Search results for: SHAFT RADIAL VIBRATIONS
-
Reduction of vibrations of steel structure models with Polymeric Bearings - experimental study
PublicationEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Therefore, designing earthquake protective systems has become an extremely challenging problem in civil engineering. Base isolation is one of the most popular and widely adopted methods of protecting structures against earthquake forces. The present paper reports the results obtained from the shaking table experimental...
-
Analysis of Failures of High Speed Shaft Bearing System in a Wind Turbine
PublicationDuring the operation of wind turbines with gearbox of traditional configuration, consisting of one planetary stage and two helical stages high failure rate of high speed shaft bearings is observed. Such a high failures frequency is not reflected in the results of standard calculations of bearing durability. Most probably it can be attributed to atypical failure mechanism. The authors studied problems in 1.5 MW wind turbines of...
-
Rigid finite elements and multibody modelling used in estimation and reduction of rod vibrations
PublicationIn the paper, a mechanical set composed of a robot (manipulator) and of an elastic beam is considered. The beam is fixed to the top of the robot structure. In most of the similar cases, undesired vibrations can be excited in the beam. They are especially significant, when dynamics in the robot braking period is examined. In the paper, estimation and modification of length of the braking period is proposed, in order to reduce the...
-
ATTEMPT AT EVALUATING THE INFLUENCE OF BENDING STRESS ON SHAFT WEAR PROCESSES IN WATER LUBRICATED SLIDING BEARING WITH A RUBBER BUSHING
PublicationWater lubricated bearings find increasingly wide application in shipbuilding or hydro–power industry, the popularity stemming from their numerous advantages. Unfortunately, as it turns out, water lubricated bearings do not always meet expectations, as on occasion they become subject to intense, premature wear which requires costly repair. One of the still unexplained phenomena is the process of excessive bearing wear, in particular...
-
Measurement file of stainless stell shaft LSS1 and LSS2 with diameter 95,995 with 3d measurment device
Open Research Data3d point cloud consist of measured points on new stainless steel shaft used during testing hydrodynamic journal PEEK bearing.
-
Forced vibrations in a dynamic system that is damped by a mechanism that trans-pass through its singular position
PublicationIn the paper, vibrations of a hybrid multibody-continuous system are investigated. For all the mechanical devices, effective damping methods are crucial in the design process. To obtain it, installation of viscous dampers or elasto-viscous elements is dominant. In the paper, an alternative method is investigated. It is based on modal disparity. To describe the method briefly, when structural damping is present in continuous systems,...
-
Minimization of vibrations during milling of flexible structures using mechatronic design techniques
PublicationThe paper presents an innovative effective method of minimizing vibrations during milling of flexible structures, using a new vibration suppression method based on a workpiece holder with adjustable support stiffness. The proposed method is rooted in mechatronic design techniques, which can become a standard procedure for optimizing the milling process.
-
Sliding friction of alumina (Al2O3) with friction induced vibrations
Open Research DataTest files containing data on experiments in self mated sliding contact of alumina Al2O3 lubricated with either water or paraffin oil. Tests run in variable load/velocity conditions and with different dynamic settings of the test rig (PT-3 tribometer). The aim of the research was to attempt in finding correlations between the dynamic characteristics...
-
Gas Detection Using Resistive Gas Sensors And Radial Basis Function Neural Networks
PublicationWe present a use of Radial Basis Function (RBF) neural networks and Fluctuation Enhanced Sensing (FES) method in gas detection system utilizing a prototype resistive WO3 gas sensing layer with gold nanoparticles. We investigated accuracy of gas detection for three different preprocessing methods: no preprocessing, Principal Component Analysis (PCA) and wavelet transformation. Low frequency noise voltage observed in resistive gas...
-
Assessment of radial run-out of circular saw.
PublicationW pracy przedstawiono ocenę bicia promieniowego pił tarczowych na podstawie analizy zróżnicowania przekrojów warstw skrawanych przez poszczególne ostrza piły
-
The inverse problem in a hyperbolic section radial compressor.
PublicationNa przykładzie wirnika sprężarki porównano wyniki rozwiązania zadania odwrotnego w ramach modelu 2D prowadzącego do kształtu wirnika, z zadaniem prostym, w ramach modelu 3D, dla skonstruowanego wirnika na bazie modelu 2D.Zasadniczym celem było uzyskanie równomiernych (bez oderwań) pól parametrów w obrębie wirnika sprężarki. Pokazano jak zmiana obrysu wirnika, z klasycznego kształtu stożkowego na hiperboliczny, wpłynąć może na...
-
ENERGY ANALYSIS OF THE PROPULSION SHAFT FATIGUE PROCESS IN A ROTATING MECHANICAL SYSTEM PART III DIMENSIONAL ANALYSIS
PublicationThis article presents the third and last part of the problem of diagnosing the fatigue of marine propulsion shafts in terms of energy with the use of the action function, undertaken by the authors. Even the most perfect physical models of real objects, observed under laboratory conditions and developed based on the results of their research, cannot be useful in diagnostics without properly transferring the obtained results to the...
-
Numerical estimation of the pile toe and shaft unit resistances during the installation process in sands
PublicationNumerical simulations of a pile jacking were carried out. A Coupled Eulerian–Lagrangian (CEL) formulation was used to treat with large deformation problems. An Abaqus, a commercial Finite Element Method software suit, was used as a computing environment. The Mohr–Coulomb constitutive model was applied and the Coulomb model of friction was used to describe pile-soil interaction. Calculations were made for three different pile diameters....
-
EVALUATING THE INFLUENCE OF BENDING STRESS ON A 1H18N9 STEEL SHAFT WEAR PROCESS IN A WATER LUBRICATED SLIDING BEARING WITH A RUBBER BUSHING
PublicationThe issue of excessive wear of shaft journals co-working with a rubber bearing has been unexplained so far. Premature and sometimes very intensive wear of ship sliding bearings in water conditions is the reason for carry out very expensive and more frequent than expected repairs. The authors (E. Piątkowska, W. Litwin) made an attempt to find a case that influences the value of this wear described in the paper “Attempt at Evaluating...
-
Experimental ORC micro-power plant for CHP application Part B: Radial and Multi-stage axial turbines
PublicationThe co-generative micro-power plant with the HFE7100 applied as a working medium was designed and built for experimental investigations. Special attention is paid to a micro-turbine which was built and tested in two variants: a radial turbine and an axial turbine. A concept of a radial turbine with 2 centripetal and 2 centrifugal stages is shown. This prototype was equipped with an aerostatic gas bearing and, alternatively, with...
-
The Possibilities of Improving the Fatigue Durabilityof the Ship Propeller Shaft by Burnishing Process
PublicationHeavily loaded structural elements operating in a corrosive environment are usuallyquickly destroyed. An example of such an element is a ship propeller operating in a seawaterenvironment. This research presents a fatigue resistance test performed on elements operating inseawater. Different processing parameters applied on the samples in particular were compared withthe specimens whose surface had been burnished differently and...
-
Problems of Flaking in Strengthening Shaft Burnishing
PublicationThe article presents the results of testing the surface condition of shafts manufactured by a strengthening rolling burnishing process. The shafts with a hardness about 220 HB were burnished with a roller with different force. Researches were carried out with particular attention to the structure of the outflowing material in the tool zone during burnishing process. The article presents the results of the examinations of burnished...
-
Prediction of Pile Shaft Capacity in Tension Based on Some Direct CPT Methods—Vistula Marshland Test Site
PublicationThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with diameter 0.4 m and the length varied from 8 m to 14.6 m were subjected to static load tests in tension. Their...
-
Polymeric Bearings as a new base isolation system suitable for mitigating machine-induced vibrations
PublicationThe present paper summarizes the preliminary results of the experimental shaking table investigation conducted in order to verify the effectiveness of a new base isolation system consisting of Polymeric Bearings in reducing strong horizontal machine-induced vibrations. Polymeric Bearing considered in the present study is a prototype base isolation system, which was constructed with the use of a specially prepared flexible polymer...
-
Prediction of pile shaft capacity in tension based on some direct CPT methods – Vistula Marshland test site
PublicationThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with a diameter of 0.4 m and the length...
-
The Idea of Using Bayesian Networks in Forecasting Impact of Traffic-Induced Vibrations Transmitted through the Ground on Residential Buildings
PublicationTraffic–induced vibrations may constitute a considerable load to buildings. In this paper, vibrations transmitted through the ground caused by wheeled vehicles are considered. This phenomenon may cause cracking of plaster, cracks in load-bearing elements or even, in extreme cases, collapse of the whole structure. Measurements of vibrations of real structures are costly and laborious. Therefore, the aim of the present paper is to...
-
WATER LUBRICATED MAIN SHAFT BEARINGS - MODERN SOLUTION FOR HYDROPOWER INDUSTRY - Experimental and theoretical studies
PublicationWater-lubricated bearings are finding increasingly wide use in various branches of industry. As such, they may also be encountered in hydro power industry. They are also increasingly frequently employed in bearing systems of marine shaft propulsions and water pumps [1]. This rising popularity is due to a number of reasons [2]. First of all, their simple construction has direct impact on the level of pricing which is usually quite...
-
An optimal form of the finite element mass matrix in the analysis of longitudinal vibrations of rods
PublicationIn this paper, an attempt is made to find the optimal form of the mass matrix of a rod finite element, which allows one to obtain the smallest errors in the longitudinal frequency determination of natural vibrations of any boundary conditions within the whole range of determined frequencies. It is assumed that the mass matrix can be treated as a linear combination of the consistent and diagonal matrices. Based on analytical considerations,...
-
Electromagnetic forced vibrations of composite nanoplates using nonlocal strain gradient theory
PublicationThis article is intended to analyze forced vibrations of a piezoelectric-piezomagnetic ceramic nanoplate by a new refined shear deformation plate theory in conjunction with higher-order nonlocal strain gradient theory. As both stress nonlocality and strain gradient size-dependent effects are taken into account using the higher-order nonlocal strain gradient theory, the governing equations of the composite nanoplate are formulated....
-
Marine propeller shaft bearings under low-speed conditions: water vs. oil lubrication
PublicationThe bearings used in shipbuilding, hydropower, and water pumps have undergone a metamorphosis in recent decades. Because of environmental regulations, lubrication with grease or mineral oil is prohibited. Thus, the standard solutions include water-lubricated bearings with polymer bushings or sealed systems lubricated with oil. When properly designed, assembled, and operated, bearings can operate reliably for years. However, specific...
-
Modes of vibrations occuring in the washboarding phenomenon
PublicationW oparciu o współczesną literaturę oraz wyniki badań własnych przedstawiono teorie zjawiska washboarding dla obróbki na pilarkach taśmowych z użyciem wąskich i szerokich pił. Zaprezentowano również wytłumaczenie wspomnianego zjawiska dla przypadku obróbki na pilarkach ramowych. Poprzez analogię do drgań typu chatter (drgania samowzbudne w obróbce metali) zaproponowano nazwy regenerative washboarding, dla drgań samowzbudnych na...
-
The analysis of mechanical vibrations with use of the MATHCAD.
PublicationPrzedstawiono zagadnienie analizy drgań mechanicznych ze wspomaganiem komputerowym za pomocą programu MATHCAD. Omówiono zagadnienia zastosowania programu w edukacji i w obliczeniach inżynierskich.
-
Modelling of vibrations of a liquid filled tank
PublicationPrzeprowadzono analizę teoretyczną i numeryczną zbiorników długich i krótkich wypełnionych całkowicie lub częściowo cieczą. Wyznaczenie obciążeń hydrodynamicznych dotyczy bezpośrednio wytrzymałości konstrukcji samego zbiornika, a przez to pozwala określić wytrzymałość konstrukcyjną całego kadłuba. Szczególne wymagania stawiane są zbiornikom do przewozu cieczy radioaktywnych, gdyż należy zapewnić bardzo wysoki stopień bezpieczeństwa...
-
Circular saw vibrations or dynamics of the spindle
PublicationSawing of wood with circular saws is a typical example of cutting with multi-blade tools. In that kind of cutting, theposition accuracy of following tool blades is a crucial factor which affects the cutting process and machining final effects.Position tooth errors may cause deterioration in cutting conditions, changes in loads of individual teeth and the tool as a whole,and also a decrease in accuracy and surface quality after...
-
Failure analysis of a high-speed induction machine driven by a SiC-inverter and operating on a common shaft with a high-speed generator
PublicationDue to ongoing research work, a prototype test rig for testing high-speed motors/generators has been developed. Its design is quite unique as the two high- speed machines share a single shaft with no support bearings between them. A very high maximum operating speed, up to 80,000 rpm, was required. Because of the need to minimise vibration during operation at very high rotational speeds, rolling bearings were used. To eliminate...
-
Experimental and numerical study on polymer element used for reduction of temporary steel grandstand vibrations
PublicationThe purpose of the paper is to analyse the effectiveness of a polymer damper in reduction of a temporary steel grandstand vibrations through the experimental and numerical study. The damper considered in the investigation is constructed out of two L-shape steel members bonded with polymer mass of high damping properties. The element has been installed as a diagonal one at the back part of the structure. The method has been compared...
-
Preliminary results from HEDGEHOG REXUS Project - sounding rocket experiment on accelerations, vibrations and heat flow
PublicationAs access to space conditions becomes more available, both technically and economically, scientists' interest in launching finer and more sophisticated experiments grows. This applies now more than ever to fragile by nature biological and chemical experiments. To be qualified for launch, such experiments need to be carefully tested prior to the event. The tests should represent actual launch conditions as closely and in as detailed...
-
Allowable values of radial runout of circular saw blade teeth
PublicationW pracy przedstawiono graniczne wartości bicia promieniowego ostrzy pił na podstawie zaproponowanych kryteriów.
-
Analysis of radial run-out of circular saw's cutting blades
PublicationW pracy przedstawiono analizę bicia promieniowego ostrzy pił tarczowych w procesie przecinania drewna. Analizę przeprowadzono na podstawie zróżnicowania grubości warstw skrawanych przez poszczególne ostrza piły. Dla przykładowej piły, zaprezentowano wyniki obliczeń przebiegów grubości warstw skrawanych przez poszczególne ostrza i grubości całkowitej warstwy skrawanej dla całej piły.
-
Mesh-free approach to Helmholtz equation on radial basis functions
PublicationMetoda radialnych funkcji bazowych (RBF) jest coraz czesciej stosowana przy rozwiazywaniu rownan rozniczkowych czastkowych oraz zagadnien wlasnych. W szczegolnosci znalazla ona zastosowanie w problemach elektrodynamiki obliczeniowej. W publikacji zastosowano RBF do rozwiazania rownania Helmholtza. Wprowadzono nowy algorytm - adaptacyjny do wyznaczania centrow interpolacyjnych. Przedstawiona metode zastosowano do wyznaczenia rozkladow...
-
WATER LUBRICATED MAIN SHAFT BEAR INGS WITH THREE LAYER BUSH – MODERN SOLUTION FOR MARINE INDUSTRY
PublicationWater lubricated sliding bearings are increasingly popular in marine and hydro power industry. Such popularity is partly due to their simple construction which also means a relatively affordable price. Properly designed and installed water lubricated bearings may well last for over a decade. During the last decade their traditional range has been expanded with new, modern products like three layer bearing bush. The work presents...
-
TWO-SHAFT GAS TURBINE TEACHING AND TESTING STATION
PublicationThe station was established as part of a project co-financed by the European Union with the funds of the European Regional Development Fund as part of the Infrastructure and Environment Operational Programme titled: “Establishment of state-of-the-art technical infrastructure for the Engineers of the Future learning programme at the Gdańsk University of Technology” executed in 2013-2015.
-
Sawing accuracy on the twin shaft multi-rip saw
PublicationW pracy przedstawiono analizę i wyniki badań doświadczalnych dokładności przecinania na dwuwrzecionowej pilarce tarczowej. Zaprezentowano warianty struktury geometryczno-ruchowej dwuwrzecionowej pilarki tarczowej, jak również warunki pracy dolnych górnych pił pilarki.
-
Analysis of ship shaft line coupling bolts failure
PublicationW artykule przedstawiono dane statystyczne dotyczące uszkodzeń linii wałów okrętowych, w tym także pęknięć zmęczeniowych śrub sprzęgieł kołnierzowych wałów. Wyjaśniono także mechanizm powstawania tego typu uszkodzeń i zagrożenia jakie niosą ze sobą. Opisano przypadki takich uszkodzeń oraz badania jakie są prowadzone dla lepszego poznania zjawisk zmęczeniowych w omawianych uszkodzeniach.
-
Raman scattering tensors for translational vibrations of ice
Publication -
Viscoplastic analysis of damped vibrations of circular plate
PublicationGłównym celem artykułu jest przedstawienie procedury do nieliniowej statycznej i dynamicznej analizy MES z lepkoplastycznym prawem Bodnera-Partoma. Przedstawione są podstawowe równania modelu konstytutywnego wraz z koncepcją implementacji do komercyjnego programu MSC.Marc przy użyciu procedury UVSCPL. Przedstawiono przykład analizy numerycznej płyty kołowej, zweryfikowany eksperymentalnie. Dodatkowo przedstawiono koncepcje wyznaczania...
-
Friction induced vibrations in sliding of monolithic alumina
PublicationPrzedstawiono wyniki badań wzbudzania się (i ewentualnie - zaniku) drgań mechanicznych towarzyszących tarciu ślizgowemu próbek o płaskiej powierzchni styku, wykonanych z monolitycznego tlenku aluminium. Badano wpływ wymuszeń tribologicznych oraz dynamicznych cech układu badawczego na przebieg zjawiska.
-
Reduction of steel chimney vibrations with a pendlum damper.
PublicationKarman vortices observed around chimneys may induce dangerous structural vi-brations at certain wind velocities. The aim of this paper is to analyse theeffectiveness of pendulum damper in vibration reduction of a steel chimney. A two degree-of-freedom system is used to model the behaviour of the struc-ture equipped with a damper. The results of the study show that the use of pendulum with tuned frequency leads to significant...
-
Chladni and circular saw disc vibrations visualisation
PublicationIn this paper are described some methods for saw disc vibration monitoring in march of time (chronology). Ernst Chaldni, the father of sound visualisation and his patternsis are mentioned. In the last partof article are introduced results received with authors measuring systems.
-
Mesh-free approach to Helmholtz equation based on radial basis functions.
PublicationW artykule zastosowano metodę radialnych funkcji bazowych do rozwiązania równania Helmholthza oraz zaproponowano nowy (adaptacyjny) algorytm wyznaczania centrów interpolacyjnych. W oparciu o prezentowany schemat wyznaczono długości fal odcięcia dla różnych kształtów przekrojów poprzecznych falowodów cylindrycznych.
-
Nonlinear free and forced vibrations of a dielectric elastomer-based microcantilever for atomic force microscopy
PublicationThe majority of atomic force microcode (AFM) probes work based on piezoelectric actuation. However, some undesirable phenomena such as creep and hysteresis may appear in the piezoelectric actuators that limit their applications. This paper proposes a novel AFM probe based on dielectric elastomer actuators (DEAs). The DE is modeled via the use of a hyperelastic Cosserat model. Size effects and geometric nonlinearity are included...
-
Preliminary results from HEDGEHOG REXUS project – A sounding rocket experiment on accelerations, vibrations and heat flow
PublicationDuring flight, a sounding rocket is subject to a unique environment - severe vibrations and substantial heat flux. In order to design payloads, precise measurement of these conditions is required. This paper presents preliminary results from HEDGEHOG REXUS Project, whose scientific goal was to characterise the thermal and dynamic environment of REXUS sounding rockets. For this purpose, two new sensors have been designed - mechanical...
-
Nonlinear Free and Forced Vibrations of a Hyperelastic Micro/Nanobeam Considering Strain Stiffening Effect
PublicationIn recent years, the static and dynamic response of micro/nanobeams made of hyperelasticity materials received great attention. In the majority of studies in this area, the strain-stiffing effect that plays a major role in many hyperelastic materials has not been investigated deeply. Moreover, the influence of the size effect and large rotation for such a beam that is important for the large deformation was not addressed. This...
-
THE INFLUENCE OF HOUSING ARRANGEMENT AND INTERFERENCE ON PRELOAD AND THEORETICAL LIFETIME OF A SYSTEM OF TAPER ROLLER BEARINGS OF A HIGH SPEED SHAFT OF A WIND TURBINE GEARBOX
PublicationA system of two taper roller bearings can carry loads with a high ratio of axial load to radial load. Such a system was proposed for a wind turbine gearbox following the poor durability of original bearing design with the aim of increasing durability. Because of size limits, a proposed system is composed of two different taper roller bearings. Standard manufacturers’ catalogues do not provide information on recommended preload...
-
Scale effect in shaft friction from direct shear tests
PublicationPrzeanalizowano wartości maksymalne tarcia uzyskane w aparacie bezpośredniego ścinania w kontakcie konstrukcja-grunt dla piasków kwarcowych i węglanowych oraz gładkiego i szorstkiego kontaktu. Badania przeprowadzono przy regulowanej sztywności normalnej kontaktu, przy różnej składowej normalnej naprężenia w kontakcie i różnym zagęszczeniu gruntu. Określono efekt skali jako stosunek wartości tarcia mobilizowanego na modelu do tarcia...