Search results for: SURFACE QUALITY
-
The evaluation of the surface quality after laser cutting
Publication -
Selected aspects of the surface quality of the wooden elements after planing
PublicationThe quality of the surface of wooden elements, that have been planed, has got a crucial meaning in the whole production process flow, since the obtained effects affect the quality of wooden surface after painting. The emergence of defects in most cases causes need to qualify workpiece as a scrap part or additional work activity must be done. In the paper selected results of the investigation of the effect of the cutting tool wear...
-
Surface quality control of a thin SiN layer by optical measurements
PublicationFiber optic interferometers have a wide range of applications, including biological and chemical measurements. Nevertheless, in the case of a reflective interferometer setup, standard silver mirrors cannot be used in every measurement, due to their chemical activity. This work investigates the surface quality of a thin optical layer of silicon nitride (SiN), which can serve as an alternative material for silver mirrors. We present...
-
Surface quality of the plasma cermet coatings after grind finishing
Publication -
Metrological analysis of surface quality aspects in minimum quantity cooling lubrication
Publication -
Comparison of Surface Quality and Tool-Life of Glulam Window Elements after Planing
PublicationThe quality of the surface of wooden elements, that have been planed, has a crucial importance in the whole production process, since the obtained effects affect the quality of wooden surface after fi nishing (painting). The occurrence of defects is usually the reason for qualifying a workpiece as scrap or for requiring additional work. This paper presents the selected results of research of the effect of the cutting tool wear...
-
Surface quality and topographic inspection of variable compliance part after precise turning
Publication -
Effects of CO2 and Nd:YAG Laser Remelting of the Ti6Al4V Alloy on the Surface Quality and Residual Stresses
PublicationThe titanium alloys are materials susceptible to tribological wear and the laser treatment can be applied in surface treatment processes to obtain for example higher hardness level. From the other side, it is important to take into consideration, that hardness increase that can be connected with cracks . The aim of this research was to investigate the effects of different lasers and the process parameters on the form and level...
-
Bisquare robust polynomial fitting method for dimple distortion minimization in surface quality analysis
Publication -
Innovative Solutions in Surface Water Quality Monitoring
PublicationIn 2010 a project entitled "Integrated Support System for Management and Protection of Water Dam Reservoir (ZiZOZap)” was initiated, to aid solving water management problems on a river and dam reservoir formed on it. An innovative system of continuous monitoring was created, that encompassed selected physical and chemical parameters of river and lake waters in three chosen sites. This article presents a selection of results, that...
-
Determinants of the surface quality, density and dimensional correctness in selective laser melting of the Ti-13Zr-13Nb alloy
PublicationSelective laser melting is widely used for custom-designed elements. Successful manufacturing depends on laser treatment parameters and material features. This research aimed to determine the effects of laser power, scan time and hatch distance on surface quality, relative density and dimensional precision for cuboids made of the Ti-13Zr-13Nb alloy. The influence of energy density, energy flux and pre-heating was seen to be decisive...
-
Types of Surface Impurities versus the Quality of Brazed Joints
PublicationBrazing is one of the primary joining processes increasingly often applied in industry. Because of their mechanical properties, overlap joints are particularly popular when making brazed structures. The use of brazed joints in structures of critical importance requires that particular attention be paid to joint quality, e.g. by the appropriate cleaning of surfaces to be joined. The article presents results of non-destructive tests...
-
The influence of humic substances in treated sewage on the quality of surface waters
PublicationAt present the evaluation of WWTP effectiveness is based upon organic matter and nutrients removal. Recently it was found out that sewage treatment leads to formation of resistant to biochemical degradation organic compounds, similar to humic acids. The humic acids formed during sewage treatment process play diversified functions when discharged to surface waters - for instance they can act as carriers of hydrophobic organic pollutants...
-
The effect of thermal modification on the quality of the milled surface of beech and pine wood
PublicationThe article deals with the effect of thermal modification on the quality of the created surface during milling on CNC milling cutters. The quality of the created surface is evaluated based on surface roughness, specifically its roughness parameter Ra. The observed surface is created by a shank cutter with a diameter of 20 mm and three cutting edges in a spiral at a standard speed of 18,000. min-1. The article compares thermally...
-
Mechanical Properties, Microstructure and Surface Quality of Polypropylene Green Composites as a Function of Sunflower Husk Waste Filler Particle Size and Content
PublicationAgricultural waste is a still untapped source of materials that can, in case of proper utilization, significantly improve the sustainability of polymers and their composites. In this work, polymer composites based on isotactic polypropylene were produced incorporating ground sunflower husk in the amount of 10 wt% and 20 wt%. The work’s main objective is to evaluate how preliminary fractioning of this agricultural waste filler affects...
-
Experimental investigation of selective laser melting parameters for higher surface quality and microhardness properties: taguchi and super ranking concept approaches
Publication -
Surface water quality assessment by the use of combination of multivariate statistical classification and expert information
PublicationThe present study deals with the assessment of surface water quality from an industrial-urban region located in northern Poland near to the city of Gdansk. Concentrations of thirteen chemicals includingtotal polycyclic aromatic hydrocarbons (PAHs), halogenated volatile organic compounds (HVOCs) and major ions in the samples collected at five sampling points during six campaigns were used as variablesthroughout the study. The originality...
-
Methods for quality improvement of multibeam and LiDAR point cloud data in the context of 3D surface reconstruction
PublicationPoint cloud dataset is the transitional data model used in several marine and land remote-sensing applications. During further steps of processing, the transformation of point cloud spatial data to more complex models containing higher order geometric structures like edges and facets may be possible, if an appropriate quality level of input data is provided. Point cloud datasets usually contain a considerable amount of undesirable...
-
Hybrid Processing: the Impact of Mechanical and Surface Thermal Treatment Integration onto the Machine Parts Quality
Publication -
Technological features of forming the quality characteristics of the surface layer during diamond smoothing in the integrated processing
Publication -
THE IMPLICATIONS OF ECONOMIC DEVELOPMENT, CLIMATE CHANGE AND EUROPEAN WATER POLICY ON SURFACE WATER QUALITY THREATS
Publication -
Network design for surface water quality monitoring in a road construction project using Gamma Test theory
PublicationRoad construction has a negative environmental impact on the surrounding aquatic environment, requiring the continuous monitoring of surface water quality. Here, optimization of the water quality monitoring network (WQMN) is an essential step in supporting the sustainable development of road construction projects. This study introduces Gamma Test theory (GTT) as a practical method for optimizing the WQMN of surface waters during...
-
Persistent organic pollutants (POPs) as an indicator of surface water quality in the vicinity of the Polish Polar Station, Horsund
PublicationSurface waters were collected in the vicinity of the Polish Polar Station in Hornsund (Svalbard) to determine their concentration of various persistent organic pollutants (POPs), such as polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs). In addition, parameters such as pH, SEC and TOC were measured. In total, 15 samples of lake water from and 15 samples of stream water were analysed. The sampling took...
-
Integrated Processing: Quality Assurance Procedure of the Surface Layer of Machine Parts during the Manufacturing Step "Diamond Smoothing"
Publication -
Investigating the drinking and surface water quality and associated health risks in a semi-arid multi-industrial metropolis (Faisalabad), Pakistan
Publication -
Groundwater Quality in the Gdansk Aquifer System
PublicationThe Gdańsk hydrogeological system consists of three main aquifers: Cretaceous, Paleogene-Neogene and Pleistocene. Chemical composition of groundwater varies between water-bearing beds, although water from Pleistocene and Paleogene-Neogene aquifers shows much similarities. The dominant hydrochemical groundwater types is HCO3-Ca. This type is characteristic for Pleistocene deposits in the Kashubian Lake District where natural chemical...
-
The effect of an active force while slide diamond burnishing of wooden shafts upon process quality
PublicationThe quality of the surface of wooden elements that have been turned and burnished has got a crucial meaning in the whole production process flow, since the obtained effects affect the quality of the wooden surface after finishing (coating, painting). In the paper, selected results of the investigation of the effect of the burnishing process on the surface quality of the elements after turning are presented. Research experiments...
-
Influence of Honing Parameters on the Quality of the Machined Parts and Innovations in Honing Processes
PublicationThe article presents a literature review dealing with the effect of the honing parameters on the quality of the machined parts, as well as with the recent innovations in honing processes. First, an overview about the honing and the plateau-honing processes is presented, considering the main parameters that can be varied during machining. Then, the influence of the honing parameters on surface finish, shape deviation and material...
-
The microbial and sensory quality of mackerel hot smoked in mild conditions
PublicationThe quality indices of Atlantic mackerel, hot smoked at core temperature not exceeding 60°C, containing 14–27 g salt and 580–670 g water per kg meat, was determined just after smoking and during storage. The aerobic plate count after smoking, chilling and packing in cardboard boxes was 0–12 cfu/25 cm2of the skin of the smoked fish and 10–240 cfu/g of flesh. It was 1.9 log cycle lower than that in the frozen raw material. At 2°C,...
-
Effect of electrode waterproof coating on quality of underwater wet welded joints
PublicationIn this paper, the effects of different hydrophobic coatings on the surface of covered electrodes on the quality of wet welded carbon steel joints were discussed. Commonly available hydrophobic substances used in industrial applications were selected for the research. The aim of using waterproof coatings was to check the possibility to decreasing the susceptibility of highstrength low-alloy S460N steel to cold cracking. During...
-
Polymer based thick films - material quality and interface resistance evaluation
PublicationThe properties of polymer based thick film layers mede using different resistive pastes and dipping silvers have been studied. The composite of carbon and graphite (C/Gr) conducting particles suspended in different polymer vehicles were used for preparation resistive layers. Interface resistance Rc created between dipping silver (DiAg) contact layer and resistive layer was determined from the surface potential distribution measurements...
-
Towards high quality ITO coatings: the impact of nitrogen admixture in HiPIMS discharges
PublicationThe paper reports controlled deposition of optically transparent and electrically conductive ITO films prepared by a combination of rf (13.56 MHz) and High Power Impulse Magnetron Sputtering (HiPIMS) systems without any post deposition thermal treatment/annealing. It is shown that (i) reactive admixture of N2 gas to the process and (ii) pressure in the deposition chamber enable to optimize optical properties of ITO films. Furthermore,...
-
The possibility of the application of a potentiometric sensor with all-solid-state electrodes for the quality control of different natural waters
PublicationThe quality of various natural waters was examined by a new potentiometric sensor with six all solid state electrodes containing an appropriate lipophilic compound in a polymer membrane. Physicochemical parameters such as conductivity and acidity of tested waters were also tested. All waters were neutral or slightly alkaline and contained different ions (e.g., Cl–) due to the place of their sampling (a coastal zone and a moraine...
-
Assessment of River Water Quality and Pollution Status Using Physicochemical and Biometrics, Awetu River, Ethiopia
PublicationThe surface water is contaminated by a variety of synthetic organic and inorganic compounds, chemicals, and nutrients; due to this reason, the quality of the water resources of Ethiopia is declining at an alarming rate, resulting in severe environmental degradation. The main objective of the study was to recognize the pollution status river for the study area by physicochemical parameters and the extent of microbial environmental...
-
Surface texture of pine wood beams after planing in industrial conditions
PublicationMeasuring the surface features of wooden components after planing is connected with the rising demands regarding to the quality of the painted window frames. In the paper the complex surface texture analysis especially identifying of surface damages using non-contact 3D measurement techniques for precise area measurement were presented.This enabled the study of irregular surface features with sufficient fidelity and resolution....
-
The Quick Measure of a Nurbs Surface Curvature for Accurate Triangular Meshing
PublicationNURBS surfaces are the most widely used surfaces for three-dimensional models in CAD/CAE programs. As a model for FEM calculation is prepared with a CAD program it is inevitable to mesh it finally. There are many algorithms for meshing planar regions. Some of them may be used for meshing surfaces but it is necessary to take the curvature of the surface under consideration to avoid poor quality mesh. The mesh must be denser in the...
-
Road surface roughness estimation employing integrated position and acceleration sensor
PublicationAssessment of a surface quality being an essential task for the authorities supervising the roads provides the subject of the paper. Information about riding quality of a pavement, important for drivers, both in terms of their comfort and safety is collected during experiments employing mobile sensors. The paper describes the use of a miniature position and acceleration sensor for evaluation of the roughness of the road surface....
-
Modelling the impact of the agricultural holdings and land-use structure on the quality of inland and coastal waters with an innovative and interdisciplinary toolkit
PublicationThe changes taking place in the marine coastal zones are extremely important, as about 40% of the human population currently lives in the coastal areas (within 100 kilometres of the coastline) increasing anthropogenic pressure on the marine ecosystems. Agriculture is a significant source of nutrients to the marine environment that increase hypoxia, eutrophication and may pose a threat to the services provided by ecosystems. In...
-
Microbial and chemical quality assessment of the small rivers entering the South Baltic. Part I: Case study on the watercourses in the Baltic Sea catchment area
PublicationThe area of the Coastal Landscape Park (CLP) due to its location is extremely attractive touristic area. In the summer season, a significant increase in population density is observed, which influences surface water quality. Large numbers of tourists generate an increased amount of municipal wastewater, being treated in local treatment plants and discharged into rivers and streams. The paper presents preliminary research from summer...
-
Quality control of cheese samples for the presence of natamycin preservative – A natural deep eutectic solvent (NADES) based extraction coupled with HPLC
PublicationA new protocol for the determination of natamycin – an antifungal agent used as a food preservative - in cheese samples – is described. This new method is based on a natural deep eutectic solvent (NADES) green extraction procedure. High-performance liquid chromatography (HPLC) was used for detection and quantification. NADESs with different molar ratios were evaluated for efficient and selective extraction. NADES made of thymol...
-
The Effect of Steaming Beech, Birch and Maple Woods on Qualitative Indicators of the Surface
PublicationThis work presents the effect of steaming beech, birch and maple woods on the resulting quality of the milled wood surface. The steaming process of the studied woods results in a targeted change in the color of the wood, which changes from the original light white-gray color to fine reddishbrown to dark brown color shades that are more or less saturated depending on the temperature of the saturated water steam. The color changes...
-
Tuber Quality
Publication -
Analysis of the Surface Stereometry of Alloyed Austenitic Steel after Fibre Laser Cutting using Confocal Microscopy
PublicationThe paper extends the concept of cut edge quality and examines the fibre laser cutting process. A Prima Power Platino Fiber Evo device with a reference speed (RS) of 3500 mm/min was used for laser cutting. In order to analyse the influence of the laser cutting speed on the cut edge quality of X5CrNi18-10 stainless steel sheets, macroscopic studies were conducted on a stereoscopic microscope and surface stereometry on a confocal...
-
Treated wasetewater as a source of humic substances in surface waters
PublicationHumic substances impose substantial effect on the aquatic environment as well as the water organisms and human health. Among other features, the humic acids determine organoleptic properties of surface waters. Therefore explanation of the origin and properties of humic acids in surface waters is one of the priorities of water technology.Recently it was pointed out that in the wastewater treatment process organic compounds characterized...
-
Surface Texture after Turning for Various Workpiece Rigidities
PublicationIn the paper, we present an analysis of the surface texture of turned parts with L/D (length/diameter) ratios of 6 and 12 and various rigidity values. The studies were carried out on samples made of S355JR steel and AISI 304 stainless steel. A detailed analysis of 2D surface profiles was carried out by using a large number of parameters that allowed us to distinguish significant differences in the surface microgeometry, which confirmed...
-
Quality Assurance and Quality Control in the Analytical Chemical Laboratory: A Practical Approach.
PublicationNowe opracowanie książkowe z zakresu QA/QC to praktyczny podręcznik zarówno dla studentów jak i pracowników laboratoriów. Opisano systemu jakości wyników pomiarów analitycznych i poszczególnych jego składników: spójności pomiarowej, niepewności pomiaru, walidacji procedury analitycznej, materiałów odniesienia i badań międzylaboratoryjnych. Opisano i przedstawiono narzędzia statystyczne służące do obliczania parametrów walidacyjnych,...
-
Chemometric Evaluation of WWTPs’ Wastewaters and Receiving Surface Waters in Bulgaria
PublicationWastewater treatment plant (WWTP) installations are designed and operated to reduce the quantity of pollutants emitted to surface waters receiving treated wastewaters. In this work, we used classical instrumental studies (to determine chemicals and parameters under obligations put with Directive 91/271/EEC), ecotoxicological tools (Sinapis alba root growth inhibition (SA-RG) and Heterocypris incongruens mortality (MORT) and growth...
-
Role of surface recombination in perovskite solar cells at the interface of HTL/CH3NH3PbI3
PublicationIn order to achieve the highest performance of organometal trihalide perovskite solar cells, it is required to recognize the dominant mechanisms which play a key role in a perovskite material. In the following studies, we have focused on the interfacial recombination between the hole transporting layer (HTL) and the perovskite CH3NH3PbI3 in solar cell devices with p–i–n architecture. It has been shown that Cu:NiOx : used as HTL...
-
Quality of analytical results
PublicationW pracy przedstawiono podstawowe informacje dotyczące kontroli i zapewnienia jakości wyników analitycznych (QC/QA). W postaci odpowiednich schematów zaprezentowano: ideę spójności pomiarowej; zasady walidacji metodyk analitycznych; rolę materiałów odniesienia w procesie analitycznym.
-
Water and food quality
PublicationRozdział zawiera opis podstawowych właściwości fizykochemicznych wody, rolęwody jako składnika żywności, wymagania odnośnie wody stosowanej w przemyśleżywnościowym, charakterystykę wody odpadowej, ścieków i ich neutralizację.