Filters
total: 1593
filtered: 1385
displaying 1000 best results Help
Search results for: ENGINE ROTATION SPEED
-
Experimental study on the selected aspects of bow thruster generated flow field at ship zero-speed conditions
PublicationThe paper presents the results of experimental study on the interaction between the bow thrusters understood as the flow field changes generated by bow tunnel thruster in deep water conditions operated as a single and twin units. The research was limited to zero-speed case for the ship dead in the water. The influence of the hull form and jet spread between the neighbouring thrusters for several combinations of the applied bow...
-
Implementation of high-speed data transmission technological demonstrator using software defined radio technology
PublicationIn the article implementation of a high-speed data transmission technological demonstrator using software defined radio technology is presented. A system architecture design including asymmetric framing transmission organization, which differs from the ones used in cellular systems is described. The construction of technological demonstrator consisting of a management unit, radio unit and programmable multi-threaded software performing...
-
Novel adaptive flux observer for wide speed range sensorless control of induction motor
PublicationA new adaptive flux observer of induction motor is presented in the paper. The Lyapunov theory is utilized for derivation of the adaptation law of rotor flux angular speed, which acts as unknown parameter in an augmented induction motor model. In the field weakening region, where stray fluxes are comparable with rotor flux magnitude, the air-gap flux stabilization is proposed. An air-gap flux multiscalar model is derived for stator...
-
Influence of the Tool Rotational Speed on Physical and Chemical Properties of Dissimilar Friction-Stir-Welded AA5083/AA6060 Joints
PublicationAluminum alloys have been successfully used in the railroad and automotive industries because of their potential to significantly reduce component weights, and their good mechanical and anti-corrosion properties. Problems with joining aluminum alloys are characterized by low weldability, which influences the need for studies focused on unconventional methods. The environmentally friendly and low-cost friction-stir-welding method...
-
Analysis of different tillage implements with respect to reduced fuel consumption, tractor operating speed and its wheel slippage
PublicationNowadays the prices of agricultural farm produced products are increasing with ant-speed and the prices of input for raising crops are increasing with rocket-speed. Therefore, there is a dire need to conduct some important studies to innovate the techniques which can lower the costs of crop production. In this context, this study was conducted to evaluate the consumption of fuel at different tillage implements, tractor operating...
-
Stirling engine design effects on performance indicies.
PublicationW pracy przedstawiono analizę wpływu wybranych parametrów konstrukcyjnych silnika Stirlinga MAC-02 na jego własności eksploatacyjne. Przyjmując maksimum mocy jako kryterium optymalizacji badano jaki wpływ na wybrane wskaźniki jakości (moc i sprawność) oraz optymalizowane parametry konstrukcyjne silnika (wymiary wymiennika cieplnego oraz parametry układu korbowego) mają ograniczenia nałożone na ciepło dostarczane oraz długość...
-
Stochastic model of the process of diesel engine operation.
PublicationStreszczenie: Najistotniejszym problemem eksploatacji silników o zapłonie samoczynnym jest problem racjonalnego (a zwłaszcza optymalnego) sterowania procesem eksploatacji tych silników. Sterowanie takie może ułatwić zastosowanie iteracyjnego algorytmu wyznaczania optymalnych strategii opracowanego przez R.A. Howarda. Wykorzystanie jednak tego algorytmu do sterowania procesem eksploatacji silników wymaga między innymi opracowania...
-
Development trends of automotive engine cooling systems
PublicationDzięki daleko idącym modyfikacjom układów zasilania i zapłonu silników samochodowych oraz udoskonaleniom układów oczyszczania spalin uzyskano znaczne zmniejszenie emisji związków toksycznych. Układy chłodzenia z pompą cieczy napędzaną mechanicznie stają się archaiczne nie pozwalając na swobodne sterowanie obiegiem cieczy. Również różna wartość temperatury potrzebnej do schładzania różnych procesów wymaga sterowanych zaworów trójdrożnych...
-
Technical Engine for Democratization of Modeling, Simulations, and Predictions
PublicationComputational science and engineering play a critical role in advancing both research and daily-life challenges across almost every discipline. As a society, we apply search engines, social media, and se- lected aspects of engineering to improve personal and professional growth. Recently, leveraging such aspects as behavioral model analysis, simulation, big data extraction, and human computation is gain- ing momentum. The nexus...
-
Investigation of a Stirling engine as a micro-CHP system
PublicationW pracy przedstawiono przegląd konstrukcji silników Stirlinga, które mogą być stosowane w układach mikro-kogeneracyjnych. Zaprezentowano również wyniki badań silnika Stirlinga przeprowadzonych przy różnych obciążeniach cieplnych i elektrycznych układu.
-
Metrological analysis of an computerized system of protection against electric shock in circuits with variable speed drives
PublicationDrive systems, that can be operated at variable speed, are equipped with power electronics converters. This causes distortion of the earth current, and consequently the need to take into account the use of proper protective devices in relation to earth current harmonics. This paper presents a system for protection against electric shock in circuits with power electronics converters and metrological analysis indicating the requirements...
-
Two approaches to model the behaviour of soft natural clays under principal stress axes rotation.
PublicationPrzedstawiono porównanie dwóch podstawowych metod modelowania konstytutywnego pozwalających na symulację odkształcenia przy obrocie składowych głównych naprężenia. Dotyczy to zastosowania wzmocnienia kinematycznego oraz modelu wielopłaszczyznowego (multi-laminate). Wyniki symulacji porównano z wynikami badań laboratoryjnym w cylindrycznym aparacie skrętnym na próbkach w kształcie wydrążonego walca.
-
Biaxial order and a rotation of the minor director in the nematic phase of an organo-siloxane tetrapode by the electric field
Publication -
CAUSALITY IN MODELS OF THERMAL PROCESSES IN SHIP ENGINE ROOMS WITH THE USE OF BOND GRAPH (BG) METHOD
PublicationWith a single approach to modeling elements of different physical nature, the method of Bond Graph (BG) is particularly well suited for modeling energy systems consisting of mechanical, thermal, electrical and hydraulic elements that operate in the power system engine room. The paper refers to the earlier presented new concept of thermal process modeling using the BG method. The authors own suggestions for determining causality...
-
Adaptive traffic optimization using Variable Speed Limits; Adaptacyjna optymalizacja ruchu drogowego przy pomocy zmiennych ograniczeń prędkości
PublicationVariable speed limits (VSL) is an intelligent transportation system (ITS) solution for traffic management. The speed limits can be changed dynamically in order to adapt to traffic, weather, or road surface conditions. This paper presents an approach for such an adaptive traffic control where the primary goal is to ensure traffic safety and efficiency of the traffic control system (fast response to dynamically changing traffic,...
-
Evaluation of the significance of the effect of the active cross-sectional area of the inlet air channel on the specific enthalpy of the exhaust gas of a diesel engine using statistics F of the Fisher-Snedecor distribution
PublicationThis paper presents the application of Fisher-Snedecor distribution F statistics to assess the significance of the influence of changes in the active cross-sectional area of the inlet air channel (Adol) flow in a diesel engine on the observed diagnostic parameter determined on the basis of measurements of the quick changing exhaust gas temperature in the outlet channel, which is the specific enthalpy of the exhaust gas stream within...
-
Effect of pine impregnation and feed speed on sound level and cutting power in wood sawing
PublicationThe sound levels along with the cutting power registered during the sawing process of the impregnated and non-impregnated pine wood at two feed speeds are shown and compared in this paper. Statistically significant differences in the acoustic signals occurred at the lower feed rate. The differences became smaller with an increase in the feed speed. In contrast to the sound signal, the differences...
-
Optimization of the spindle speed during milling of large-sized structures with the use of technique of Experiment-Aided Virtual Prototyping
PublicationIn the paper are presented considerations concerning vibration suppression problems during milling of large-sized workpieces with the use of innovative method of matching the spindle speed of cutting tool. It depends on repeatable change of the spindle speed value as soon as the optimal vibration state of the workpiece approaches. The values of dominant “peaks” in the frequency spectra and the Root Mean Square (RMS) values of time...
-
High-speed memoryless binary/residue converter
PublicationW pracy zaprezentowano nowy szybki konwerter z systemu binarnego do systemu resztowego dla liczb o zakresie do 60 bitów. W konwerterze stosowane są wyłącznie układy kombinacyjne. Algorytm konwertera oparty jest na dodawaniu niezerowych cyfr binarnych reprezentacji kolejnych potęg 2 modulo m. Dodawanie jest realizowane przy użyciu wielooperandowego sumatora CSA oraz sumatora CPA. Suma wyjściowa CPA jest redukowana do zakresu 2m-1...
-
Changes in the speed of ants as a result of aggressive interactions
Publication -
Digital structures for high-speed signal processing
PublicationThe work covers several issues of realization of digital structures for pipelined processing of real and complex signals with the use of binary arithmetic and residue arithmetic. Basic rules of performing operations in residue arithmetic are presented along with selected residue number systems for processing of complex signals and computation of convolution. Subsequently, methods of conversion of numbers from weighted systems to...
-
Frequency characteristics of induction machine speed observers
PublicationWłaściwości napędu bezczujnikowego z silnikiem indukcyjnym zależą od struktury obserwatora prędkości. System ten wymaga starannej analizy w przypadku uszkodzenia maszyny, której celem jest odpowiedź na pytania: jak układ regulacji pracuje przy niesymetrii maszyny spowodowanej np. uszkodzeniem klatki wirnika oraz jak obserwator odtwarza pulsacje prędkości spowodowane niesymetrią maszyny. W artykule przedstawiono charakterystyki...
-
Assessment of the Speed Management Impact on Road Traffic Safety on the Sections of Motorways and Expressways Using Simulation Methods
PublicationMethods used to evaluate the impact of Intelligent Transport System (ITS) services on road safety are usually based on expert assessments or statistical studies. However, commonly used methods are challenging to apply in the planning process of ITS services. This paper presents the methodology of research using surrogate safety measures calculated and calibrated with the use of simulation techniques and a driving simulator. This...
-
MRAS-Based Switching Linear Feedback Strategy for Sensorless Speed Control of Induction Motor Drives
PublicationThis paper presents a newly designed switching linear feedback structure of sliding mode control (SLF-SMC) plugged with an model reference adaptive system (MRAS) based sensorless fieldoriented control (SFOC) for induction motor (IM). Indeed, the performance of the MRAS depends mainly on the operating point and the parametric variation of the IM. Hence, the sliding mode control (SMC) could be considered a good control alternative...
-
A comparative study of pentanol (C5 alcohol) and kerosene blends in terms of gas turbine engine performance and exhaust gas emission
PublicationThe growing demand for sustainable and clean energy sources provides the incentive for the development of alternative fuels. Simultaneously, the development of gas turbine technologies with flexible fuel supply systems enables the use of alternative non-fossil fuels that can play key roles in contributing to global efforts in meeting emissions targets. This paper presents the current state of knowledge on the production and potential...
-
Application of the F-statistic of the Fisher-Snedecor distribution to analyze the significance of the effect of changes in the compression ratio of a diesel engine on the value of the specific enthalpy of the exhaust gas flow
PublicationThe paper discusses the impact of changes in the compression ratio on the operating parameters of a diesel engine, e.g. on the temperature of exhaust gases. It presents the construction of the laboratory test stand, on which experimental measurements were realized. It is characterized how the actual changes of the compression ratio were introduced to the existing engine. The program of experimental investigations taking into account...
-
The Development of a Combined Method to Quickly Assess Ship Speed and Fuel Consumption at Different Powertrain Load and Sea Conditions
PublicationDecision support systems (DSS) recently have been increasingly in use during ships operation. They require realistic input data regarding different aspects of navigation. To address the optimal weather routing of a ship, which is one of the most promising field of DSS application, it is necessary to accurately predict an actually attainable speed of a ship and corresponding fuel consumption at given loading conditions and predicted...
-
Augmented speed control scheme of dual induction motors with mutual flux angle control loop
PublicationThis paper proposes an augmented speed control scheme of dual induction motors fed by a five-leg voltage source inverter (VSI) with a common/shared-leg. An additional control loop is proposed here and based on the mutual flux angle – the difference between flux angular positions of the IMs. The main purpose of this research is to minimize the energy losses in the common inverter leg by controlling the mutual flux angle, at equal...
-
Study of prototype multi-pole non-salient field winding for high speed brushless synchronous generator
PublicationIn this paper a non-salient field winding for a brushless synchronous generator working with high speed in an autonomous energy generation system (e.g. airplane power grid) has been presented. A conception of a six-pole cylindrical-rotor with distributed field winding has been proposed. Comparison study of salient and prototype non-salient field winding has been carried out. Chosen simulation and measurement results of the generator...
-
Tilting pad thrust bearing with novel material selection - experimental comparison of low and medium speed operation
PublicationThe advances in material engineering led to the development of hard carbon based coatings applied in numerous applications in order to prevent or minimize wear of the parts in contact. With Triondur® coatings, the bearing company Schaeffler has succeeded in halving the friction losses in the valve trains of passenger cars. The coatings are optimized for high abrasive wear protection and low sliding friction moments. Altogether...
-
A model of fuel combustion process in the marine reciprocating engine work space taking into account load and wear of crankshaft-piston assembly and the theory of semi-Markov processes
PublicationThe ar ticle analyses the operation of reciprocal internal combu stion engines, with mar ine engines u sed a s an example. The analysis takes into account types of energy conversion in the work spaces (cylinders) of these engines, loads of their crankshaft-piston assemblies, and types of fuel combustion which can take place in these spaces during engine operation. It is highlighted that the analysed time-dependent loads of marine...
-
Modeling the impact of discretizing rotor angular position on computation of field-oriented current components in high speed electric drives
PublicationModern drives consist of alternating current electric motors, and the field-oriented control (FOC) of such motors enables fast, precise, and robust regulation of a drive's mechanical variables such as torque, speed, and position. The control algorithm, implemented in a microprocessor, requires feedback from motor currents, and the quality of this feedback is essential to a drive's control properties. Motor phase currents are sampled...
-
Ground tire rubber thermo-mechanically devulcanized in the presence of waste engine oil as asphalt modifier
PublicationCross-linked elastomers network is main limitation for industrial usage of ground tire rubber (GTR) as asphalts’ and road pavements modifier. GTR was thermo-mechanically devulcanized via extrusion in the presence of waste engine oil (WEO) at temperature ranges from 150 to 280 °C. Combined impact of WEO content and extruder barrel temperature on the change of cross-linked structure of degraded GTR (DTGR) was investigated through...
-
Multiparameter analysis of Stirling engine with Ericsson drive mechanism.
PublicationW pracy zaprezentowano wyniki optymalizacji parametrów konstrukcyjnych silnika Stirlinga o konfiguracji beta z mechanizmem korbowym Ericssona. Jako kryterium przyjęto maksymalizację mocy silnika. W pierwszym etapie poddano optymalizacji tylko parametry konstrukcyjne wymiennika ciepła (7 zmiennych) W drugim etapie do powyższych zmiennych decyzyjnych procesu optymalizacyjnego dołączono wymiary tłoka oraz parametry konstrukcyjne...
-
Geothermal heating plant with a combustion engine heat pump.
PublicationPrzedstawiono koncepcję ciepłowni geotermalnej zagospodarowującej zasoby energii zawarte w nisko i średniotemperaturowej wodzie termalnej. W tym celu zaproponowano zastosowanie pompy grzejnej napędzanej silnikiem spalinowym.
-
Tests of a Steam Piston Engine Under Supercritical Conditions
Publication -
Process of self-ignition engine loads and its properties
PublicationW artykule zaproponowano probabilistyczną interpretację obciążenia silników spalinowych o zapłonie samoczynnym z uwzględnieniem znanych parametrów (wskaźników) ich pracy. Wykazano, że obciążenie tego rodzaju silników, rozpatrywane w dowolnej chwili, może być uważane za zmienną losową wielowymiarową. Zmiany obciążenia silnika w czasie jego pracy uznane zostały za proces obciążeń i przedstawione w formie wielowymiarowego procesu...
-
Dimensionless Analysis of Stirling Engine using of Optimization Methods
PublicationW pracy zaprezetowano wyniki analizy wpływu parametrów konstrukcyjnych silnika Stirlinga na jego wskaźniki jakości.Analizę przeprowadzono na modelu bezwymiarowym wykorzystując metody optymalizacji parametrycznej.
-
The automation of test stand for engine cooling system testing
PublicationW rozdziale przedstawiono budowę stanowiska do badań układu chłodzenia silnika samochodowego typu M111920. Układ był wyposażony w obwód podgrzewania paliwa gazowego i układ akumulacji ciepła. Stanowisko wyposażono w liczne termopary do pomiaru temperatur płynów i części metalowych silnika. Ważnym opracowanym zagadnieniem było rejestrowanie wielu pomiarów w czasie rzeczywistym, do czego użyto sieci transmisji danych CAN.
-
A concept of the predicting of technical state of diesel engine elements
PublicationPrzedstawiono możliwości i ograniczenia dotyczące prognozowania stanu technicznego elementów silników oraz wykazano potrzebę doskonalenia istniejących metod planowania ich obsług profilaktycznych. Wskazano możliwość przekształcenia rozkadów szybkości zużywania elementów silników na rozkłady czasu ich poprawnego działania do osiągnięcia stanu granicznego w celu prognozowania ich stanu technicznego i odpowiedniego planowania obsług.
-
High-Speed Binary-to-Residue Converter Design Using 2-Bit Segmentation of the Input Word
PublicationIn this paper a new approach to the design of the high-speed binary-to-residue converter is proposed that allows the attaining of high pipelining rates by eliminating memories used in modulo m generators. The converter algorithm uses segmentation of the input binary word into 2-bit segments. The use and effects of the input word segmentation for the synthesis of converters for five-bit moduli are presented. For the number represented...
-
An Experimentally Aided Operational Virtual Prototyping to Obtain the Best Spindle Speed during Face Milling of Large-Size Structures
PublicationAbstract: The paper presents an original method concerning the problem of vibration reduction in the general case while milling large-size and geometrically complex details with the use of an innovative approach to the selection of spindle speed. A computational model is obtained by applying the so-called operational approach to identify the parameters of the workpiece modal model. Thanks to the experimental modal analysis results,...
-
A technique of experiment aided virtual prototyping to obtain the best spindle speed during face milling of large-size structures
PublicationThe paper presents an original method concerning vibration suppression problem during milling of large-size and geometrically complicated workpieces with the use of novel way of selecting the spindle speed. This consists in repetitive simulations of the cutting process for subsequent values of the spindle speed, until the best vibration state of the workpiece is reached. An appropriate method of obtaining a computational model,...
-
A method for evaluating the performance of a marine piston internal combustion engine used as the main engine on a ship during its voyage in different sailing conditions
PublicationPrzedstawiono metodę oceny działania tłokowych silników spalinowych napędu głównego staków morskich, nazywanych silnikami głównymi, działających w typowych warunkach ich eksploatacji. Warunki te zostały opisane z uwzględnieniem pola osiągów tego rodzaju silników. Metoda ta umożliwia obliczenie wartości działania w wyniku zastosowania rachunku całkowego. Znamienne jest to, że działanie wspomnianych silników spalinowych zostało przyrównane...
-
Simple observer for induction motor speed sensorless control
PublicationPrzedstawiono układ sterowania polowo zorientowanego silnikiem asynchronicznym klatkowym pozwalający na pracę w szerokim zakresie prędkości obrotowych bez użycia czujnika prędkości. Zaproponowano estymator zmiennych o prostej strukturze charakteryzujący się znaczna odpornością na zmiany parametrów silnika. Zależności obserwatora oparte są na równaniach obwodu napięciowego silnika. Pokazano wyniki badań eksperymentalnych.
-
The spindle speed optimal control in modern milling operations.
PublicationPraca dotyczy modeli obrabiarek ze sprzężeniem zwrotnym, w przypadku których istotne znaczenie mają drgania samowzbudne typu chatter. Opis układu drgającego przedstawiono w postaci dynamiki układu sterowanego, przy czym sygnałem sterującym jest chwilowa zmiana prędkości obrotowej wrzeciona. Rozważano frezowanie czołowe smukłym frezem trzpieniowym na pionowym cent rum frezarskim. Przedstawiono rezultaty przykładów symulacji komputerowych....
-
High-speed binary-to-residue converter with improved architecture.
PublicationPrzedstawiono ulepszoną architekturę szybkiego konwertera liczb z systemu binarnego do systemu resztowego dla liczb ze znakiem w kodzie U2. Algorytm konwertera oparty jest o segmentację słowa wejsciowego nasegmenty 4-bitowe. Reszty liczb reprezentowanych przez segmenty sąobliczane poprzez odwzorowanie. Wielooperandowe sumowanie modulo jest realizowane przy użyciu drzewa Wallace'a z segmentacją wektorów wyjściowych oraz finalnego...
-
Sensorless multiscalar controls of induction motor at low speed
PublicationW artykule przedstawiono zastosowanie obserwatora prędkości w dwóch różnych układach sterowania multiskalarnego silnikiem klatkowym. Pierwszy układ bazuje na prądzie stojana i strumieniu wirnika, natomiast drugi nowy układ wykorzystuje zmienne prąd stojana i strumień stojana. Zamieszczono wyniki badań symulacyjnych i eksperymentalych w układzie ze sterowaniem na procesorze SHARC.
-
Speed monitoring and management in national road safety program
PublicationW referacie przedstawiono system długoterminowych badań prędkości pojazdów umozliwiający śledzenie ich zmian. Zmiany te są analizowane w powiązaniu z wdrażanymi środkami nadzoru oraz edukacyjnymi oddziaływaniami na uczestników ruchu, a także ze zmianami infrastruktury drogowej. Podano też ogólne zalecenia do programu GAMBIT 2005, wynikające z dotychczasowych badań prędkości.
-
Programmed control of the spindle speed in modern milling machines.
PublicationW pracy przedstawiono nowe podejście do nadzorowania drgań wirujących narzędzi we współczesnych frezarkach. Polega ono na sterowaniu programowym w układach niestacjonarnych. Dotyczy to zamkniętych układów obrabiarek, kiedy to istotną rolę odgrywają drgania samowzbudne typu chatter. Sygnałem sterującym jest chwilowa zmiana prędkości obrotowej. Rozważano frezowanie czołowe smukłym frezem trzpieniowym na pionowym centrum frezarskim....