Search results for: SIMULATION STUDY
-
Pin Angle Thermal Effects on Friction Stir Welding of AA5058 Aluminum Alloy: CFD Simulation and Experimental Validation
PublicationThe friction stir welding (FSW) of tool pin geometry plays a critical role in the final properties of the produced joint. The tool pin geometry directly affects the generation of heat and the flow of internal materials during the FSW process. The effects of the FSW tool pin angle on heat generation and internal flow have not been quantitatively investigated in detail. In this manuscript, a validated Computational Fluid Dynamic...
-
Recent advances in rapid multiobjective optimization of expensive simulation models in microwave and antenna engineering by Pareto front exploration
PublicationPractical engineering design problems are inherently multiobjective, that is, require simultaneous control of several (and often conflicting) criteria. In many situations, genuine multiobjective optimization is required to acquire comprehensive information about the system of interest. The most popular solution techniques are populationbased metaheuristics, however, they are not practical for handling expensive electromagnetic...
-
Comparison of the exponential thermal transient parameterization methods with the SMTP method in the unipedicled DIEP flap computer modelling and simulation
PublicationThe aim of this paper is to compare the spatial contrast of the image descriptors obtained via three different thermal transient parameterization methods in Active Dynamic Thermography. The thermal constants and amplitude values of the one- and two- exponential parametrization are compared to the Simplified Magnitude-Temporal Parametrization method (SMTP). The comparison is performed using the data obtained by simulating the cold...
-
The experimental evaluation and modeling of SBR removing nutrients under varied aeration conditions
PublicationSequencing batch reactors (SBR) are mainly characterized by sequential process phases of fill, react, settle, decant and idle periods that allow considerable flexibility in the design and operation in different conditions. This flexibility and the unique features of SBRs used to wastewater treatment by activated sludge systems operated in laboratory scale, allow not only conducting experiments for the standard conditions but also...
-
Electrical Tree Growth Behavior Under AC and DC High Voltage in Power Cables
PublicationThis work investigates the impact of an applied AC and DC high voltage on the electrical tree behavior in extruded cross-linked polyethylene (XLPE) insulation based on simulation and experimental validation. Extensive partial discharge (PD) testing methods are being implemented for high voltage cables under AC voltage for monitoring their condition. However, these PD testing methods cannot be utilized for power cables under DC...
-
Diaryl Sulfide Derivatives as Potential Iron Corrosion Inhibitors: A Computational Study
PublicationThe present work aimed to assess six diaryl sulfide derivatives as potential corrosion inhibitors. These derivatives were compared with dapsone (4,4′-diaminodiphenyl sulfone), a common leprosy antibiotic that has been shown to resist the corrosion of mild steel in acidic media with a corrosion efficiency exceeding 90%. Since all the studied compounds possess a common molecular backbone (diphenyl sulfide), dapsone was taken as the...
-
On analog comparators for CMOS digital pixel applications. A comparative study
PublicationVoltage comparator is the only – apart from the light-to-voltage converter – analog component in the digital CMOS pixel. In this work, the influence of the analog comparator nonidealities on the performance of the digital pixel has been investigated. In particular, two versions of the digital pixel have been designed in 0.35 μm CMOS technology, each using a different type of analog comparator. The properties of both versions have...
-
Study of data scheduling methods in the WiMAX Mobile metropolitan area networks
PublicationThe paper discusses basic assumptions of the WiMAX Mobile system. It also presents and analyses the results of simulation tests run for selected data scheduling methods and subcarrier allocation. Based on the test results, the authors have prepared a comparative analysis of two popular data scheduling methods, i.e. WRR and PF, and their own method CDFQ which uses information about the current channel situation for the queuing processes...
-
Numerical Study of the Impinging Jets Formed by an Injector with Different Nozzle Diameters
PublicationThe collision of two or more liquid jets may provide considerable atomisation and efficient mixing of injected substances at the same time. This phenomenon is used, among others, in rocket engines, where the fuel and oxidiser are introduced separately and almost immediately mixed through self-impingement. Depending on the injection and operating conditions, diverse configurations of impinging jets are used, such as doublets,...
-
Separation of the effects of notch and macro residual stress on the MFL signal characteristics
PublicationMagnetic flux leakage (MFL) distribution for three configurations of samples has been investigated in order to study the influence of notch and plastic deformation separately as well as together. Samples have been made of S355 steel. The MFL signal measurements were carried out along the longest dimension of the sample over a length of 120 mm. Two components of magnetic field were measured: 1) tangential to the main axis and 2)...
-
ASYNCHRONICZNE METODY RADIOLOKALIZACYJNE
PublicationW pracy przedstawiono wybrane problemy lokalizowania obiektów w asynchronicznych sieciach radiowych. W pierwszej kolejności zostały zdefiniowane kryteria jakościowe do oceny efektywności pracy opracowanych metod oraz przedstawiono model symulacyjny, który został użyty do badań. W kolejnych trzech rozdziałach szczegółowo opisano trzy oryginalne asynchroniczne metody radiolokalizacyjne w różnych wariantach. Przeprowadzono analizę...
-
<title>Decomposition of MATLAB script for FPGA implementation of real time simulation algorithms for LLRF system in European XFEL</title>
Publication -
A Simulation-Optimization Model for Automated Parcel Lockers Network Design in Urban Scenarios in Pamplona (Spain), Zakopane, and Krakow (Poland)
Publication -
Comparison of Miller laryngoscope and UEScope videolaryngoscope for endotracheal intubation in four pediatric airway scenarios: a randomized, crossover simulation trial
Publication -
Influence of gas turbine controller adjustment on propulsion system behaviour in high sea conditions. Part 2. The simulation investigations.
PublicationDo badań przyjęto układ napędowy okrętowy z turbinami gazowymi napędzającymi poprzez przekładnię mechaniczną zębatą śrubę okrętową o zmiennym skoku.Przy użyciu programu komputerowego Matlab i jego nakładki Simulink wykonano symulację dynamiki układu napędowego statku pracującego na wzburzonym morzu.Zbadano wpływ nastaw i typu regulatora na pracę układu. Porównano nastawy układu regulacyjnego układu napędowego dla pracy...
-
Tailoring optical constants of few-layer black phosphorus coatings: Spectroscopic ellipsometry approach supported by ab-initio simulation
Publication2D black phosphorus (BP) has attracted extensive attention as an anisotropic platform for novel optoelectronic and polarizing optics applications. Insight into the factors that tune the optical and polarizing properties of 2D BP reveals their essential influence on BP-based photonic and optoelectronic devices. In this work, studies of the optical constants of few-layer black phosphorus coatings are studied and discussed, with particular...
-
Sano-Tachiya-Noolandi-Hong, Onsager and Braun models vs Monte Carlo simulation of charge photogeneration in organic solids
PublicationThe Sano-Tachiya-Noolandi-Hong (STNH), Onsager, and Braun models as well as Monte Carlo (MC) simulations of charge recombination/separation have been applied for the first time to reproduce the results of the electromodulated photoluminescence measurements in vacuum-evaporated films of fluorescent materials commonly used in optoelectronic devices. The values of the electron-hole pair final recombination speed in the monomer emitters:...
-
An Attempt to Develop a Model Selection Algorithm of Computer Simulation during the Design Process of Mechanical Response of Any Mechanical Body
PublicationIn the literature, there are algorithms associated with the design of simulations of technological processes, in which the material model has always been defined previously. However, in none of the studies of computer simulation modelling of technological processes known to the authors of this article, is there a detailed description of how the algorithm, or the selection of plastic model used, is subject to this process. This...
-
An attempt to develop a model selection algorithm of computer simulation during the design process of mechanical response of any mechanical body
Publicationn the literature, there are algorithms associated with the design of simulations of technological processes, in which the material model has always been defined previously. However, in none of the studies of computer simulation modelling of technological processes known to the authors of this article, is there a detailed description of how the algorithm, or the selection of plastic model used, is subject to this process. This article...
-
Efficient Surrogate Modeling and Design Optimization of Compact Integrated On-Chip Inductors Based on Multi-Fidelity EM Simulation Models
PublicationHigh-performance and small-size on-chip inductors play a critical role in contemporary radio-frequency integrated circuits. This work presents a reliable surrogate modeling technique combining low-fidelity EM simulation models, response surface approximations based on kriging interpolation, and space mapping technology. The reported method is useful for the development of broadband and highly accurate data-driven models of integrated...
-
Phase I and phase II metabolism simulation of antitumor-active 2-hydroxyacridinone with electrochemistry coupled on-line with mass spectrometry.
PublicationHere, we report the metabolic profile and the results of associated metabolic studies of 2-hydroxyacridinone (2-OH-AC), the reference compound for antitumor-active imidazo- and triazoloacridinones. Electrochemistry coupled with mass spectrometry was applied to simulate the general oxidative metabolism of 2-OH-AC for the first time. The reactivity of 2-OH-AC products to biomolecules was also examined. The usefulness of the electrochemistry...
-
Hybrid stepless distribution transformer with four-quadrant AC/DC/AC converter at low voltage side - simulation tests
PublicationThe article presents the work of the stepless hybrid distribution transformer (HT), as an alternative to the so far applied Automatic Voltage Regulator (AVR) solutions, used to control the voltage in the power system in terms of the fundamental harmonic. The HT is a combination of a conventional distribution transformer and an AC/DC/AC converter connected in series with the transformers secondary winding. In the work the basic...
-
Rapid design optimization of antennas using variable-fidelity EM models and adjoint sensitivities
PublicationPurpose – Development of techniques for expedited design optimization of complex and numerically expensive electromagnetic (EM) simulation models of antenna structures validated both numerically and experimentally. The paper aims to discuss these issues. Design/methodology/approach – The optimization task is performed using a technique that combines gradient search with adjoint sensitivities, trust region framework, as well as...
-
Air journal bearing utilizing near-field acoustic levitation: stationary shaft case
PublicationResults of a study to examine a unique idea of self-levitating journal bearing are presented in this paper. the idea represents a radical departure from the current bearing technology. it utilisesacoustic levitation, which relies on the sound energy radiated by an object supporting a load. acoustic levitation has been demonstrated to support loads of up to 10 kg. in order to support a load theacoustic wave emitted by the radiating...
-
Assessing Acute Toxicity and Endocrine Disruption Potential of Selected Packages Internal Layers Extracts
PublicationThe focus of the present study is migration of toxic substances from food contact materials and its actual influence on the health of the final consumer. Two food packagings (metal cans, TetraPack®) and five simulants medias (water, ethanol, acetic acid, DMSO, artificial saliva) were selected for simulation studies. For assessment of acute toxicity and endocrine disruption potential of extract samples, two biotests (Microtox® and...
-
Implementation of the FOPID Algorithm in the PLC Controller - PWR Thermal Power Control Case Study
PublicationIn the paper authors describe proposition of design and verification procedures of the discrete Fractional Order PID (FOPID) algorithm for control of the Pressurized Water Reactor (PWR) thermal power near its nominal operating point. The FOPID algorithm synthesis consists of: off-line optimal tunning of its parameters in continuous time-domain with LQ (Linear Quadratic) performance index and simplified models of nuclear reactor...
-
Numerical Study of Turbulent Flow and Heat Transfer of Nanofluids in Pipes
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (Reynolds number between 6000 and 12000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Traffic Type Influence on QoS Network Performance of Streaming Traffic Class
PublicationFeasibility study on QoS routing proved that the traffic type influence the network performance. The performance is defined here as a number of packets serviced by the network. In the paper additional element - buffers lengths used in service system was verified in terms of dependencies with routing performance. We present results obtained by simulation for many simulation scenarios. Analysis was done for two different network...
-
Recent advances in traffic optimisation: systematic literature review of modern models, methods and algorithms
PublicationOver the past few decades, the increasing number of vehicles and imperfect road traffic management have been sources of congestion in cities and reasons for deteriorating health of its inhabitants. With the help of computer simulations, transport engineers optimise and improve the capacity of city streets. However, with an enormous number of possible simulation types, it is difficult to grasp valuable, innovative solutions which...
-
Numerical study of turbulent flow and heat transfer of nanofluids in pipes
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (6 000 < Re < 12 000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data of Vajjha et al. [1]. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
A case study of robust sliding mode control applied to inverted pendulum on a cart
PublicationA control problem of an inverted pendulum on a cart has been addressed in this paper. In particular, a synthesis of alternative sliding mode control for stabilisation of an inverted pendulum at an upper equilibrium point has been investigated. Hence, the feasibility of implementing the developed control system, taking into account primarily the friction of the cart against the gantry and the limited length of the gantry, in a real...
-
Voltage and frequency regulation of a standalone induction generator by reduced-rating power electronic compensators - comparative evaluation
PublicationIn this paper are considered two fundamental topologies of power electronic compensators for voltage and frequency control of a standalone self-excited induction generator (IG) system. These are voltage and current source inverter based shunt compensators with energy storage. The aim of this study is to assess main features of both topologies in dynamic and steady-state IG operation. The whole system is modelled with the aid of...
-
Quasi-discrete modelling of PMSM phase currents in drives with low switching-to-fundamental frequency ratio
PublicationThis study proposes a new quasi-discrete approach to modelling the permanent magnet synchronous motor (PMSM). The quasi-discrete modelling reflects the impact of continuous rotor movement, which takes place during a control cycle, on the shape of motor current waveforms. This provides much improvement in current modelling accuracy under inverter low switching-to-fundamental frequency operation. The proposed approach may be used...
-
COMPARISON OF NOISE EMISSION OF HCT AND CLASSIC VEHICLE COMBINATIONS FOR TIMBER TRANSPORTATION IN SWEDEN
PublicationBy means of a special simulation tool, the noise emission of a high-capacity heavy vehicle (11 axles) was compared to that of a classic heavy vehicle (a truck-dolly-semitrailer with 8 axles). The two cases are designated “Extended vehicle” versus “Classic vehicle” in this study, having total lengths of 34 and 25 m, respectively. The Classic vehicle represents the most common articulated heavy vehicle configuration for transport...
-
Continuous blood pressure monitoring by photoplethysmography - signal preprocessing requirements based on blood flow modelling
PublicationObjective. The aim of the study is to investigate the effect of the signal sampling frequency and low-pass filtering on the accuracy of the localisation of the fiducial points of the photoplethysmographic signal (PPG), and thus on the estimation of the blood pressure (i.e. the accuracy of the estimation). Approach. Statistical analysis was performed on 3,799 data samples taken from a publicly available database. Four PPGfiducial...
-
On deterministic procedures for low-cost multi-objective design optimization of miniaturized impedance matching transformers
PublicationPurpose This paper aims to investigate deterministic strategies for low-cost multi-objective design optimization of compact microwave structures, specifically, impedance matching transformers. The considered methods involve surrogate modeling techniques and variable-fidelity electromagnetic (EM) simulations. In contrary to majority of conventional approaches, they do not rely on population-based metaheuristics, which permit lowering...
-
Tackling Air Pollution in Cities with Modelling and Simulation: Remote Group Model Building as an Educational Tool Supporting System Dynamics Modelling
Publication -
Non-linear circuit model of a single doubly-fed induction machine formulated in natural axes for drive systems simulation purposes
PublicationMathematical modelling and a circuit model formulated in natural axes of a single doubly-fed induction machine, with the account of magnetic circuit nonlinearity are presented in the paper. Derivation of the model differential equations was based on Lagrange's energy method. State functions of magnetic elements in the model are non-linear and depend on all currents flowing in the machine windings and on the angle of rotor position....
-
FEM Analysis of Multi Storied RC Structure using (E-TAB simulation ) and Need of High rise structures in Developing Countries
Publication -
Characteristics of hydration water around hen egg lysozyme as the protein model in aqueous solution. FTIR spectroscopy and molecular dynamics simulation
PublicationW niniejszej pracy przedstawiono wyniki badań dotyczące hydratacji białka modelowego - lizozymu z jaja kurzego w roztworze wodnym. Wiodącą techniką stosowaną w badaniach była spektroskopia oscylacyjna FTIR z zastosowaniem techniki rozcieńczenia izotopowego wody półciężkiej HDO w roztworze wody zwykłej. Analiza widma HDO przy pomocy "metody widm zaburzonych" pozwoliła na wyizolowanie widma wody zaburzonej przez lizozym, a tym samym...
-
Cementless controlled low-strength material (CLSM) based on waste glass powder and hydrated lime: Synthesis, characterization and thermodynamic simulation
Publication -
A Dynamic Forecast Demand Scenario Analysis to Design an Automated Parcel Lockers Network in Pamplona (Spain) Using a Simulation-Optimization Model
Publication -
Nonlinear harmonic amplitudes in air coils above and below a metal plate as a function of tensile strength via finite element simulation.
PublicationOpisano wyniki obliczeń numerycznych (symulacja metodą MES) wpływu naprężeń na amplitudy nieliniowych harmonicznych napięcia indukowanego w cewkach powietrznych umieszczonych nad i pod płytą.
-
Influence of gas turbine controller adjustment on ship propulsion system behaviour in rough sea conditions. Part 2. The simulation investigations.
PublicationPrzedstawiono model dynamiki układu napędowego okrętowego, wykorzystując metodę elementów skończonych. Układ napędowy składa się z dwóch turbin gazowych napędzających poprzez przekładnię mechaniczną zębatą pędnik o nastawnym skoku. W symulacji układu napędowego zadawano wymuszenia wartością zadaną nastaw prędkości na regulatorze oraz wymuszenia od falowania morza w zależności od stanu morza. Przedstawiono wyniki takich symulacji.
-
Modelling of sequencing batch reactor operating at various aeration modes
PublicationThe presented study involved designing a computer model of a sequencing batch reactor (SBR) at laboratory scale. The data pertaining to the technical aspects of the bioreactor and quality indicators of wastewater constituted the input for the employed simulation tool, i.e. GPS-X software package. The results of a simulation involving a 12-hour operation cycle are presented in this work; each cycle included 6 phases: filling, mixing,...
-
Trees as a Shading System for Streets on the East–West Axis: Computer Simulations for the Selected Geometrical Proportions of Building Developments in Humid Continental Climate
PublicationThe study is aimed at investigating the possibilities for solar protection provided to the street canyon located on the E–W axis and with the following profiles: shallow (height/width (H/W) = 0.2, 0.6, and 1) and deep (H/W = 2) by two rows of trees located at a distance of 3 m away from southern and northern façades. The research was based on numerical simulation analyses conducted in the Rhinoceros® program, with the application...
-
Accuracy improvement of the prestressed concrete structures precise geometry assessment by use of bubble micro-sampling algorithm
PublicationPrestressed concrete structures are well-known technology for a vast period, but nevertheless, this very technology is a leading solution, currently used in construction industry. Prestressed concrete structures have a huge advantage over conventional methods because it uses the properties of concrete in a very efficient way. The main idea behind this technology is to introduce into the cross-section of the structure, the internal...
-
Nonlinear fuzzy control of the dissolved oxygen in activated sludge processes
PublicationWastewater treatment plant is generally a complex, multivariable, time varying and nonlinear large scale industrial system. Moreover, interactions between the components are very strong. The dissolved oxygen tracking problem is one of the most complex and fundamental issues of biological processes. Air for the aerated tanks is supplied by aeration system (blowers, pipes, diffusers). It is a complex dynamic system. The new control...
-
Possible effects of the 1984 St. Clair River ice jam on bed changes
PublicationThis study examines the possible effect of the record ice jam of 1984 in the St. Clair River on river bed changes and conveyance. Numerical simulations were made to examine the flow and bed shear stresses during the jam formation and release periods. Simulation results indicate that the ice jam in the river did not cause a significant increase in bed shear stress compared to pre- and post-jam open water conditions. The insignificant...
-
Respiration rate estimation using non-linear observers in application to wastewater treatment plant
PublicationA problem of respiration rate estimation using two new non-linear observers for a wastewater treatment plant is addressed in this paper. In particular, a non-linear adaptive Luenberger-like observer and a super twisting sliding mode observer have been derived to produce stable and bounded estimates of the respiration rate. During the synthesis of the particular observer, an appropriate mathematical utility model was used. The observability...