Search
displaying 1000 best results Help
Search results for: FAR-SIDE DEFECT
-
A Comparative Study on Methods of Distinction Between Near- and Far-Side Defects as Techniques Used Alongside with the Magnetic Flux Leakage Testing
PublicationResults of the finite element analysis show that a far-side defect in a steel plate, with the depth greater by 10% of the plate thickness than a near-side defect, can produce a very similar magnetic flux leakage (MFL) signal. Due to the fact that a measurement of MFL itself can lead to misclassification of a far-side defect as a near-side one, and thus to underestimation of its depth, a comparative study of three complementary...
-
Magnetic flux leakage signals of far side defects measured with different velocities
Open Research DataThe dataset contains raw signals measured with the use of the magnetic flux leakage (MFL) technique. Linear Hall effect sensors A1324 were used to measure magnetic flux leakage. Three voltage signals were measured: Bx sensor output, Bz1 sensor output, and difference of Bz1 and Bz2 outputs. An output of a Bx sensor was directly proportional to the tangential...
-
Effects of FSW Tool Plunge Depth on Properties of an Al-Mg-Si Alloy T-Joint: Thermomechanical Modeling and Experimental Evaluation
PublicationOne of the main challenging issues in friction stir welding (FSW) of stiffened structures is maximizing skin and flange mixing. Among the various parameters in FSW that can affect the quality of mixing between skin and flange is tool plunge depth (TPD). In this research, the effects of TPD during FSW of an Al-Mg-Si alloy T-joint are investigated. The computational fluid dynamics (CFD) method can help understand TPD effects on FSW...
-
Dual role of oxygen-related defects in the luminescence kinetics of AlNMn2+
Open Research DataThis dataset presents the impact of temperature and pressure on AlN:Mn2+ luminescence kinetics. Unusual behavior of Mn2+ optical properties during UV excitation is observed, where a strong afterglow luminescence of Mn2+ occurs even at low temperatures. When the temperature increases, the contribution of the afterglow luminescence is further enhanced,...
-
Performance of organic coatings upon cyclic mechanical load
PublicationA number of engineering structures fail due to the fatigue damage resulting from cyclic mechanical stress. However, as far as organic coatings are concerned this degradation factor remains underestimated. In the paper the authors propose a methodology combining global electrochemical impedance spectroscopy and local atomic force microscopy measurements for evaluation of coating resistance to an impact of repetitive mechanical stress. Typical...
-
Environmentally Oriented Models and Methods for the Evaluation of Drug x Drug Interaction Effects
PublicationThis detailed review compares known and widely used methods for drug interaction estimation, some of which now have historical significance. Pharmaceutical application has been noted as far back as several thousand years ago. Relatively late in the 20th century, however, researchers became aware that their fate and metabolism, which still remain a great challenge for environmental analysts and risk assessors. For the patient’s...
-
Convenient synthesis of 3-phosphono-β-lactams through the cyclization ofN-alkenyl-phosphonoacetamides
PublicationOxidative cyclization through the treatment by the transition metals is convenientsynthetic tool with a great number of applications. In the most cases the result is the formationof C-C bond between generated radical and unsaturated part of the same or another molecule.As it was presented by Trogolo it is also suitable way to obtain 4-membered heterocyclicβ-lactamic ring[1]. In this communicate we want to present new application...
-
Shaping the brand awareness of science and technology parks in Eastern Poland
PublicationThe main aim of the paper is the analysis of the effects of actions undertaken so far that have aimed at shaping brand awareness of the parks in Eastern Poland, supported under the OP DEP. The authors focused on the demand-side perspectiveand scrutinized two vectors of conscious branding: the surrounding environment and communication with customers. The group of potential customers underwent qualitative research (ITI interviews)....
-
Structural and Material Determinants Influencing the Behavior of Porous Ti and Its Alloys Made by Additive Manufacturing Techniques for Biomedical Applications
PublicationOne of the biggest challenges in tissue engineering is the manufacturing of porous structures that are customized in size and shape and that mimic natural bone structure. Additive manufacturing is known as a sufficient method to produce 3D porous structures used as bone substitutes in large segmental bone defects. The literature indicates that the mechanical and biological properties of scaffolds highly depend on geometrical features...
-
Biopolymers and Their Composites for Drug Delivery: A Brief Review
PublicationIn recent years, excipient development has become a core area of research in pharmaceutical drug delivery because it influences the formulation development and drug delivery process in various ways. Polymeric drug delivery systems have been of great interest for controlled delivery as they show the great advantage in drug delivery systems because of optimized drug loading and releasing property. Then, the side effects of synthetic...
-
Differential Quadrature Method for Dynamic Buckling of Graphene Sheet Coupled by a Viscoelastic Medium Using Neperian Frequency Based on Nonlocal Elasticity Theory
PublicationIn the present study, the dynamic buckling of the graphene sheet coupled by a viscoelastic matrix was studied. In light of the simplicity of Eringen's non-local continuum theory to considering the nanoscale influences, this theory was employed. Equations of motion and boundary conditions were obtained using Mindlin plate theory by taking nonlinear strains of von Kármán and Hamilton's principle into account. On the other hand, a...
-
Poroelastic Road Surfaces - State of The Art
PublicationPoroelastic Road Surfaces (PERS) constitute a specific group of pavements containing a great amount of crumbled rubber. In most cases rubber aggregate constitutes about 20% of the mixture (by weight) and a polyurethane resin is used as a binder. As a result, PERS is characterized by a much higher elasticity than asphalt and a high porosity typical for drainage pavements. Due to this, tire/road noise is greatly reduced and on top...
-
Surface sliding in human abdominal wall numerical models: Comparison of single-surface and multi-surface composites
PublicationDetermining mechanical properties of abdominal soft tissues requires a coupled experimental-numerical study, but first an appropriate numerical model needs to be built. Precise modeling of human abdominal wall mechanics is difficult because of its complicated multi-layer composition and large variation between specimens. There are several approaches concerning simplification of numerical models, but it is unclear how far one could...
-
Antibiotic-sterol interactions provide insight into the selectivity of natural aromatic analogues of amphotericin B and their photoisomers
PublicationAromatic heptaene macrolides (AHMs) belong to the group of polyene macrolide antifungal antibiotics. Members of this group were the first to be used in the treatment of systemic fungal infections. Amphotericin B (AmB), a non-aromatic representative of heptaene macrolides, is of significant clinical importance in the treatment of internal mycoses. It includes the all-trans heptaene chromophore, whereas the native AHMs contain two...
-
Application of different building representation techniques in HEC-RAS 2-D for urban flood modeling using the Toce River experimental case
PublicationThis paper presents the impact of the choice of building representation techniques and hydrodynamic models on urban flood simulations using HEC-RAS 2-D for the Toce River physical model. To this end, eight numerical models based on previous laboratory experiments were prepared to simulate unsteady urban flooding on each side of building units. Two simplified building layouts (aligned and staggered) were examined, where models were...
-
INTERLABORATORY COMPARISON OF THE ELECTROMAGNETIC EMISSION MEASUREMENTS USING FAR AND GTEM TEST SITES UP TO 1 GHz
PublicationElectromagnetic emission limiting is one of the basic requirements in the European Directive 2014/30/EU (EMC Directive). Manufacturers often use alternative methods of measurements to make preliminary verification of emission. This paper presents and analyzes problem with comparison between measurements in different test sites: FAR (Fully Anechoic Room) and GTEM (Gigahertz Transverse Electromagnetic cell). FAR is assumed as the...
-
Client-side versus server-side geographic data processing performance comparison: Data and code
PublicationThe data and code presented in this article are related to the research article entitled “Analysis of Server-side and Client-side Web-GIS data processing methods on the example of JTS and JSTS using open data from OSM and Geoportal” (Kulawiak et al., 2019). The provided 12 datasets include multi-point and multi-polygon data of different scales and volumes, representing real-world geographic features. The datasets cover the area...
-
Stability of trusses with linear elastic side-supports
PublicationThe present research is devoted to study of a lateral buckling of truss with linear elastic side supports. The elastic support reaction in relation to force in compressed chord and coefficient of buckling length related to side support distance are also calculated. The effect of slope of side support on limit force is also considered. The nonlinear analysis of two roof trusses are carried out. The results are compared to design...
-
Defect and Diffusion Forum
Journals -
Dendron to Central Core S1–S1 and S2–Sn (n>1) Energy Transfers in Artificial Special Pairs Containing Dendrimers with Limited Numbers of Conformations
PublicationTwo dendrimers consisting of a cofacial free-base bisporphyrin held by a biphenylene spacer and functionalized with 4-benzeneoxomethane (5-(4-benzene)tri-10,15,20-(4-n-octylbenzene)zinc(II)porphyrin) using either five or six of the six available meso-positions, have been synthesized and characterized as models for the antenna effect in Photosystems I and II. The presence of the short linkers, -CH2O-, and long C8H17 soluble side...
-
Membrane Sterols Modulate the Binding Mode of Amphotericin B without Affecting Its Affinity for a Lipid Bilayer
PublicationMembrane-active antibiotics are known to selectively target certain pathogens based on cell membrane properties, such as fluidity, lipid ordering, and phase behavior. These are in turn modulated by the composition of a lipid bilayer and in particular by the presence and type of membrane sterols. Amphotericin B (AmB), the golden standard of antifungal treatment, exhibits higher activity toward ergosterol-rich fungal membranes, which...
-
Far Eastern Entomologist
Journals -
DSP techniques in wow defect evaluation
PublicationReferat przedstawia dwie metody określania przebiegu pasożytniczego drżenia dźwięku. Obie wykorzystują analizę pasożytniczych artefaktów. Wybrane artefakty to: przydźwięk sieciowy i wysokoczęstotliwościowy prąd podkładu. Precyzyjny przebieg zniekształcenia kołysania oblicza się wykorzystując informacje zawarte w widmie sygnałów, a uzyskane poprzez STFT lub modelowanie AR. Referat zawiera opis eksperymentów i uzyskane wyniki.
-
Monitoring of single-side lap grinding with electroplated tools
PublicationThe results presented in the paper show that utilising microphones as audible sound sensors is a suitable approach for monitoring a single-side lap grinding process due to the low levels of noise generated by the drives of a machine tool. The results confirm that sound signal analysis is a feasible and relatively simple method to monitor a lap grinding process with the use of an audible sound sensor. Proposed method can be used...
-
Bending and buckling formulation of graphene sheets based on nonlocal simple first-order shear deformation theory
PublicationThis paper presents a formulation based on simple first-order shear deformation theory (S-FSDT) for large deflection and buckling of orthotropic single-layered graphene sheets (SLGSs). The S-FSDT has many advantages compared to the classical plate theory (CPT) and conventional FSDT such as needless of shear correction factor, containing less number of unknowns than the existing FSDT and strong similarities with the CPT. Governing...
-
Quasi-analytical Near-to-Far Field Transformation Based on Field Matching Method for Scattering Problems
PublicationA new quasi-analytical near-to-far field transformation based on field matching method (field expansion in a base of Hankel functions) is presented. This approach uses finite element method to obtain near field, then the field is expressed in a base of Hankel functions. The evaluated coefficients allow to calculate the field outside the numerical domain, also in a far distance. The main advantage of the proposed technique is avoiding of...
-
The Imaging of Gdansk Bay Seabed by Using Side Sonar
PublicationThis paper is mainly aimed at presentation of an impact of environmental conditions on imaging accuracy by using hydro-acoustic systems in waters of a high non-uniformity of spatial distribution of hydrological parameters. Impact of refraction on erroneous estimation of range, in case of wave radiation into water under a large angle, like in side sonars or multi-beam echo-sounders, is especially important. In this paper seasonal...
-
Access to Side-On Bonded Tungsten Phosphanylphosphinidene Complexes
PublicationMetathesis reactions between diimido complexes of tungsten(VI)[(ArN)2WCl2] (Ar = 2,6-iPr2C6H3) and lithium derivatives of diphosphanes R2P-P(SiMe3)Li (R = tBu and iPr) yield two anionic diimido complexes of tungsten with side-on bonded phosphanylphosphinidene ligands, [(ArN)2WCl(η2-R2P-P)]-. Both complexes are structurally characterized. A possible reaction mechanism and the role of donor solvents are discussed on the basis of...
-
Sensitivity analysis of critical forces of trusses with side bracing
PublicationThe present research is devoted to the study of out-of-plane buckling of trusses with elastic side bracing. Inthis paper, a sensitivity analysis of critical buckling loads of a truss due to bracing stiffness is carried out. A method based on the sensitivity analysis for the determination of the threshold bracing stiffness conditionfor full bracing of a truss is proposed. The influence lines of the unit change of the bracing stiffness...
-
Seafloor relief reconstruction from side scan sonar data
PublicationSide scan sonar is one of the most widely used imaging systems in the underwater environment. It is relatively cheap and easy to deploy, in comparison with more powerful sensors. Although side scan sonar does not provide seafloor bathymetry directly, its records are directly related to seafloor images. In the paper, the method for 3D seafloor relief reconstruction from side scan sonar data is presented. The method is based on the...
-
Stability of truss with side - supports. The case of linear and rotational elastic supports
PublicationThe research is devoted to study lateral buckling of truss with linear and rotational elastic side-supports. Geometrically nonlinear analysis of example truss with linear and rotational elastic sidesupports is carried out. The limit normal force in compressed chord of the truss due to stiffness of side supports is calculated. The elastic support reaction in relation to force in compressed chordand coefficient of buckling length...
-
A Low-Cost System for Far-Field Non-Anechoic Measurements of Antenna Performance Figures
PublicationPrototype measurements are the key step in the development of antenna structures. Typically, their far-field characteristics are validated in expensive, dedicated facilities such as open range sites, or anechoic chambers. Despite being necessary for obtaining high-precision data (e.g., for device qualification), the use of costly infrastructure might not be fully justified when the main goal of measurements includes demonstration...
-
Wow defect reduction based on interpolation techniques
PublicationW artykule przedstawiono wyniki badania różnych technik interpolacji wykorzystanych w redukcji kołysania dźwięku. W badaniach użyto: interpolację liniową, techniki interpolacji wielomianowej, i interpolację funkcją sink. Jakość rekonstrukcji zbadano wykorzystując sztucznie spreparowany sygnał foniczny, zrekonstruowany wymienionymi metodami interpolacji. Jakość rekonstrukcji oceniono wykorzystując standardowe deskryptory jakości...
-
Wow defect reduction based on interpolation techniques
PublicationW referacie przedstawiono wyniki badania różnych technik interpolacji wykorzystanych w redukcji kołysania dźwięku. W badaniach użyto: interpolację liniową, dwie techniki interpolacji wielomianowej (Hermite i spline), i technikę sumowania okienkowanych funkcji sink. Jakość rekonstrukcji wykonano wykorzystując sztucznie spreparowany sygnał audio, rekonstruowany wymienionymi metodami interpolacji. Jakość rekonstrukcji oceniono wykorzystując...
-
Don't forget the dark side of green transformation
PublicationDesign/methodology/approach – The study is a continuation of the research by Durst and Zieba (2019) related to knowledge risks and their potential outcomes. This present study makes an update on the literature on knowledge risks and green transformation and describes knowledge risks that can be faced in this process. Originality/value – The paper offers new insights for researchers dealing with the topic of knowledge risks in...
-
The best porous asphalt pavement in Sweden so far
PublicationIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed in various versions on the E4 motorway through the Swedish city Huskvarna. As a result of a court decision the Swedish Transport Administration had to reduce noise emission by applying a low noise road surface that would reduce A-weighted noise levels by 5 dB, as an average. Earlier experience in Sweden indicated that it was possible to obtain a high...
-
Proximity and Innovation in Clusters: How Close, How Far?
PublicationThe concept of proximity, whilst attractive cognitively, is still a poorly explored area in management sciences. The earliest publications on proximity were published at the end of the twentieth century and the development of this concept was strongly influenced by The French School of Proximity (Kirat & Lung, 1999; Rallet & Torre, 1999; Torre & Gilly, 2000; Carrincazeaux et al., 2001; Torre & Rallet, 2005). However, the most influential...
-
Visualization of a lifeboat motion during lowering along ship’s side
PublicationThis paper presents description of a computer program for motion visualization of a lifeboat lowered along ship’s side. The program is a post-processor which reads results of numerical calculations of simulated objects’ motions. The data is used to create scene composed of 3D surfaces to visualize mutual spatial positions of a lifeboat, ship’s side and water waving surface. Since the numerical data contain description of a simulation...
-
Including the Dark Side of Entrepreneurship in the Entrepreneurship Education
PublicationPursuing an entrepreneurial career is often rewarding in terms of both economic and psychological outcomes. However, becoming an entrepreneur also has its darker side that affects professional and personal life. Meanwhile, the positivity bias is prevalent in entrepreneurial education and research. It is recognized as emphasizing the advantages of becoming an entrepreneur and giving considerably less attention to potential downsides....
-
Video of LEGO bricks on conveyor belt - Bricks with studs on the side
Open Research DataThe set contains videos of LEGO bricks (bricks with studs on the side) moving on a white conveyor belt. The videos were prepared for training neural network for recognition of LEGO bricks. The bricks were separated as much as possible and in most cases they should not overlap. The images were taken from different sides by stationary camera located over...
-
Video of LEGO bricks on conveyor belt - Plates with studs on the side
Open Research DataThe set contains videos of LEGO bricks (plates with studs on the side) moving on a white conveyor belt. The videos were prepared for training neural network for recognition of LEGO bricks. The bricks were separated as much as possible and in most cases they should not overlap. The images were taken from different sides by stationary camera located over...
-
Interconnection of the Customer-Side Resources Using Single Phase VAPF
PublicationThe paper introduces method for utilization of the customer-side generated energy using single phase voltage active power filter. Structure and control method of the power electronics converter has been described and some simulation results are shown to prove usefulness of this arrangements. Proposed application realizes the following functions: power quality improvement, uninterruptible supplying and energy costs reduction.
-
Measurement of transverse force with polarization-maintaining side-hole fibers.
PublicationW pracy badano możliwości wykorzystania przenoszących stan polaryzacji światłowodów typu Side-Hole do pomiaru siły działającej prostopadle do osi symetrii światłowodu. Na podstawie wyników modelowania stwierdzono, ze niektóre światłowody tego typu charakteryzują się większą czułością aniżeli standardowe światłowody przenoszące stan polaryzacji. W wyniku przeprowadzonych pomiarów potwierdzono wyniki modelowania.
-
Has EGNOS its own place in maritime navigation?
PublicationGNSS (in fact it usually means GPS) is at the moment the fundamental means of positioning for any variants of navigation. However some attributes of it can be not sufficient for every users or in some tasks, so there are any cases when this system needs support. From the mariner point of view pure GPS properties perfectly fulfils expectations of sailors at the open sea, however there are lot of cases, when accuracy of the system...
-
Estimating the uncertainty of discharge coefficient predicted for oblique side weir using Monte Carlo method
PublicationSide weir is a hydraulic structure, which is used in irrigation systems to divert some water from main to side channel. It is installed at the entrance of the side channel to control and measure passing water into the side channel. Many studies provided side weir water surface profile and coefficient of discharge to measure water discharge diverted into the side channel. These studies dealt with different side weir shapes (rectangular,...
-
Receiver-side fingerprinting method based on quaternion sandwich product
PublicationIn this paper a new receiver-side fingerprinting method for color images is proposed. The proposed method belongs to the group of Joint Fingerprinting and Decryption (JFD) methods. Each component of the color image is represented as a point in 3D space, which is formed by 3 color channels. Encryption and fingerprinting can be interpreted as rotation, scaling and translation of these points. Calculations are performed using quaternion...
-
Analysis of server-side and client-side Web-GIS data processing methods on the example of JTS and JSTS using open data from OSM and geoportal
PublicationThe last decade has seen a rapid evolution of processing, analysis and visualization of freely available geographic data using Open Source Web-GIS. In the beginning, Web-based Geographic Information Systems employed a thick-client approach which required installation of platform-specific browser plugins. Later on, research focus shifted to platform-independent thin client solutions in which data processing and analysis was performed...
-
Investigation on polypropylene friction stir joint: effects of tool tilt angle on heat flux, material flow and defect formation
PublicationTool tilt angle (TTA) is a critical factor that can control material flow in polymeric materials' friction stir joining (FSJ). This study selected a TTA range between 0° to 4° for FSJ of polypropylene (PP) polymer sheet. A modified computational fluid dynamic (CFD) technique was implemented to gain a deep understanding of the effects of TTA during FSJ of PP. The PP joint's internal flow, defect formation, heat generation, and tensile...
-
Defect-induced conductance oscillations in short atomic chains
Publication -
One-Step Synthesis of b-Lactams with Retro-Amide Side Chain
PublicationAbstract: A one pot synthesis for preparation of 1,4-disubstituted-2-oxo-azetidine-3-carboxylic acid amides was developed. 5-(α-N-substituted-amino-α'-hydroxy)methylene Meldrum's acids act as a source of ketenes that react with aldimines in boiling toluene to give b-lactams with retro-amid side chain.