Search
Filters
total: 64
Search results for: CURING BEHAVIOR
-
Curing behavior of epoxy/Fe 3 O 4 nanocomposites: A comparison between the effects of bare Fe 3 O 4 , Fe 3 O 4 /SiO 2 /chitosan and Fe 3 O 4 /SiO 2 /chitosan/imide/phenylalanine-modified nanofillers
PublicationIn this study, Fe3O4 magnetic nanoparticles (MNPs) were synthesized (B-MNP) and then modified with SiO2 to form Fe3O4/SiO2 core/shell MNPs. The Fe3O4/SiO2 MNPs were chemically functionalized with chitosan so as to gain Fe3O4/SiO2/Chitosan (CH-MNP). The CH-MNP was functionalized with a macromolecule containing imide and phenylalanine precursors to gain Fe3O4/SiO2/Chitosan/imide/phenylalanine based MNPs (CH-IM-MNP). The differences...
-
Acid-aided epoxy-amine curing reaction as reflected in epoxy/Fe3O4 nanocomposites: Chemistry, mechanism, and fracture behavior
PublicationThis work seeks to answer the question whether or not the presence of acid functional groups accelerate epoxyamine curing reaction. Epoxy/Fe3O4 nanocomposite was considered as a case, where discussions are based on chemistry, mechanism behind curing reactions and fracture behavior influenced by acid assistance to crosslinking. Fe3O4 magnetic nanoparticles (MNPs) with nanosilica decorative layer (B-MNP) were synthesized and subsequently...
-
Curing characteristics of ground tire rubber modified by commercial additives
Open Research DataThe presented results show the influence of commercially available bitumen and transoctenamer rubber (TOR) on the curing behavior of GTR treated by a peroxide. Samples were prepared using a two-roll mill– all in the same manner. After 24 hours of aging at ambient conditions, they were submitted to the curing analysis via Rheometer Monsanto 100S. The...
-
The long-term properties of mineral-cement-emulsion mixtures
PublicationThis publication presents evaluation of long-term behavior of mineral-cement-emulsion (MCE) mixtures. MCE mixtures are among the major products of cold recycling of old asphalt pavements. They are composed by binding of the old materials reclaimed from the pavement and new mineral aggregate using two different binding agents – cement and bituminous emulsion. While bituminous emulsion dissolutes and binds materials quite fast, it...
-
Curing epoxy with ethylenediaminetetraacetic acid (EDTA) surface-functionalized Co Fe3-O4 magnetic nanoparticles
PublicationIn this work, the bulk and surface composition of Fe3O4 supermagnetic nanoparticles were modified for efficient epoxy curing. The bare, ethylenediaminetetraacetic acid (EDTA) capped, and cobalt (Co)-doped EDTA capped Fe3O4 nanoparticles were synthesized electrochemically. The crystalline structure and phase information, surface capping, morphology and magnetization behavior of nanoparticles were studied by X-Ray diffraction (XRD),...
-
GTR/NBR/Silica Composites Performance Properties as a Function of Curing System: Sulfur versus Peroxides
PublicationIn this work, conventional sulfur and two types of organic peroxides (dicumyl peroxide (DCP) and di-(2-tert-butyl-peroxyisopropyl)-benzene (BIB)) curing systems were used to investigate the possibility for tailoring of the performance properties of GTR/NBR blends reinforced with a variable content of highly dispersive silica (0–30 phr). The curing characteristics, static mechanical and acoustical properties, swelling behavior,...
-
Investigating the Impact of Curing System on Structure-Property Relationship of Natural Rubber Modified with Brewery By-Product and Ground Tire Rubber
PublicationThe application of wastes as a filler/reinforcement phase in polymers is a new strategy to modify the performance properties and reduce the price of biocomposites. The use of these fillers, coming from agricultural waste (cellulose/lignocellulose-based fillers) and waste rubbers, constitutes a method for the management of post-consumer waste. In this paper, highly-filled biocomposites based on natural rubber (NR) and ground tire...
-
Curing epoxy with electrochemically synthesized Zn Fe3-O4 magnetic nanoparticles
PublicationCathodic electrodeposition (CED) was applied in synthesis of undoped and zinc (Zn) doped Fe3O4 nanoparticles. Changes in the lattice structure of nanoparticles were monitored using X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM) supported by dispersive X-ray spectrometry (EDS), and vibrating sample magnetometry (VSM). Detailed analyses explored the formation of ZnxFe3–xO4 nanoparticles with x ≈ 0.1,...
-
An attempt to mechanistically explain the viscoelastic behavior of transparent epoxy/starch-modified ZnO nanocomposite coatings
PublicationThe effects of bare and starch-modified ZnO (ZnO-St) nanoparticles on viscoelastic and mechanical properties are studied by dynamic mechanical and tensile analyses. Transparent epoxy-based nanocomposite films are prepared by incorporating bare or starch-modified ZnO particles into the epoxy matrix. The results demonstrated that ZnO particles hindered the curing reactions and hence the final properties of the cured epoxy. As a result,...
-
Injectable poloxamer/graphene oxide hydrogels with well‐controlled mechanical and rheological properties
PublicationAlthough significant progress has been made in the design and application of injectable hydrogels for biomedical applications, concurrent control of rheological and mechanical properties of injectable hydrogels has remained as an open challenge to the researchers. In this work, we introduce and put into practice a photo‐curable poloxamer (also known as Pluronic)/graphene oxide (Plu/GO) injectable hydrogel with well‐controlled rheological...
-
Processing, physico-mechanical and thermal properties of reclaimed GTR and NBR/reclaimed GTR blends as function of various additives
PublicationIn this work, ground tire rubber (GTR) was mechano-chemically reclaimed in the presence of bitumen and various additives. During studies three types of processing and curing additives: (i) peptizer P300; (ii) vulcanization accelerator tetramethylthiuram disulfide (TMTD) and (iii) organic peroxide di(2-tert-butyl-peroxyisopropyl)benzene (BIB1) were applied to enhance reclaiming of GTR. Reclaiming process was evaluated by oscillating...
-
Diagnostics and monitoring of the longest span extradosed bridge in Europe
PublicationThe article presents complex diagnostic procedures applied for the purpose of behavior analysis of the extradosed bridge with the longest span in Europe that was built in 2018 in Poland. The system of health monitoring was used to: register internal forces in temporary supports, monitor concrete bonding, perform in situ diagnostics and operation tests. The bridge is a continuous four-span structure with spans theoretical lengths...
-
Effect of Surface Treatment of Halloysite Nanotubes (HNTs) on the Kinetics of Epoxy Resin Cure with Amines
PublicationThe epoxy/clay nanocomposites have been extensively considered over years because of their low cost and excellent performance. Halloysite nanotubes (HNTs) are unique 1D natural nanofillers with a hollow tubular shape and high aspect ratio. To tackle poor dispersion of the pristine halloysite (P-HNT) in the epoxy matrix, alkali surface-treated HNT (A-HNT) and epoxy silane functionalized HNT (F-HNT) were developed and cured with...
-
Curing epoxy resin with anhydride in the presence of halloysite nanotubes: the contradictory effects of filler concentration
PublicationEpoxy resins can be cured with a wide variety of curing agents such as amines and anhydrides, but anhydride curing would be more favorable for research purpose because of epoxy-anhydride curing taking place slowly at room temperature. Incorporation of natural nanosized minerals into epoxy is of environmental importance. Halloysite nanotubes (HNTs) display chemical properties similar to those of silica and alumina, and hydroxyl...
-
Epoxy/Ionic Liquid-Modified Mica Nanocomposites: Network Formation–Network Degradation Correlation
PublicationWe synthesized pristine mica (Mica) and N-octadecyl-N’-octadecyl imidazolium iodide (IM) modified mica (Mica-IM), characterized it, and applied it at 0.1–5.0 wt.% loading to prepare epoxy nanocomposites. Dynamic differential scanning calorimetry (DSC) was carried out for the analysis of the cure potential and kinetics of epoxy/Mica and epoxy/Mica-IM curing reaction with amine curing agents at low loading of 0.1 wt.% to avoid particle...
-
Preparation and characterization of natural rubber composites highly filled with brewers' spent grain/ground tire rubber hybrid reinforcement
PublicationBrewers' spent grain (BSG) and ground tire rubber (GTR) were applied as low-cost hybrid reinforcement natural rubber (NR). The impact of BSG/GTR ratio (in range: 100/0, 75/25, 50/50, 25/75 and 0/100 phr) on processing and performance properties of highly filled natural rubber composites was evaluated by oscillating disc rheometer, Fourier-transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy,...
-
Monitoring of crosslinking of a DGEBA-PAMAM adhesive in composite/aluminium bonded joint using mechanical and ultra-sound techniques
PublicationAdhesive cure is an important and determining aspect of strength and stability of bonded structures. Crosslinking of the polymer leads to the adhesive strength, stiffness and durability. Depending on the resin and curing agent used, cure time can vary from minutes to weeks, even then 100% crosslinking not being guaranteed. Standard methods based on dynamic mechanical analysis (DMA) or calorimetric techniques (DSC, DTA) are valuable...
-
Monitoring the curing process of epoxy adhesive using ultrasound and Lamb wave dispersion curves
PublicationMonitoring the stiffness of adhesives is a crucial issue when considering the durability andstrength of adhesive joints. While there are many studies conducted on specimens madeonly from adhesive, the problem of curing of an adhesive film in real joints is moderatelyconsidered. This paper presents the monitoring of stiffening of epoxy adhesive using ultra-sound. Ultrasonic pulse velocity method was firstly applied for monitoring...
-
Influence of Actual Curing Conditions on Mechanical Properties of Concrete in Bridge Superstructures
PublicationThis article presents the research on the mechanical characteristics of concrete in the construction of three concrete bridges. A system of recording the internal temperature of concrete and automatic control of laboratory ovens was used for specimen curing. This allowed the specimens to be cured under conditions similar to those occurring in the structure. Before the construction, reference blocks were used to define similar curing...
-
Styrene-Butadiene Rubber/Modified Ground Tire Rubber Blends Co-Vulcanization: Effect of Accelerator Type
PublicationGround tire rubber was thermo-mechanically modified with using a co-rotating twin screw extruder. Modification of GTR was conducted in autothermal conditions. Styrene-butadiene rubber and modified ground tire rubber blends were prepared via two-roll milling. Obtained compounds were cured with conventional system (sulfur/vulcanization accelerator ratio was 2:1). During this research three commonly vulcanization accelerators (MBT,...
-
Reactive Sintering of Ground Tire Rubber (GTR) Modified by a Trans-Polyoctenamer Rubber and Curing Additives
PublicationThe proposed method of ground tire rubber (GTR) utilization involves the application of trans-polyoctenamer rubber (TOR), a commercially available waste rubber modifier. The idea was to investigate the influence of various curing additives (sulfur, N-cyclohexyl-2-benzothiazole sulfenamide (CBS), dibenzothiazole disulfide (MBTS) and di-(2-ethyl)hexylphosphorylpolysulfide (SDT)) on curing characteristics, physico-mechanical, thermal,...
-
The estimation of total volatile organic compounds emissions generated from peroxide cured natural rubber/polycaprolactone blends
PublicationNatural rubber (NR)/polycaprolactone (PCL) blends at the ratio of 90/10% wt. (NR/PCL90/10) and 70/30% wt. (NR/PCL70/30), with a constant amount of dicumyl peroxide, were prepared by compounding in an internal mixer. Obtained NR/PCL bio-based blends were cured at three different temperatures (150 °C, 160 °C and 170 °C). The total content of volatile organic compounds (TVOC) as a function of the NR/PCL blends ratio, and their curing...
-
Kinetics of Cross-Linking Reaction of Epoxy Resin with Hydroxyapatite-Functionalized Layered Double Hydroxides
PublicationThe cure kinetics analysis of thermoset polymer composites gives useful information about their properties. In this work, two types of layered double hydroxide (LDH) consisting of Mg2+ and Zn2+ as divalent metal ions and CO32− as an anion intercalating agent were synthesized and functionalized with hydroxyapatite (HA) to make a potential thermal resistant nanocomposite. The curing potential of the synthesized nanoplatelets in the...
-
Evaluation of the stiffness modulus and phase angle of cold in-place recycled mix-tures for long curing periods
PublicationArticle presents the changes inbehaviour of cold-in place recycling mixtures made using cement and bituminous emulsion (CIR mixtures) after anelongated time of curing. Most of the available literatureregarding change instiffness modulus and phase angle presents resultsfor a maximum of several dozen days,which makesit difficult to predict the behaviour over the whole life of the compacted layer. The article...
-
Monitoring of concrete curing in extradosed bridge supported by numerical simulation
PublicationThe paper describes a mathematical model of concrete curing taking into account kinetics of setting reactions. The numerical model is implemented in the author’s program that was used to monitor thermal effects recorded in the concrete bottom plate of the extradosed bridge. Numerical approach was verified by experimental measurements and used for assessment of the current compressive strength due to degree of hydration of fresh...
-
Epoxy Composites Filled with Natural Calcium Carbonate. 1. Epoxy Composites Obtained in the Presence of Monoperoxy Derivative of Epidian-6 Epoxy Resin
PublicationPhysico-mechanical properties of the products based on filled epoxy-oligomeric mixtures composed of Epidian-5 epoxy resin, oligoesteracrylate TGM-3 and monoperoxide derivative of Epidian-6 epoxy resin (PO) have been investigated. CaCO3 was used as a filler and polyethylene polyamine was a curing agent. The effect of PO and CaCO3 on the gel-fraction content and physico-mechanical properties was examined. Using a scanning electron...
-
Comparative Study of the Mechanical Behaviour of Bitumen- and Cement-Dominated Mixtures with Reclaimed Asphalt
PublicationThe bitumen emulsion-based recycling is a commonly used maintenance treatment in the rehabilitation of low-and medium-volume roads in Europe. Nevertheless, the wide range of climatic conditions across the continent resulted in the variety of mixture concepts and the requirements being adopted for various local conditions. In this regard, the most commonly used parameter to distinguish between the main mixture concepts is bitumen...
-
Numerical simulation of hardening of concrete plate
PublicationThe paper presents a theoretical formulation of concrete curing in order to predict temperature evolution and strength development. The model of heat flow is based on a well-known Fourier equation. The numerical solution is implemented by means of the Finite Difference Method. In order to verify the model, the in situ temperature measurements at the top plate of a road bridge were carried out. A high agreement between numerical...
-
Kinetics of cross-linking processes of fast-curing polyurethane system
PublicationThis work focuses on the application of thermal analysis and kinetics investigations to analyze chemical processes during cross-linking of the complex fast-curing polyurethane system. Non-isothermal Differential Scanning Calorimetry (DSC) measurements were performed for both stoichiometric mixtures of polyol and isocyanate component and for mixture with large isocyanate excess. Isoconversional methods were used to calculate initial...
-
Preliminary Investigation on Auto-Thermal Extrusion of Ground Tire Rubber
PublicationGround tire rubber (GTR) was processed using an auto-thermal extrusion as a prerequisite to green reclaiming of waste rubbers. The reclaimed GTR underwent a series of tests: thermogravimetric analysis combined with Fourier-transform infrared spectroscopy (TGA-FTIR), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), and static headspace and gas chromatography-mass spectrometry (SHS-GC-MS) in order...
-
Isothermal Vulcanization and Non-Isothermal Degradation Kinetics of XNBR/Epoxy/XNBR-g-Halloysite Nanotubes (HNT) Nanocomposites
PublicationThe effect of several concentrations of carboxylated nitrile butadiene rubber (XNBR) functionalized halloysite nanotubes (XHNTs) on the vulcanization and degradation kinetics of XNBR/epoxy compounds were evaluated using experimental and theoretical methods. The isothermal vulcanization kinetics were studied at various temperatures by rheometry and differential scanning calorimetry (DSC). The results obtained indicated that the...
-
Micro‑ and nano‑ bentonite to improve the strength of clayey sand as a nano soil‑improvement technique
PublicationNano-additives results in the formation of nano-cementation (NC). This process is recently used to improve the durability of various building materials. NC used to improve the strength of untreated soil materials, also known as nano soil-improvement (NSI). In few years, the role of nano-additives in various types of soils were developed. In this research, the role of micro- and nano- size of bentonite as soil stabilizer was evaluated...
-
Laboratory assessment of permeability of sand and biopolymer mixtures
PublicationLaboratory assessment of permeability of sand and biopolymer mixtures. This research presents a method of creating seepage barriers in a sandy soil using biopolymer additives (biosubstance), which consist of polysaccharides and water. Polysaccharides strongly interact with water to produce a viscous suspension. The paper aims to investigate the infl uence of a biosubstance employed in a highly permeable sandy soil. Amount of the...
-
Novel Approaches of Using of Spirulina Platensis in Natural Rubber Based Composites
PublicationThe aim of this work was to investigate the influence of Spirulina (Spirulina platensis) as a natural filler on the curing characterization, morphology and mechanical, thermomechanical and thermal properties of natural rubber (NR) based composites. Spirulina was introduced into NR mixture in amount of 0 phr, 10 phr and 30 phr. The vulcanization process was carried out at the determined process condition by using hydraulic press...
-
The Influence of Cement Type on Early Properties of Cold In-Place Recycled Mixtures
PublicationCold in-place recycling is a commonly used maintenance treatment in rehabilitation of low and medium volume roads in Poland. Typically, two types of binding agents are used—cement and bituminous emulsion (or foamed bitumen).Due to the harsh Polish climate with many freeze/thaw cycles and frequent occurrence of saturated conditions, the used amounts of cement are higher than those commonly used in warmer parts of Europe. While there...
-
Isothermal Calorimetry and Compressive Strength Tests of Mortar Specimens for Determination of Apparent Activation Energy
PublicationThe hydration process of cementitious materials involves a thermally activated reaction that depends on the composition of the mixture and the curing temperature. The main parameter affecting the temperature variation of cast-in-place concrete is the apparent activation energy, which can be used for the efficient prediction of the temperature evolution and maturity index of hardening concrete. This paper discusses two methods to...
-
Polyurethanes
PublicationHandbook of Thermoset Plastics, Fourth Edition provides complete coverage of the chemical processes, manufacturing techniques and design properties of each polymer, along with its applications. This new edition has been expanded to include the latest developments in the field, with new chapters on radiation curing, biological adhesives, vitrimers, and 3D printing. This detailed handbook considers the practical implications of using...
-
Synthesis, Structure and Properties of Poly(ester-Urethane-Urea)s Synthesized Using Biobased Diamine
PublicationModern polymer science and technology is focused on the development of partial or fully green polymers. This focus is related to green chemistry trends, which propose using natural and renewable resources as monomers in the synthesis of polymers. In this study, biobased diamine was used as a chain extender of ester-urethane prepolymer. Obtained poly(ester-urethane-urea) contains 16 wt% of biobased diamine. There is mention of an...
-
Thermo-mechanical reclaiming of ground tire rubber via extrusion at low temperature: Efficiency and limits
PublicationThermomechanical reclaiming of ground tire rubber (GTR) was performed at different temperatures (60, 120, and 180°C) using a co-rotating twin-screw extruder. Obtained samples were used in styrene-butadiene rubber (SBR) blends. As reference samples, SBR compounds containing untreated GTR were used. Curing characteristics, static and dynamic mechanical properties, and morphology of the obtained blends were determined. The results...
-
Hydraulic conductivity of a biopolymer treated sand
PublicationThis paper presents results of laboratory assessment of creating seepage barriers in a sandy soil using biopolymer additives (bio substance), which consist of polysaccharides and water. Polysaccharides strongly interact with water to produce a viscous suspension. The aim of the conducted work was to investigate the influence of a biosubstance employed in a highly permeable sandy soil. The amount of the biopolymer used in a sample...
-
Implant system for treatment of the orbital floor defects of blowout fractures in the maxillofacial region using polypropylene yarn and bioactive bone cement
PublicationFractures in the craniofacial region are a serious problem in terms of treatment. The most reasonable solution is the use of individual implants dedicated to a specific patient. The aim of this study was to develop the implant system specifically for treatment of the orbital floor defects of blowout fractures of maxillofacial region, using polypropylene yarn and bone cement. Three types of bone cement were used to fix the polypropylene...
-
Cure kinetics of epoxy/MWCNTs nanocomposites: Isothermal calorimetric and rheological analyses
PublicationA combinatorial route has been applied in cure kinetics study of epoxy nanocomposites containing multi-walled carbon nanotubes (MWCNTs) based on differential scanning calorimetry and rheokinetic analyses under isothermal conditions. Pristine and amine-modified MWCNTs bearing primary and secondary amines were used at very low concentrations (0.1 and 0.3 wt.% based on epoxy weight). Model-free and model-fitting methods were applied...
-
A Comprehensive Review of Phytonutrients as a Dietary Therapy for Obesity
PublicationObesity is a complex medical condition mainly caused by eating habits, genetics, lifestyle, and medicine. The present study deals with traditional diets like the Mediterranean diet, Nordic diet, African Heritage diet, Asian diet, and DASH, as these are considered to be sustainable diets for curing obesity. However, the bioavailability of phytonutrients consumed in the diet may vary, depending on several factors such as digestion...
-
Concrete Compressive Strength Under Changing Environmental Conditions During Placement Processes
PublicationThe technological process of concrete production consists of several parts, including concrete mix design, concrete mix production, transportation of fresh concrete mix to a construction site, placement in concrete framework, and curing. Proper execution of these steps provides good quality concrete. Some factors can disturb the technological process, mainly temperature and excessive precipitation. Changing daily temperature and...
-
FEM and experimental investigations of concrete temperature field in the massive stemwall of the bridge abutment
PublicationThe paper deals with the prediction of early-age concrete temperature of cast-in-place stemwall of the bridge abutment. The considered object is an arch bridge located in Gda´nsk. In the case of massive structures, it is particularly important to not exceed the temperature difference between the core and the concrete surface. Too high temperature gradient generates an increase in thermal stresses, what could be the reason of exceeding...
-
Phosphoroorganic Metal Complexes in Therapeutics
PublicationThe present mini-review highlights recent developments on antitumor activity of metal-based therapeutics which have been a subject of researches for the last few decades. In 1965, Rosenberg found that during an electrolysis on platinum electrodes a complex of Pt is generated which inhibited to a great extent a binary fission in Escherichia coli bacteria. This discovery started a new chapter in medicinal chemistry and the interesting...
-
Cure kinetics of epoxy/MWCNTs nanocomposites: Nonisothermal calorimetric and rheokinetic techniques
PublicationNonisothermal calorimetric and isothermal rheokinetic analyses were used to study cure kinetics of epoxy/anhydride systems containing very low concentration of pristine and amine-functionalized multiwalled carbon nanotubes (MWCNTs). Isoconversional methods were applied in calorimetric modeling of cure kinetics. Eα vs. α dependency and autocatalytic nature of curing were identified for both types of nanocomposites by isoconversional...
-
Biomechanical testing of bioactive bone cements – a comparison of the impact of modifiers: antibiotics and nanometals
PublicationApart from its bone filler and fracture stabilizing function, bone cement can be used as a carrier of bioactive substances, and such modified bone cement can protect the implant against microorganisms, treat local infections and combat bacteria introduced during the surgical procedure. In this paper, the effects of modifying antibiotics and nanosilver on the biomechanical properties of bone cement were examined. The following tests...
-
Curing characteristics, mechanical and thermal properties of reclaimed ground tire rubber cured with various vulcanizing systems
PublicationGround tire rubber was thermo-mechanical reclaimed at 120 °C using a co-rotating twin screw extruder. The effect of vulcanizing system type on curing characteristics, static mechanical properties (tensile strength, elongation-at-break, hardness and resilience), dynamic mechanical properties and thermal properties of reclaimed ground tire rubber was investigated. Reclaimed rubber was cured using different types of vulcanization...
-
Cure Index demonstrates curing of epoxy composites containing silica nanoparticles of variable morphology and porosity
PublicationAn image was taken by Cure Index on curability of epoxy with silica nanoparticles having variable morphology and porosity. Three kinds of silica nanoparticles with non-porous curved-rod, non-porous spherical, and mesoporous spherical microstructures were synthesized and characterized by Fourier-transform infrared spectroscopy, scanning electron microscopy (SEM) and Brunauer–Emmett–Teller analyses. Epoxy nanocomposites containing...