Search
displaying 1000 best results Help
Search results for: ENDOTHELIAL LAYER
-
Application of Msplit method for filtering airborne laser scanning data sets to estimate digital terrain models
PublicationALS point cloud filtering involves the separation of observations representing the physical terrain surface from those representing terrain details. A digital terrain model (DTM) is created from a subset of points representing the ground surface. The accuracy of the generated DTM is influenced by several factors, including the survey method used, the accuracy of the source data, the applied DTM generation algorithm, and the survey...
-
Laser induced formation of copper species over TiO2 nanotubes towards enhanced water splitting performance
PublicationWe proposed fast and scalable route where the ordered TiO2 nanotubes coated with thin copper layers were annealed by the laser beam of 355 nm wavelength at different fluencies in the range of 15–120 mJ/cm2. As a result, copper species are integrated with the titania substrate and the formed material exhibits unique optical absorption bands in the visible range. Moreover, X-ray photoelectron spectroscopy analysis reveals the formation...
-
Analysis of the Surface Stereometry of Alloyed Austenitic Steel after Fibre Laser Cutting using Confocal Microscopy
PublicationThe paper extends the concept of cut edge quality and examines the fibre laser cutting process. A Prima Power Platino Fiber Evo device with a reference speed (RS) of 3500 mm/min was used for laser cutting. In order to analyse the influence of the laser cutting speed on the cut edge quality of X5CrNi18-10 stainless steel sheets, macroscopic studies were conducted on a stereoscopic microscope and surface stereometry on a confocal...
-
Area-Averaged Surface Moisture Flux over Fragmented Sea Ice: Floe Size Distribution Effects and the Associated Convection Structure within the Atmospheric Boundary Layer
Publication -
Properties comparison of rubber and three layer PTFE-NBR-bronze water lubricated bearings with lubricating grooves along full bush circumference based on experimental tests
PublicationWater lubricated bearings have been in industrial use for well over a century. During the last decade their traditional range has been expanded with new, modern products. Despite that fact, certain solutions continue to employ the standard rubber bearing with lubricating grooves located along entire bush circumference. The work presents experimental research conducted on comparable sliding bearings with lubrication grooves along...
-
Expanded graphite assistant construction of gradient-structured char layer in PBS/Mg(OH)2 composites for improving flame retardancy, thermal stability and mechanical properties
Publication -
Wpływ stanu warstwy wierzchniej na mikrostrukturę i właściwości korozyjne stopu SUPERSTON = Influence of the state of surface layer on microstructure and corrosion properties of SUPERSTON alloy
PublicationW artykule przedstawiono rezultaty nadtapiania laserowego w warunkach kriogenicznych stopu SUPERSTON. Dokonano oceny mikrostruktury powierzchni i przekroju stopu SUPERSTON po obróbce laserowej. Określono właściwości stopu, które porównano ze stanem powierzchni po nadtapianiu oraz nadtapianiu i szlifowaniu.
-
Warstwowa ocena epidemiologiczna architektury zakładów opiekuńczo-leczniczych i zakładów gieriatycznych = Layer based epidemiological quality assessment of architecture of care security and geriatric wards
PublicationW artykule opisano możliwość wykorzystania autorskiej metody warstwowej oceny epidemiologicznej (WOE) do oceny potencjalnego ryzyka zakażeń w obiektach przeznaczonych dla osób starszych. Materiał i metody: W celu weryfikacji możliwości użycia metody WOE do oceny zagrożeń w zakresie bezpieczeństwa epidemiologicznego środowiska zbudowanego poddano analizie dostępne źródła literatury związane z obowiązującymi w Polsce wymaganiami...
-
Piotr Jaskuła dr hab. inż.
PeopleI am a Faculty member (Associate Professor, Highway and Transportation Research Department) at the Faculty of Civil and Environmental Engineering, Gdansk University of Technology, Poland).My main research interests include: pavement structures, interlayer bonding, pavement materials, recycling of road pavements, asphalt mixtures, bitumens, construction and maintenance of pavement structures.My lectures at the University include:...
-
The Impact of Material Selection on Durability of Exhaust Valve Faces of a Ship Engine – A Case Study
Publicationwo alloys were used in order to extend the service life of marine engine exhaust valve head. Layers of cobalt base alloys were made of the powders with with chemical composition as follow: the layer marked L12; C-1,55%; Si-1,21%; Cr-29,7%; W-9%; Ni-2%; Mo<0,01%; Fe-1,7%; Co-54,83% and the layer marked N; C-1,45%; Co-38,9%; Cr-24,13%; Ni-10,43%; W-8,75%; Fe-7,64%; Mo-7,56%; Si-2,59%. Base metal was valve steel after heat treatment....
-
Hemangioma, NOS - Male, 48 - Tissue image [6210729587593211]
Open Research DataThis is the histopathological image of SKIN tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Stiffness assessment of the laminate recovered from end-of-life wind turbine blade
PublicationIn the paper the stiffness parameters of the laminate recovered from an aerodynamic shell of a decommissioned wind turbine blade are evaluated. The aim of the work is to assess selected methods for identifying material data, as well as to estimate the level of stiffness degradation during turbine operation. Several practical identification methods are presented and compared. Two concepts of a single laminate layer are considered,...
-
Surface characteristics of glass fibres covered with an aluminum layer after a chemical modification process using secondary ion mass spectrometry (SIMS) and atomic force microscopy (AFM)
PublicationPrzedstawiono wyniki z badań powierzchni modyfikowanych włókien szklanych (przed i po procesie chemicznej modyfikacji ich powierzchni), które są kandydatem na przyszły oryginalny bezmatrycowy materiał odniesienia lotnych analitów etenu (C2H4) metodami spektrometrii mas jonów wtórnych oraz mikroskopii sił atomowych. Badania miały na celu obserwację zmian oraz procesów, jakie zaszły na powierzchni włókien szklanych pokrytych...
-
A Comparative Quantitative Structure-Retention Relationships Study for Lipophilicity Determination of Compounds with a Phenanthrene Skeleton on Cyano-, Reversed Phase-, and Normal Phase-Thin Layer Chromatography Stationary Phases
Publication -
Application of multivariate mathematical-statistical methods to compare reversed-phase thin-layer and liquid chromatographic behaviour of tetrazolium salts in Quantitative Structure-Retention Relationships (QSRR) studies
Publication -
Combined computational-experimental approach to predict blood–brain barrier (BBB) permeation based on “green” salting-out thin layer chromatography supported by simple molecular descriptors
Publication -
Analiza budowy i własności napoiny wykonanej z proszku 1606 ze stopu kobaltu = Morphology and property analyze of the layer made of 1606 powder of cobalt alloy
PublicationW pracy analizowano budowę i zmiany zachodzące w strukturze napawanej laserowo warstwy wykonanej ze stopu kobaltu pod wpływem korozyjnego środowiska gazów spalinowych. Warstwa wykazywała się znaczną niejednorodnością chemiczną i składem różnym od założonego jednakże te nieprawidłowości nie wpłynęły znacząco na jej odporność korozyjną w gorących gazach spalinowych.
-
Influence of the notch rounding radius on estimating the elastic notch stress concentration factor in a laser welded tee joint
PublicationIn recent years an increased interest of industry in sandwich-type metal structures can be observed. These structures consist of thin plates of 2.5 mm in thickness separated by stiffeners of different shapes and forms. Welds joining the plates and stiffeners are made on the outer side of the plates using laser welding technique. A locally focused source of heat causes the plate to melt creating a very narrow and elongated joint....
-
Diagnostics of UV Nanosecond Laser Generated Plasma Plume Dynamics in Ambient Air Using Time-Resolved Imaging
Publication -
<title>Cavity control system advanced modeling and simulations for TESLA linear accelerator and free electron laser</title>
Publication -
Sol–gel glasses with enhanced luminescence of laser dye Rhodamine B due to plasmonic coupling by copper nanoparticles
Publication -
Monolithically p-down nitride laser diodes and LEDs obtained by MBE using buried tunnel junction design
Publication -
Kinetics of molecular decomposition under irradiation of gold nanoparticles with nanosecond laser pulses—A 5-Bromouracil case study
Publication -
Modeling of heat and fluid flow in granular layers using high-order compact schemes and volume penalization method
Publication -
Formation of high-carbon abrasion-resistant surface layers when high-energy heating by high-frequency currents
Publication -
Processing of point cloud data retrieved from terrestrial laser scanning for structural modeling by Finite Element Method
PublicationFinite Element Method is one most popular contemporary method of strength analysis. The method is an advanced method for solving differential equations, based on discretization, which means that area is divided into finite elements. Each finite element has a solution of the equation approximated by specific functions and performing the actual calculations only for nodes of this division. Finite Element Method is widely used in...
-
Examination method of the effect of the incidence angle of laser beam on distance measurement accuracy to surfaces with different colour and roughness
PublicationInterest in the influence of the incidence angle of a laser beam to distance measurements can be seen in many areas of science and technology: geodesy, glaciology, archaeology, machine automation, and others. This paper presents results of measurements of the effect of the incidence angle of a laser beam to distance measurements to the surfaces of different colour and roughness by Topcon's electro-optical total station with an...
-
Influence of Nitriding and Laser Remelting on Properties of Austenitic Stainless Steel Type X10CrNi18-8 and Cavitation Erosion Resistance
PublicationThe paper presents properties of surface layers. Surface layers were obtained by using low temperature glow–discharge nitriding process and laser remelting carried out on austenitic stainless steel type X10CrNi18-8. Investigations were done by using an Ultra Nanoindentation Tester (UNHT) in the Warsaw Institute of Fundamental Technological Research. The influence of the above mentioned...
-
Fiber optic low-coherence Fabry-Pérot interferometer with ZnO layers in transmission and reflective mode: comparative study
PublicationA construction of a low-coherence fiber-optic Fabry-Pérot interferometer using a thin ZnO layer as a reflective surfaces was proposed and examined. In the investigated setup, the ZnO layer of thickness 200 nm were deposited on the face of the standard telecommunication single-mode optical fiber (SMF-28). Measurements of interference signal were performed for the interferometer working in the transmission and reflective mode, as...
-
Integration of Multi-Source Geospatial Data from GNSS Receivers, Terrestrial Laser Scanners, and Unmanned Aerial Vehicles
Publication -
Thermal performance of building envelopes with structural layers of the same density: Lightweight aggregate concrete versus foamed concrete
Publication -
Giant increase of optical transparency for Zn-rich CaxZn1−xO on Al2O3 (0001) grown by pulsed laser deposition
Publication -
Numerical Simulation and Experimental Analysis of Thermal Cycles and Phase Transformation Behavior of Laser-Welded Advanced Multiphase Steel
Publication -
Analysis of the Resistance Change of Chemosensitive Layers to the Presence of Ammonia Vapors under Variable Conditions of Air Temperature and Humidity
Publication -
Tm3+ Doped Multi-Ring Profile Single-Mode Fiber Laser for Application in the Eye-Safe Spectral Range
Publication -
Up-conversion luminescence of Tb^3+ ions in germanate glasses under diode-laser excitation of Yb^3+
Publication -
New trim configurations for laser trimmed thick-film resistors - theoretical analysis, numerical simulation and experimential verification
PublicationW pracy przedstawiono nowe podejście do korekcji rezystorów warstwowych polegające na wytwarzaniu dodatkowego kontaktu w celu rozszerzenia zakresu korekcji i uproszczenia projektowania. Ponadto zaprezentowano nową szybką metodę wyznaczania charakterystyk korekcyjnych a także weryfikację eksperymentalną. Przedstawiono wyniki w postaci zakresów korekcji i względnych przyrostów rezystancji w funkcji kształtu dodatkowego kontaktu oraz...
-
Organic pollutants photodegradation increment with use of TiO2 nanotubes decorated with transition metals after pulsed laser treatment
PublicationAmong various titanium(IV) oxide (TiO2, titania) structures, 1D nanotubes (TiO2 NTs) produced during the two-electrode anodization process, are extensively utilized in sensors or supercapacitors as well as in photo(electro)catalytic water splitting. However, due to wide bandgap and fast electron-hole recombination additional modifications, mostly concerned on materials surface, are required. According to the recent research, TiO2...
-
Evaluating aerial laser scanning for seafloor mapping automation Shallow seabed mapping based on airborne Lidar bathymetry
PublicationThis article presents a novel methodological approach to understand and assess the suitability of ALB for the automatic classification and mapping of the seabed. ALB allows recording of the depth below the Secchi disk.
-
Pulsed Laser Deposition of Bismuth Vanadate Thin Films—The Effect of Oxygen Pressure on the Morphology, Composition, and Photoelectrochemical Performance
PublicationThin layers of bismuth vanadate were deposited using the pulsed laser deposition technique on commercially available FTO (fluorine-doped tin oxide) substrates. Films were sputtered from a sintered, monoclinic BiVO4 pellet, acting as the target, under various oxygen pressures (from 0.1 to 2 mbar), while the laser beam was perpendicular to the target surface and parallel to the FTO substrate. The oxygen pressure strongly affects...
-
Tuning the Laser-Induced Processing of 3D Porous Graphenic Nanostructures by Boron-Doped Diamond Particles for Flexible Microsupercapacitors
PublicationCarbon (sp3)-on-carbon (sp2) materials have the potential to revolutionize fields such as energy storage and microelectronics. However, the rational engineering and printing of carbon-on-carbon materials on flexible substrates remains a challenge in wearable electronics technology. This study demon-strates the scalable fabrication of flexible laser-induced graphene (LIG)-boron doped diamond nanowall (BDNW) hybrid nanostructures...
-
Study on Microstructure and Mechanical Properties of Laser Welded Dissimilar Joint of P91 Steel and INCOLOY 800HT Nickel Alloy
PublicationThis investigation attempts to explore the weld characteristics of a laser welded dissimilar joint of ferritic/martensitic 9Cr-1Mo-V-Nb (P91) steel and Incoloy 800HT austenitic nickel alloy. This dissimilar joint is essential in power generating nuclear and thermal plants operating at 600–650 °C. In such critical operating conditions, it is essential for a dissimilar joint to preserve its characteristics and be free from any kind...
-
The Influence of Drying Temperature on Color Change of Hornbeam and Maple Wood Used as Surface and Inner Layers of Wood Composites
PublicationThe thermal treatment of wood changes its structure due to the degradation of wood polymers (cellulose, hemicellulose and lignin), so the physical properties of wood are either improved or degraded. Color changes apply not only to natural wood, but also to such wood composites for which some amount of glue is used in their construction (e.g., plywood, blockboard or laminboard). This article is focused on the analysis of hornbeam...
-
Locally sculptured modification of the electrochemical response of conductive poly(lactic acid) 3D prints by femtosecond laser processing
PublicationThis manuscript presents an approach to sculpture high electrochemical activity of the 3D printed electrodes with poly(lactic acid) (PLA) matrix and carbon black (CB) filler by femtosecond laser (FSL) ablation. CB-PLA utility for electrochemical applications depends on a surface modification aiming to remove the PLA and uncover the conductive CB. We have discussed how laser pulse energy is critical for such an activation process....
-
Analytical solution of non-stationary heat conduction problem for two sliding layers with time-dependent friction conditions
PublicationIn this article we conduct an overview of various types of thermal contact conditions at the sliding interface. We formulate a problem of non-stationary heat conduction in two sliding layers with generalized thermal contact conditions allowing for dependence of the heat-generation coefficient and contact heat transfer coefficient on time. We then derive an analytical solution of the problem by constructing a special coordinate...
-
Integration of Multi-Source Geospatial Data from GNSS Receivers, Terrestrial Laser Scanners, and Unmanned Aerial Vehicles
PublicationThe analysis based on geospatial data from different measurement systems now constitutes a complex numerical and practical enterprise. The dynamic development of modern technologies enables rapid and precise acquisition of such data. Nonetheless, the diversity of reference systems is today one of the main challenges for their correct interpretation. The combined use of the processed measurement results and archival data in paper...
-
Improvement of Oxygen Electrode Performance of Intermediate Temperature Solid Oxide Cells by Spray Pyrolysis Deposited Active Layers
PublicationIntermediate temperature solid oxide fuel cells oxygen electrodes are modified by active interfacial layers. Spray pyrolysis is used to produce thin (≈500 nm) layers of mixed ionic and electronic conductors: Sm0.5Sr0.5CoO3−δ (SSC), La0.6Sr0.4CoO3−δ (LSC), La0.6Sr0.4Co0.2Fe0.8O3−δ (LSCF), and Pr6O11 (PrOx) on the electrode–electrolyte interface. The influence of the annealing temperature on the electrode polarization (area specific...
-
Laser granulometer as an useful tool for selection of appropriate membranes used in the MIEX®DOC-UF/MF hybrid process
PublicationIn the study, particle size distribution of the MIEX® resin was presented. Such analyses enable to determinate whether presence of fine resin fraction may be the reason for unfavorable membrane blocking during water purification by the hybrid MIEX®DOC-microfiltration/ultrafiltration systems. Granulometric analysis of resin grains using the laser diffraction particle size analyzer (laser granulometer) was carried out as well as...
-
The bismuth vanadate thin layers modified by cobalt hexacyanocobaltate as visible-light active photoanodes for photoelectrochemical water oxidation
PublicationBismuth vanadate thin films deposited using the pulsed laser deposition technique were modified using cobalt hexacyanocobaltate (Cohcc). The 2-step method of Cohcc nanocubes preparation was applied: i) metallic cobalt deposition and ii) cobalt electrooxidation in Co(CN)63− containing electrolyte. The presence of CN stretching vibrations was confirmed by Raman spectroscopy. The energy band gap was equal to 2.5 eV and was estimated...
-
A pilot study to assess an in-process inspection method for small diameter holes produced by Direct Metal Laser Sintering
PublicationPurpose The purpose of this research is to evaluate the geometric quality of small diameter holes in parts printed by DMLS technology. An in-process optical inspection method is proposed and assessed during a pilot study. The influence of the theoretical hole diameter assumed in a CAD system and the sample thickness (hole length) on the hole clearance was analysed. Design/methodology/approach The samples made of two different...