Filters
total: 2420
filtered: 2069
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: R2B COOPERATION
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublicationThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
The resilient city in architectural engineering education: a joint design studio between Gdańsk and Chalmers universities of technology
PublicationChallenges to society, such as those posed by climate change require a new approach to the education of the engineer-architect. Contemporary solutions should serve future generations and that is why the idea of the resilient city should be discussed and implemented, both in theory and in practice. It is necessary to teach students to design urban structures in such a way that they are resilient to dynamically changing conditions....
-
Marine propeller shaft bearings under low-speed conditions: water vs. oil lubrication
PublicationThe bearings used in shipbuilding, hydropower, and water pumps have undergone a metamorphosis in recent decades. Because of environmental regulations, lubrication with grease or mineral oil is prohibited. Thus, the standard solutions include water-lubricated bearings with polymer bushings or sealed systems lubricated with oil. When properly designed, assembled, and operated, bearings can operate reliably for years. However, specific...
-
Analysis of Failures of High Speed Shaft Bearing System in a Wind Turbine
PublicationDuring the operation of wind turbines with gearbox of traditional configuration, consisting of one planetary stage and two helical stages high failure rate of high speed shaft bearings is observed. Such a high failures frequency is not reflected in the results of standard calculations of bearing durability. Most probably it can be attributed to atypical failure mechanism. The authors studied problems in 1.5 MW wind turbines of...
-
Profile irregularities of turned surfaces as a result of machine tool interactions
PublicationThe paper describes the influence of the machining operation on a surface, which disturbs the projection of the tool profile in the form of its relative movements with respect to the object. The elements of the machine tool undergo constant wear during the machining process, it is therefore important to recognize the effects of their influence on the surface's irregularities. Amplitude-frequency analysis of lateral profiles has...
-
Konkursy studenckie jako narzędzie w określaniu potencjału rewitalizacyjnego miejskich terenów zdegradowanych.
PublicationZgodnie z zasadami prowadzenia działań rewitalizacyjnych określonych w ustawie o rewitalizacji obowiązującej od 9 października 2015 r. oraz horyzontalnych wytycznych w zakresie rewitalizacji w programach operacyjnych na lata 2014-2020 faza przygotowawcza procesu rewitalizacji powinna zawierać wielopłaszczyznowe analizy zakończone wnioskami aplikacyjnymi ujętymi w gminnych programach rewitalizacji obszarów zurbanizowanych. Artykuł...
-
Interplay of hydrogen bonding and aryl-perfluoroaryl interactions in construction of supramolecular aggregates
PublicationThe stacking between aryl and perfluoroaryl units is an important class of the aromatic – aromatic interactions that has attracted rapidly growing interest in recent years. Continuing interest of our group in this subject it had been prepared three new complexes of pentafluorobenzoic acid with benzyl alcohol, 4-methylbenzyl alcohol and 4-tert-butylbenzyl alcohol and in the next step investigated their self-assembly modes by...
-
Corrigendum to “T1 relaxation time callibration in magnetic resonance imaging using nanodiamond phantoms” [Phys Med 94 (2022) S119–S120/EPV029]
PublicationThe authors want to update the incorrect funding information. The correct funding note is: “The authors acknowledge the financial support from Gdańsk University of Technology by the 4/2020/IDUB/III.4.1/Tc grant under the Technetium Talent Management Grants ‘Excellence Initiative – Research University’. The financial support from Gdańsk University of Technology by the 1/2021/IDUB/II.2/Np grant under NEPTUNIUM Enhancing Baltic Region...
-
Tests of bond between concrete and steel bars – literature background and program of own research
PublicationThis article deals with the issue of the bond between concrete and reinforcement. The bond is crucial for reinforced concrete elements because it is possible to transfer forces (stresses) from concrete to the reinforcement. Basic information related to the cooperation of concrete and rebars was recalled in the article. Selected issues concerning theoretical and numerical analysis as well as experiments of the bond phenomenon were...
-
PROPRIETARY SOFTWARE IN TECHNICAL HIGHER EDUCATION
PublicationThe authors present a relatively easy way to extend the quality of education in professional studies (engineering) on major “Geodesy and Cartography”. They indicate the possibility to deepen students’ knowledge by using in the educational process proprietary software enriching education. The authors use their own experiences, results of the cooperation with employers, as well as the effects of scientific research to introduce into...
-
Computational collective intelligence for enterprise information systems
PublicationCollective intelligence is most often understood as a kind of intelligence which arises on the basis of a group (collective) of autonomous unites (people, systems) which is taskoriented. There are two important aspects of an intelligent collective: The cooperation aspect and the competition aspect (Levy 1997). The first of them means the possibility for integrating the decisions made by the collective members for creating the decision of...
-
The role of urban movements in the process of local spatial planning and the development of participation mechanism
PublicationIn civil societies, urban movements are one of the tools in the process of spatial governance. In Poland, urban activism is beginning to develop together with a budding participation in public life. Therefore, there is a need to assess the scope and effects of the urban movements’ actions. The aim of the study was to determine and evaluate their impact on the spatial development in three Polish cities - Poznań, Gdańsk and Gdynia, especially...
-
Political Parties in the Digital World
PublicationThe aim of this report is to outline how digital technologies and digital media are redefining the way political parties fulfill their role as collective platforms for political participation of citizens, e.g. in relation to the parties’ decision-making processes, communication strategies, funding mechanisms, membership, information sharing, etc. and to highlight the existing international standards and good practices in this area....
-
PROPRIETARY SOFTWARE IN TECHNICAL HIGHER EDUCATION
PublicationThe authors present a relatively easy way to extend the quality of education in professional studies (engineering) on major “Geodesy and Cartography”. They indicate the possibility to deepen students’ knowledge by using in the educational process proprietary software enriching education. The authors use their own experiences, results of the cooperation with employers, as well as the effects of scientific research to introduce...
-
Coronas and Domination Subdivision Number of a Graph
PublicationIn this paper, for a graph G and a family of partitions P of vertex neighborhoods of G, we define the general corona G ◦P of G. Among several properties of this new operation, we focus on application general coronas to a new kind of characterization of trees with the domination subdivision number equal to 3.
-
A PROPOSAL OF A DESCRIPTION OF THE OPERATING CONDITIONS OF DIESEL-ELECTRIC LOCOMOTIVES
PublicationThe paper presents a proposal of a description of the operating conditions of diesel-electric locomotives. The proposal is a result of the operational experience and the analysis of the locomotive operation. It constitutes a significant simplification in relation to the descriptions currently used by domestic carriers. The paper also presents examples of analyses of the operating conditions of locomotives using the proposed method.
-
Application of RCD and AFDD in low-voltage electrical installations for protection against fire
PublicationThe paper presents the principles of application of residual current devices (RCDs) in protection against fire. The permissible rated residual operating current of RCDs is discussed. Limitations in the operation of RCDs in this type of protection are indicated. A new type of a protective device against fire – arc fault detection device (AFDD) – is described.
-
The role of the combined nitrogen-sulfur-carbon cycles for efficient performance of anammox-based systems
PublicationThe combined anammox/mixotrophic denitrification process was conducted in two granular sequencing batch reactors (SBRs) during a 200-day operation. Both reactors were fed with synthetic medium, but SBR2 was enriched with additional sulfate (SO4 2 ) which influenced sulfate reduction ammonium oxidation (SRAO) and heterotrophic reduction of SO4 2 by sulfate reducing bacteria. It was hypothesized that the addition of SO4 2 could...
-
Model organizacji ruchu na sieci kolejowej z uwzględnieniem rekuperacji energii
PublicationNa wstępie przeanalizowano aktualny stan wiedzy z zakresu metod wykorzystywania energii z rekuperacji oraz istniejących modeli optymalizujących ich efektywność. Na tej podstawie za główny cel pracy wyznaczono opracowanie metody modyfikacji kolejowego rozkładu jazdy, która doprowadzi do zwiększenia efektywności wykorzystania energii pochodzącej z rekuperacji. W związku z powyższym postawiono tezę, że możliwe jest zwiększenie efektywności...
-
Analysis of the Heating Process of Hydraulic Motors during Start-Up in Thermal Shock Conditions
PublicationConditions that prevail during harsh winters and hot summers pose a serious challenge for machine designers building devices suitable for operation in extreme weather. It is essential for the designers and the users to define the principles and conditions for the safe operation of machines and devices with hydraulic drive in low ambient temperatures. Bearing in mind the above, the author tested the hydraulic motors in thermal shock...
-
Algorytmy wyodrębniania składowych symetrycznych sygnału pomiarowego napięcia w przypadku asymetrii sieci trójfazowej
PublicationW artykule zaprezentowano działanie wybranych algorytmów wykorzystywanych do wyodrębniania składowych symetrycznych z sygnałów pomiarowych napięcia lub prądu w przypadku wystąpienia asymetrii trójfazowej sieci elektroenergetycznej. Weryfikacji działania algorytmów dokonano na podstawie badań symulacyjnych i laboratoryjnych w układzie w którym jako odbiornik zastosowano stojan maszyny asynchronicznej pierścieniowej. Określono wpływ...
-
Processes of enhancing the intelligence of Learning Organizations on the basis of Competence Centers
PublicationThe process of organizational learning and proper knowledge management became today one of the major challenges for the organization acting in the knowledge-based economy. According to the observations of the authors of this paper the demand for formalization of knowledge management processes and organizational learning is particularly evident in research institutions, established either by the universities, or the companies. The...
-
Present state of sewage and wastewater treatment plants in the polish coast of Baltic Sea
PublicationIn the paper the state of art of wastewater management in four zones of Polish Baltic Sea coast: the Vistula Lagoon, the Bay of Gdansk and Bay of Puck, the open sea zone and the Szczecin Lagoon, is discussed. Hydrological characteristics of these four zones as well as characteristics and operation effectiveness of wastewater treatment plants (WWTPs) located there, are presented.
-
Modern control strategy of bidirectional DAB converter with consideration of control nonlinearity
PublicationThis paper focuses on the control strategy for modern universal bidirectional Dual Active Bridge (DAB) converters for microgrid systems. An analysis of the converter equations was carried out, and typical problems related to the influence of dead time on the system operation were discussed. A closed control loop was developed, then tested by simulation and on a laboratory stand.
-
Nonreciprocal Devices Utilizing Longitudinally Magnetized Ferrite Coupled Lines
PublicationThis chapter presents authors’ recent research on the nonreciprocal devices utilizing longitudinally magnetized ferrite coupled line (FCL) junction. The principle of operation of FCL junction is explained and the hybrid techniques of analysis are shown. Numerical and experimental results concerning the nonreciprocal devices utilizing the different configurations of FCL junctions are presented and discussed.
-
Sliding burnishing technology of holes in hardened steel
PublicationNew technology with sliding burnishing of holes with cylindrical surface, made of hardened steel /60 HRC/, is presented in the paper.After burnishing operation on hole diameter 30 mm in satellite gear wheel the surface roughness parameter Ra=0,02-0,04 micrometers was obtained. The method and results of research as technological conclusion are presented.
-
Engendering responsibility in architecture students through real planning for a tram depot in Gdańsk
PublicationApart from technical competencies, the profession of architect requires specific social competencies: understanding the user’s needs, ability to diagnose social problems, negotiating and understanding the impact of construction investments on society and the environment. The architect plays a significant role in the collective effort to create spatial order. This is why it is important to include these social competencies in the...
-
Design and implementation of GEPON architecture in laboratory testbed
PublicationThis paper presents a proposition of GEPON architecture for the didactic purpose. The GEPON architecture is implemented in access networks laboratory testbed. The paper includes a brief description of GEPON standardization, a description of laboratory GEPON equipment architecture and a short presentation of proposed laboratory exercises. The exemplary performance results are included.The proposition of GEPON architecture testbed...
-
New satellite pumps
PublicationStosowanie Maszyn company from Katowice was initiator and originator of newest original high pressure satellite pumps series of types PSM. Construction solution, research and development of these pumps have been conducted by Team of Hydraulics and Pneumatics of Gdansk University of Technology in cooperation with this company within the confines of research project nr R0300103 (source of funds: Ministry of Science and Higher Education)....
-
Development of proximity in cluster organizations
PublicationSustainable development in cluster organizations (COs) is most fully manifested in the synergy effect. In turn, the synergy effect is achieved thanks to the development of proximity among cluster entities. The purpose of the paper is to test two conceptual models reflecting relations between selected dimensions of proximity in cluster organizations. The author reports the findings of a quantitative study conducted in four COs....
-
DESIGN THINKING ORIENTED METHODOLOGY IN GROUP PROJECT AS A STEP IN THE CDIO APPROACH
PublicationRecently much scientific research and industrial work is conducted in multidisciplinary teams, where cooperation between specialists from different areas of expertise is required in order to successfully address the challenging goals. Moreover, in start-up small companies the lack of supporting departments calls for additional multidisciplinary, economic and networking skills known as T-shaped personality. Recognizing these shortcomings...
-
Method of determining the degree of liquid aeration in a variable capacity displacement pump
PublicationThe Author concludes, that there is a possibility of determining a concrete value of the liquid aeration coefficient during the pump operation by finding such value of coefficient with which the increase of torque of mechanical losses is proportional to the indicated torque determined with a fixed value of increase of pressure in the pump working chambers. The fixed value of increase of pressure assumed in searching the liquid...
-
Influence of type of material on performance of hydraulic components in thermal shock conditions
PublicationDuring the start-up of a hydraulic system in low ambient temperatures an incorrect operation may occur. The principles and conditions of safely operating hydraulic driven machines and devices are essential to designers and operators. For this reason the author of this article has conducted a series of tests on hydraulic components and systems in thermal shock conditions (cooled-down components were supplied with hot working medium)....
-
Neural Modelling of Steam Turbine Control Stage
PublicationThe paper describes possibility of steam turbine control stage neural model creation. It is of great importance because wider application of green energy causes severe conditions for control of energy generation systems operation Results of chosen steam turbine of 200 MW power measurements are applied as an example showing way of neural model creation. They serve as training and testing data of such neural model. Relatively simple...
-
Fault Loop Impedance Measurement in Circuits Fed by UPS and Principle of Safety Protection
PublicationThis paper indicates a significant problem of uncertainty of fault loop impedance (FLI) measurement in circuits powered from uninterruptible power supply (UPS) (double-conversion AC-DC-AC). The correctly determined value of this impedance, related to the short-circuit current disconnection time and to the reference value, is one of the most important elements that determines the approval of an electrical installation and its receivers...
-
Modeling of Ice Passage Through Reservoirs System on the Vistula River
PublicationNumerical model was used to assess ice passage through proposed reservoir on the lower Vistula River. Model results were compared with observation on the Vistula River, but because the dam is not constructed yet, the direct comparison was not possible. The study focused on ice movement and accumulation in the reservoir for variety of low flow condition with and without wind effect. Bridge’s piers in the upper part of the reservoir...
-
Influence of Natural Conditions on the Imaging of the Bottom of the Gdańsk Bay by Means of the Side Scan Sonar
PublicationThe interest in underwater resources is the reason for the development of modern hydroacoustic systems, including side sonars, which find numerous applications such as: research of seabed morphology and sediment characteristics, preparation of sea sediment maps, and even in special cases of biocenoses such as sea grass meadows, detection of specific targets at the bottom such as shipwrecks, mines, identification of suitable sites...
-
Numerical Simulations of Hydrodynamic Open-Water Characteristics of a Ship Propeller
PublicationThe paper presents the results of numerical simulations of ship propeller operation bearing the name of Propeller Open Water (POW) Tests. The object of tests was a sample ship propeller (PPTC1), the geometrical and kinematic data of which are available, along with the results of model tests, on the official page of the research centre involved in the measurements. The research aimed at verifying the correctness of results of numerical...
-
Research on the effect of low-sulphur marine fuels on the dynamic characteristics of a CI engine
PublicationThe implementation of low-sulphur, so-called modified marine fuels into operation requires prior labora- tory engine tests to assess the energy, emission and structural effects of their usage. This type of research are carried out on the test bed of a diesel engine as a small-scale physical model that reproduces the adequate design and process (parametric) features of a full-size marine engine. Their key stage is to determine the energy...
-
Implementation of an Adaptive Method for Changing the Frequency Division of the Counter Clock Signal in a Frequency-to-Code Converter
PublicationProcessing physical quantities into an indirect signal is a standard method of transferring information about the measured quantity to the master system, which analyzes the data obtained from the acquisition system. The intermediate signal is very often the voltage, but another transmission medium can be the frequency of the output signal of the “physical quantity-to-frequency” converter. The article presents the implementation...
-
Artificial-Neural-Network-Based Sensorless Nonlinear Control of Induction Motors
Publication -
Rotor broken bar diagnostics in induction motor drive using Wavelet packet transform and ANFIS classification
Publication -
Propagation Characteristics of Partial Discharges in an Oil-Filled Power Transformer
PublicationPower transformers are among the most important assets in the power transmission and distribution grid. However, they suffer from degradation and possible faults causing major electrical and financial losses. Partial discharges (PDs) are used to identify the insulation health status and their degradation level. PDs are incipient, low-magnitude faults caused by localized dielectric breakdown. Those activities emit signals in many...
-
The Effect of Protrusions on the Initiation of Partial Discharges in XLPE High Voltage Cables
PublicationThis paper is focusing on 3D Finite Elements Analysis (FEA) based modelling of protrusions as defects or imperfections in the XLPE high voltage cable. This study is aiming to examine the impact protrusions have on the initiation of partial discharges. Spherical and ellipsoidal protrusions with different sizes at the conductor screen of the high voltage cable is an essential content of this paper. In addition, a spherical gas-filled...
-
How Chain Transfer Leads to a Uniform Polymer Particle Morphology and Prevents Reactor Fouling
PublicationABSTRACT: The effect of adding diethyl zinc as a chain transfer agent during the polymerization of propylene in heptane performed at 80 °C was studied. Although it was expected that the chain transfer would stop after precipitation of the polymer, the polymer molecular weight continued to increase throughout the whole of the polymerization. The presence of diethyl zinc had an additional effect that the polymerizations were devoid...
-
Predictive current controller for sensorless induction motor drive
PublicationPrzedstawiono układ bezczujnikowego sterowania dla napedu z silnikiem klatkowym przy zastosowaniu predykcyjnego regulatora pradu. Zastosowany obserwator adaptacyjny wykazuje dużą odporność na zmiany parametrów silnika. W obserwatorze obliczane są wartości sił elektromotorycznych wykorzystywane w procesie regulacji predykcyjnej pradu silnika. Pokazano wyniki badań symulacyjnych i eksperymentalnych.
-
Nowa, metrologicznie zorientowana sieć neuronowa i metoda diagnostyki obiektów technicznych
PublicationW artykule przedstawiono nową, metrologicznie ukierunkowaną sieć neuronową oraz bazującą na niej metodę diagnostyki uszkodzeń parametrycznych układów analogowych, z klasyfikcją neuronową, o zwiększonej odporności na tolerancje elementów układu i niepewności pomiaru. Zaproponowano sieć neuronową z Dwu-centrowymi Radialnymi Funkcjami Bazowymi (DRFB), której walorem jest lepsze odwzorowanie słownika uszkodzeń, poprawa dokładności...
-
Molecular modelling of a psychrophilic β-galactosidase
PublicationAntarktyczny szczep, gram-ujemnych bakterii, wyizolowanych z przewodu pokarmowego kryla z gatunku Thyssanoessa macrura, sklasyfikowany na podstawie analizy sekwencji nukleotydowej geny 16S rDNA jako Pseudoalteromonas sp. 22b jest producentem wewnątrzkomórkowej zimnolubnej beta-galaktozydazy. Ponieważ enzym ten wykazuje wysoką aktywność katalityczną w zakresie temperatur od 0 do 30 stC, stanowi on atrakcyjny biokatalizator, użyteczny...
-
Validation of Interpolation Algorithms for Multiscale UV-VIS Imaging Using UAV Spectrometer
PublicationIn this study, we present a comparison of popular methods for the interpolation of irregular spatial data in order to determine the applicability of each algorithm for hyperspectral reflectance estimation. The algorithms were benchmarked against a very high-resolution orthoimage from an RGB camera and medium-resolution satellite imagery from Sentinel-2A. We tested five interpolation algorithms: Triangulated Irregular Network (TIN),...
-
Overview of the three multicriteria approaches applied to a global assessment of analytical methods
PublicationCritical and global evaluation of analytical methods should be one of the primary goals in analytical chemistry. A holistic approach, however, requires a look at the varied features: commonly discussed validation criteria, often underrated practical and economic aspects, and typically overlooked compliance with the principles of green analytical chemistry. Carrying out such an assessment in a critical and transparent way is extremely...