Filters
total: 635
filtered: 621
Search results for: MODELLING DYNAMICS
-
Modeling and experimental investigation of the small UPQC systems
PublicationIn this paper the basis of analytical modelling of the UPQC arrangements (Unified Power Quality Conditioner) in d-q rotating coordinates, as well as select results of investigations conducted on the simplified small power laboratory model were talked over. In short form power balance as well as fundamental dependences and analytic model with regard of decoupling circuits were investigated. Applied method for DC link capacity selection...
-
Modelling of heat and mass transfer through wooden buildings
PublicationThe aim of this review paper is to examine the most recent available studies dealing with theoretical, numerical and experimental aspects related to modelling of heat and mass transfer through wooden buildings. The main thermophysical, mechanical and hygrometric properties of wood are firstly discussed. Then, the basic governing equations of heat and mass transfer phenomena are presented. A detailed description of the physical...
-
Numerical simulation of the influence of the selected factors on the performance of a concrete road barrier H2/W5/B
PublicationThis paper discuss the influence of selected factors on the performance of a concrete road barrier H2/W5/B. Modelling techniques of a concrete road safety system were briefly discussed. Comparison to the full scale crash test results has been shown. The concrete road safety barrier has been investigated for evaluation of the overall damage after collision under various initial conditions. The failure assessment criterion has been...
-
Modelling of performance of an AUV stealth vehicle. Design for operation.
PublicationIn the paper some results of research connected with modelling of performance and risk assessment of an AUV stealth vehicle are presented. A general approach to design of the stealth AUV autonomous underwater vehicle under consideration is introduced. The basic stealth characteristics of the AUV stealth vehicle are briefly described. The method of research is introduced. The AUV stealth vehicle concept is presented including the...
-
Modeling of performance of an AUV stealth vehicle. Design for operation.
PublicationIn the paper some results of research connected with modelling of performance and risk assessment of an AUV stealth vehicle are presented. A general approach to design of the stealth AUV autonomous underwater vehicle under consideration is introduced. The basic stealth characteristics of the AUV stealth vehicle are briefly described. The method of research is introduced. The AUV stealth vehicle concept is presented including the...
-
Scientific research in the Department of Machine Design and Automotive Engineering
PublicationShort descriptions of various research subjects taken up at the Department of Machine Design and Automotive Engineering are included in the paper. The subjects cover a wide range of bearing systems and tribology research and the research on tires and road surfaces. A third field of activity is biomedical engineering – with the attempts to improve methods of modelling biological materials in FEM calculations. The Department has...
-
GPR simulations for diagnostics of a reinforced concrete beam
PublicationThe most popular technique for modelling of an electromagnetic field, the finite difference time domain (FDTD) method, has recently become a popular technique as an interpretation tool for ground penetrating radar (GPR) measurements. The aim of this study is to detect the size and the position of damage in a reinforced concrete beam using GPR maps. Numerical simulations were carried out using the finite differ-ence time domain...
-
Acoustic journal bearing - A search for adequate configuration
PublicationClassical non-contact bearings are already used in a number of specialist applications but there are somespecialist areas where they cannot be used for variety of reasons and acoustic sliding bearings could be an alternative. The paper presents the quest for a configuration of an acoustic journal bearing and shows that the overall shape of the bearing and its geometry are of a vital importance for the load capacity oft he bearing....
-
Knowledge-Grid Modelling for Academic Purposes
PublicationNowadays, we face a huge amount of data and information sharing on the Web by different users worldwide. A multidimensional perspective in describing a university ontology seems to be very important for the modelling of higher education resources. This paper proposes a multi-dimensional knowledge model, designed to distribute and manage knowledge resources efficiently. We propose our model as the foundation of an advanced knowledge...
-
Pre-selection and assessment of green organic solvents by clustering chemometric tools
PublicationThe study presents the result of the application of chemometric tools for selection of physicochemical parameters of solvents for predicting missing variables – bioconcentration factors, water-octanol and octanol-air partitioning constants. EPI Suite software was successfully applied to predict missing values for solvents commonly considered as “green”. Values for logBCF, logKOW and logKOA were modelled for 43 rather nonpolar solvents...
-
Long-term Hindcast Simulation of Currents, Sea Level, Water Temperature and Salinity in the Baltic Sea
PublicationThis dataset contains the results of numerical modelling of currents, sea level, water temperature and salinity over a period of 50 years (1958–2007) in the Baltic Sea. A long-term hindcast simulation was performed using a three-dimensional hydrodynamic model (PM3D) based on the Princeton Ocean Model (POM). The spatial resolution was 3 nautical miles, i.e. about 5.5 km. Currents, water temperature, and salinity were recorded...
-
Software tool for modelling of mechatronic systems with elastic continua
PublicationThe paper presents a systematic computational package for modelling and analysis of complex systems composed of multiple lumped and distributed parameter subsystems. The constructed computer program enables the frequency domain analysis of a class of linear systems and to obtain reduced order model in the form of bond graph. Obtained modal bond graph can be directly exported into 20-Sim package to further processing including nonlinear...
-
Experiments and numerical modeling of meat and bone meal pyrolysis in a rotary kiln
PublicationThe paper presents aspects of modelling the pyrolysis of meat and bone meal (MBM) in a rotary kiln. The pyrolysis of MBM produces a solid fraction which can be used as a fuel, a liquid fraction with potential chemical applications and a low heating value gas. The meat and bone meal pyrolysis was carried out at the temperature of 900 oC. Main features of experiments and numerical model of the pyrolysis were described. The model...
-
Spirometry measurement model - the diagnostic purpose support
Publicationthe paper presents a new model of respiratory mechanism based on the spirometry measurements. the spirometry test assesses the efficiency of the lung ventilation. the respiratory system functioning is based on the ventilation mechanism. thus the quality of the lung depends on the quality of lung ventilation. modelling of the respiratory system supports a diagnostic process. the model parameter estimates are obtained on the basis...
-
Design of power cable lines partially exposed to direct solar radiation – special aspects
PublicationPower cable lines are usually buried in the ground. However, in some cases, their ending sections are mounted along the supports of overhead lines. This leads to a situation where the cables are exposed to direct solar radiation and, consequentially, overheat. The paper presents the advanced computer modelling of power cables’ heating, considering their insolation as well as the effect of wind. The temperature and current-carrying...
-
Comparative Study of Balancing SRT by Using Modified ASM2d in Control and Operation Strategy at Full-Scale WWTP
PublicationDetailed knowledge on the composition of the influent going into the wastewater treatment system is essential for the development of a reliable computer model. In the context of WWTPs (wastewater treatment plants), the wastewater characteristics are not only important for activated sludge system modelling, but also have an impact on the appropriate control of single unit operations. The aim of this study was to evaluate the concepts...
-
Expedited constrained multi-objective aerodynamic shape optimization by means of physics-based surrogates
PublicationIn the paper, computationally efficient constrained multi-objective design optimization of transonic airfoil profiles is considered. Our methodology focuses on fixed-lift design aimed at finding the best possible trade-offs between the two objectives: minimization of the drag coefficient and maximization of the pitching moment. The algorithm presented here exploits the surrogate-based optimization principle, variable-fidelity computational...
-
Evolutionary Sets of Safe Ship Trajectories: Evaluation of Individuals
PublicationThe paper presents a description of the evaluation phase of the Evolutionary Sets of Safe Ship Trajectories method. In general, the Evolutionary Sets of Safe Ship Trajectories method combines some of the assumptions of game theory with evolutionary programming and finds an optimal set of cooperating trajectories of all ships involved in an encounter situation. While developing a new version of this method, the authors decided to...
-
Spectral Methods for Modelling of Wave Propagation in Structures in Terms of Damage Detection—A Review
PublicationModern methods of detection and identification of structural damage direct the activities of scientific groups towards the improvement of diagnostic methods using for example the phenomenon of mechanical wave propagation. Damage detection methods that use mechanical wave propagation in structural components are extremely effective. Many different numerical approaches are used to model this phenomenon, but, due to their universal...
-
The Effect of Protrusions on the Initiation of Partial Discharges in XLPE High Voltage Cables
PublicationThis paper is focusing on 3D Finite Elements Analysis (FEA) based modelling of protrusions as defects or imperfections in the XLPE high voltage cable. This study is aiming to examine the impact protrusions have on the initiation of partial discharges. Spherical and ellipsoidal protrusions with different sizes at the conductor screen of the high voltage cable is an essential content of this paper. In addition, a spherical gas-filled...
-
Electromagnetic interference frequencies prediction model of flyback converter for snubber design
PublicationSnubber design for flyback converters usually requires experimental prototype measurements or simulation based on accurate and complex models. In this study simplified circuit modelling of a flyback converter has been described to dimension snubbers in early stage of design process. Simulation based prediction of the transistor and diode ringing frequencies has been validated by measurements in a prototype setup. In that way obtained...
-
Complexity analysis of the Pawlak’s flowgraph extension for re-identification in multi-camera surveillance system
PublicationThe idea of Pawlak’s flowgraph turned out to be a useful and convenient container for a knowledge of objects’ behaviour and movements within the area observed with a multi-camera surveillance system. Utilization of the flowgraph for modelling behaviour admittedly requires certain extensions and enhancements, but it allows for combining many rules into a one data structure and for obtaining parameters describing how objects tend...
-
GENERALISED HERSCHEL MODEL APPLIED TO BLOOD FLOW MODELLING
PublicationThis paper introduces a new rheological model of blood as a certain generalisation of the standard Herschel-Bulkley model. This model is a rheological constitutive equation and belongs to the group of the so-called generalised Newtonian fluids. Experimental data is compared with results, obtained from the new model, to demonstrate that it allows for the best agreement together with Luo-Kuang model. The new model may be easily implemented...
-
A two dimensional approach for modelling of pennate muscle behaviour
PublicationThe purpose of this study was to elaborate a two-dimensional approach for unipennate and bipennate striated skeletal muscle modelling. Behavior of chosen flat pennate muscle is modelled as a rheological system composed of serially linked passive and active fragments having different mechanical properties. Each fragment is composed of three elements: mass element, elastic element and viscous element. Each active fragment furthermore...
-
Modelling of joining route segments of differential curvature
PublicationThe paper presents a new general method of modelling route segments curvature using differential equations. The method enables joining of route segments of different curvature. Transitional curves of linear and nonlinear curvatures have been identified in the case of joining two circular arcs by S-shaped and C-oval transitions. The obtained S-shaped curves have been compared to the cubic C-Bezier curves and to the Pythagorean hodograph...
-
The effect of current delay angle on tripping of residual current devices
PublicationPower electronics converters applied in domestic or similar installations may utilize current delay (phase) angle control to change the level of transferred power. Due to application of such types of converters, earth fault current in the installation may be strongly distorted. The current distortion level depends on a value of current delay angle. This delay angle also influences the tripping threshold of residual current devices....
-
On phase equilibrium of an elastic liquid shell with wedge disclination
PublicationBased on the six-parameter shell theory we consider the phase equilibrium of a two-phase liquid membrane containing a wedge disclination. The considered problems are related to modelling of phase transitions in biological or lipid membranes. In order to capture the membrane behaviour we consider a special case of elastic shells which energy is invariant under major transformations of a reference configuration and can be treated...
-
Polyarmonic model of synchronous generator for analysis of autonomous power generation systems
PublicationAbstract: This paper presents the polyharmonic modelling of synchronous generator (SG) in machine variables. The simple geometry and windings physical layout has been used for inductance calculations of a salient-pole SG. The main advantage of this model is the ease of describing an autonomous power generation system (APGS) in terms of its topology and thus providing effective analysis at the static and dynamic states, both for...
-
Experimentation, material modelling and simulation of bonded joints with a flexible adhesive
PublicationThe paper deals with material parameters identification of a flexible adhesive and the numerical simulation of its behaviour in a single lap bonded joint. The material modelling was based on the simple shear and tensile-shear laboratory tests of the bonded joints made of thin aluminium and polyurethane plates with the flexible adhesive Terostat MS 9360 manufactured by Henkel AG & Co. The adhesive was considered as a hyperelastic...
-
Modification of Selected Propagation Models in Terms of Path Loss Estimation in Container Terminal
PublicationIt is particularly important to look for any propagation model that could be useful for designing mobile radio networks in container terminal environment. Selected propagation models have been investigated. Firstly - basing on measurements results - they have been evaluated in this scope and the analysis has shown, that the adjustment is needed. This modification improved significantly the accuracy of path loss modelling. For the...
-
Non-linear circuit model of a single doubly-fed induction machine formulated in natural axes for drive systems simulation purposes
PublicationMathematical modelling and a circuit model formulated in natural axes of a single doubly-fed induction machine, with the account of magnetic circuit nonlinearity are presented in the paper. Derivation of the model differential equations was based on Lagrange's energy method. State functions of magnetic elements in the model are non-linear and depend on all currents flowing in the machine windings and on the angle of rotor position....
-
CFGFRPT Piles with a Circular Cross-Section and their Application in Offshore Structures
PublicationThe possibilities of using concrete piles in a polymer composite reinforced with glass fibres in offshore facilities were shown. Laboratory tests of CFGFRPT type piles compressed axially and in eccentric compression for the analysis of CFGFRPT piles were used. Methods of analysis of dynamic systems for mathematical modelling of the displacement of the hammer in the pile driving process were applied. The possibilities of combining...
-
Electromagnetic-based derivation of fractional-order circuit theory
PublicationIn this paper, foundations of the fractional-order circuit theory are revisited. Although many papers have been devoted to fractional-order modelling of electrical circuits, there are relatively few foundations for such an approach. Therefore, we derive fractional-order lumped-element equations for capacitors, inductors and resistors, as well as Kirchhoff’s voltage and current laws using quasi-static approximations of fractional-order...
-
Impact of thermal loading into the structural performance of ships: A review
PublicationThe presented study reviews the recent advances done regarding the impact of thermal loading on the structural performance of ships. Firstly, the studies related to the mechanical and thermal properties of typical materials used in shipbuilding are outlined. Secondly, a brief introduction to the heat transfer analysis, Finite Element modelling and thermal stresses is provided. Finally, the review of papers dealing with the structural...
-
Modelling of Nuclear Power Plant Steam Turbine
PublicationThe paper describes the approach to a Nuclear Power Plant steam turbine modelling which would enable on-line optimal process control (model based) and diagnosis over wide range of operating conditions caused by changing power demand. Presented model is static, multivariable and nonlinear. Such model enables analyzing the heat cogeneration aspects. Developed model is validated and verified by using archive data gained from researches...
-
Modelling of Nuclear Power Plant Steam Turbine
PublicationThe paper describes the approach to a Nuclear Power Plant steam turbine modelling which would enable on-line optimal process control (model based) and diagnosis over wide range of operating conditions caused by changing power demand. Presented model is static, multivariable and nonlinear. Such model enables analyzing the heat cogeneration aspects. Developed model is validated and verified by using archive data gained from researches...
-
The use of mathematical models for diagnosis of activated sludge systems in WWTP
PublicationIn this study diagnosis of activated sludge systems in wastewater treatment plant (WWTP) was investigated. Diagnosis of technical objects can be realized in many ways. One of the divisions of the diagnostic methods include modelling with or without a model of the object. The first of these is the analysis of the symptoms for which, based on the parameter values, the abnormality in the diagnosed objects are sought. Another way is...
-
Different sources of market information and product innovativeness
PublicationThe purpose of this study is to identify whether the gathering of market information from different sources – i.e. from customers, competitors and other entities – is related to product innovativeness. The relationships proposed so far have not been empirically investigated but they can have important theoretical and practical implications for product innovation. To achieve the purpose of the paper data concerning 287 new products...
-
Shape Optimisation of Kaplan Turbine Blades Using Genetic Algorithms
PublicationThis monograph is a comprehensive guide to a method of blade profile optimisation for Kaplan-type turbines. This method is based on modelling the interaction between rotor and stator blades. Additionally, the shape of the draft tube is investigated. The influence of the periodic boundary condition vs. full geometry is also discussed. Evolutionary algorithms (EA) are used as an optimisation method together with artificial neural...
-
Nested Kriging Surrogates for Rapid Multi-Objective Optimization of Compact Microwave Components
PublicationA procedure for rapid EM-based multi-objective optimization of compact microwave components is presented. Our methodology employs a recently developed nested kriging modelling to identify the search space region containing the Pareto-optimal designs, and to construct a fast surrogate model. The latter permits determination of the initial Pareto set, further refined using a separate surrogate-assisted process. As an illustration,...
-
Modelling, Simulation and Optimization of the Wavemaker in a Towing Tank
PublicationThe paper analyses the problem of experimental identification (frequency response), modelling and optimization of the towing tank wavemaker in the Scilab/Xcos environment. The experimental identification of the objects (the towing tank wavemaker placed in the hydrodynamic laboratory of the CTO S.A. Ship Design and Research Centre (CTO)) and the implementation of the models in the simulation environment, enable to perform: 1. tuning...
-
The modelling method of discrete-continuous systems
PublicationThe paper introduces a method of discrete-continuous systems modelling. In the proposed method a three-dimensional system is divided into finite elements in only two directions, with the third direction remaining continuous. The thus obtained discrete-continuous model is described by a set of partial differential equations. General difference equations of discrete system are obtained using the rigid finite element method. The limit...
-
Evolutionary Sets of Safe Ship Trajectories: Evaluation of Individuals
PublicationThe paper presents a description of the evaluation phase of the Evolutionary Sets of Safe Ship Trajectories method. In general, the Evolutionary Sets of Safe Ship Trajectories method combines some of the assumptions of game theory with evolutionary programming and finds an optimal set of cooperating trajectories of all ships involved in an encounter situation. While developing a new version of this method, the au-thors decided...
-
Application of Pierson-Moskowitz wave spectrum to solution differential equations of multihull vessel
PublicationMotion of a dynamic system can be generated by different external or internal factors. At mathematical modelling external excitation factors of the most significant effect on the system, are selected. Such external factors are usually called excitations. Response of the system to given excitations is mathematically characterized by a definite transformation called operator of a system. For a broad class of dynamic systems the...
-
The application of nonlinear curvature sections in the turnout diverging track
PublicationThe paper presents the analytical method of modelling the diverging track of railway turnout with nonlinear curvature sections. These sections were used for smoothing the graph of curvature in the extreme areas of turnout. The problem of the curvature distribution was identified with the use of differential equations. The resulting solutions are of universal nature for example the ability of assuming any values of curvature at...
-
A comparative performance assessment of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublicationThis work presents the investigation results of a journal bearing lubricated with magnetorheological fluid that is activated by a local constant magnetic field to vary both the local flow resistance and pressure. The bearing performance is assessed via Finite Element Modelling (FEM) and results are corroborated by experiments. The FEM model uses the Bingham model to describe the fluid film. A dedicated test rig is used to assess...
-
The Use of Cluster Analysis to Evaluate the Impact of COVID-19 Pandemic on Daily Water Demand Patterns
PublicationProper determination of unitary water demand and diurnal distribution of water consumption (water consumption histogram) provides the basis for designing, dimensioning, and all analyses of water supply networks. It is important in the case of mathematical modelling of flows in the water supply network, particularly during the determination of nodal water demands in the context of Extended Period Simulation (EPS). Considering the...
-
Global Optimization for Recovery of Clipped Signals Corrupted With Poisson-Gaussian Noise
PublicationWe study a variational formulation for reconstructing nonlinearly distorted signals corrupted with a Poisson-Gaussian noise. In this situation, the data fidelity term consists of a sum of a weighted least squares term and a logarithmic one. Both of them are precomposed by a nonlinearity, modelling a clipping effect, which is assumed to be rational. A regularization term, being a piecewise rational approximation of the ℓ0 function...
-
AN INNOVATIVE APPROACH TO PREDICTION ENERGETIC EFFECTS OF WOOD CUTTING PROCESS WITH CIRCULAR-SAW BLADES
PublicationIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. The aim of the paper is to present a new calculating model using the application of modern fracture mechanics and to compare cutting parameters of native beech, Bendywood...
-
Reaction of aniline with ammonium persulphate and concentrated hydrochloric acid: Experimental and DFT studies
PublicationIn this paper, the reaction of aniline with ammonium persulphate and concentrated HCl was studied. As a result of our experimental studies, 2,4,6-trichlorophenylamine was identified as the main product. This shows that a high concentration of HCl does not favour oxidative polymerisation of phenylamine, even though the ammonium persulphate/HCl system is widely used in polyaniline synthesis. On the basis of the experimental data...