Search results for: condensation
-
Evaporation and condensation
PublicationW pracy przedstawiono encyklopedyczne ujęcie wrzenia i kondensacji.
-
COMPARISON OF TWO MODELS OF CONDENSATION
PublicationIn the low-pressure part of steam turbine, the state path usually crosses the saturation line in penultimate stages. At least last two stages of this part of turbines operate in two –phase region. The liquid phase in this region in mainly created in the process of homogeneous and heterogeneous condensation. Several observations confirm however, that condensation often occurs earlier than it is predicted by theory i.e. before the...
-
Non-isothermal effects in condensation inside tubes
PublicationWrzenie i kondensacja w przepływie są zjawiskami symetrycznymi, aczkolwiek ich opis za pomocą jednej korelacji w konfrontacji z eksperymentem nie dawał dobrych rezultatów. W pracy zmodyfikowano naprężenia styczne na granicy rozdziału faz w ten sposób, że uwzględniono wymianę pędu na granicy rozdziału faz i możliwym stała się adaptacja wcześniej zaproponowanego przez autorów modelu wrzenia w przepływie do obliczeń wymiany ciepła...
-
Estimation of the steam condensation flow via CFD methods
PublicationThe results of numerical simulations to predict the performance of different steam models have been presented. All of the considered models of steam condensation have been validated on the base of benchmark experiment employing expansion in nozzle and next on the low pressure part of the steam turbine stage. For numerical analysis three models have been finally used – the ideal steam model without condensation, an equilibrium steam...
-
„Eulerian – Eulerian” versus ,,Eulerian –Lagrangean” models of condensation
PublicationLiquid phase in the flowing vapor through stages of the steam turbine is the cause of a lot of failures. Nowadays, due to work of steam turbines at partial load, process of homogeneous and heterogeneous condensation still is current. The formation of drops of condensate under conditions other than nominal operation of turbine is a process still unknown. Engineers and designers involved in the development of power station machines...
-
Heat and mass exchange in the process of condensation on critical droplets.
PublicationSformułowano model wzrostu kropli krytycznej podając równania zmiany masy i temperatury kropli. Pokazano formę zlinearyzowaną tych równań dobrze aproksymującą wzrost kropli w poblizu wymiaru krytycznego. Podano rozwiązanie układu zlinearyzowanego uzależniając zmianę temperatury od zmiany masy kropli i czasu charakterystycznego.
-
Experimental investigations on condensation in flow in small diameter channels
PublicationW pracy przedstawiono innowacyjne podejście do eksperymentalnych badań kondensacji w przepływie oraz omówiono wstępne wyniki badań eksperymentalnych kondensacji etanolu w pionowej rurce srebrnej o średnicy wewnętrznej 2.3 mm.
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationFlow boiling and flow condensation are often regarded as two opposite or symetrical phenomena. Their description however with a single correlation has yet to be suggested.In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the buble generetion is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such case...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena, however their description with a single correlation has yet to be suggested. In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the bubble generation is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationIn the paper a method developed earlier by the first author is applied to calculations of heat transfer coefficient for inside tube condensation. The method has been verified using experimental data from literature on several fluids in different microchannels and compared to three well established correlations.
-
Pressure drop of HFE7000 and HFE7100 during flow condensation in minichannels
PublicationAttention is focused on the issues of flow resistance and pressure drop of perspective refrigeration fluids during condensation in the two-phase flow in minichannels. The case of the flow through a cylindrical single channel of 2.3 mm inner diameter was carefully analyzed. Pressure drop tests have been performed in diabatic flow conditions. The effect of heat flux, mass flux, vapour quality and saturation temperature on the two-phase...
-
Remarks on steam condensation modeling related to steam turbine large output
PublicationIn the paper numerical simulations have been performed to predict the performance of the diferent steam models. All of the considered models of steam condensation have been validated on the base of benchmark experiment employing expansion in nozzle and next on the low pressure part of the steam turbine equipped with the so-called Baumann stage. For numerical analysis three models have been finally used - the ideal steam model without...
-
Experimental investigations on condensation in flow of HFE-7100 in small diameter channels
PublicationIn the paper the authors present investigations of flow condensation with the use of the HFE-7100 as a working fluid. The original and new approach to removing the heat from the channel was applied. The research was carried out using a wide-range real time observations, e.g. using infrared camera and stroboscope microphotography. This paper presents the details of experiment as well as the influence of heat and flow parameters...
-
Experimental investigations on condensation in flow of HFE-7100 in small diameter channels
PublicationW pracy przedstawiono wyniki badań eksperymentalnych kondensacji czynnika HFE-7100 w minikanale o średnicy wewnętrznej 2.3 mm. Opisano również oryginalne podejście w prowadzeniu badań nad uzyskaniem lokalnych wartości współczynnika przejmowania ciepła podczas kondensacji w przepływie.
-
Pressure drop and heat transfer during boiling and condensation at subcritical region
PublicationMost of the data presented in the literature relate to saturation temperatures in the range - 20°C to 40°C due to the application in refrigeration technology. There is necessity to extend databases to higher values of saturation temperature due to new applications such as Organic Rankine Cycle and high temperature heat pumps. Only few papers contain data for high reduced pressure for low boiling point liquids. This paper focus...
-
Experimental investigations on pressure drop during the condensation in flow of HFE7000 in vertical minichannel
PublicationIn the work presented in the paper authors focused attention on the issues of flow resistance and pressure drop during condensation in the flow. The case of the descending flow through a cylindrical single-channel of 2.3 mm inner diameter was carefully analyzed. In the course of investigations a new working fluid HFE 7000 has been scrutinised which has a strongly differing properties in comparison to the other fluids that are commonly...
-
PRESSURE DROP OF HFE7000 AND HFE7100 IN FLOW CONDENSATION IN MINICHANNELS WITH ACCOUNT OF NON-ADIABATIC EFFECTS
PublicationFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena involving the change of phase. There is a temptation to describe both these phenomena with one only correlation. From amongst the structures present in flow boiling and flow condensation at least the annular flow structure seems to be mostly appropriate to the common modeling. However, the shear stress acting between vapor phase and liquid...
-
Non-adiabatic Effects in Pressure Drop Calculations in Flow Boiling and Flow Condensation in Minichannels
PublicationConsiderations presented in the paper relate both to the case of flow boiling and flow condensation in conventional channels as well as small diameter ones. Authors devoted all the possible attention that the modeling presented is applicable to the whole range of quality variation in both cases of condensation and boiling. The form of two-phase flow multiplier, which is a major factor in modeling presented here, should be capable...
-
Determination of pressure drop in flow condensation of HFE7000 in minichannels with account of non-adiabatic effects
PublicationFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena involving the change of phase. There is a temptation to describe both these phenomena with one only correlation, however such method has yet to be suggested. From amongst the structures present in flow boiling and flow condensation at least the annular flow structure seems to be mostly appropriate to the common modeling. However, the shear...
-
Efficient method for Knoevenagel condensation in aqueous solution of amino acid ionic liquids (AAILs)
Publication -
Catalytic aldol condensation of formaldehyde with acetic acid on titanium phosphates modified by different techniques
Publication -
Thermal-hydraulic issues of flow boiling and condensation in organic Rankine cycle heat exchangers
PublicationW pracy przedstawiono szereg zagadnień cieplno-przepływowych podczas wrzenia i kondensacji w przepływie w wymiennikach ciepła obiegu ORC. Uwzględniono przemiany fazowe. Analizowano zagadnienia stabilności pracy wymienników oraz ich dynamikę
-
Inert gas condensation made bimetallic FeCu nanoparticles - plasmonic response and magnetic ordering
Publication -
Comparitive study of heat transfer and pressure drop during flow boiling and flow condensation in minichannels
PublicationIn the paper a method developed earlier by authors is applied to calculations of pressure drop and heat transfer coefficient for flow boiling and also flow condensation for some recent data collected from literature for such fluids as R404a, R600a, R290, R32,R134a, R1234yf and other. The modification of interface shear stresses between flow boiling and flow condensation in annular flow structure are considered through incorporation...
-
Calculation method for flow boiling and flow condensation of R134a and R1234yf in conventional and small diameter channels
PublicationThe paper presents the results of calculations performed using the authors’ model to predict the heat transfer coefficient during flow boiling for two refrigerants R134a and R1234yf. The experimental data from various past studies have been collected and the calculations have been conducted for the full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house...
-
Early stages of condensation from the gaseous phase in a H2O-N2 system: a molecular dynamics study.
PublicationW pracy przedstawiono wyniki symulacji wczesnych etapów kondensacji z fazy gazowej w układzie xH2O (1-x)N2. Przeanalizowano całkowitą liczbę klastrów, średni rozmiar klastra i rozmiar klastra maksymalnego w funkcji czasu.
-
EXPERIMENTAL VERIFICATION OF THE METHOD OF FLOW BOILING AND FLOW CONDENSATION HEAT TRANSFER PREDICTION FOR SELECTED FLUIDS
PublicationIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of different refrigerants. The experimental data from various research studies from literature were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in- house developed model....
-
Numerical model for thin liquid film with evaporation and condensation on solid surfaces in systems with conjugated heat transfer
PublicationCondensation and evaporation processes from wetted surfaces are of utmost importance in many technological or industrial applications. In many devices such as home-appliances and air conditioning systems just to name a few, condensation and evaporation processes greatly impact their performance and energy efficiency; The physics of these processes is quite complex, involving conjugate heat transfer among solid–liquid film-gaseous...
-
A novel concept of enhanced direct-contact condensation of vapour- inert gas mixture in a spray ejector condenser
PublicationAn analytical model of direct steam condensation (DCC) in the novel idea of spray ejector condenser (SEC) in the presence of inert gas has been developed. It is based on continuity, momentum and energy equations for the steam-carbon dioxide mixture and direct contact condensation mechanisms due to heat transfer and concentration. Crucial in the process of DCC is atomisation of the motive fluid in the ejector. The effect of atomised...
-
Direct-contact condensation from vapour- gas mixture in a spray ejector condenser for negative CO2 power plant
PublicationDirect-contact condensation of vapour containing the inert gas on a spray of subcooled liquid exists in a number of technical applications. For example, it may be found in the nuclear industry (e.g. pressurized jet under normal operating conditions, in safety analyses) or in the chemical industry (e.g. mixing-type heat exchanger, degasser, sea water desalting). The problem is also essential to modelling and analysis of some...
-
Controlling nodal displacement of pantographic structures using matrix condensation and interior-point optimization: A numerical and experimental study
PublicationThis study presents an innovative approach for the precise control of nodal displacements in pantographic structures. The method is founded on the Matrix Condensation of Force Method, seamlessly integrated with an Interior Point Optimization algorithm. This combination offers a unique advantage by allowing users to manipulate displaced nodes within a defined coordination domain. Furthermore, this approach introduces the Interior...
-
Non-isothermal effects in a common method for calculation of heat transfer coefficient in flow boiling and flow condensation in minichannels
PublicationW pracy przestawiono efekty nieizotermiczne w metodzie wyznaczania współczynnika przejmowania ciepła podczas wrzenia w przepływie oraz kondensacji w przepływie w minikanałach. Wyniki obliczeń porównano z badaniami eksperymentalnymi z literatury, uzyskując dobrą zgodność.
-
A common method for calculation of flow boiling and flow condensation heat transfer coefficients in minichannels with account of nonadiabatic effects
PublicationW pracy przedstawiono metodę ogólną wyznaczania współczynników przejmowania ciepła podczas wrzenia w przepływie i kondensacji w przepływie w minikanałach z uwzględnieniem efektu nieadiabatycznego. Uwzględnia ona wpływ modyfikacji naprężeń stycznych na granicy ciecz-para na wymianę ciepła.
-
Multi-objective optimization of the ORC axial turbine for a waste heat recovery system working in two modes: cogeneration and condensation
PublicationDue to the demand of the district heating network and electric power grid ORC turbines can operate in the condensation and cogeneration modes. This approach requires the design of an expander which is characterized by high efficiency in each mode of operation. The paper is devoted to a multi-objective efficiency optimization of a one stage axial ORC turbine working on MM (Hexamethyldisiloxane). An Implicit Filtering algorithm (IF)...
-
Analytical model with non-adiabatic effects for pressure drop and heat transfer during boiling and condensation flows in conventional channels and minichannels
PublicationIn the paper a method developed earlier by authors is applied to calculations of pressure drop and heat transfer coefficient for boiling flow and condensation flow with account of non- adiabatic effects for some recent data collected from literature. The first effect, the modification of interface shear stresses in annular flow pattern is considered through incorporation of the so called "blowing parameter". The mechanism of...
-
Application of Feed Forward Neural Networks for Modeling of Heat Transfer Coefficient During Flow Condensation for Low and High Values of Saturation Temperatur
PublicationMost of the literature models for condensation heat transfer prediction are based on specific experimental parameters and are not general in nature for applications to fluids and non-experimental thermodynamic conditions. Nearly all correlations are created to predict data in normal HVAC conditions below 40°C. High temperature heat pumps operate at much higher parameters. This paper aims to create a general model for the calculation...
-
Response to the queries raised by Dr M.M. Awad in a letter to editor comments on “Pressure drop of HFE7000 and HFE7100 during flow condensation in minichannels”
Publication.
-
Results of implementation of Feed Forward Neural Networks for modeling of heat transfer coefficient during flow condensation for low and high values of saturation temperature
Open Research DataThis database present results of implementation of Feed Forward Neural Networks for modeling of heat transfer coefficient during flow condensation for low and high values of saturation temperature. Databse contain one table and 7 figures.
-
Effect of the inclination angle of the condenser on the heat transfer coefficient value – experimental study
PublicationWhen considering problem of the condensation of the refrigerant in a flow inside channel, one needs to pay attention to the shape of its cross-section, the hydraulic diameter, the channel length as well as the orientation of the channel axis in space (horizontal, vertical, inclined). This paper presents an experimental study concerning the effect of the inclination angle of the condenser with a single coil pipe on the heat transfer...
-
An asymmetrical λ-foot of condensing steam flow in the IMP PAN nozzle
PublicationIn the present paper we have focused on the precise prediction of the spontaneous condensation phenomena in wet steam flow. Novelty of our approach lies on modelling both the moment of initiation of a phase transition, as well as the moment of its reverse progress - called here re-vaporization of the condensate phase. The practical issue is to elaborate of a model of spontaneous condensation/vaporization of water steam flow...
-
Development of a spray-ejector condenser for the use in a negative CO2 emission gas power plant
PublicationOne promising solution for developing low-emission power technologies is using gaseous fuel combustion in pure oxygen when the exhaust gas mixture is composed of H2O and CO2, and where CO2 is separated after steam condensation. The paper presents the results of computational analyses providing to the Spray-Ejector Condenser (SEC) development, which is one of the crucial components of the negative CO2 gas power plant (nCO2PP) cycle...
-
CO2 capture using steam ejector condenser under electro hydrodynamic actuator with non-condensable gas and cyclone separator: A numerical study
PublicationThe concept for condensation of steam and CO2 separation in a negative CO2 emission gas power plant involves the utilization of a steam ejector condenser (SEC) for direct-contact condensation of vapor with inert gas (CO2) on a spray of subcooled liquid, integrated with a separator to produce pure CO2. Due to the increasing diffusion resistance and reduced convective heat transfer between the steam and subcooled water phases...
-
Three phase transient model of wet coal pyrolysis
PublicationA one-dimensional transient mathematical model was developed to describe the thermal and flow phenomena during coal pyrolysis in a coke oven. The model was solved numerically using partly implicit methods for gas flow and heat transfer problems. It was successfully validated with industrial-scale measurements of temperature change in the middle-plane of the coke oven chamber. The evolution of temperature and pressure, distributions...
-
Synthesis of compounds with C-P-P and C=P-P bond systems based on the phospha-Wittig reaction
PublicationA reactivity study of a β-diketiminate titanium(III) phosphanylphosphido complex [MeNacNacTi(Cl){η2-P(SiMe3)-PtBu2}] (1) towards ketones such as benzophenone, 9-fluorenone, acetophenone, cyclopentanone, cyclohexanone and cycloheptanone is reported. The reactions of 1 with aromatic ketones (without α-protons) directly lead to the Ti(III) complex [MeNacNacTi(μ2-Cl)(OSiMe3)] (5) as well as Ti(IV) complexes with the pinacol condensation...
-
Comparative study of operation of condensing and traditional boilers equipped with the ORC module for electricity generation
PublicationCondensing technology applied to boilers is to make full use of thermal energy contained in the fuel. That means that additionaly the heat from condensation of exhaust gases can be used for the purposes of heating the domestic hot water and to cover the demand for central heating. The study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler....
-
Applications of Alkanethiols in Organic Synthesis
PublicationThis manuscript is an update to the earlier Science of Synthesis contribution describing methods for the synthesis of alkanethiols. Thiols can be converted into sulfonic, sulfinic, sulfenic acid and their derivatives, sulfides, disulfides, polysulfides, sulfonium salts, and thiiranes, etc. These transformations are accomplished by nucleophilic displacement or addition, oxidation, condensation, or coupling reactions involving thiol...
-
Metal ion directed template synthesis using 2-acetyl-1,3-indandione and ethylenediamine: steric and electronic restrictions
PublicationA template synthesis using 2-acetyl-1,3-indandione and ethylenediamine results in formation of octahedral Ni complex, whose crystal structure has been resolved using single crystal X-ray diffraction. The structure indicates that only exocyclic enolic oxygen atom of the triketone takes part in the condensation with ethylenediamine.
-
Performance of the domestic micro ORC equipped with the shell-and-tube condenser with minichannels
PublicationIn this paper, the original compact shell-and-tube heat exchanger with circular minichannels of in-house design and manufacturing is presented as the condenser for the domestic micro heat and power plant investigations as well as other future technical applications. The heat exchanger is equipped with turbulizing baffles inside the shell. The shell itself is made of a tubular sleeve having an inner diameter of 0.067 m and the length...
-
High-efficient, zero-emission energy production
PublicationThis paper presents innovative thermodynamiccycles with high-efficient, zero-emission energy production. The main aim of this work is to show the role of nano-phenomena in the enhancement of the power of thermodynamic cycles. For that purpose, the cycles using oxy-combustion and spray ejected condensation are first studied and, secondly hybrid cycles using fuel cells and gas turbines are presented. The role of nano-phenomena in...
-
Analysis of cyclone separator solutions depending on SEC outlet conditions in nCO2PP
PublicationUtilization of spray ejector condenser in order to carry out direct-contact condensation of vapour with inert gas (CO2) on a spray of subcooled liquid integrated with separator (to make pure CO2) has been proposed for the task of condensation and CO2 separation in the negative CO2 emission gas power plant. Condensation and separation has a significant impact on the thermodynamic efficiency of the entire negative CO2 emission gas...
-
Efficient Method for the Synthesis of Functionalized Basic Maleimides
PublicationA three-step procedure involving Diels-Alder condensation of maleic anhydride with furane, formation of N-substituted imide upon reaction with appropriate diamine and a final retro Diels-Alder regeneration of the maleic carbon-carbon double bond is proposed for an unequivocal synthesis of N-substituted basic maleimides. The novel method is characterized by mild reaction conditions, easy work-up, high yields and no need for additional...
-
Giant Nernst effect in the incommensurate charge density wave state of P4W12O44
PublicationWe report the study of Nernst effect in quasi-low-dimensional tungsten bronze P4W12O44 showing a sequence of Peierls instabilities. We demonstrate that both condensation of the electronic carriers in the charge density wave state and the existence of high-mobility electrons and holes originating from the small pockets remaining in the incompletely nested Fermi surface give rise to a Nernst effect of a magnitude similar to that...
-
Dariusz Mikielewicz prof. dr hab. inż.
PeopleProfessor Dariusz Mikielewicz – born on February 6, 1967. in Gdansk. Here in 1974 he enrolled first to the Elementary School No. 17, and then in the Grammar School No. 5, named after Stefan Żeromski in Gdansk-Oliwa. After graduating from the Secondary School, with honors, in 1985 he successfully passed the entrance exams to the Faculty of Mechanical Engineering of Technical University of Gdansk, where he graduated with a very good...
-
Alkanethiolates of Group 1,2, and 13-15 Metals
PublicationThis manuscript is an update to the earlier Science of Synthesis contribution describing methods for the synthesis of alkanethiolates of group 1, 2, and 13-15 metals. Alkanethiolates can be converted into S-alkyl thiocarboxylic acid esters, 1-thioglycosides, S-alkyl thiosulfinates, tetrahydro-1,4-thiazine-3-ones, sulfides, disulfides, sulfonium salts, dithioacetals and dithioketals, etc. These transformations are accomplished by...
-
A study of a compact high-efficiency zero-emission power plant with oxy-fuel combustion
PublicationThis paper discusses the application of global trends in gas cycles technology using oxy-fuel combustion. This is followed by a demonstration of a design solution for a new cycle with two enhanced energy-converting devices, namely a wet combustion chamber and a spray-ejector condenser. The proposed gas and steam cycle unit is contained within a single turbine, whose benefits combine those offered by gas turbines (high inlet temperatures)...
-
Alternative method for the synthesis of imidazo[5,1-f][1,2,4]triazin-4(3H)-one—a substrate for the preparation of phosphodiesterase (5) inhibitors
PublicationImidazo[5,1-f][1,2,4]triazin-4(3H)-ones, as isosteres of purine, are of interest for pharmaceutical research as potential substrates for the synthesis of cGMP-PDE5 inhibitors. We present a novel, alternative method for the synthesis of imidazotriazinones, that differs from the previously reported ones with respect to the method of construction of the triazinone ring in the molecule. The key step in our approach is condensation...
-
Statistics of AFM current-voltage curves
Open Research DataMapping surface electrical conductivity offers enormous cognitive possibilities regarding the structure and properties of modern materials. The technique invented for this purpose (Conductive AFM) by Murrel's team and colleagues allows independent monitoring of the local conductivity of materials in correlation with the topographic profile. The mentioned...
-
Wet H2S corrosion and degradation of pipeline in amine regeneration system
PublicationThe paper presents the results of NDT examinations, metallographic tests and risk assessment of degradation related to corrosion of amine regeneration unit in a desulphurisation system. Intensive corrosion resulting from acid gases environment upon water condensation causes perforation of the pipeline. Detailed analysis reveals cracking related to the mechanism of wet H2S. Hydrogen penetration, resulting from the wet H2S process,...
-
Thermodynamic analysis of the double Brayton cycle with the use of oxy combustion and capture of CO2
PublicationIn this paper, thermodynamic analysis of a proposed innovative double Brayton cycle with the use of oxy combustion and capture of CO2, is presented. For that purpose, the computation flow mechanics (CFM) approach has been developed. The double Brayton cycle (DBC) consists of primary Brayton and secondary inverse Brayton cycle. Inversion means that the role of the compressor and the gas turbine is changed and firstly we have expansion...
-
Rain Water: Atmospheric Deposition
PublicationWater is transferred from the atmosphere to the land surface mainly via various forms of atmospheric precipitation; however, the contribution of surface condensation/deposition (e.g., dew, hoar frost, occult precipitation) should not be neglected. Rainwater and liquid deposits (dew, hoar frost, rime) are components of the physical and geographical environment that are easily assimilated and transported. Thus, they are generally...
-
Performance of the very high-temperature heat pump with low GWP working fluids
PublicationTraditional heat pumps are a very attractive pro-ecological solutions for a number of applications, including providing of heating or heat recovery from industrial processes. The application range of heat pumps could be greatly enlarged when the operating temperature would be increased to 130-150°C and/or the temperature lift can be increased to 50-100 K. In the paper, the very high temperature vapour-compressor based single stage...
-
Comparative study of operation of condensing and traditional boilers equipped with ORC module for electricity generation
PublicationThe study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler. In the case of a conventional boiler there is noted a greater fuel consumption and the greater power generated than in the case of the unit with the condensing boiler. Postulated is the indicator in the form of a ratio of turbine power to the mass flow rate of fuel, which in turn gives...
-
STUDY ON THE EFFECTIVENESS OF THE TURBINE CONDENSER AIR EXTRACTION SYSTEM USING HYDRO EJECTORS
PublicationThe aim of the paper is to investigate the effectiveness of the 18K380 steam turbine condenser air extraction system using hydro ejectors. Motivation for the analysis is a need of improvement of the energy conversion ratio of the power plant. To achieve this goal it is necessary to establish efficiency of each subsystem of the energy cycle. The air extraction system is not a highly power consuming system but it has great impact...
-
Experimental validation of pressure drop models during flow boiling of R134a – effect of flow acceleration and entrainment
PublicationA crucial step to assure proficient work of power and process apparatus is their proper design. A wide array of those devices operates within boiling or condensation of the working fluid to benefit from high heat transfer rates. Two-phase flows are associated with high heat transfer coefficients because of the latent heat of evaporation and high turbulence level between the liquid and the solid surface. Predicting heat transfer...
-
Tetrahydroquinolinone derivatives exert antiproliferative effect on lung cancer cells through apoptosis induction
PublicationThe anticancer properties of quinolones is a topic of interest among researchers in the scientific world. Because these compounds do not cause side effects, unlike the commonly used cytostatics, they are considered a promising source of new anticancer drugs. In this work, we designed a brief synthetic pathway and obtained a series of novel 8-phenyltetrahydroquinolinone derivatives functionalized with benzyl-type moieties at position...
-
Modelling study of flow boiling heat transfer of perspective fluids for refrigeration technology
PublicationThere is a gap of knowledge on flow boiling at high saturation temperatures and higher values of reduced pressure. Thus far, the in-house developed semi-empirical model for flow boiling and flow condensation showed a satisfactory accuracy for calculations for various refrigeration fluids for a wide scope of reduced pressures. This study presents results of calculations of heat transfer coefficient of perspective refrigeration fluids,...
-
A simplified energy dissipation based model of heat transfer for subcooled flow boiling
PublicationIn the paper a model is presented based on energetic considerations for subcooled flow boiling heat transfer. The model is the extension of authors own model developed earlier for saturated flow boiling and condensation. In the former version of the model we used the heat transfer coefficient for the liquid single-phase as a reference level, due to the lack of the appropriate model for heat transfer coefficient for the subcooled...
-
Unsaturated, biobased polyesters and their cross-linking via radical copolymerization
PublicationBiobased, unsaturated polyesters derived from isosorbide, maleic anhydride and succinic acid were synthesized and characterized. The presence of maleic anhydride units in the structure of the polyesters allowed converting them into cured coatings by radical copolymerization with cross-linking agents such as 2-hydroxyethyl methacrylate, N-vinyl-2-pyrrolidinone, acrylic acid or methacrylamide. The investigated polyesters were obtained...
-
INNOVATIVE THERMODYNAMICAL CYCLES BASED ON ENHANCEMENT MASS, MOMENTUM, ENTROPY AND ELECTRICITY TRANSPORT DUE TO SLIP, MOBILITY, TRANSPIRATION, ENTROPY AND ELECTRIC JUMPS AS WELL AS OTHER NANO-FLOWS PHENOMENA
PublicationIn our work, a further development of the authors model of thermo-chemical flow of fuel, air, oxygen, steam water, species, ionic and electron currents within nano channels and nano-structures of novel devices is presented. Different transport enhancement models are taken into account -among them the most important are: the velocity slip connected with complex external friction, the Darcy mobility and the Reynolds transpiration....
-
Emission of 1.3–10 nm airborne particles from brake materials
PublicationOperation of transport vehicle brakes makes a significant contribution to airborne particulate matter in urban areas, which is subject of numerous studies due to the environmental concerns. We investigated the presence and number fractions of 1.3–10 nm airborne particles emitted from a low-metallic car brake material (LM), a non-asbestos organic car brake material (NAO) and a train brake cast iron against a cast iron. Particles...
-
Synthesis and Biological Evaluation of Acridine/Acridone Analogs as Potential Anticancer Agents
PublicationAcridine and acridone analogues were prepared by Ullmann condensation and then cyclization reaction. As a result of nucleophilic substitution reaction 1-nitro-9-phenoxyacridine or 1-chloro-4-nitro-9(10H)-acridone with the corresponding peptides, the planned acridine derivatives (10a-c, 12, 17-a-d, 19) have been obtained. The cytotoxic activity of the newly obtained analogs were evaluated against melanotic (Ma) and amelanotic (Ab)...
-
Palindromic carbazole derivatives: unveiling their antiproliferative effect via topoisomerase II catalytic inhibition and apoptosis induction
PublicationHuman DNA topoisomerases are essential for crucial cellular processes, including DNA replication, transcription, chromatin condensation, and maintenance of its structure. One of the significant strategies employed in cancer treatment involves the inhibition of a specific type of topoisomerase, known as topoisomerase II (Topo II). Carbazole derivatives, recognised for their varied biological activities, have recently become a significant...
-
ENHANCED EVAPORATION OF THE DROPLETS OF CONDENSATE IN THE ASYMMETRICAL SHOCK WAVE ZONE
PublicationIn the low-pressure part of steam turbine, the state path usually crosses the saturation line in penultimate stages [4,5]. The formation and evolution of these droplets lower the performance of the wet stages of the turbines, and their effects on the efficiency are collectively known as wetness losses [4]. Nowadays, due to work of steam turbines at partial load, process of homogeneous and heterogeneous condensation still is current....
-
The effect of reduced pressure on carbon dioxide flow boiling heat transfer in minichannels
Publication. In the paper presented are the results of the study on the effect of reduced pressure on flow boiling heat transfer data in minichannels as well as conventional ones. That effect renders that most of heat transfer correlations fail to return appropriate results of predictions. Mostly they have been developed for the reduced pressures from the range 0.1-0.3. The special correction has been postulated to the in-house model of flow...
-
Management of low-temperature heat source by ORC aided by additional heat source
PublicationThe presented work is aimed at utilisation of waste heat in the manner to produce electricity in ORC installation. Therefore the precondition of the study was to use the waste heat available in the form of a stream of hot water at 90°C. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. That was the incentive to search for the ways of increasing the temperature of the...
-
Exergetic Analysis of the nCO2PP Cycle with Particular Reference to the Exergy Destruction of Sewage Sludge Due to Gasification
PublicationAn exergy analysis is carried out on the negative CO2 emission gas power plant (nCO2PP), which integrates the process sections of fuel preparation, power generation and carbon capture. Processes of exergy destruction are studied with particular focus on the process in the gasification unit of the fuel preparation section, where a large amount of exergy is destroyed in various chemical reactions from sewage sludge to producer gas...
-
Shape memory thin films of Polyurethane: Does graphene content affect the recovery behavior of Polyurethane nanocomposites?
PublicationThin nanocomposite films of polyurethane have received remarkable attention due to their shape memory properties. As most of the reports focus on the beneficial aspects of the presence of nanofillers such as graphene nanoplatelets (GNPs) introduced into shape memory polymers, some research results reveal the opposite trend. The polyether/polyester-based polyurethane was synthesized through a condensation polymerization and the...
-
Investigation of the Dynamism of Nanosized SOA Particle Formation in Indoor Air by a Scanning Mobility Particle Sizer and Proton-Transfer-Reaction Mass Spectrometry
PublicationTerpenes are VOCs of particular importance, since they are emitted from a wide range of indoor sources and are considered to be precursors of Secondary Organic Aerosol (SOA) formation. It has been proven that SOA particles, especially nanosized ones, pose a threat to human health. In this research, experiments with the application of an environmental chamber and real-time measurement techniques were carried out to investigate in...
-
Structural motifs in the Cu(II), Mn(II) and Zn(II) complexes based on N,N,N-donor dipodal or N,N,N,N-donor tripodal ligands obtained in situ: Synthesis, crystal structures and xanthine oxidase inhibition properties
PublicationA series of four novel transition metal complexes, [Cu(NCS)2L1] (1), [Mn(NCS)2L1] (2) where L1 = bis(1-(3,5-dimethylpyrazolyl)methyl)amine, [Mn(NCS)2L2] (3) and [Zn(NCS)L2]2[Zn(NCS)4] (4) where L2 = tris(1-(3,5-dimethylpyrazolyl)methyl)amine, has been obtained in situ by a one-step, one-pot synthetic path starting from 1-hydroxymethyl-3,5-dimethylpyrazole (L). The isolated complexes were fully characterised by elemental analysis,...
-
Thermodynamic interpretation and prediction of CO2 solubility in imidazolium ionic liquids based on regular solution theory
PublicationRegular solution theory (RST) is the most popular model for the interpretation of the interaction between CO2 and ionic liquids. In the present work, the parameters of this model were determined for the CO2 absorption in eleven imidazolium ionic liquids. The y-intercept (A) of the RST model for the investigated imidazolium liquids increases with increasing temperature whereas the slope (B) remains constant. The values of RST parameters...
-
Compact High Efficiency and Zero-Emission Gas-Fired Power Plant with Oxy-Combustion and Carbon Capture
PublicationReduction of greenhouse gases emissions is a key challenge for the power generation industry, requiring the implementation of new designs and methods of electricity generation. This article presents a design solution for a novel thermodynamic cycle with two new devices—namely, a wet combustion chamber and a spray-ejector condenser. In the proposed cycle, high temperature occurs in the combustion chamber because of fuel combustion...
-
Selected aspects of two-phase flow studies using different visualization techniques in minichannels
PublicationThe subject of the study is to present the possibility of the use of visualization techniques in the researches on two-phase flows, carried out by the authors for many years. These works included as follows: heat transfer during the flow boiling, boiling crises and condensation in flow. The issue of the heat transfer intensification during the flow boiling through the channels of small diameters was analyzed. All this work focused...
-
The influence of crude glycerol and castor oil-based polyol on the structure and performance of rigid polyurethane-polyisocyanurate foams
PublicationIn this work, biopolyol obtained from two types of industrial crops’ processing products: crude glycerol and castor oil was used for preparation or rigid polyurethane-polyisocyanurate foams. Bio-based polyol was obtained via crude glycerol polymerization and further condensation of resulting polyglycerol with castor oil. Rigid polyurethane-polyisocyanurate foams were prepared at partial substitution (0–70 wt.%) of petrochemical...
-
The compositional space of exhaled breath condensate and its link to the human breath volatilome
PublicationBreath analysis is commonly understood to target gaseous or volatile organic compounds (VOCs) for the characterization of different pathologies. Targeted analysis is most effective if a working hypothesis can be based on a plethora of data. The recently published volatilome builds an optimal basis for organizing powerful target sets. However, the origin and pathways of biosynthesis of many VOCs are not known, which complicates...
-
Analysis of Organic Rankine Cycle efficiency and vapor generator heat transfer surface in function of the reduced pressure
PublicationIn the paper presented is analysis of the influence of reduced pressure on efficiency and heat transfer area of vapor generator of Organic Rankine Cycle (ORC) in case of subcritical and supercritical parameters of operation. Compared are two cases of subcritical and supercritical ORC featuring a similar arrangement of heat source supply and heat removal, that is featuring the same temperatures of working fluid before the turbine,...
-
Synthesis of Cyano-Benzylidene Xanthene Synthons Using a Diprotic Brønsted Acid Catalyst, and Their Application as Efficient Inhibitors of Aluminum Corrosion in Alkaline Solutions
PublicationNovel cyano-benzylidene xanthene derivatives were synthesized using one-pot and condensation reactions. A diprotic Brønsted acid (i.e., oxalic acid) was used as an effective catalyst for the promotion of the synthesis process of the new starting xanthene–aldehyde compound. Different xanthene concentrations (ca. 0.1–2.0 mM) were applied as corrosion inhibitors to control the alkaline uniform corrosion of aluminum. Measurements were...
-
Design, synthesis and high antitumor potential of new unsymmetrical bisacridine derivatives towards human solid tumors, specifically pancreatic cancers and their unique ability to stabilize DNA G-quadruplexes
PublicationNew promising unsymmetrical bisacridine derivatives (UAs), have been developed. Three groupsincluding 36 compounds were synthesized by the condensation of 4-nitro or 4-methylacridinone, imi-dazoacridinone and triazoloacridinone derivatives with 1-nitroacridine compounds linked with anaminoalkyl chain. Cytotoxicity screening revealed the high potency of these compounds against severaltumor cell lines. Particularly, imidazoacridinone-1-nitroacridine...
-
Amberlyst-15 catalysed synthesis of novel indole derivatives under ultrasound irradiation: Their evaluation as serotonin 5‑HT2C receptor agonists
PublicationA series of indole based novel Schiff bases was designed as potential agonists of 5‑HT2C receptor that was supported by docking studies in silico. These compounds were synthesized via Amberlyst-15 catalysed condensation of an appropriate pyrazole based primary amine with the corresponding indole-3-aldehyde under ultrasound irradiation at ambient temperature. A number of target Schiff bases were obtained...
-
In vivo imaging of the human eye using a two-photon excited fluorescence scanning laser ophthalmoscope
PublicationBACKGROUND. Noninvasive assessment of metabolic processes that sustain regeneration of human retinal visual pigments (visual cycle) is essential to improve ophthalmic diagnostics and to accelerate development of new treatments to counter retinal diseases. Fluorescent vitamin A derivatives, which are the chemical intermediates of these processes, are highly sensitive to UV light; thus, safe analyses of these processes in humans...
-
Modelowanie procesu wrzenia i kondensacji w rozszerzonym zakresie ciśnień zredukowanych
PublicationNiniejsza rozprawa doktorska ma na celu pokazanie wpływu uwzględnienia ciśnienia zredukowanego w analizowanym modelu opisują-cym współczynnik przejmowania ciepła na zbieżność z danymi eksperymentalnymi.Przedmiotem analizy jest półempiryczny model Mikielewicza w zastosowaniu do danych eksperymentalnych w kanałach konwencjonalnych i o małej średnicy płynów uznanych za perspektywiczne.W ramach realizowanych prac badawczych pozyskano...
-
Experimental Investigation of the Thermal Performance of a Wickless Heat Pipe Operating with Different Fluids: Water, Ethanol, and SES36. Analysis of Influences of Instability Processes at Working Operation Parameters
PublicationIn this study, the influences of different parameters on performance of a wickless heat pipe have been presented. Experiments have been carried out for an input power range from 50 W to 300 W, constant cooling water mass flow rate of 0.01 kg/s, and constant temperature at the inlet to condenser of 10 C. Three working fluids have been tested: water, ethanol, and SES36 (1,1,1,3,3-Pentafluorobutane) with different filling ratios (0.32,...
-
Assessing ecotoxicity and the endocrine potential of selected phthalates, BADGE and BFDGE derivatives in relation to environmentally detectable levels
PublicationThere is no doubt that the subject area of plasticmaterials (e.g., production of epoxy resins or polyesters) is inherently connected to issues concerning bisphenol A (BPA) and its analogues. Unfortunately, much less attention has been given to other compounds, which are also used for the production of these materials. Bisphenol A diglycidyl ether (BADGE) is a synthetic industrial compound obtained by a condensation reaction between...
-
Characterization of recombinant homocitrate synthase from Candida albicans
PublicationLYS21 and LYS22 genes from Candida albicans encoding isoforms of homocitrate synthase (HCS), an enzyme catalyzing the first committed step in the L-lysine biosynthetic pathway, were cloned and expressed as NoligoHistagged fusion proteins in Escherichia coli. The purified gene products revealed HCS activity, i.e. catalyzed the condensation of α-ketoglutarate with acetyl-coenzyme A to yield homocitrate. The recombinant enzymes were purified...
-
Solvothermal growth of {0 0 1} exposed anatase nanosheets and their ability to mineralize organic pollutants. The effect of alcohol type and content on the nucleation and growth of TiO2 nanostructures
PublicationHerein, the series of {0 0 1} exposed anatase nanosheets from HF-assisted solvothermal growth synthesis were obtained. The two-dimensional TiO2 were characterized, including both bulk (XRD, DR-UV–Vis, Mott-Schottky) and surface characteristics (N2 sorption, XPS, SEM) with experimental results compiled with Density Functional Theory (DFT) calculations. The effect of alcohol amount and type was studied, demonstrating the crucial...
-
Tubular House - Form Follows Technology, Concrete Shell Structure with Inner Thermal Insulation
PublicationThe aim of this paper is the theoretical analysis of the possibilities and limitations of using an unconventional technology and the original architectural form stemming from it – the building with external construction and internal insulation. In Central European climatic conditions, the traditional solution for the walls of heated buildings relies on using external thermal insulation. This stems from building physics: it prevents...
-
Golden artefacts, resin figurines, body adhesives and tomb sediments from the pre-Columbian burial site El Caño (Gran Coclé, Panamá): tracing organic contents using molecular archaeometry
PublicationThis research aimed to determine the origin of organic residues from funerary contexts in the El Ca~no settlement (Gran Cocl�e area, Panam�a, Central America) by means of multiple molecular probing techniques (GC-MS of organic solvent extracts and pyrolysis-GC-MS, THM-GC-MS and FTIR of solid samples). The samples include particles of precious resin figurines, fillings of golden objects, tomb sediments, plant exudates from extant...
-
Testing an evaporator operation with a concave manifold, condenser temperature 30, evaporator temperature 70 and preheater temperature 60
Open Research DataThe experiment was conducted to test the evaporator operation. The heat exchanger was equipped with minigeometry (set of 50 parallel minichannels or single minigap). The studies were conducted for various mass flow rate of the working fluid and for various temperatures at the inlet of the evaporator. Accurate information about the test rig, the parameters...
-
Testing an evaporator operation with a bifurcation manifold, condenser temperature 20 and evaporator temperature 85
Open Research DataThe experiment was conducted to test the evaporator operation. The heat exchanger was equipped with minigeometry (set of 50 parallel minichannels or single minigap). The studies were conducted for various mass flow rate of the working fluid and for various temperatures at the inlet of the evaporator. Accurate information about the test rig, the parameters...
-
Testing an evaporator operation with a concave manifold, condenser temperature 30, evaporator temperature 70 and preheater temperature 40
Open Research DataThe experiment was conducted to test the evaporator operation. The heat exchanger was equipped with minigeometry (set of 50 parallel minichannels or single minigap). The studies were conducted for various mass flow rate of the working fluid and for various temperatures at the inlet of the evaporator. Accurate information about the test rig, the parameters...
-
Testing an evaporator operation with a trapezoidal manifold, condenser temperature 90 and evaporator temperature 90
Open Research DataThe experiment was conducted to test the evaporator operation. The heat exchanger was equipped with minigeometry (set of 50 parallel minichannels or single minigap). The studies were conducted for various mass flow rate of the working fluid and for various temperatures at the inlet of the evaporator. Accurate information about the test rig, the parameters...