Filters
total: 748
filtered: 674
Search results for: POLYSTYRENE CONCRETE
-
REINFORCED CONCRETE SUPPORTING CONSTRUCTION OF THE STADIUM COVER FOR EURO 2012 IN GDAŃSK
PublicationIn the article structural issues that connected with the reinforced concrete supporting construction of the stadium roofing for EURO 2012 in Gdańsk were described. In the first part of the article the concept of stadium foundation were described. In the second the static - strength analysis for two variants fastening together individual foundation elements were made. The two assumed geometrically different concept of foundation...
-
Evaluation of reinforcement corrosion rate in concrete structures by electrochemical noise measurements
PublicationW pracy przedstawiono wyniki obliczeń rezystancji polaryzacyjnej w układzie złożonym z dwóch elektrod (ze stali węglowej oraz elektrody odniesienia), umieszczonych w otulinie betonowej. Szybkość korozji ulega zmianom uzależnionym od stopnia nasiąknięcia betonu roztworem zawierającym jony chlorkowe. Zmiany rezystancji polaryzacyjnej elektrody stalowej oceniane są na podstawie pomiarów prądowego i potencjałowego szumu elektrochemicznego....
-
Experimental and Numerical Investigations of the Effect of Curing Conditions on the Temperature Rise of Concrete
PublicationThis paper presents experimental and numerical studies investigating the impact of three curing conditions on temperature evolution in concrete cubes. The tests were performed on samples of the same volume (3.375 dm3) under different curing conditions: room temperature, insulation boxes, and adiabatic calorimeter. Various cements (Portland cement, Portland composite cement, and blast furnace slag cement) and aggregates (gravel...
-
Influence of the Addition of Recycled Aggregates and Polymer Fibers on the Properties of Pervious Concrete
PublicationThe aim of the study was to check the possibility of reusing aggregate from recycled concrete waste and rubber granules from car tires as partial substitution of natural aggregate. The main objective was to investigate the effects of recycled waste aggregate modified with polymer fibers on the compressive and flexural strength, modulus of elasticity and permeability of pervious concrete. Fibers with a multifilament structure and...
-
RMS-based damage detection in reinforced concrete beams: numerical simulations
PublicationImage-based damage detection methods using guided waves are well known and widely applied approaches in structural diagnostics. They are usually utilized in detection of surface damages or defects of plate-like structures. The article presents results of the study of applicability of imaging wave-based methods in detection in miniscule internal damage in the form of debonding. The investigations were carried out on numerical models...
-
COMPUTER-AIDED CONSTRUCTION AT DESIGNING REINFORCED CONCRETE COLUMNS AS PER EC
PublicationThe article presents the author’s computer program for designing and dimensioning columns in reinforced concrete structures taking into account phenomena affecting their behaviour and information referring to design as per EC. The computer program was developed with the use of C++ programming language. The program guides the user through particular dimensioning stages: from introducing basic data such as dimensions, concrete...
-
A novel formulation of 3D spectral element for wave propagation in reinforced concrete
PublicationThe paper deals with numerical simulations of wave propagation in reinforced concrete for damage detection purposes. A novel formulation of a 3D spectral element was proposed. The reinforcement modelled as the truss spectral element was embedded in the 3D solid spectral finite element. Numerical simulations have been conducted on cuboid concrete specimens reinforced with two steel bars. Different degradation models were considered...
-
High Rise Building: The Mega Sculpture Made Of Steel, Concrete and Glass
PublicationHigh rise building has transformed from providing not only the expansion of floor space but functioning as mega sculpture in the city. The shift away from economic efficiency driven need is only expected to grow in the future. Based on literature studies; after analysing planning documents and case studies, it was examined whether the presumption that gaining the maximum amount of usable area is the only driving factor; or if the...
-
Numerical modeling of GPR field in damage detection of a reinforced concrete footbridge
PublicationThe paper presents a study on the use of the ground penetrating radar (GPR) method in diagnostics of a footbridge. It contains experimental investigations and numerical analyses of the electromagnetic field propagation using the finite difference time domain method (FDTD). The object of research was a reinforced concrete footbridge over a railway line. The calculations of the GPR field propagation were performed on a selected cross-section...
-
Guided wave propagation for assessment of adhesive bonding between steel and concrete
PublicationAdhesive bonding is becoming more increasingly important in joining of structural elements. In civil engineering, there is a growing interest in connection by adhesive bonding in steel-concrete flexural members. This study concerns the guided wave propagation technique applied to condition assessment of an adhesive connection between a steel member and a concrete beam. Various states of degradation were considered by producing...
-
A novel heterogeneous model of concrete for numerical modelling of ground penetrating radar
PublicationThe ground penetrating radar (GPR) method has increasingly been applied in the non-destructive testing of reinforced concrete structures. The most common approach to the modelling of radar waves is to consider concrete as a homogeneous material. This paper proposes a novel, heterogeneous, numerical model of concrete for exhaustive interpretation of GPR data. An algorithm for determining the substitute values of the material constants...
-
Investigations of size effect in tensile fracture of concrete using a lattice model
PublicationArtykuł przedstawia symulacje efektu skali w betonie podczas rozciągania przy zastosowaniu nowego modelu siatkowego. Zbadano wpływ rozkładu i wielkości kruszywa oraz wpływ strefy kontaktu na efekt skali.
-
J. FE modelling of cracks in concrete elements within continuum mechanics.
PublicationW artykule przedstawiono wyniki symulacji rys zakrzywionych w elementach betonowych w warunkach mieszanego sposobu obciążenia. Symulacje wykonano przy zastosowaniu 3 różnych modeli: modelu sprężysto-plastycznego, modelu w ramach mechaniki zniszczeniowej i modelu z rysami obracającymi się.
-
Multi-scale modelling of concrete beams subjected to three-point bending
PublicationW artykule przedstawiono wyniki numeryczne MES dwuskalowego modelowania belek betonowych z nacięciem na poziomie skali makro i mezo. Obliczenia wykonano przy wykorzystaniu modelu degradacji sztywności z nielokalnym osłabieniem. Beton został opisany na poziomie skali mezo jako stochastyczny materiał 3-składnikowy złożony z kruszywa, zaczynu cementowego oraz stref kontaktu. Natomiast na poziomie skali makro został opisany jako materiał...
-
Early prediction of macrocrack location in concrete and other granular composite materials
PublicationHeterogeniczne kruche kompozyty, takie jak beton, ceramika i skały składają się z ziaren połączonych wiązaniami. Pytanie, czy ścieżka pęknięcia, która prowadzi do zniszczenia może być przewidziania na podstawie znanych cech mikrostrukturalnych, a mianowicie łączności wiązań, rozmiaru, energii pękania, wytrzymałości pozostają otwarte. Istnieje wiele kryteriów pęknięć. Najczęściej używane są oparte na postulowanym ekstremum naprężenia...
-
Modeling of capillary fluid flow in concrete using a DEM-CFD approach
PublicationSformułowano połączone podejście do modelowania dwufazowego przepływu wody napędzanego hydraulicznie i kapilarnie w nienasyconym betonie. Proces przepływu analizowano numerycznie w mezoskali w warunkach dwuwymiarowych (2D), łącząc metodę elementów dyskretnych (DEM) z obliczeniową dynamiką płynów (CFD) w warunkach izotermicznych. Przeprowadzono w pełni sprzężone hydromechaniczne testy symulacyjne na małych próbkach betonu o uproszczonej...
-
FE-modelling of strain localization in concrete with coupled elasto-plasticity and damage
PublicationW artykule przedstawiono wyniki numerycznej dla zginania belki betonowej przy zastosowaniu modelu sprężysto-plastycznego, modelu z degradacja sztywności i modelu połączonego sprężysto-plastycznego z degradacją sztywności. Wszystkie modele rozszerzono o długość charakterystyczną mikrostruktury za pomocą teorii nielokalnej.
-
Experimental investigations of size effect in reinforced concrete beams failing by shear
PublicationW artykule omówiono wyniki doświadczalne efektu skali w zbrojonych betonowych belkach niszczących się przez ścinanie. Doświadczenia wykonano dla belek o różnych wymiarach ze zbrojeniem stalowym i bazaltowym. Podczas doświadczeń pomierzono siłę oraz szerokości lokalizacji i rys. Wyniki porównano z modelem skali wg Bazanta.
-
Application of DIC technique to concrete - study on objectivity of measured surface displacements
PublicationArtykuł omawia wyniki pomiarów szerokości lokalizacji odkształceń na powierzchni betonu podczas zginania belek. Wykonano obszerne studia nad obiektywnością pomierzonych przemieszczeń w betonie. Opracowano własna metodę do obliczeń szerokości lokalizacji.
-
Numerical analysis of behaviour of reinforced concrete elements under eccentric compression
PublicationPrzedstawiono wyniki modelowania nośności elementów żelbetowych stosując metodę elementów skończonych. Do opisu betonu zastosowano sprężysto-plastyczne prawo materiałowe wg Druckera-Pragera. Do modelowania stali zbrojeniowej zastosowano sprężysto-plastyczne prawo materiałowe według von Misesa. Obliczenia wykonano dla ścian żelbetowych.
-
A Non-local elasto-plastic model to describe localisations of deformation in concrete
PublicationPrzedstawiono wyniki numerycznej symulacji lokalizacji odkształceń stosując metodę elementów skończonych na bazie nielokalnego prawa sprężysto-plastycznego dla betonu. Prawo wykorzystuje długość charakterystyczną. Obliczenia dla ściskania jednoosiowego pokazały, że wyniki numeryczne nie zależą od siatki MES. Osiągnięto pełną regularyzację problemu brzegowego.
-
Analiza doświadczalna i numeryczna paneli warstwowych z okładzinami z płyty cementowo-magnezjowej i rdzeniem z polistyrenu ekspandowanego
PublicationPanele warstwowe są chętnie stosowane w budownictwie ze względu na wysoki stosunek wytrzymałości do masy, oraz łatwość i szybkość montażu. Idea przekroju warstwowego polega na łączeniu cienkich i wytrzymałych okładzin z lekkim rdzeniem. Dobór materiałów składowych pozwala na swobodę kształtowania cech paneli. W rozprawie opisano panele z okładzinami z płyty cementowo magnezjowej i rdzeniem z polistyrenu ekspandowanego, charakteryzujące...
-
The quality management in precast concrete production and delivery processes supported by association analysis
Publication -
Investigation of Durability Properties for Lightweight Structural Concrete with Hemp Shives Instead of Aggregate
Publication -
Effect of a characteristic length on crack spacing in a reinforced concrete bar under tension
Publication -
Electrochemical investigations of conductive coatings applied as anodes in cathodic protection of reinforced concrete
Publication -
Concrete Compressive Strength Under Changing Environmental Conditions During Placement Processes
PublicationThe technological process of concrete production consists of several parts, including concrete mix design, concrete mix production, transportation of fresh concrete mix to a construction site, placement in concrete framework, and curing. Proper execution of these steps provides good quality concrete. Some factors can disturb the technological process, mainly temperature and excessive precipitation. Changing daily temperature and...
-
Baseline-free debonding detection in reinforced concrete structures by elastic wave propagation
PublicationThe article presents the results of the numerical and experimental analysis concerning wave propagation in reinforced concrete (RC) beams with various extent of debonding between the steel rod and concrete cover. The main aim of the paper was to consider the unsolved research gaps, which considerably limit the application of wave-based methods in practice. The propagation of the flexural wave modes excited and registered on the...
-
FEM and experimental investigations of concrete temperature field in the massive stemwall of the bridge abutment
PublicationThe paper deals with the prediction of early-age concrete temperature of cast-in-place stemwall of the bridge abutment. The considered object is an arch bridge located in Gda´nsk. In the case of massive structures, it is particularly important to not exceed the temperature difference between the core and the concrete surface. Too high temperature gradient generates an increase in thermal stresses, what could be the reason of exceeding...
-
Effect of Particle Size of Fly Ash Microspheres (FAMs) on the Selected Properties of Concrete
PublicationThis paper presents the investigations of selected properties of concrete containing two fractions of fly ash microspheres (FAMs) with grain size up to 200 μm and up to 500 μm. Concrete mixtures with ordinary Portland cement and three substitution rates of cement by FAMs, 1.3%, 2.0%, and 2.6%, were investigated. For all concrete mixes, the constant water–binder ratio (w/b) equal to 0.50 was used. The research program included the...
-
Field Evaluation of High Modulus Asphalt Concrete Resistance to Low-Temperature Cracking
PublicationHigh-modulus asphalt concrete has numerous advantages in comparison to conventional asphalt concrete, including increased resistance to permanent deformations and increased pavement fatigue life. However, previous studies have shown that the construction of road pavements with High Modulus Asphalt Concrete (HMAC) may significantly increase the risk of low-temperature cracking. Those observations were the motivation for the research...
-
Internal imaging of concrete fracture based on elastic waves and ultrasound computed tomography
PublicationThe condition assessment of concrete structures belongs to the greatest challenges of non-destructive testing. Monitoring the fracture process of concrete and detecting cracks at the earliest possible stage is a vital aspect to ensure the safety of civil engineering objects. The use of ultrasound tomography enables imaging the internal structure of a tested element. This study aims at the visualization of fracture damage in concrete...
-
Experiments and calibration of a bond-slip relation and efficiency factors for textile reinforcement in concrete
PublicationTextile reinforcement yarns consist of many filaments, which can slip relative each other. At modelling of the global structural behaviour, interfilament slip in the yarns, and slip between the yarns and the concrete can be considered by efficiency factors for the stiffness and strength of the yarns, and by applying a bond-slip relation between yarns and concrete. In this work, an effective and robust method for calibration of...
-
The influence of texturing of the surface of concrete substrate on its adhesion to cement mortar overlay
Publication -
Experimental Study and Finite Element Modeling of Reinforced Concrete Column Having an Opening
Publication -
Effect of admixtures on fresh grout and two-srtage (pre-placed aggregate) concrete
PublicationPrzedstawiono rezultaty badań doświadczalnych przeprowadzonych dla betonu uzyskanego metodą dwuetapową. Główną przeszkodą szerokiego zastosowania metody betonowania dwuetapowego Polcrete była niska wydajność urządzenia wytwarzającego mikrozaprawę - ultramiksera (UM). Celem przeprowadzonych badań laboratoryjnych było dobranie odpowiednich dodatków i domieszek, które umożliwią wytworzenie mikrozaprawy o takich samych parametrach...
-
The method of analysis of damage reinforced concrete beams using terrestial laser scanning
PublicationThe authors present an analysis of the possibility to assess deformations and mechanisms of destructing bent reinforced concrete beams using the terrestrial laser scanning. As part of the experiments carried out at the Regional Laboratory of Construction of the Concrete Structures Division of the Civil and Environmental Engineering Faculty at Gdansk University of Technology, the reinforced concrete beams were subjected to destruction...
-
Electrochemical investigations of conductive coatings applied as anodes in cathodic protection of reinforced concrete.
PublicationW pracy przedstawiono rezultaty badań elektrochemicznych polimerów przewodzących z pigmentem grafitowym. Wyznaczono parametry elektrochemiczne badanych powłok w trakcie długotrwałej polaryzacji zbrojonego betonu. W oparciu o pomiary impedancyjne wyznaczono parametry elektrochemiczne powłok przewodzących. Wykazano, że badane powłoki mogą być stosowane w ochronie katodowej żelbetu. Badania wykazały, że optymalne stężenie grafitu...
-
Data-Driven Modeling of Mechanical Properties of Fiber-Reinforced Concrete: A Critical Review
PublicationFiber-reinforced concrete (FRC) is extensively used in diverse structural engineering applications, and its mechanical properties are crucial for designing and evaluating its performance. The compressive, flexural, splitting tensile, and shear strengths of FRCs are among the most important attributes, which have been discussed more extensively than other properties. The accurate prediction of these properties, which are required...
-
Characterization of corrosion in reinforced concrete beams using destructive and non-destructive tests
PublicationThe paper presents both non-destructive and destructive experimental tests on steel-reinforced concrete beams subjected to electrochemical corrosion. To examine the condition and behavior of the specimens, destructive tests were carried out, i.e., a three-point bending together with a modulated ultrasonic wave test. In addition, a series of non-destructive experiments were conducted, such as the potential measurement method, low-frequency...
-
Non-uniqueness of fracture parameter choice in simulations of concrete cracking at mesoscale level
PublicationIn the paper a non-uniqueness of fracture parameter choice in simulations of cracking process in plain concrete specimens at mesoscale level under monotonic static loading is analysed. The Finite Element Method is used, where cracks are defined in a discrete way using interface cohesive elements with nonlinear material law including softening. The concrete mesostructure (such as: cement matrix, air voids, aggregates, and Interfacial...
-
Impact of reclaimed asphalt pavement (RAP) on low-temperature properties of asphalt concrete
PublicationHot mix recycling is a practice which enables reusing materials from old asphalt pavements. Current Polish regulations allow usage of RAP only for binder and base courses, and its amount is limited. Asphalt mixtures with RAP material have to fulfil requirements stated for typical asphalt mixtures. The research presents low-temperature properties of twelve different asphalt concretes with RAP material, determined using three-point...
-
The Impact of Homogeneity of High Modulus Asphalt Concrete Layer on Low-Temperature Cracking
PublicationDuring winter season of 2012 numerous transverse cracks developed in high-modulus asphalt concrete (HMAC) base of newly constructed motorway. Pavement cracked both in transverse joint locations and in the area between them. Research which was conducted during investigation of the causes and mechanisms of cracking consisted of: field examination, laboratory testing of specimens cored out of the existing pavement, computational analyses...
-
Application of extended Finite Element Method to cracked concrete elements - numerical aspects
PublicationArtykuł omawia zastosowanie rozszerzonej metody elementów skończonych do zarysowanych elementów betonowych. Obliczenia wykonano dla elementów poddanych zginaniu i mieszanemu ściskaniu - rozciąganiu. Wyniki porównano z doświadczeniami.
-
THE METHOD OF ANALYSIS OF DAMAGE REINFORCED CONCRETE BEAMS USING TERRESTRIAL LASER SCANNING
PublicationThe authors present an analysis of the possibility to assess deformations and mode of failure of R-C beams using terrestrial laser scanning. As part of experiments carried out at the Regional Laboratory of Construction (at Gdansk University of Technology), reinforced concrete beams were subjected to destruction by bending and by shear. The process of press impact on the reinforced concrete beam was recorded using terrestrial laser...
-
DETECTION OF DEBONDING IN STEEL BARS EMBEDDED IN CONCRETE USING GUIDED WAVE PROPAGATION
PublicationThe paper presents a non-destructive diagnostic technique based on guided wave propagation phenomenon used to assess the adhesive bonding between a steel bar and a concrete cover. Double-layered cylindrical specimens with different levels of debonding and its location were investigated. The influence of bonding length on the excitation of multiple modes of longitudinal guided waves was analysed. Numerical simulations of guided...
-
Proceedings of the fib Symposium 2019: Concrete - Innovations in Materials, Design and Structures 2019
PublicationDesigning a concrete mix is a process of synthesizing many components, it is not a simple process and requires extensive technical knowledge. The design process itself focuses on obtaining the required strength of concrete. Very often designing a concrete mix takes into account the need to maintain the proper water-demand and frost-resistance features. The parameters that influence the concrete class most significantly are the...
-
Cost Analysis of Prefabricated Elements of the Ordinary and Lightweight Concrete Walls in Residential Construction
PublicationGlobal economic growth causes an increase in natural resources exploitation, particularly in construction branch. The growing use of electricity contributes to climate change. Therefore, it is necessary to search the solutions, which will allow for reducing natural resources exploitation. One of the many opportunities to do that is the application of the recycled materials. The authors of the given article have analyzed three variants...
-
Machine learning-based seismic response and performance assessment of reinforced concrete buildings
PublicationComplexity and unpredictability nature of earthquakes makes them unique external loads that there is no unique formula used for the prediction of seismic responses. Hence, this research aims to implement the most well-known Machine Learning (ML) methods in Python software to propose a prediction model for seismic response and performance assessment of Reinforced Concrete Moment-Resisting Frames (RC MRFs). To prepare 92,400 data...
-
Fire-induced spalling of ultra-high performance concrete: A systematic critical review
PublicationUltra-high performance concrete (UHPC) is a novel concrete class characterized by a compressive strength of more than 150 MPa. One of the most significant drawbacks of employing UHPC is that is very low permeability owing to its great compactness of dense structure increases the risk of fire-induced spalling. It is challenging for fire safety and structural engineers to predict and analyze this issue due to the lack of widely accepted...