Search
Filters
total: 813
filtered: 718
Search results for: closed crack, closed delamination, nonlinearity, crack detection methods
-
NONLINEAR VIBRATION ANALYSIS OF BEAM AND PLATE WITH CLOSED CRACK: A REVIEW
PublicationThe effect of nonlinearity is high sensitivity in damage detection, especially for closed cracks and delamination. This review illustrates the results of several researchers dealing with nonlinear effects caused by the closure of cracks in the structure, i.e., beam and plate structures. Early detection of damage is an important aspect for the structure and, therefore, continuous progress is being made in developing new and effective...
-
Detection of Closing Crack in Beam Based on Responses Induced by Harmonic Excitation
PublicationThe non-linear contact model was chosen to simulate the closed crack in the cantilever beam. The study examines the shape and characteristics of the phase diagram of a cantilever beam with closed cracks. It investigates how various crack properties influence the geometry of the phase diagram and proposes a method for identifying cracks based on their features. The area of each closed curve in the phase diagram is determined using...
-
Detection and size estimation of crack in plate based on guided wave propagation
PublicationThe paper presents results of the comprehensive theoretical and experimental investigation of crack detection in metallic plate using guided wave propagation. The main aim of the paper is to develop the novel method which would allow for linear crack size estimation with the use of minimal number of the transducers. In general, there exists the relation between length of the propagation path and the wave amplitude value. However,...
-
Crack Detection in Metallic Surfaces Based on Dumbbell-Shaped Defected Ground Structures in Microstrip Technology
PublicationIn this paper, a novel crack detection sensor using a microstrip loaded with a Dumbbell-Shaped Defected Ground Structure (DS-DGS) is proposed. The sensing element is etched in the ground plane of a microstrip line and it is easy to fabricate. The electromagnetic (EM) field of the microstrip couples to the DS-DGS, thus demonstrating a bandstop behavior. It is shown that in the presence of a crack in a metallic surface underneath the...
-
On the crack front curvature in bonded joints
PublicationStandard tests of adhesively bonded specimens are likely to produce heterogeneous stress distribution along the crack front and its vicinity. High separation rate mode I dominated fracture test is performed.Observation of post mortem fractured surfaces with an optical microscope reveals characteristic features of mixed mode I/III fracture near the sides of the specimen but not in the middle. At first, finite elements calculations...
-
Formation and Growth of the Crack in Bonded Joints Under Mode I Fracture: Substrate Deflection at Crack Vicinity
PublicationAdhesive bonding is now commonly used in aircraft, cars, boats, etc. In these applications, thin panels are often bonded. In such thin structures, heterogeneous mechanical loading along the bondline edge (or potential crack front), is likely to arise due to 3D structural effects. The crack front and its vicinity is a special region, in that it is where structural properties of the adherend material meet those of the adhesive (discontinuity)....
-
Hertzian Crack Propagation in Ceramic Rolling Elements
PublicationThe properties of ceramics are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such crack are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations are based on a three dimensional model for the ring crack propagation. The stress intensity factors along crack...
-
Numerical analysis of crack propagation in silicone nitride
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculation...
-
Design of novel highly sensitive sensors for crack detection in metal surfaces: theoretical foundation and experimental validation
PublicationThe application of different types of microwave resonators for sensing cracks in metallic structures has been subject of many studies. While most studies have been focused on improving the sensitivity of planar crack sensors, the theoretical foundation of the topic has not been treated in much detail. The major objective of this study is to perform an exhaustive study of the principles and theoretical foundations for crack sensing...
-
Redevelopment of Russian closed towns: The Example of Zato "Zvezdniy"
PublicationThe current economic crisis is having a strong impact on socio-economic processes in the development of Russian cities. The impact of the crisis is particularly strong on city territory where the activity of core industrial enterprises, military units or similar institutions has been stopped. In such cases, the situation is directly related to the functioning of military units or one industrial enterprise responsible for the formation...
-
Wave propagation in plate structures for crack detection
Publication -
Wave propagation in plate structures for crack detection.
PublicationW pracy przedstawiono analizę propagacji fali poprzecznej w płycie z pęknięciem. Do modelowania zagadnienia zastosowano metodę elementów spektralnych.
-
On stress singularity near the tip of a crack with surface stresses
PublicationIn the framework of the simplified linear Gurtin–Murdoch surface elasticity we discuss a singularity of stresses and displacements in the vicinity of a mode III crack. We show that inhomogeneity in surface elastic properties may significantly affect the solution and to change the order of singularity. We also demonstrate that implicitly or explicitly assumed symmetry of the problem may also lead to changes in solutions. Considering...
-
Open-Set Speaker Identification Using Closed-Set Pretrained Embeddings
PublicationThe paper proposes an approach for extending deep neural networks-based solutions to closed-set speaker identification toward the open-set problem. The idea is built on the characteristics of deep neural networks trained for the classification tasks, where there is a layer consisting of a set of deep features extracted from the analyzed inputs. By extracting this vector and performing anomaly detection against the set of known...
-
Genetic algorithm for fatique crack detection in Timoshenko beam.
PublicationW pracy przedstawiono metodę detekcji peknięć zmęczeniowych w początkowej fazie ich rozwoju. Algorytm detekcji wykorzystuje metodę algorytmów genetycznych połączoną z metodą gradientową. Funkcja celu oparta została o zmiany w propagujacej fali sprężystej.
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements
PublicationThe dataset titled EH36 steel for shipbuilding (plate thicnkness 50mm) - CMOD - force record, a0/W = 0.6 contains CMOD (Crack Mouth Opening Displacement) - Force record which is the base for evaluation of fracture toughness of structural steel. Bend specimens witch Bx2B section (B= 50mm), and relative initial crack length a0 / W = 0.60 were used. The test was carried out at ambient temperature in accordance to ISO 12135 standard....
-
Mesoscopic simulations of crack propagation in concrete using cohesive elements
PublicationThe paper presents results of two-and three-dimensional meso-scale simulations of fracture in notched concrete beams subjected to three-point bending test. Concrete was assumed as a 3-phase material composed of aggregate grains placed in the cement matrix with Interfacial Transitional Zones (ITZs) between then. In 2D simulations macro-voids were also taken into account. The particle distribution was taken from real concrete beams...
-
Ultimate compressive strength assessment of uncleaned and cleaned corroded plates with locked crack
PublicationThe work presented here investigates the structural response of cleaned corroded plates, subjected to compressive load in the presence of a locked crack, where the change of mechanical properties as a result of corrosion development and the cleaning process is also accounted for. A Finite Element model for assessing the compressive strength, considering geometric and material nonlinearities, is developed, and the analysed plates...
-
Distortional buckling of thin-walled columns of closed quadratic cross-section
PublicationThe elastic stability of axially compressed column related to the cross-section distortion is investigated. Two kinds of closed quadratic cross-sections are taken into consideration with internal walls and without it. The governing differential equation is derived with aid of the principle of stationary total potential energy. The critical loads for the simply supported columns are found in an analytical form and compared with...
-
Comments on “Closed Form Variable Fractional Time Delay Using FFT”
PublicationIn this letter drawbacks of the aforementioned paper are pointed out. The proposed approach is improved with minor modifications of the discrete frequency response. This allows for design of fractional delay filters which are close to optimal and can be efficiently implemented in the frequency domain using the sliding DFT based structure. Alternatively, the derived equivalent closed form formulae for offset windows can be used...
-
Analysis of Ceramic Elements with Ring-Crack Defects in Lubricated Rolling Contact
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. Surface ring cracks on lubricating rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations...
-
An image processing approach for fatigue crack identification in cellulose acetate replicas
PublicationThe cellulose acetate replication technique is an important method for studying material fatigue. However, extracting accurate information from pictures of cellulose replicas poses challenges because of distortions and numerous artifacts. This paper presents an image processing procedure for effective fatigue crack identification in plastic replicas. The approach employs thresholding, adaptive Gaussian thresholding, and Otsu binarization...
-
Crack propoagation in MgO-PSZ ceramic materials
PublicationThe properties of ceramic materials such as elevated hardness, high temperature capability, low coefficient of thermal expansion are of interest for rolling element materials. Widely used ceramic materials in engineering applications are silicon nitride, zirconia and alumina. The paper presents an experimental study of the fatigue life of MgO-PSZ ceramic material in lubricated contact with defined types of cracks. A ceramic angular...
-
Design Analysis of Micro Gas Turbines in Closed Cycles
PublicationThe problems faced by designers of micro-turbines are connected with a very small volume flow rate of working media which leads to small blades’ height and high rotor speed. In the case of gas turbines this limitation can be overcome by the application of a closed cycle with very low pressure at the compressor inlet (lower than atmospheric pressure). In this way we may apply a micro gas turbine unit of accepted efficiency to work...
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements Dataset
PublicationThe dataset titled EH36 steel for shipbuilding (plate thickness 50 mm) – CMOD – force record, a0/W=0.6 contains a CMOD (Crack Mouth Opening Displacement) – Force record which is the base for evaluation of the fracture toughness of structural steel. Bend specimens with a Bx2B section (B = 50 mm), and relative initial crack length a0/W=0.60 were used. The test was carried out at ambient temperature in accordance with the ISO 12135...
-
Elastic distortional buckling of thin-walled bars of closed quadratic cross-section
PublicationIn this study a tin-walled bar with closed quadratic cross-section is considered. The elastic stability of axially compressed bar related to the cross-section distortion is investigated. The governing differential equatio is derived with aid of the principle of stationary potential energy. The critical load for simply supported bar is found in an analytical form and it is copared with the FEM solution. Sufficient accuracy of the...
-
Elastic distortional buckling of thin-walled bars of closed quadratic cross-section
PublicationIn this study a thin-walled bar with closed quadratic cross-section is considered. The elastic stability of axially compressed bar related to the cross-section distortion is investigated. The governing differential equation is derived with aid of the principle of stationary total potential energy. The critical load for the simply supported bar is found in analytical form and it is compared with the FEM solution. Sufficient accuracy...
-
Influence of laser processing of the low alloy medium carbon structural steel on the development of the fatigue crack
PublicationThe paper contains the results of the structural analysis, hardness tests and fatigue tests conducted for the medium carbon structural steel with low content of Cr and Ni after its processing with CO2 laser beam. Pre-cracks were made in the round compact tension (RCT) specimen used for fatigue test. Next, four paths, parallel to each other, were melted on both sides of the samples using a laser beam. The paths were perpendicular...
-
Theoretical examination of the fracture behavior of BC3 polycrystalline nanosheets: Effect of crack size and temperature
Publication2D carbon graphene nanostructures are elements of advanced materials and systems. This theoretical survey provides explanation to the mechanical and fracture behavior of mono- and polycrystalline BC3 nanosheets (denoted as MC- and PCBC3NS, respectively) as a function of temperature and the type of crack defects. The mechanical performance of PCBC3NS at elevated temperatures was monitored varying the number of grain boundaries (the...
-
The energy approach to fatigue crack growth of S355 steel welded specimens subjected to bending
PublicationThe study presents the results of the research on the rate of fatigue crack growth subjected to bending in the ferritic-pearlitic structure. The studies were carried out at a constant amplitude of the moment and at various values of the load ratios R and at the operating frequency of the machine of 28.4 Hz. Flat specimens made of S355 steel and with fillet welds and with double-sided blunt external notches as well as concave...
-
Circular saws with closed chip grooves
PublicationW pracy przedstawiono analizę wpływu kształtu rowków wiórowych ostrzy piły tarczowej na sposób odprowadzania wiórów ze strefy skrawania. Zaprezentowano rozwiązanie konstrukcyjne piły tarczowej z domkniętymi rowkami wiórowymi
-
Minimization of the number of periodic points for smooth self-maps of closed simply-connected 4-manifolds
PublicationLet M be a smooth closed simply-connected 4-dimensional manifold, f be a smooth self-map of M with fast grow of Lefschetz numbers and r be a product of different primes. The authors calculate the invariant equal to the minimal number of r-periodic points in the smooth homotopy class of f.
-
Closed-loop stimulation of temporal cortex rescues functional networks and improves memory
PublicationMemory failures are frustrating and often the result of ineffective encoding. One approach to improving memory outcomes is through direct modulation of brain activity with electrical stimulation. Previous efforts, however, have reported inconsistent effects when using open-loop stimulation and often target the hippocampus and medial temporal lobes. Here we use a closed-loop system to monitor and decode neural activity from direct...
-
Instrumented end notched flexure - Crack propagation and process zonemonitoring Part II: Data reduction and experimental
PublicationA mode II instrumented end notched flexure three point bending (ENF) adhesion test is described. The adhesive joint consists of two aluminium alloy (AW7075-T6) plates bonded with a structural epoxy adhesive (Hysol EA 9395™). Strain gauges are attached to the outer surface (backface) of the substrates in the lengthwise direction to measure local surface strain during crack propagation. Simultaneously, load/displacement measurements...
-
The effect of multiaxial geocomposite reinforcement on fatigue performance and crack propagation delay in double-layered asphalt beams
PublicationThe presented study investigates the effect of a recently developed multiaxial geocomposite made of polypropylene geogrid and non-woven fabric on the delay of crack propagation, based on four-point bending tests of large asphalt concrete beams – both for reinforced and non-reinforced specimens. Several approaches are described in this study, including analysis of stiffness modulus decrease and analysis of crack propagation using...
-
Mathematical modeling and prediction of pit to crack transition under cyclic thermal load using artificial neural network
PublicationThe formation of pitting is a major problem in most metals, which is caused by extremely localized corrosion that creates small holes in metal and subsequently, it changes into cracks under mechanical load, thermo-mechanical stress, and corrosion process factors. This research aims to study pit to crack transition phenomenon of steel boiler heat tubes under cyclic thermal load, and mathematical modeling...
-
Prediction of Deflagrative Explosions in Variety of Closed Vessels
Publication -
Application of Closed Circuit Television for Highway Telematics
Publication -
Eine Eeue Technik zur Präzisen Rissfortschrittsmessung im DCB oder im Keilversuch = A novel technique for precise crack length measurement in the DCB or wedge test
PublicationDiverse methods have been tried to study crack length, most basic relying on direct, or microscopic, observation of the crack tip position. Optical correlation, both lasermoiré and speckle interferometry, a single strain gauge and displacement sensorshave also been employed. Crack length measurement is, however, delicate. We present a novel method making use of strain gauges attached to one of the adherends.
-
Influence of pitting corrosion on fatigue and corrosion fatigue of ship and offshore structures. Part II: Load - pit crack interaction
PublicationIn the paper has been discussed influence of stresses on general corrosion rate and corrosion pit nucleation and growth rate, whose presence has been questioned by some authors but accepted by most of them. Influence of pit walls roughness on fatigue life of a plate suffering pit corrosion and presence of so called "non damaging" pits which never lead to initiation of fatigue crack, has been presented. Possibility of prediction...
-
Corrosion fatigue crack propagation rate characteristics for weldable ship and offshore steels with regard to the influence of loading frequency and seawater temperature
PublicationAfter Vosikovsky (1975), the corrosion fatigue crack growth rate (CFCGR) characteristics have been divided into three regions. The region-III rates are very close to mechanical fatigue crack growth rates. CFCGR formulae, including the long-crack length effect (in region I only), the loading frequency effect (in region II only), and the saltwater temperature effect, have been proposed. It has been assumed that CFCGR is proportional...
-
A Closed Bipolar Electrochemical Cell for the Interrogation of BDD Single Particles: Electrochemical Advanced Oxidation
PublicationA closed bipolar electrochemical cell containing two conductive boron-doped diamond (BDD) particles of size 250 – 350 m, produced by high-pressure high-temperature (HPHT) synthesis, has been used to demonstrate the applicability of single BDD particles for electrochemical oxidative degradation of the dye, methylene blue (MB). The cell is fabricated using stereolithography 3D printing and the BDD particles are located at either...
-
Stability Analysis of Shunt Active Power Filter with Predictive Closed-Loop Control of Supply Current
PublicationThis paper presents a shunt active power filter connected to the grid via an LCL coupling circuit with implemented closed‐loop control. The proposed control system allows selective harmonic currents compensation up to the 50th harmonic with the utilization of a model‐based predictive current controller. As the system is fully predictive, it provides high effectiveness of the harmonic reduction, which is proved by waveforms achieved...
-
Instrumented End Notched Flexure - Crack propagation and process zonemonitoring. Part I: Modelling and analysis
PublicationAnalysis of the three-point bending, End Notched Flexure (ENF), test is presented for exploitation with a new experimental methodology using the backface strain monitoring technique. The model consists oftwo Timoshenko beams joined with a two parameter elastic foundation, to evaluate stress and strain fields in both adherends and the adhesive layer, together with the specimen compliance and energyrelease rate. This model is compared...
-
Crack identification in cantilever beam using wavelets
PublicationPrzedstawiono metodę identyfikacji zniszczeń przy użyciu transformacji falkowej. Rozpatrzono przykład belki wspornikowej. Pokazano, że transformacja falkowa wykrywa miejsce zniszczenia.
-
Propagation of in-plane waves in an isotropic panel with a crack
PublicationW pracy przedstawiono model tarczowego elementu spektralnego do analizy propagacji fali wzdłuznej w panelach z uszkodzeniami.
-
The performance of H2O, R134a, SES36, ethanol, and HFE7100 two-phase closed thermosyphons for varying operating parameters and geometry
PublicationIn this study, the influences of different parameters at performance two-phase closed thermosiphon (TPCT) was presented. It has been confirmed that the working fluid, as well as operating parameters and fill ratio, are very important factors in the performance of TPCT. The article shows characteristics of gravitational tube geometr ies, as well as the technical characteristic of the most important system components, i.e., the evaporator/condenser....
-
Numerical investigations of discrete crack propagation in Montevideo splitting test using cohesive elements and real concrete micro-structure
PublicationThe paper is aimed at accurately predicting the discrete fracture process in concrete specimens under complex stress states in two dimensional (2D) simulations. Plain concrete specimens subjected to Montevideo splitting test (MVD) were used for consideration due to non-negligible shear stresses impact in this type of test. In order to reflect the heterogeneous nature of the concrete, the meso-structure of the samples was included...
-
Optical Bubble Microflow Meter for Continuous Measurements in a Closed System
Publication -
Frequency distribution of chemical oscillations in the closed Belousov Zhabotinsky reaction.
PublicationW publikacji przedstawiono wykorzystanie metody STFT (krótkoczasowej transformaty Fouriera) do analizy oscylacji chemicznych. Badano rejestry potencjałowe reakcji Biełousowa Żabotyńskiego. Wykazano niestacjonarność analizowanych przebiegów. Wykazano liniową zależność pomiędzy częstotliwością oscylacji a stężeniem jednego z komponentów reakcji (bromian potasu). Udowodniono przydatność analizy czasowo-częstotliwościowej do analizy...