Filtry
wszystkich: 3663
-
Katalog
- Publikacje 2633 wyników po odfiltrowaniu
- Czasopisma 34 wyników po odfiltrowaniu
- Konferencje 5 wyników po odfiltrowaniu
- Osoby 67 wyników po odfiltrowaniu
- Projekty 9 wyników po odfiltrowaniu
- Zespoły Badawcze 1 wyników po odfiltrowaniu
- Kursy Online 86 wyników po odfiltrowaniu
- Wydarzenia 10 wyników po odfiltrowaniu
- Dane Badawcze 818 wyników po odfiltrowaniu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: SECRET SHARING
-
Method for improving multibeam sonar bearing accuracy
PublikacjaPrzedstawiono prostą metodę poprawy dokładności namiarów w sonarach wielowiązkowych. Zasada zaproponowanej metoda jest zbliżona do metody monopulsowej stosowanej powszechnie w radarach i sonarach. Nie wymaga jednak ręcznego lub automatycznego obracania wiązek, co wydatnie zmniejsza potrzebne nakłady obliczeniowe procesorów sonaru Stosowanie metody daje znaczne zmniejszenie błędów namiarów przy względnie dużym wyjściowym stosunku...
-
Biocompatibility and bioactivity of bearing loaded metallic implants
PublikacjaPresentation of developed titanium alloy base composite materials possessing better biocompatibility, longer lifetime and bioactivity behavior for bearing loaded implants, e.g. hip joint and knee joint endoproshtesis.
-
Calcium sulphate scaling in membrane distillation process
Publikacja -
Modeling of acoustics of hearing aid earmold systems
Publikacja -
Waveguide modeling as a tool for fitting a hearing aid
Publikacja -
Economic benefits of dynamic charging of electric buses
PublikacjaDiesel engines buses are still the most used type of buses. Electric buses provide promising green alternatives and a lot of advantages, but their main disadvantages are limited travel range and long charging time. This article is a presentation of innovative solution for charging of electric busses - Dynamic Charging (IMC). The modern IMC system in Solingen was presented. At the end of the article, a proposal was made to introduce...
-
Poroelastic Material for Urban Roads Wearing Courses
PublikacjaConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
BEARING SYSTEMS OF WIND TURBINES – MAINTENANCE PROBLEMS
PublikacjaW praktyce eksploatacyjnej turbin wiatrowych o tradycyjnej konstrukcji (przekładniowych) obserwowana jest duża awaryjność przekładni, a zwłaszcza łożysk tocznych szybkoobrotowych wałów przekładni. W Polsce na zlecenie właściciela dużej farmy wiatrowej, firmy Energa Wytwarzanie S.A., Politechnika Gdańska we współpracy z Politechniką Poznańską i Akademią Górniczo Hutniczą podjęły badania mające na celu diagnozowanie przyczyn uszkodzeń...
-
HYDROSTATIC THRUST BEARING WITH REDUCED POWER LOSSES
PublikacjaIn many cases in rotating machinery, axial load is carried by tilting pad thrust bearings which have been developed since the beginning of 20th century. For high reliability and simplicity, most commonly the bearings are bath lubricated. In the times of sustainable development, however, minimization of friction losses becomes an important criterion for machinery assessment, and a strategic goal of their development. Performed calculations,...
-
Poroelastic Material for Urban Roads Wearing Courses
PublikacjaConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
Digital hearing aid with time and spectral transposition.
PublikacjaNastępstwem uruchomienia w Polsce, prowadzonych na szeroką skalę, badań przesiewowych słuchu jest konieczność zaoferowania pomocy osobom cierpiącym na niedosłuch poprzez leczenie i protetykę słuchu. Tymczasem, aktualnie oferowane rozwiązania aparatów słuchowych nie są w stanie sprostać niektórym specjalistycznym potrzebom aparatowania, m. in.: najmłodszych dzieci, osób pracujących w hałasie, pilotów wojskowych oraz osób korzystających...
-
Waveguide model of the hearing aid earmold system
PublikacjaBackground The earmold system of the Behind-The-Ear hearing aid is an acoustic system that modifies the spectrum of the propagated sound waves. Improper selection of the earmold system may result in deterioration of sound quality and speech intelligibility. Computer modeling methods may be useful in the process of hearing aid fitting, allowing physician to examine various earmold system configurations and choose the optimum one...
-
Waveguide model of the hearing aid earmold system
PublikacjaBackground The earmold system of the Behind-The-Ear hearing aid is an acoustic system that modifies the spectrum of the propagated sound waves. Improper selection of the earmold system may result in deterioration of sound quality and speech intelligibility. Computer modeling methods may be useful in the process of hearing aid fitting, allowing physician to examine various earmold system configurations and choose the optimum one...
-
Hearing aid operating in acoustical free field
PublikacjaAparatowanie bardzo małych dzieci (od 5 miesiąca życia) za pomocą standardowych protez słuchu natrafia na wiele trudności natury praktycznej. Dotyczy to procesu dopasowania aparatu słuchowego, czyli doboru jego ustawień stosownie do aktualnych charakterystyk ubytku słuchu dzieci. Tymczasem wczesne aparatowanie jest zagadnieniem o ogromnym zanczeniu dla rozwoju słuchu, mowy i ogólnej inteligencji dziecka. Referat prezentuje uzyskane...
-
INFLUENCE OF TIME ON THE BEARING CAPACITY OF PRECAST PILES
PublikacjaOne of the most popular types of foundations in layered subsoil with very differentiated soil shear strengths are precast piles. One of the reasons is a fact that we can well control the driving process during the installation of these piles. The principles of the assessment of bearing capacity and settlements of the piles given by Eurocode 7, concentrate on two main methods, i.e. Static Pile Load Tests (SPLT) and Dynamic Driving...
-
Speech recognition system for hearing impaired people.
PublikacjaPraca przedstawia wyniki badań z zakresu rozpoznawania mowy. Tworzony system wykorzystujący dane wizualne i akustyczne będzie ułatwiał trening poprawnego mówienia dla osób po operacji transplantacji ślimaka i innych osób wykazujących poważne uszkodzenia słuchu. Active Shape models zostały wykorzystane do wyznaczania parametrów wizualnych na podstawie analizy kształtu i ruchu ust w nagraniach wideo. Parametry akustyczne bazują na...
-
Internet-based automatic hearing assessment system
PublikacjaCelem referatu jest prezentacja systemu przesiewowego badania słuchu w oparciu o Internet. Wady słuchu stanowią jedną z najszybciej postępujących chorób we współczesnym społeczeństwie. W tym kontekście ważne staje się umożliwienie przeprowadzania masowych testów wykrywających ubytki słuchu. Przedstawiona aplikacja zawiera audiometryczny test tonalny, test ilustrowany dla dzieci oraz test rozumienia mowy w szumie. Po zakończeniu...
-
Hydrogen charging of nitrided steel in acid solution
PublikacjaKonstrukcyjną stal, azotowaną w wyładowaniu jarzeniowym w mieszaninie gazów o różnej zawartości N2, H2 i Ar, poddawano katodowemu nawodorowaniu w kwaśnym roztworze, imitującym przepracowany olej maszynowy. W pomiarach szybkości przenikania wodoru i ekstrakcji próżniowej określano wpływ azotowanych warstw, odpowiednio, na transport wodoru i na jego nieodwracalne pułapkowanie. W obecności niezdefektowanej warstwy kompaktowych azotków...
-
Bearing testing machine with rotating load vector.
PublikacjaW pracy przedstawiono koncepcję konstrukcyjną i prototyp stanowiska badawczego z wirująca reakcją łożyskową przeznaczonego do testowania wytrzymałości zmęczeniowej warstw ślizgowych w łożyskach poprzecznych. Konstrukcja i przeznaczenie maszyny zbudowanej w laboratorium tribologicznym Politechniki Gdańskiej jest zgodna z zaleceniami normy ISO 7905. Przeanalizowano zalety i wady maszyny badawczej o takim wzorcu obciążenia testującego.
-
Bearing capacity of the working platform with kinematic method
PublikacjaBearing capacity of the working platform for heavy tracks was analysed using Distinct Layout Optimization (DLO) method. The platform layer constructed from cohesionless soils is resting on weak cohesive subgrade. Different thickness of the platform, its effective angle of internal friction and undrained shear strength of the soft soil were taken into consideration. Kinematic method permits different failure mechanisms to be analyzed....
-
Acoustic journal bearing - A search for adequate configuration
PublikacjaClassical non-contact bearings are already used in a number of specialist applications but there are somespecialist areas where they cannot be used for variety of reasons and acoustic sliding bearings could be an alternative. The paper presents the quest for a configuration of an acoustic journal bearing and shows that the overall shape of the bearing and its geometry are of a vital importance for the load capacity oft he bearing....
-
Loudness Scaling Test Based on Categorical Perception
PublikacjaThe main goal of this research study is focused on creating a method for loudness scaling based on categorical perception. Its main features, such as: way of testing, calibration procedure for securing reliable results, employing natural test stimuli, etc., are described in the paper and assessed against a procedure that uses 1/2-octave bands of noise (LGOB) for the loudness growth estimation. The Mann-Whitney U-test is employed...
-
Storing Matter’technique in SIMS depth profile analysis
PublikacjaSecondary ion mass spectrometry (SIMS) is a very useful technique for the analysis of layered systems. It is based on the primary ion beam sputtering of solids and mass analysis of the emitted secondary ions. A main limitation of this technique results from the direct quantitative analysis, since the ionization efficiency of a given atom is highly influenced by the neighbouring atoms at the surface. This phenomenon is known as...
-
Mathemathical model of radial passive magnetic bearing
PublikacjaIn the article mathematical radial model of passive magnetic bearings to ocean engineering units has been presented. The units application in underwater thrusters should increase propulsion systems durability and gives lower maintenance costs. The rotor of electric motor is hanging in magnetic field taken from radial passive magnetic bearings. However axial direction maintenance must be controlled with electromagnets and their...
-
Biocompatibility and bioactivity of load-bearing metallic implants
PublikacjaThe main objective of here presented research is to develop the titanium (Ti) alloy base composite materials possessing better biocompatibility, longer lifetime and bioactivity behaviour for load-bearing implants, e.g. hip joint and knee joint endoprosthesis. The development of such materials is performed through: modeling the material behaviour in biological environment in long time and developing of new procedures for such evaluation;...
-
Biocompatibility and Bioactivity of Load-Bearing Metallic Implants
PublikacjaThe main objective of here presented research is to develop the titanium (Ti) alloy base composite materials possessing better biocompatibility, longer lifetime and bioactivity behaviour for load-bearing implants, e.g. hip joint and knee joint endoprosthesis. The development of such materials is performed through: modeling the material behaviour in biological environment in long time and developing of new procedures for such evaluation;...
-
Expert media approach to hearing aids fitting
PublikacjaW artykule zaprezentowano problematykę dopasowania protez słuchu. Przedstawiono system ekspercki, który pozwala na znalezienie charakterystyk aparatu słuchowego adekwatnego do uszkodzenia słuchu. System został oparty o metodę zbiorów przybliżonych i logikę rozmytą.
-
Showing compliance of probabilistic assessments with safety goals
PublikacjaW niektórych standardach formułuje się wymagania, że wyniki modelowania probabilistycznego i oszacowań ryzyka powinny zawierać ocenę niepewności. Modelowanie złożonych systemów bazuje w praktyce na kategoriach zdarzeń, które są mniej lub więcej rozmyte. Artykuł dotyczy kwestii wykazywania zgodności wyników modelowania probabilistycznego z ilościowymi kryteriami bezpieczeństwa. Proponuje się metodę definiowania takich kryteriów...
-
Photophysics and Halide Quenching of Soret-excited ZnTPPS4- in Aqueous Media
PublikacjaSteady state S2-S0 and S1-S0 absorption and emission spectra and picosecond S2 decay and S1 fluorescence rise times have been measured for the model porphyrin ZnTPPS4− in water and in aqueous iodide solutions of constant ionic strength. The dynamics of S1 quenching by iodide are well-modeled by a Stern-Volmer mechanism yielding kQ = 1.75 × 109 M−1 s−1. The S2 state is quenched on a ps time scale by a static electron-transfer mechanism...
-
Results of the “DPDT-Auger” Research Project on Screw Displacement Piles
PublikacjaThe main objective of the “DPDT-Auger” research project was to test the prototype DPDT auger for forming screw displacement piles in the ground (patented in Poland in 2020). An additional aim was to develop design methods and rules for the making of such piles. The augers and piles were first tested on a model scale, and then more extensively in the real scale on experimental field plots. The results found the overall functionality...
-
The analysis of soil resistance during screw displacement pile installation
PublikacjaThe analysis of soil resistances during screw displacement pile installation based on model and field tests. The investigations were carried out as a part of research project, financed by the Polish Ministry of Science and Higher Education. A proposal of empirical method for prediction of rotation resistance (torque) during screw auger penetration in non-cohesive subsoil based on CPT result.
-
Detremination of the cutting power of the sawing process using both preliminary sawing data and modern fracture mechanics
PublikacjaPrzedstawiono medodykę prognozowania mocy skrawania dla procesu piłowania drewna cienkimi piłami. Przewidywanie zapotrzebowania mocy skrawania oparte jest na współczesnej mechanice pękania, a do wyznaczenia stałych materiałowych: wiązkości materiału oraz niszczących napężeń ścinających wykorzystano wyniki wstępnych badań eksperymentalnych. Błędy prognozowania nie przekraczają 15.5% dla przypadku cienkich pił gdy rolę znacząca odgrywają...
-
Thickness accuracy of sash gang sawing
PublikacjaThin lamellae, corresponding to the layer components of structural glued members, i.e. 2-ply or 3-ply glued parquet, can be manufactured in re-sawing operations of kiln-dried wood blocks. These must be prepared with high dimensional accuracy and adequate surface quality following specific technical requirements for lamellae thickness variations, especially in the upper layers of the glued composite parquet. The accuracy of oak...
-
Fast Approximate String Search for Wikification
PublikacjaThe paper presents a novel method for fast approximate string search based on neural distance metrics embeddings. Our research is focused primarily on applying the proposed method for entity retrieval in the Wikification process, which is similar to edit distance-based similarity search on the typical dictionary. The proposed method has been compared with symmetric delete spelling correction algorithm and proven to be more efficient...
-
The Zręb Tower proposals for saving the ruins
PublikacjaZabytkowa baszta pod Zrębem w latach siedemdziesiątych XX wieku uległa awarii, zawalił się dach oraz częściowo ściany. W pracy przedstawiono propozycje zabezpieczenia budowli przed postępującą destrukcją.
-
The reduction of vibrations in circular sawing machines
PublikacjaThe presented in this paper the main objectives of the research were to explore vibrations signals of the main spindle system, the machine tool body and a circular saw to extract informative features for assessment of the designs of the panel saw Fx3 and its follower Fx550.Even though the main spindle of the new table sliding saw Fx550 has its rotational speeds larger about 20% in comparison to the Fx3, peak values of the vibrational...
-
Identification of Secreted Exoproteome Fingerprints of Highly-Virulent and Non-Virulent Staphylococcus aureus Strains
Publikacja -
Postscripts: The Journal of Sacred Texts and Contemporary Worlds
Czasopisma -
International Journal of Internet Technology and Secured Transactions
Czasopisma -
Knowledge sharing and knowledge hiding in light of the mistakes acceptance component of learning culture- knowledge culture and human capital implications
PublikacjaPurpose: This study examines the micromechanisms of how knowledge culture fosters human capital development. Method: An empirical model was developed using the structural equation modeling method (SEM) based on a sample of 321 Polish knowledge workers employed in different industries. Findings: This study provides direct empirical evidence that tacit knowledge sharing supports human capital, whereas tacit knowledge hiding does...
-
THE EFFECT OF WOOD DRYING METHOD ON THE GRANULARITY OF SAWDUST OBTAINED DURING THE SAWING PROCESS USING THE FRAME SAWING MACHINE
PublikacjaThe experimental results of the study focused on the effect of drying processes of warm air drying at the temperature of 6580°C and warm air-steam mixture drying at the temperature of 105°C of pine and beech wood to the size of sawdust grains created by cutting using RPW 15M frame saw is presented in the paper. Particle size analysis of dry sawdust was performed using two methods - screening method and optical method based on...
-
Mechanisms shaping the synergism of zeaxanthin and PsbS in photoprotective energy dissipation in the photosynthetic apparatus of plants
Publikacja -
Three Point Bending of Laser Engineered Net Shaping (LENS) Repaired Inconel 625
Publikacja -
Shaping New Generations of Managers and Consumers: CSR Implementation and Higher Education System in Poland
Publikacja -
The influence of methods of potato weed control and meteorological conditions on shaping the tuber yield structure
Publikacja -
Participatory co-design approach for Greencoin educational tool shaping urban green behaviors.
PublikacjaOur main goal is to prepare assumptions of the Greencoin (GC) cybernetic system, implying pro-ecological attitudes and behavior of city residents. We used qualitative methods, including a literature review and action research -workshops attended by academics, representatives of private and business sectors, urban movements, municipal institutions’ partners, and residents. Our results defined functionalities of the GC, identified...
-
Organic solvents aggregating and shaping structural folding of protein, a case study of the protease enzyme
PublikacjaLow solubility of reactants or products in aqueous solutions can result in the enzymatic catalytic reactions that can occur in non-aqueous solutions. In current study we investigated aqueous solutions containing different organic solvents / deep eutectic solvents (DESs) that can influence the protease enzyme's activity, structural, and thermal stabilities. Retroviral aspartic protease enzyme is responsible for the cleavage of the...
-
Modified methods of impulse radio spectrum shaping to improve electromagnetic environment in UWB systems
PublikacjaW publikacji zamieszczono opis metod kształtowania widma ultraszerokopasmowego radia impulsowego w zakresie eliminacji niepożądanych składowych widma. Opisano sposób adaptacji tych metod do zwiększenia odporności transmisji ultraszerokopasmowych na zakłócenia wąskopasmowe i przedstawiono wyniki symulacji komputerowych jakości transmisji w łączu UWB.
-
Shaping the new planning curricula in the post-socialistic context lessons from Poland and Russia
PublikacjaPlanning education is the issue widely discussed during various conferences and seminars, especially ones grouping the representatives of universities offering professional education in this field. But to large extend this discourse is dominated by the realities and specifics of the highly- developed countries, which is also reflected in the structure of the organizations of universities offering these. At the same time planning...
-
Shaping New Generations of Managers and Consumers: CSR Implementation and Higher Education System in Poland
PublikacjaConsidering the Corporate Social Responsibility as a significant research and education topic for university staff, students, graduates and the whole society, has become a sign of our times. Universities and other education institutions, including the third sector, play an important role, incorporating CSR as a crosscutting issue, in particular into the curricula of future managers and graduate students, no matter the country we...