Filters
total: 1777
displaying 1000 best results Help
Search results for: CONJUGATED POLYMERS
-
Materiały stosowane do wytwarzania implantów kości
PublicationMateriały stosowane do wytwarzania implantów kostnych muszą być biokompatybilne, nietoksyczne, bioaktywne oraz wykazywać odpowiednie właściwości mechaniczne, takie jak wytrzymałość na ściskanie, na zginanie oraz sztywność i twardość. Gama stosowanych materiałów jest bardzo szeroka, obejmuje metale, polimery, ceramikę oraz ich kompozyty. Każdy z tych materiałów ma swoje mocne i słabe strony. Praca stanowi przegląd materiałów stosowanych...
-
Waterborne polyesters partially based on renewable resources
PublicationA new experimental approach for preparing biobased, water-soluble polyesters via titanium(IV) n-butoxide-catalyzed bulk polycondensation is presented. In the described method polymers were obtained from isosorbide, maleic anhydride and poly(ethylene glycol). The chemical structure of the synthesized polyesters was confirmed using 2D NMR spectroscopy and by titration methods. Careful analysis of 2D NMR spectra viz. Correlation Spectra...
-
Effect of Ion and Binding Site on the Conformation of Chosen Glycosaminoglycans at the Albumin Surface
PublicationAlbumin is one of the major components of synovial fluid. Due to its negative surface charge, it plays an essential role in many physiological processes, including the ability to form molecular complexes. In addition, glycosaminoglycans such as hyaluronic acid and chondroitin sulfate are crucial components of synovial fluid involved in the boundary lubrication regime. This study presents the influence of Na+, Mg2+ and Ca2+ ions...
-
Introduction to MIP synthesis, characteristics and analytical application
PublicationOne of the trends in analytical chemistry is associated with designing and developing new types of sample preparation techniques, which might significantly increase the efficiency and selectivity of the analytes isolation or/and preconcentration process. One of the most widely employed solutions are selective sorption materials, defined as molecularly imprinted polymers (MIPs), as well as the sorbents with the molecular fingerprint....
-
Tensile validation tests with failure criteria comparison for various GFRP laminates
PublicationThe paper studies the mechanical properties of glass fibre reinforced polymers (GFRP) with various types and orientation of reinforcement. Analyzed specimens manufactured in the infusion process are made of polymer vinyl ester resin reinforced with glass fibres. Several samples were examined containing different plies and various fibres orientation [0, 90] or [+45, –45]. To assess the mechanical parameters of laminates, a series...
-
Shape Memory Polyurethane Materials Containing Ferromagnetic Iron Oxide and Graphene Nanoplatelets
PublicationIntelligent materials, such as memory shape polymers, have attracted considerable attention due to wide range of possible applications. Currently, intensive research is underway, in matters of obtaining memory shape materials that can be actuated via inductive methods, for example with help of magnetic field. In this work, an attempt was made to develop a new polymer composite—polyurethane modified with graphene nanoplates and...
-
Core-Shell Nanoparticles with Hyperbranched Poly(arylene-oxindole) Interiors
PublicationCore-shell type star polymers composed of poly(tert-butyl acrylate) (poly(t-BuA)) arms and 100% hyperbranched poly(arylene-oxindole) interiors were synthesized via the "core-first" method. Atom transfer radical polymerization of t-BuA initiated by 2-bromopropionyl terminal groups of the hyperbranched core was applied for the synthesis of the stars. The resultant star structures were characterized by gel permeation chromatography...
-
Reactive extrusion of biodegradable aliphatic polyesters in the presence of free-radical-initiators: A review
PublicationNowadays, growing attention is being paid to the environment and sustainability, what fully justified research works focused on modification of biodegradable polymers and their composites. In this field of research reactive extrusion seems to be the most promising approach, which fits well to sustainable development strategy. In In the present work, the in-situ modification of biodegradable aliphatic polyesters and the compatibilization...
-
Anna Dołęga prof. dr hab. inż.
People -
THE MELT FLOWABILITY AND TENSILE PERFORMANCE OF POLY (-CAPROLACTONE)/BREWERS’ SPENT GRAIN COMPOSITES AS A FUNCTION OF FILLER MODIFICATION
PublicationNowadays, it is essential to reduce the environmental impact of products and technologies. Such an approach should be highlighted in all research activities. In the case of polymer composites, it can be realized by introducing by-products or waste materials as fillers. An auspicious example of such material is the brewers’ spent grain, the major byproduct of the beer production. Its chemical composition, relatively similar to conventional...
-
The results of the assessment of the degree of deacetylation, antimicrobial activity and cytotoxicity of chitosan materials
Open Research DataDane prezentują wyniki pomiarowe stopnia deacetylacji 5 komerycjnych chitozanów, które przetwarzane dwiema metodami oceniono pod kątem aktywności przeciwdrobnoustrojowej i cytotoksyczności względem modelowej linii fibroblastów mysich L929. Ocenie porównawczej poddano materiały chitozanowe otrzymywane klasyczną metodą rozpuszczania w roztworze...
-
Proposal of New Starch-Blends Composition Quickly Degradable in Marine Environment
PublicationThe aim of this paper was to obtain a quickly degradable in seawater polymer blend as an alternative proposal for classical polymer packaging. For preliminary studies: poly(lactic acid) (PLA), starch, calcium carbonate (CaCO3), gelatin and glycerol were chosen. PLA was pointed out due to its biodegradability and comparable properties to polyethylene or polypropylene. Whereas starch was chosen as abundant, renewable and cheap polymer...
-
DETERMINATION OF THE HYDROXYL NUMBER OF GROUND TIRE RUBBER PARTICLES VIA MODIFIED TEST METHOD FOR ISOCYANATE GROUPS
PublicationNowadays, considering the environmental trends and law regulations associated with the circular economy, it is very important to seek for the methods of by-products and waste utilization. The example of such material, which requires the attention and recycling method is ground tire rubber generated during recycling of post-consumer car tires. It can be introduced into various polymer matrices as a filler, but to enhance its effectivity...
-
Environmental impact and industrial development of biorenewable resources for polyurethanes
PublicationPolyurethanes are among the most developed types of polymers. They are produced from the three primary components, i.e., polyols, low-molecular-weight glycols used as chain extenders, and diisocyanates. Until recently, all these substrates have been obtained via petrochemical processes. A decrease in petroleum-based resources and new ecological trends in chemistry, chemical technology, and materials engineering have generated increasing...
-
The compositional space of exhaled breath condensate and its link to the human breath volatilome
PublicationBreath analysis is commonly understood to target gaseous or volatile organic compounds (VOCs) for the characterization of different pathologies. Targeted analysis is most effective if a working hypothesis can be based on a plethora of data. The recently published volatilome builds an optimal basis for organizing powerful target sets. However, the origin and pathways of biosynthesis of many VOCs are not known, which complicates...
-
Synthesis, characterization, and interactions of single-walled carbon nanotubes modified with doxorubicin with Langmuir–Blodgett biomimetic membranes
PublicationThe synthesis, characterization, and the influence of single-walled carbon nanotubes (SWCNTs) modified with an anticancer drug doxorubicin (DOx) on the properties of model biological membrane as well as the comparison of the two modes of modification has been presented. The drug was covalently attached to the nanotubes either preferentially on the sides or at the ends of the nanotubes by the formation of hydrazone bond. The efficiency...
-
Badania nad nanokompozytami bazującymi na polimerach przewodzących oraz materiałach węglowych w celu zastosowania ich w superkondensatorach
PublicationCelem pracy doktorskiej było uzyskanie nanokompozytu o cechach umożliwiających zastosowanie go jako materiału elektrodowego w kondensatorach elektrochemicznych. Zrealizowano to poprzez połączenie modyfikowanych nanorurek węglowych z polimerem przewodzącym elektronowo- poli(3,4-etyleno-1,4-dioksytiofenem). W założeniu materiał węglowy powinien poprawić właściwości mechaniczne polimeru oraz usprawnić transport jonów. Polimer natomiast...
-
The influence of chemical composition of amide block on the thermal properties and structure of terpoly(ester-b-ether-b-amide) elastomers
PublicationMultiblock terpolymers-(PBT-b-PTMO-b-PA12,10)(n)- constituting the polymer systems, in which one of the three blocks (PBT) does not dissolve in PA12,10 block (hard phase) and, depending on its molecular weight is slightly soluble in PTMO block (soft phase), have been obtained. The DSC method was applied to investigate the thermal properties of these polymers and it was found that PBT block acts as an element that produces stiffness...
-
Chemical and biological stability of polyene macrolides
PublicationThe polyene macrolide antibiotics have been used in an-tifungal therapy since first o f them were discovered in 1950's. Up to now, four polyene macrolides are being used in medical practice, namely amphotericin B, nystatin, candi-cidin and pimaricin.The antifungal activity and mode of ac-tion of polyene macrolides is determined by their structure, chemical and physical properties.The main fragment of polyene...
-
Functionalized polyolefins, synthesis application and industrial relevance
PublicationPolymers play a key role in our modern life full of technical advances and a continuous request for new materials with tailored properties for a low price. Their excellent mechanical properties, good processability, chemical stability and low price make polyolefins the polymers of choice for most commodity and some more specialized applications. As a result, polyolefins account for over 65% of the total world demand of plastic...
-
Fourier transform infrared spectroscopy (FTIR) of pre- PXBS (0 h) and PXBS during the crosslinking process (24 h–288 h)
Open Research DataThe goal of this research was developing biodegradable and biocompatibile xylitol-based copolymers with improved mechanical properties, and investigating the change in their thermal and chemical properties withprogress of the cross-linking process. Using a raw material of natural origin such as xylitol, a prepolymer wasobtained by esterification and...
-
In-situ and ex-situ resistance measurements of polypyrrole film using double-band electrode
PublicationMany in-situ techniques are performed in order to determine the resistance of conducting polymer film. However, the resistance measured in solution can be the combination of polymer resistance and that of other components, such as resistance of supporting electrolyte. Therefore, in this work, the influence of the solution on the resistance of polypyrrole (PPy) film has been studied. PPy film was electrchemically synthesized onto...
-
Characterization of Highly Filled Glass Fiber/Carbon Fiber Polyurethane Composites with the Addition of Bio-Polyol Obtained through Biomass Liquefaction
PublicationThis work aims to investigate the process of obtaining highly filled glass and carbon fiber composites. Composites were manufactured using previously obtained cellulose derived polyol, polymeric methylene diphenyl diisocyanate (pMDI). As a catalyst, dibutyltin dilaurate 95% and Dabco® 33-LV were used. It was found that the addition of carbon and glass fibers into the polymer matrix causes an increase in the mechanical properties...
-
Wpływ syntetycznego polihydroksymaślanu na wybrane właściwosci nowych, otrzymanych z jego udziałem poliuretanów do zastosowań medycznych. cz II. Poliuretany z cykloalifatycznym diizocyjanianem w segmencie sztywnym. Polimery 56(1) 27-34, 2011
Publicationzsyntezowano poliuretany, w ltórych segmenty gietkie SG były zbudowane z telehelicznego, zakończonego obustronnie grupami -OH, ataktycznego polihydroksymaślanu (PHB). Wyniki DSC wskazują, że wprowadzenie PHB zaburza uporządkowanie w obrębie SG i sztywnych, zminejsza sie stopień krystaliczności, zwieksza sie nieco sorpcja wody. Test mikrobiologiczne wytworzonych PUR dowodzą skuteczności sterylizacji plazmą.
-
Tailoring of SiOC composition as a way to better performing anodes for Li-ion batteries
PublicationPolymer derived silicon oxycarbide (SiOC) ceramics are investigated as potential anodes for lithiumion batteries. Different SiOC ceramics are prepared by pyrolysis (1000 °C and 1400 °C under controlled argon atmosphere) of polysiloxanes ceramic precursors. Preceramic polymers are synthesized using the sol–gel method. Phenyltriethoxysilane (PhTES) and methyltriethoxysilane (MTES) have been used as starting precursors and mixed with...
-
Toughness augmentation by fibrillation and yielding in nanostructured blends with recycled polyurethane as a modifier
PublicationIn the present paper, we have carefully investigated the morphology and fracture mechanism of the recycled polyurethane (RPU) /epoxy blend system. The second phase (RPU) added to the epoxy resin has a positive effect on the overall mechanical properties. Interestingly, the recycled polymer has a remarkable effect on the fracture toughness of epoxy resin. The mechanism behind the fracture toughness improvement up on the addition...
-
Mechanical Properties, Microstructure and Surface Quality of Polypropylene Green Composites as a Function of Sunflower Husk Waste Filler Particle Size and Content
PublicationAgricultural waste is a still untapped source of materials that can, in case of proper utilization, significantly improve the sustainability of polymers and their composites. In this work, polymer composites based on isotactic polypropylene were produced incorporating ground sunflower husk in the amount of 10 wt% and 20 wt%. The work’s main objective is to evaluate how preliminary fractioning of this agricultural waste filler affects...
-
GPU-Accelerated LOBPCG Method with Inexact Null-Space Filtering for Solving Generalized Eigenvalue Problems in Computational Electromagnetics Analysis with Higher-Order FEM
PublicationThis paper presents a GPU-accelerated implementation of the Locally Optimal Block Preconditioned Conjugate Gradient (LOBPCG) method with an inexact nullspace filtering approach to find eigenvalues in electromagnetics analysis with higherorder FEM. The performance of the proposed approach is verified using the Kepler (Tesla K40c) graphics accelerator, and is compared to the performance of the implementation based on functions from...
-
Effects of Noncontact Shoulder Tool Velocities on Friction Stir Joining of Polyamide 6 (PA6)
PublicationIn this study, the effects of the traverse and rotational velocities of the noncontact shoulder tool on the heat generation and heated flux during the friction stir joining of high-density polyamide 6 (PA6) polymer were investigated. The computational fluid dynamics (CFD) method was employed to simulate the thermomechanical phenomena during the friction stir joining (FSJ) process of PA6. A developed model was used to consider the...
-
Electrochemical Activity and Electrical Properties of Optimized Polypyrrole Coatings on Iron
PublicationIn this work, electrochemical activity and electrical properties of polypyrrole (PPy) coated iron electrodes have been investigated. PPy film was electrochemically polymerized from sodium salicylate aqueous solution under conditions, which provided an increase of iron corrosion resistance. It was noticed that the pH of the solution and the applied electrode potential range during the study of the polymer properties had an influence...
-
Effective SERS materials by loading Ag nanoparticles into poly(acrylic acid-stat-acrylamide)-block-polystyrene nano-objects prepared by PISA
Publication -
Combination of fumed silica with carbon black for simultaneously improving the thermal stability, flame retardancy and mechanical properties of polyethylene
Publication -
Improved conformational space annealing method to treat β-structure with the UNRES force-field and to enhance scalability of parallel implementation
Publication -
High-resolution microscopy assisted mechanical modeling of ultrafine electrospun network
Publication -
Physical effects of radiation processes in poly(aliphatic/aromatic-ester)s modified with e-beam radiation
Publication -
Novel bio-based thermoplastic poly(ether-urethane)s. Correlations between the structure, processing and properties
PublicationThe main purpose of this work was to analyze the effect of the number of unreacted isocyanate groups and the [NCO]/[OH] molar ratio during the chain extension of a prepolymer during the polymerization process on the structure, processing and selected properties of thermoplastic poly(ether-urethane)s. Three series of novel thermoplastic polyurethanes were obtained via a prepolymer route. Three prepolymers were synthesized from diisocyanate...
-
Phase separation in poly(butylene terephthalate)-based materials prepared by solid-state modification
PublicationThe morphology of a series of poly(butylene terephthalate) (PBT)/fatty acid dimer diol (FADD)-based copolyesters prepared by solid-state modi fi cation (SSM) was studied. It was shown that in copolyesters containing less than 10 wt% FADD two different phases, i.e. a PBT crystalline phase and a PBT-rich amorphous phase, are present. The FADD residues were more or less homogeneously distributed throughout the interlamellar regions....
-
Diamine derivatives of dimerized fatty acids and bio-based polyether polyol as sustainable platforms for the synthesis of non-isocyanate polyurethanes
PublicationA series of environmentally friendly non-isocyanate polyurethanes (NIPUs) were successfully prepared via the polyaddition reaction of bio-based polyether polyol-based cyclic carbonate with diamine derivative of dimerized fatty acids. The syntheses of NIPUs were realized by the three-step method in the absence of toxic solvents and, importantly, the process of carbonation did not require the use of elevated pressure. The effect...
-
Development of nanoscale morphology and role of viscoelastic phase separation on the properties of epoxy/recycled polyurethane blends
PublicationA novel and cost-effective approach towards the modification of epoxy matrix has been developed using recycled polyurethane for the first time without sacrificing any of the intrinsic properties of the resin. Polyurethane, recycled from waste foam by glycolysis process (RPU), was found to be very effective in improving the properties of the thermosetting resin based on Diglycidyl ether of bisphenol-A (DGEBA). The effect of the...
-
Anna Danuta Dettlaff dr inż.
PeopleShe received her Master of Science degree in engineering with honours in 2013 at the Gdańsk University of Technology at the Department of Analytical Chemistry. In 2013-2017, she was a PhD student in the field of Chemical Technology at Faculty of Chemistry. Her doctoral dissertation was entitled “Nanocomposites based on conducting polymer and carbon materials for supercapacitor application”. In 2015, she was doing a three-month...
-
One-dimensional chaos in a system with dry friction: analytical approach
PublicationWe introduce a new analytical method, which allows to find chaotic regimes in non-smooth dynamical systems. A simple mechanical system consisting of a mass and a dry friction element is considered. The corresponding mathematical model is being studied. We show that the considered dynamical system is a skew product over a piecewise smooth mapping of a segment (the so-called base map). For this base map we demonstrate existence of...
-
The XPS studies of the CB-PLA electrodes after different surface treatments (chemical, electrochemical, enzymatic)
Open Research DataThe dataset contains the Xray Photoelectron Spectroscopy results of the studies performed under different conditions of surface activation of the CB-PLA 3D printed electrodes. The activation was performed by hydrolysis in different solvents (DMF, 1M HCl, 1M NaOH), electrolysis in 1M NaOH, enzymatic treatment in polymerase or simultaneous electrolysis...
-
Microwave-assisted preparation of potato starch silicated with silicic acid
PublicationApplication of microwave irradiation for the silication of granular potato starch with silicic acid, and the properties of silicated starch were investigated. Potato starch was esterified on 20 min microwave irradiation of starch with silicic acid, applying the power of 450 or 800Wand, for comparison, on 120 min convectional heating of the reagent blend at 100 ◦C. The degree of esterification and the reaction efficiency did not...
-
Microwave-assisted synthesis of zinc derivatives of potato starch
PublicationZincatated potato starch was prepared in a solid-state, microwave-assisted reaction using generated in situ sodium tetrahydroxozincate [Na2Zn(OH)4]. For comparison, zincatation of starch was also carriedout on convectional heating. Depending on the irradiation conditions, the products of either mono- or crosslinking esterification were formed. Higher power applied at shorter exposition offered products ofmonoesterification, and...
-
Synthesis, chemical structure and properties of cross-linked poly(esterourethanes) based on unsaturated oligo(alkyleneester)diols
PublicationW pracy przedstawiono wyniki badań struktury chemicznej i właściwości nienasyconych oligo(alkilenoestro)dioli oraz syntetyzowanych z ich udziałem poli(estrouretanów). Strukturę oligomeroli oraz poliuretanów ustalono w oparciu o wyniki badań FTIR, NMR, analizę elementarną. Właściwości poli(estrouretanów) określono przez pomiary stabilności termicznej, analizę termomechaniczną oraz obliczenia ciężaru cząsteczkowego łańcuchów polimerowych...
-
Preparation and characterization of genipin cross-linked porous chitosan–collagen–gelatin scaffolds using chitosan–CO2 solution
PublicationNovel porous scaffolds composed of chitosan, collagen and gelatin were prepared by the multistep procedure involving final freeze-drying and characterized. To eliminate the need for residual acid removal from the material after drying, carbon dioxide saturation process was used for chitosan blend formulation. The use of CO2 for chitosan dissolution made the scaffold preparation process more reproducible and economically sustainable....
-
The influence of 4,4'-bis(6-hydroxyhexoxy)biphenyl moieties on properties of polyurethanes based on 4,4'-methylenebis(cyclohexyl isocyanate)
PublicationZsyntetyzowano dwie serie poliuretanów z 4,4'-bis(6-hydroksyheksyloksy)bifenylu (BH6), poliadypinianu 1,6-heksylenu i diizocyjanianu 4,4'-dicykloheksylometanu o udziałach izomeru trans, wynoszącym odpowiednio 16 i 46%. Badano wpływ udziału wagowego (u) małocząsteczkowego diolu(BH6)w odniesieniu do sumy mas komonomerów diolowych, na właściwości uzyskanych poliuretanów metodami DSC, DTA, TGA, mikroskopii polaryzacyjnej, WAXS, DMTA...
-
Effect of preparation method on the properties of potato starch acetates with an equal degree of substitution
Publication -
All-natural bio-plastics using starch-betaglucan composites
Publication -
Properties of retrograded and acetylated starch produced via starch extrusion or starch hydrolysis with pullulanase
Publication