Filters
total: 3632
filtered: 3078
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: power factor correction
-
Effect of pine impregnation and feed speed on sound level and cutting power in wood sawing
PublicationThe sound levels along with the cutting power registered during the sawing process of the impregnated and non-impregnated pine wood at two feed speeds are shown and compared in this paper. Statistically significant differences in the acoustic signals occurred at the lower feed rate. The differences became smaller with an increase in the feed speed. In contrast to the sound signal, the differences...
-
Overheating of underground power cable line due to its partial exposition to solar radiation
PublicationCurrent-carrying capacity of underground power cable lines depends, among others, on thermal resistivity of the soil and cables layout: trefoil formation, flat formation with or without spacing. If conditions for heat transfer in the ground are favorable, the current-carrying capacity is relatively high. Therefore, it generates risk of the power cables overheating, if part of the cable line is located vertically in the air, to...
-
Effect of hybrid contactless short-cicruit limiters on power quality
PublicationPrzedstawiono działanie bezstykowego ogranicznika prądów zwarciowych w oparciu o symulację komputerową. Szczególną uwagę zwrócono na problem jakości dostarczanej energii elektrycznej poprzez ograniczanie zapadów napięcia za pomocą bezstykowego ogranicznika prądów zwarciowych. W modelowaniu elementów systemu elektroenergetycznego i zapadów napięcia, będących skutkiem zwarć wykorzystano program MATLAB z biblioteką Power System Blockset....
-
Experimental test results of the 150kVA 18-pulse diode rectifier with series active power filter
PublicationThe paper presents the control system and selected results of experimental tests of the ac/dc power converter consisting of 18-pulse diode rectifier on the basis of coupled reactors and a serial active power filter. Three configurations of the 150kVA converter were tested experimentally and compared: 18-pulse diode rectifier with and without additional grid reactor and the rectifier integrated with the active power filter. The...
-
Low-cost and reliable geometry scaling of compact microstrip couplers with respect to operating frequency, power split ratio, and dielectric substrate parameters
PublicationA technique for rapid re-design of miniaturised microstrip couplers with respect to operating conditions as well as material parameters of the dielectric substrate is proposed. The dimension scaling process is based on a set of pre-optimised reference designs, obtained for an equivalent circuit model of the coupler at hand. The reference designs are utilised to construct an inverse surrogate model which – upon suitable correction...
-
Power Surge Compensator based on a Four Level Diode Clamped Inverter for ship application. Average model
PublicationPaper presents continuous average value model of Power Surge Compensator based on a Four Level Diode Clamped Inverter with super capacitor as a energy storage device. This conditioner is design for power surge or fluctuation elimination, by compensating it with energy stored in ESD. Continuous average value model of multilevel S-PWM has been presented also. Summary of raised problem is a simulation model made in PowerSim Psim 8...
-
Multi-nodal PWR reactor model — Methodology proposition for power distribution coefficients calculation
PublicationIn the paper the multi-nodal Pressurized Water Reactor (PWR) model called Mann’s model is presented. This models is used for modelling purposes of the heat transfer from fuel to coolant in reactor core. The authors expand widely used in literature approach by defining additional coefficients for the heat transfer model. These parameters approximate the power generation distribution in the PWR reactor core according to the to the...
-
A new method of wind farm active power curve estimation based on statistical approach
PublicationThe purpose of this paper is to solve the wind farm active power estimation problem, introducing the method which is based on a statistical approach and robust fitting. The proposed algorithm uses a statistical approach and compared to existing ones- includes a wind direction as well as the influence of turbine start-up procedure on the estimation. The results show that additional estimation inputs i.e. the wind direction and the...
-
Technical and Economic Analysis of an Intermediate Size Photovoltaic Power Plant. Case Study
PublicationThe article presents an analysis of the construction of a photovoltaic power plant with an installed capacity of about 30 kW. The principles of selecting the basic elements of the plant are shown. The impact of a high constant price on the profitability of the project is highlighted. The article also describes the existing mechanisms for subsidizing the investment.
-
Simulating Power Generation from Photovoltaics in the Polish Power System Based on Ground Meteorological Measurements—First Tests Based on Transmission System Operator Data
PublicationThe Polish power system is undergoing a slow process of transformation from coal to one that is renewables dominated. Although coal will remain a fundamental fuel in the coming years, the recent upsurge in installed capacity of photovoltaic (PV) systems should draw significant attention. Owning to the fact that the Polish Transmission System Operator recently published the PV hourly generation time series in this article, we aim...
-
Comprehensive compensation of grid current distortion by shunt active power filters
PublicationThe paper presents a comprehensive approach to the compensation of grid current distortion in shunt active power filter systems. Four sources of current distortion are addressed: imperfect grid synchronization caused by the distortion in the grid voltages, time delays in the evaluation of grid voltages and computation of compensating currents, fluctuations of the dc bus voltage, and the distortion of inverter output voltages due...
-
Induction Generator with Direct Control and a Limited Number of Measurements on the Side of the Converter Connected to the Power Grid
PublicationThe article presents an induction generator connected to the power grid using the AC/DC/AC converter and LCL coupling filter. Three-level inverters were used in the converter, both from the generator side and the power grid side. The algorithm realizing Pulse Width Modulation (PWM) in inverters has been simplified to the maximum. Control of the induction generator was based on the Direct Field-Oriented Control (DFOC) method. At...
-
High power, zero ripples active filtering system with power modules operating in parallel
Publication -
Hydraulic servomechanism system. Examples of reduction of power losses in the variable pressure power supply
PublicationUkład serwomechanizmu hydraulicznego najczęściej stosowany, w którym rozdzielacz dławiący jest zasilany pompą wyporową o stałej wydajności, współpracującą z zaworem przelewowym, pracujący przy stałym ciśnieniu zasilania, osiąga wysoką wartość sprawności energetycznej jedynie w punkcie maksymalnej wartości obciążenia i prędkości sterowanego silnika. Oszczędności energii przy zasilaniu układu pompą o stałej wydajności mogą być osiągnięte...
-
Power Hardware In-the-Loop validation of DC-DC power converter for offshore wind energy
Publication -
Optimal Placement of Phasor Measurement Unit in Power System using Meta-Heuristic Algorithms
PublicationThe phasor measurement units (PMUs) play an important and vital role in power system monitoring and controlling, since they provide the power system phasors stamped with a common real time reference through a global positioning system (GPS). Indeed, from economical point of view it is not possible to set PMUs in all system buses due to the high cost and the requirement of more complex communication...
-
Heat Dissipation from the Power Cable in the Casing Pipe
PublicationThe current carrying capacity of a power cable determines its ability to carry a specific current and is related to the efficiency of dissipation of heat generated in the cable laid in a specific environment. The studies were conducted in order to determine how the characteristics of the medium around the cable affected its temperature, and thus the ability of the cable to transmit electricity. The experimentation in the lab and...
-
SiC-Based Power Electronic Traction Transformer (PETT) for 3 kV DC Rail Traction
PublicationThe design of rolling stock plays a key role in the attractiveness of the rail transport. Train design must strictly meet the requirements of rail operators to ensure high quality and cost-eective services. Semiconductor power devices made from silicon carbide (SiC) have reached a level of technology enabling their widespread use in traction power converters. SiC transistors oering energy savings, quieter operation, improved reliability...
-
Power System Stabilizer as a Part of a Generator MPC Adaptive Predictive Control System
PublicationIn this paper, a model predictive controller based on a generator model for prediction purposes is proposed to replace a standard generator controller with a stabilizer of a power system. Such a local controller utilizes an input-output model of the system taking into consideration not only a generator voltage Ug but also an additional, auxiliary signal (e.g., α, Pg, or ωg). This additional piece of information allows for taking...
-
Nuclear Power Plant Steam Turbine - Modeling for Model Based Control Purposes
PublicationThe nature of the processes taking place in a nuclear power plant (NPP) steam turbine is the reason why their modeling is very difficult, especially when the model is intended to be used for on-line optimal model based process control over a wide range of operating conditions, caused by changing electrical power demand e.g. when combined heat and power mode of work is utilized. The paper presents three nonlinear models of NPP steam...
-
A study of a compact high-efficiency zero-emission power plant with oxy-fuel combustion
PublicationThis paper discusses the application of global trends in gas cycles technology using oxy-fuel combustion. This is followed by a demonstration of a design solution for a new cycle with two enhanced energy-converting devices, namely a wet combustion chamber and a spray-ejector condenser. The proposed gas and steam cycle unit is contained within a single turbine, whose benefits combine those offered by gas turbines (high inlet temperatures)...
-
Calculation of Induced Sheath Voltages in Power Cables – Single Circuit System versus Double Circuit System
PublicationThis paper presents comparison of values of induced sheath voltages in power cable metallic sheaths when one or two cables per phase are used. Calculation of voltages is performed for various phase sequences of the power cables. Three types of the sheaths bonding and earthing are considered. Shock hazard and voltage stress of non-metallic outer sheath of cables are evaluated. The proposed, optimal configuration of the power cable...
-
Optimization of Execution Time under Power Consumption Constraints in a Heterogeneous Parallel System with GPUs and CPUs
PublicationThe paper proposes an approach for parallelization of computations across a collection of clusters with heterogeneous nodes with both GPUs and CPUs. The proposed system partitions input data into chunks and assigns to par- ticular devices for processing using OpenCL kernels defined by the user. The sys- tem is able to minimize the execution time of the application while maintaining the power consumption of the utilized GPUs and...
-
Selection of optimal location and rated power of capacitor banks in distribution network using genetic algorithm
PublicationIn this paper, the problem of placement and rated power of capacitor banks in the Distribution Network (DN) is considered. We try to suggest the best places for installing capacitor banks and define their reactive power. The considered formulation requires the optimization of the cost of two different objectives. Therefore the use of properly multiobjective heuristic optimization methods is desirable. To solve this problem we use...
-
Power balance in hydraulic satellite motors supplied with oil and HFA-E emulsion
PublicationMineral oil and HFA-E emulsion are liquids which differ in viscosity, density and lubricant properties. Therefore, supplying hydraulic satellite motors with these liquids, differences between quantity of hydraulic, volumetric and mechanical losses are observed. These losses influence efficiency of conversion of hydraulic energy into mechanical energy and thereby power balance of motors.
-
Correction: Highly stable organic–inorganic junction composed of hydrogenated titania nanotubes infiltrated by a conducting polymer
Publication -
<title>Correction of fiber optic ion sensor readings using a fiber optic temperature sensor</title>
Publication -
Effect of Time Varying Measurement Conditions on Antenna Pattern in Near Field Measurement and Its Correction Procedure
PublicationAuthors present the procedure of taking into account the changes of electrical parameters of setup due to the time drift of temperature during the procedure of near field measurement. It is proposed to make additional measurements in determined positions of probe are next used the results to introduce corrections terms in measured data. Such approach was verified practically in experimental near field measurement system.
-
A CMOS Pixel With Embedded ADC, Digital CDS and Gain Correction Capability for Massively Parallel Imaging Array
PublicationIn the paper, a CMOS pixel has been proposed for imaging arrays with massively parallel image acquisition and simultaneous compensation of dark signal nonuniformity (DSNU) as well as photoresponse nonuniformity (PRNU). In our solution the pixel contains all necessary functional blocks: a photosensor and an analog-to-digital converter (ADC) with built-in correlated double sampling (CDS) integrated together. It is implemented in...
-
Diagnosis in the power piston machines
PublicationW artykule przedstawiono obecne techniki monitorowania pracy silników i sprężarek dużej mocy. Ze względu na znaczne koszty ewentualnego wyłączenia z ruchu tego typu maszyn są one poddane obserwacji dla przewidywania ewentualnych awarii oraz planowych zatrzymań. Rośnie liczba zaawansowanych systemów pomiarowych z indykowaniem cylindrów. Dawne metody wibroakustyczne zastępowane są pomiarami parametrów procesu termodynamicznego. Słowa...
-
Computer synchronization of power generators
PublicationAktualną staje się kwestia opracowania odpowiednich algorytmów pomiarów i obliczeń, według których będzie możliwe prowadzenie procesu automatycznej synchronizacji bezpośrednio z wykorzystaniem komputera. W artykule przedstawiono komputerową metodę realizacji warunku fazowego podczas synchronizacji oraz podano wyniki jej badań symulacyjnych oraz badań na obiektach rzeczywistych.
-
A Set of Low-power Microcontroller-based Modules Used for Testing of Small Energy Measurement Methods
PublicationEstimation of energy consumption of low-power devices is not widely discussed in the scientific literature, but this topic is getting more and more popular. Evaluation process of newly developed methods and instrumentation requires carefull treatment. In order to fulfill this niche, the set of micro-power microcontroller based devices was proposed. The devices represent typical energy consuption profiles and allow experimental verification...
-
Energy storage device based on flywheel, power converters and Simulink real-time
PublicationThis electronic document is a “live” template and already defines the components of your paper [title, text, heads, etc.] in its style sheet. Paper presents information on Energy Storage Device based on Flywheel and bi-directional IGBT Power Converters – designed for LINTE^2 laboratory owned by Gdansk University of Technology in Poland. Paper is divided into four sections. First section of the paper provides introductory information...
-
CUTTING POWER FORECASTING WHILE WOOD SAWING: FRACTURE MECHANICS APPROACH AND AXELSSON’S MODEL COMPARISON
PublicationIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (power) could be considered from a point of view of modern fracture mechanics. Another way is to forecast cutting power consumption on...
-
Development of a spray-ejector condenser for the use in a negative CO2 emission gas power plant
PublicationOne promising solution for developing low-emission power technologies is using gaseous fuel combustion in pure oxygen when the exhaust gas mixture is composed of H2O and CO2, and where CO2 is separated after steam condensation. The paper presents the results of computational analyses providing to the Spray-Ejector Condenser (SEC) development, which is one of the crucial components of the negative CO2 gas power plant (nCO2PP) cycle...
-
Influence of span length and impulse front time on earthing measurement accuracy of power line towers
PublicationThe article discusses the issue of measuring and assessing the features of power line tower earthings using fast-changing waveform. The study analyses the effect of impulse front time and the line span length on errors made during these measurements using impulse meters. It has been found that the assessment conditions similar to the static measurement results occur for the use of 4 μs current impulses and such procedure is useful...
-
Perceived supervisor support as a relevant factor for subordinates’ job satisfaction – model verification
Publication -
The INTERSTROKE Study: hypertension is by far the most important modifiable risk factor for stroke
Publication -
Further evidence that oxidative stress may be a risk factor responsible for the development of atherosclerosis
Publication -
Household standards and socio-economic aspects as a factor determining energy consumption in the city
Publication -
The pH Value as a Factor Modifying Bacterial Colonization of Sinonasal Mucosa in Healthy Persons
Publication -
Modern information technology as a factor supporting participation in physical culture of a contemporary man
Publication -
The Phytoestrogen Genistein Modulates Lysosomal Metabolism and Transcription Factor EB (TFEB) Activation
Publication -
THE INVESTMENT ENVIRONMENT MANAGEMENT SYSTEM IN THE FRAMEWORK OF LEGAL SUPPORT AS A FACTOR OF NATIONAL SAFETY
Publication -
Temperature effect on the current-voltage characteristic fill factor for the silicon solar cells
PublicationW pracy przedstawiono badania wpływu temperatury pracy krzemowych ogniw fotowoltaicznych na wartość współczynnika wypełnienia charakterystyki prądowo- napięciowej (FF). Efekty dyfuzyjne w obszarze złącza oraz rekombinacja nośników ładunku ograniczają wartość współczynnika wypełnienia charakterystyki. Spadek tej wartości wynika głównie ze wzrostu wartości rezystancji szeregowej rs. Na rezystancję szeregową składają się: opór emitera...
-
The formal safety assessment and influence of human factor in application to chosen ship's type
PublicationTragedia jednego ze statków typu ro-ro pokazała podatność tego typu statków na utratę stateczności, przewrócenie się, a w ostateczności zatonięcie. Wszystkie ro-rowce charakteryzują się małym zanurzeniem, a wynurzona część kadłuba podatna jest na działanie wiatru. Jeżeli dodatkowo w takich warunkach dochodzi element nieprawidłowego rozmieszczenia pojazdów i ich słabego zamocowania to groźba przesunięcia ładunku staje się realna....
-
Strength deterioration of 26H2MF and 34HNM steels used in ship engines: hydrogen factor
PublicationBadano podatność stali 26H2MF i 34HNM poddanych różnej obróbce cieplnej na niszczenie wodorowe. Badania wykonano metodą powolnego rozciągania z szybkością 10-6 s-1. Określano wytrzymałość, wydłużenie, przewężenie i energię zniszczenia. Stwierdzono znaczna degradację w 0,01 M kwasie siarkowym z dodatkiem arszeniku. Wykazano istnienie korelacji między obróbką cieplną i stopniem degradacji. Efekty przypisano pułapkowaniu wodoru.
-
High Q-factor Microwave Fabry-Perot Resonator With Distributed Bragg Reflectors
PublicationZrealizowany został rezonator Fabry-Perot pracujący na częstotliwości 39 GHz i wykorzystujący dwie pary ćwierćfalowych kwarcowych reflektorów Bragga. Dla fali o długości 98.26 mm otrzymano dobroć ok. 560,000, co oznacza 4.3-krotny wzrost w porównaniu z identycznym rezonatorem bez reflektorów Bragga. Analizę problemu wykonano przy pomocy metody różnic skończonych w dziedzinie częstotliwości (FDFD) i porównano z uproszczonym rozwiązaniem...
-
Hydrophobic and hydrophilic properties of pollutants as a factor influencing their redistribution during snowpack melt
PublicationGlaciers accumulate organic pollutants delivered by snow. However, our understanding of the exact dynamics of organic pollutants in the snowpack relies primarily on laboratory experiments and mathematical models. To fill the gap related to the detailed field data, we have conducted observations of melting snow profiles in two locations and three different stages of melting on one High Arctic glacier, as well as in superimposed...
-
Polyarmonic model of synchronous generator for analysis of autonomous power generation systems
PublicationAbstract: This paper presents the polyharmonic modelling of synchronous generator (SG) in machine variables. The simple geometry and windings physical layout has been used for inductance calculations of a salient-pole SG. The main advantage of this model is the ease of describing an autonomous power generation system (APGS) in terms of its topology and thus providing effective analysis at the static and dynamic states, both for...