mm) - CMOD - force record, a0/W = 0.6
Dane BadawczeThe basic method of ductility designation of structural steels is the Charpy impact test. The test consists of a single strike of the specimen using a Charpy pendulum. Its result is the value of work necessary to break a specimen at a test temperature. Despite its many advantages, such as its short implementation time and low costs, it has its disadvantages,...
-
EH36 steel for shipbuilding (plate thicnkness 50 mm) - CMOD - force record, a0/W = 0.5
Dane BadawczeThe basic method of ductility designation of structural steels is the Charpy impact test. The test consists of a single strike of the specimen using a Charpy pendulum. Its result is the value of work necessary to break a specimen at a test temperature. Despite its many advantages, such as its short implementation time and low costs, it has its disadvantages,...
-
EH36 steel for shipbuilding (plate thicnkness 50mm) - CMOD - force record, a0/W = 0.6
Dane BadawczeThe basic method of ductility designation of structural steels is the Charpy impact test. The test consists of a single strike of the specimen using a Charpy pendulum. Its result is the value of work necessary to break a specimen at a test temperature. Despite its many advantages, such as its short implementation time and low costs, it has its disadvantages,...
-
EH36 steel for shipbuilding (plate thicnkness 30 mm) - CMOD - force record, a0/W = 0.5
Dane BadawczeThe basic method of ductility designation of structural steels is the Charpy impact test. The test consists of a single strike of the specimen using a Charpy pendulum. Its result is the value of work necessary to break a specimen at a test temperature. Despite its many advantages, such as its short implementation time and low costs, it has its disadvantages,...
-
Characterization of the Functionally Graded Shear Modulus of a Half-Space
PublikacjaIn this article, a method is proposed for determining parameters of the exponentialy varying shear modulus of a functionally graded half-space. The method is based on the analytical solution of the problem of pure shear of an elastic functionally graded half-space by a strip punch. The half-space has the depth-wise exponential variation of its shear modulus, whose parameters are to be determined. The problem is reduced to an integral...
-
Multiparameter sensitivity analysis of a GFRP composite footbridge of a sandwich structure and U-shaped cross-section
PublikacjaThe paper deals with multiparameter sensitivity analysis of a composite footbridge. A shell‐like structure is 14.5 m long shows U‐shaped cross‐section and inner service dimensions 1.3 × 2.5 m. Glass fiber reinforced polymer GFRP laminate constitutes faces of a sandwich structure while PET foam received from recycled bottle builts a core. The structure was divided into 285 independent areas where the thickness of laminates and stiffness...
-
Incorporating installation effects into the probability analysis of controlled modulus columns
PublikacjaThis technical report presents the probabilistic analysis which integrates the Monte Carlo simulation (MCS) with random field theory to model the load–displacement behavior of Controlled Modulus Columns (CMCs) in overconsolidated Poznań clay. Presented study focuses on the practical aspects of statistical analysis of geotechnical data, numerical model development, and results evaluation. Variability and spatial distribution of...
-
On some problems in determining tensile parameters of concrete model from size effect tests
PublikacjaThe paper presents results of numerical simulations of size effect phenomenon in concrete specimens. The behaviour of in-plane geometrically similar notched and unnotched beams under three-point bending is investigated. In total 18 beams are analysed. Concrete beams of four different sizes and five different notch to depth ratios are simulated. Two methods are applied to describe cracks. First, an elasto-plastic constitutive law...
-
Curlicues generated by circle homeomorphisms
PublikacjaWe investigate the curves in the complex plane which are generated by sequences of real numbers being the lifts of the points on the orbit of an orientation preserving circle homeomorphism. Geometrical properties of these curves such as boundedness, superficiality, local discrete radius of curvature are linked with dynamical properties of the circle homeomorphism which generates them: rotation number and its continued fraction...
-
A COMPARISON OF THE WIND SPECTRUM ACCORDING TO DIFFERENT METHODS - AN ORIGINAL PROJECT OF A BUILDING ON A CLIFF IN GDYNIA
PublikacjaThe article presents numerical simulations of the dynamic wind loads on the structure of a building designed on a cliff in Gdynia. The results obtained from the two methods: Davenport’s and Karman’s are compared. The results allowed a comparison of the two methods, and they provided an answer to the question how a construction, designed in such an unusual condition of a cliff behaves under the influence of the gusting wind. The...
-
New Design of Axial Piston Pump with Displaced Swash Plate Axis of Rotation for Hydro-Mechanical Transmissions
PublikacjaThis paper presents a prototype design of an axial piston pump with displaced swash plate axis of rotation in two directions of discharge with electronic control intended for installation on a hydraulic-mechanical gearbox dedicated to working machines. The effect of displacement of the swash plate rotation axis on dead space volume and volumetric efficiency is presented. The construction and principle of operation of the capacity...
-
Alkanethiolates of Group 1,2, and 13-15 Metals
PublikacjaThis manuscript is an update to the earlier Science of Synthesis contribution describing methods for the synthesis of alkanethiolates of group 1, 2, and 13-15 metals. Alkanethiolates can be converted into S-alkyl thiocarboxylic acid esters, 1-thioglycosides, S-alkyl thiosulfinates, tetrahydro-1,4-thiazine-3-ones, sulfides, disulfides, sulfonium salts, dithioacetals and dithioketals, etc. These transformations are accomplished by...
-
Comparative model tests of SDP and CFA pile groups in non-cohesive soil
PublikacjaThe research topic relates to the subject of deep foundations supported on continuous flight auger (CFA) piles and screw displacement piles (SDP). The authors have decided to conduct model tests of foundations supported on the group of piles mentioned above and also the tests of the same piles working alone. The tests are ongoing in Geotechnical Laboratory of Gdańsk University of Technology. The description of test procedure, interpretation...
-
Behaviour of deformed steel columns exposed to impact load during earthquakes - experimental study
PublikacjaIt has been observed during major earthquakes that the so called soft-storey failure of an upper floor of a structure results in large impact load acting on structural members of the lower storeys. It may further lead to progressive collapse of the whole structure substantially intensifying human and material losses. The aim of this paper is to investigate experimentally the behaviour of horizontally deformed columns (deformation...
-
Nondestructive Testing of the Miter Gates Using Various Measurement Methods
PublikacjaWhen any problems related to civil engineering structures appear, identifying the issue through the usage of only one measuring method is difficult. Therefore, comprehensive tests are required to identify the main source. The strains and displacement measurements, as well as modal identification, are widely used in the nondestructive testing of structures. However, measurements are usually carried out at several points and confirm...
-
Changes of Conformation in Albumin with Temperature by Molecular Dynamics Simulations
PublikacjaThis work presents the analysis of the conformation of albumin in the temperature range of 300K – 312K, i.e., in the physiological range. Using molecular dynamics simulations, we calculate values of the backbone and dihedral angles for this molecule. We analyze the global dynamic properties of albumin treated as a chain. In this range of temperature, we study parameters of the molecule and the conformational entropy derived from...
-
Arch bridges under test loadings
PublikacjaThis paper illustrates experience in arch bridges test loadings of the research team of Department of Structural Mechanics and Bridge Structures from the Gdansk University of Technology. The presented calculations results constist the analysis of spatial construction schemes made using the finite elements method (FEM) and its comparison to the field studies. Arch bridges with the longest spans, visualisation of the computational...
-
Firing map for periodically and almost-periodically driven integrate-and-fire models: a dynamical systems approach
PublikacjaWe consider the Leaky Integrate-and-Fire and Perfect Integrator models of neuron’s dynamics with the input function being periodic and almost-periodic (in the sense of Stepanov). In particular we analyze properties and dynamics of the so-called firing map, which iterations give timings of consecutive spikes of a neuron. In case of a periodic input function we provide a detailed description of the sequence of interspike-intervals,...
-
Application of gas chromatography to the study of the kinetics of reactionsin solution. Ring opening reactions for á-lactams studied using internal standard
PublikacjaW pracy przedstawiono metodę badania kinetyki reakcji otwarcia pierścienia á-laktamu, wykorzystującą technikę chromatografii gazowej. Na podstawie badań kinetyki reakcji w różnych temperaturach wyznaczono wartości energii aktywacji dwóch badanych reakcji. Podstawowym celem pracy było pokazanie możliwości wykorzystania GC w badaniach kinetyki reakcji prowadzonych w mikroskali.
-
Quality of analytical results
PublikacjaW pracy przedstawiono podstawowe informacje dotyczące kontroli i zapewnienia jakości wyników analitycznych (QC/QA). W postaci odpowiednich schematów zaprezentowano: ideę spójności pomiarowej; zasady walidacji metodyk analitycznych; rolę materiałów odniesienia w procesie analitycznym.
-
Continuum models for pantographic blocks with second gradient energies which are incomplete
PublikacjaWe postulate a deformation energy for describing the mechanical behavior of so called pantographic blocks, that is bodies constituted by stacking of layers of pantographic sheets. We remark that the pantographic effect is limited in the plane of pantographic sheets and therefore only the second derivatives of transverse displacements along the pantographic fibers appear in the chosen deformation energy. We use this novel energy...
-
Equivalent 4-node enhanced assumed strain and hybrid stress shell elements in 6-parameter theory
PublikacjaWe discuss the equivalence of semi-enhanced assumed strain (EAS) and semi-hybrid stress (SEM) shell finite elements. We use the general nonlinear 6-field shell theory with kinematics composed of generalized displacements composed of the translation field and the rotation field. Due to the presence of rotation tensor the elements have naturally six nodal engineering degrees of freedom. We propose interpolation for a strain field...
-
On Anti-Plane Surface Waves Considering Highly Anisotropic Surface Elasticity Constitutive Relations
PublikacjaWithin the framework of highly anisotropic surface elasticity model we discuss the propagation of new type of surface waves that are anti-plane surface waves. By the highly anisotropic surface elasticity model we mean the model with a surface strain energy density which depends on incomplete set of second derivatives of displacements. From the physical point of view this model corresponds to a coating made of a family of parallel...
-
A Nonlinear Model of a Mesh Shell
PublikacjaFor a certain class of elastic lattice shells experiencing finite deformations, a continual model using the equations of the so-called six-parameter shell theory has been proposed. Within this model, the kinematics of the shell is described using six kinematically independent scalar degrees of freedom — the field of displacements and turns, as in the case of the Cosserat continuum, which gives reason to call the model under consideration...
-
Loudness Scaling Test Based on Categorical Perception
PublikacjaThe main goal of this research study is focused on creating a method for loudness scaling based on categorical perception. Its main features, such as: way of testing, calibration procedure for securing reliable results, employing natural test stimuli, etc., are described in the paper and assessed against a procedure that uses 1/2-octave bands of noise (LGOB) for the loudness growth estimation. The Mann-Whitney U-test is employed...
-
Wave propagation signals in concrete beams under 3-point bending
Dane BadawczeThe DataSet contains the results of the mechanical behaviour of a concrete beams with dimensions 40 x 40 x 160 cm3under the 3-point bending. The beams were made of concrete with the following ingredients: CEM I 42.5R (450 kg/m3), water (177 kg/m3), sand 0-2 (675 kg/m3) and gravel 2-8 (675 kg/m3). The bending test was performed using a Zwick/Roell Z10...
-
Small rov to detection and identification of dangerous underwater objects
PublikacjaA small unmanned underwater vehicle (UUV) to inspection of an undersea space is presented in the paper. Its behavior is controlled by a trained pilot. Correct detection and identification of targets depends on vehicle'sprecise displacement along a predefined route. Nowadays, the UUVs are equipped with an automatic control system to execute some basic maneuvers without constant human interventions. Hence, in the paper, an autopilot...
-
Numerical FDM modelling of wave propagation in concrete structure
PublikacjaThe article presents application of finite difference method to damage detection and its size evaluation in concrete structure by elastic wave propagation method. The simulations of wave propagation in concrete structure were performed for six different damage scenarios. Damages were modelled as areas with changed material properties. Investigation focused on the influence of damage size on the energy of wave reflection. Presented...
-
Reduction of Derivative pipeline effort in water turbine
PublikacjaThe paper presents an approach to evaluate and reduce the effort of the derivative pipeline in a water turbine of a hydrostatic power station in its vulnerable spots. Potential places of the biggest effort of the structure, as well as the coefficient of displacement and safety factor related to them were identified using FEM numerical method. Pipeline reinforcement was designed and made based on FEM analysis. Original technology...
-
In-plane shear nonlinearity in failure behavior of angle-ply laminated shells
PublikacjaThe paper concerns the progressive failure analysis of laminates with the in-plane shear nonlinearity accounted for.The nonlinear shear response of the layer is described by the constitutive relation treating the stresses as a function of strains. Thus it can be easily incorporated into the displacement-based FEM codes. The brittle failure mechanisms of the fibers and the matrix of the layer are recognized with the use of the Hashin...
-
Praktyczne zastosowania analizy wrażliwości na przykładzie projektowania tarczy
PublikacjaW pracy przedstawiono przykłady zastosowania analizy wrażliwości przy projektowaniu tar-czy. Badano wpływ zmian grubości obszarów tarczy – zmiennej projektowej – na przemiesz-czenie wybranego punktu tarczy – zmiennej stanu. Zaproponowano metodę projektowania polegającą na zwiększeniu grubości obszarów tarczy, których wpływ na wariację zmiennej stanu (wrażliwość) jest największa. Do obliczeń numerycznych korzystano z metody elemen-tów...
-
Jacek Namieśnik prof. dr hab. inż.
OsobyUrodził się 10 grudnia 1949 r. w Mogilnie, zmarł 14 kwietnia 2019 r. w Gdańsku – polski chemik, profesor nauk chemicznych, specjalizujący się w chemii analitycznej i środowiskowej. Rektor Politechniki Gdańskiej w latach 2016–2019. Studia wyższe ukończył w 1972 r. na Wydziale Chemicznym Politechniki Gdańskiej, uzyskując tytuł magistra inżyniera chemika. W 1972 r. rozpoczął pracę na Politechnice Gdańskiej, gdzie w 1978 r. obronił...
-
Extended duration running and impulse loading characteristics of an acoustic bearing with enhanced geometry
PublikacjaThis paper presents performance during prolonged running of the acoustic bearing when PZTs are switched off and when they are switched on. The effect of active PZT on shaft’s displacements in X and Y directions is clearly demonstrated. Performance of the acoustic bearing was also assessed when an impulse force was applied to the running shaft at speed. Once again the benefits of having PZTs active are beyond doubt. The instability...
-
Mechanical compatibility of implants used in hernia repair with abdominal wall
PublikacjaThe paper deals with a membrane model of a synthetic surgical mesh for treatment of abdominal hernia. The authors analyse the compatibility of two implant types with the human wall: Dualmesh Gore and Proceed. The finite element method is applied to simulate tjhe behavior of the proposed model. Due fact that recurrences are usually caused by connection failure, this study is focused on reaction forces in supports representing the...
-
On the Equations of the Surface Elasticity Model Based on the Theory of Polymeric Brushes
PublikacjaMotivating by theory of polymers, in particular, by the models of polymeric brushes we present here the homogenized (continual) two-dimensional (2D) model of surface elasticity. A polymeric brush consists of an system of almost aligned rigid polymeric chains. The interaction between chain links are described through Stockmayer potential, which take into account also dipole-dipole interactions. The presented 2D model can be treated...
-
Green strength (buildability performance) of concretes containing magnetite aggregate (M0-M100) mixes
Dane BadawczeRaw data for determination of buildability (green strength) properties of concrete mixes determined by squeezing test using QuantumX MX840B with CATMAN-EASY software, determined after 15, 30, 45 and 60 minutes. Values present force and two displacement measurements by LVDT.Additionally, an Origin (*.opju) file with processed data presenting stress-strain...
-
COMMENTS ON EXISTING ANALYTICAL SOLUTIONS TO THE WAVE-INDUCED CYCLIC RESPONSE OF A POROUS SEABED OF INFINITE THICKNESS
PublikacjaThis paper deals with the wave-induced cyclic response of a porous seabed (by means of oscillating parameters: pore-fluid pressure, soil displacement components, effective normal stress and shear stress components) due to a surface sinusoidal water-wave propagating over a seabed of infinite thickness. The main existing analytical solutions to the governing problem are critically discussed, pointing out their meaningful errors and...
-
Investigation of behaviour of metal structures with polymer dampers under dynamic loads
PublikacjaA large number of accidents concerning structures subjected to dynamic loads have been recently observed. One of the examples of such a structure is a temporary steel grandstand erected using scaffolding system. Dynamic load that is generated by crowd movement has a significant influence on the behaviour of the structure and may lead to excessive structural vibrations. The aim of the study is to consider the idea of using polymer...
-
Wiktoria Wojnicz dr hab. inż.
OsobyDSc in Mechanics (in the field of Biomechanics) - Lodz Univeristy of Technology, 2019 PhD in Mechanics (in the field of Biomechanics) - Lodz Univeristy of Technology, 2009 (with distinction) Publikacje z listy MNiSW (2009 - ) Wojnicz W., Wittbrodt E., Analysis of muscles' behaviour. Part I. The computational model of muscle. Acta of Bioengineering and Biomechanics, Vol. 11, No.4, 2009, p. 15-21 Wojnicz W., Wittbrodt E., Analysis...
-
Optimum number of actuators to minimize the cross-sectional area of prestressable cable and truss structures
PublikacjaThis paper describes a new computational method for determining the optimum number of actuators to design the optimal and economic cross-sectional area of pin-jointed assemblies based on the conventional force method. The most active members are selected to be prestressed to redistribute stress in the whole structure, resulting in regulating the internal force of bars that face high stress. Reducing stress in critical members allows...
-
Optimum shapes and dimensions of rubber bumpers in order to reduce structural pounding during seismic excitations
PublikacjaLarge displacement of structures observed during seismic excitations may lead to collisions between two adjacent, insufficiently-separated buildings and may result in major damages of both of them. In many building codes, appropriate equations or approximately recommended distances between structures in order to avoid pounding hazard have been introduced. Unfortunately, further, more detailed considerations show that safety situation...