displaying 1000 best results Help
Search results for: TRANSONIC WING
-
Hybrid all-cellulose reinforcement in polypropylene matrix biocomposites for injection moulding - influence of particle geometry and volume fraction on hybrid effect
PublicationThe presented study is focused on evaluation of influence of reinforcement volume fraction and geometry on the occurrence of positive hybrid effect by the hybridisation of man-made cellulose fibres (rayon viscose) with cellulose microparticle fillers applied in polypropylene matrix. Four volume fractions of reinforcement were used at 1:1 combination of short man-made cellulose fibres with cellulose microfillers of different aspect...
-
Influence of Fluid Compressibility and Movements of the Swash Plate Axis of Rotation on the Volumetric Efficiency of Axial Piston Pumps
PublicationThis paper describes the design of a swash plate axial piston pump and the theoretical models describing the bulk modulus of aerated and non-aerated fluids. The dead space volume is defined and the influence of this volume and the fluid compressibility on the volumetric efficiency of the pump is considered. A displacement of the swash plate rotation axis is proposed to reduce the dead space volume for small swash plate swing angles....
-
Solvent Exchange around Aqueous Zn(II) from Ab Initio Molecular Dynamics Simulations
PublicationHydrated zinc(II) cations, due to their importance in biological systems, are the subject of ongoing research concerning their hydration shell structure and dynamics. Here, ab initio molecular dynamics (AIMD) simulations are used to study solvent exchange events around aqueous Zn2+, for which observation in detail is possible owing to the considerable length of the generated trajectory. While the hexacoordinated Zn(H2O)62+ is the...
-
Improvements and new functionalities of UNRES server for coarse-grained modeling of protein structure, dynamics, and interactions
PublicationIn this paper we report the improvements and extensions of the UNRES server (https://unres-server.chem.ug.edu.pl) for physics-based simulations with the coarse-grained UNRES model of polypeptide chains. The improvements include the replacement of the old code with the recently optimized one and adding the recent scale-consistent variant of the UNRES force field, which performs better in the modeling of proteins with the β and the...
-
Induction Generator with Direct Control and a Limited Number of Measurements on the Side of the Converter Connected to the Power Grid
PublicationThe article presents an induction generator connected to the power grid using the AC/DC/AC converter and LCL coupling filter. Three-level inverters were used in the converter, both from the generator side and the power grid side. The algorithm realizing Pulse Width Modulation (PWM) in inverters has been simplified to the maximum. Control of the induction generator was based on the Direct Field-Oriented Control (DFOC) method. At...
-
EVOLUTIONARY MULTI–OBJECTIVE WEATHER ROUTING OF SAILBOATS
PublicationThe paper presents a multi-objective method, which optimises the route of a sailboat. The presented method makes use of an evolutionary multi-objective (EMO) algorithm, which performs the optimisation according to three objective functions: total passage time, a sum of all course alterations made during the voyage and the average angle of heel. The last two of the objective functions reflect the navigator’s and passenger’s comfort,...
-
Fast-response optoelectronic detection of explosives’ residues from the nitroaromatic compounds detonation: field studies approach
PublicationWe are presenting an application of optoelectronic nitrogen dioxide (NO2) analyzer based on cavity enhanced absorption spectroscopy in the detection of traces of explosives after detonation. It has been shown that the analyzer using blue-violet laser is able to detect explosive residues after the detonation of various amounts of nitroaromatic compounds (75g-1kg) with higher efficiency than the HPLC soil sample testing equipment,...
-
Vacuum ultraviolet photoionization and ionic fragmentation of the isoxazole molecules
PublicationThe photofragmentation of the isoxazole molecules producing ionized atomic and molecular fragments was investigated in the photon energy range of 9e32 eV, using synchrotron radiation excitation combined with ion time-of-flight spectrometry. Twenty-one well resolved cations were identified in the mass spectra of the isoxazole, and their appearance energies were determined. The yield curves of these cations were obtained in the photon...
-
Hybrid Finite Element Method Development for Offshore Structures’ Calculation with the Implementation of Industry Standards
PublicationIn the design process of offshore steel structures, it is typical to employ commercial calculation codes in which simulation and evaluation of results are performed on the basis of the available standards (e.g. API, DNV, Lloyds). The modeling and solution rely on finite element methods and cover the simulation of the structure’s properties along with the influence of the marine environment – sea currents, wave and wind loading,...
-
Simplified approach to assess the dynamic response of a container ship subjected to bow slamming load
PublicationSimplified approach to assess the dynamic response of a container ship subjected to the bow slamming load, resulting in a transient vibratory response, typically called a 'whip-ping', is presented. The accurate numerical modelling is very complex and involves cou-pling of the hydrodynamic and structural solution at every time step, leading to huge com-putational and workload cost. Thus, the one-way coupling methodology is adopted,...
-
Elucidating the impact of enzymatic modifications on the structure, properties, and applications of cellulose, chitosan, starch and their derivatives: a review
PublicationPolysaccharides, as one of the most prominent natural biopolymers, display numerous biological activities and industrial applications. Nevertheless, some polysaccharides lack biological properties or display weak biological activities. Besides, practical usages of polysaccharides still remain challenging because of their poor solubility and inappropriate hydrophilic/hydrophobic balance. Hence, enzymatic or chemical modifications...
-
Experimental and Numerical Study on Mechanical Characteristics of Aluminum/Glass Fiber Composite Laminates
PublicationThe fiber-metal composites made of aluminum sheets and glass fibers reinforced with a polyester resin as the matrix were studied. The composites were prepared by hand lay-up method. Some aspects of manufacturing affecting the composite behavior were considered. In particular, the influences of the arrangement of layers and their number on the mechanical and physical properties of composites with ten different compositions were...
-
Multiacces quantum communication and product higher rank numerical range
PublicationIn the present paper we initiate the study of the product higher rank numerical range. The latter, being a variant of the higher rank numerical range, is a natural tool for study- ing a construction of quantum error correction codes for multiple access channels. We review properties of this set and relate it to other numerical ranges, which were recently introduced in the literature. Further, the concept is applied to the construction...
-
Inwestycje alternatywne i ich korelacja z rynkiem inwestycji tradycyjnych
PublicationW referacie przedstawiono pojęcie oraz atrybuty inwestycji alter-natywnych w kontekście funkcjonowania inwestycji tradycyjnych. Wy-znaczone zostały również współczynniki korelacji liniowej Pearsona po-między stopami zwrotu inwestycji tradycyjnych (reprezentowanymi przez indeksy WIG, WIG20, mWIG40 oraz sWIG80) i alternatywnych (reprezentowanymi przez złoto, srebro, platynę, pallad i ropę naftową). W ten sposób zbadano, czy wybrane...
-
Wpływ ryzyka finansowego na aktywa gospodarstw domowych w Polsce
PublicationNiezależnie od uzyskiwanych dochodów każde gospodarstwo domowe jest uczestnikiem rynku finansowego. Z każdym wykorzystywanym przez niego instrumentem finansowym wiąże się określone ryzyko finansowe. Ryzyko to może wpłynąć na wzrost bądź spadek aktywów finansowych tych podmiotów, niezależnie od podejmowanych przez niego działań. Celem niniejszego opracowania jest określenie podstawowych rodzajów ryzyka związanego z obecnością gospodarstw...
-
In vivo phytotoxic effect of yttrium-oxide nanoparticles on the growth, uptake and translocation of tomato seedlings (Lycopersicon esculentum)
Publication -
Application of persulfate-based oxidation processes to address diverse sustainability challenges: A critical review
PublicationOver the past years, persulfate (PS) is widely applied due to their high versatility and efficacy in decontamination and sterilization. While treatment of organic chemicals, remediation of soil and groundwater, sludge treatment, disinfection on pathogen microorganisms have been covered by most published reviews, there are no comprehensive and specific reviews on its application to address diverse sustainability challenges, including...
-
Through the looking-glass of the grazing bifurcation
Publication -
Topological behavior mimicking ethylene–hexene copolymers using branched lactones and macrolactones
PublicationPolyolefins are of paramount importance in the world of polymers due to their technological and economic potential.1 However, their nonpolar character significantly restricts the compatibility and adhesion properties, which consequently limits their versatility. Moreover, an intensified demand for materials from renewable resources can also become a problematic venture for the current polyolefin industry.2 Although Braskem and...
-
Improving Thermal Insulation Properties for Prefabricated Wall Components Made of Lightweight Aggregate Concrete with Open Structure
PublicationPorous concrete is commonly used in civil engineering due to its good thermal insulation properties in comparison with normal concrete and high compression strength in comparison with other building materials. An extremely porous concrete, called ‘lightweight aggregate concrete with open structure’ (LAC), is used in some German plants to produce prefabricated wall components. They are used mainly in hall buildings, e.g. supermarkets....
-
Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests
PublicationsettingsOrder Article Reprints Open AccessArticle Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests by Janusz Telega 1,*ORCID,Piotr Kaczynski 1ORCID,Małgorzata A. Śmiałek 2ORCID,Piotr Pawlowski 3ORCID andRyszard Szwaba 1ORCID 1 Institute of Fluid Flow Machinery Polish Academy of Sciences (IMP PAN), Fiszera 14, 80-231 Gdansk, Poland 2 Faculty of Mechanical Engineering and Ship Technology, Institute of Naval...
-
Medium-sized cyclic bis(anisylphosphonothioyl)- disulfanes and their corresponding cyclic sulfane-structures and most characteristic reactions
PublicationCyclic 8-, 9-, 10-, and 12-membered bis(anisylphosphonothioyl)disulfanes were synthesized. Next, structurally related 7 to 9-membered cis and trans sulfanes were isolated as a result of sulfur atom extrusion from the parent cyclic disulfanes. The results of the desulfurization of the disulfanes were compared to the results obtained for desulfurization of the respective bis(anisylphosphodithioates). Cyclic disulfanes predominantly...
-
Real-Time Basic Principles Nuclear Reactor Simulator Based on Client-Server Network Architecture with WebBrowser as User Interface
PublicationThe real-time simulator of nuclear reactor basic processes (neutron kinetics, heat generation and its exchange, poisoning and burn- ing up fuel) build in a network environment is presented in this paper. The client-server architecture was introduced, where the server is a pow- erful computing unit and the web browser application is a client for user interface purposes. The challenge was to develop an application running under the...
-
A socially responsible university - an attempt to approach the system
PublicationIt is the author's thesis that social responsibility of university is an integrated system of both knowledge management (KM), quality management (QM) and organizational development (OD) processes. The author determined that the university "bond" is an institutional culture (IC). An integrated system is the way to create university an open system co-operated and co-opetited with stakeholders. The stakes are high in game - both students...
-
Efektywność skrępowania betonu w grubościennych słupach typu Concrete-Filled Steel Tube o przekroju kołowym
PublicationW słupach typu CFST w stanie granicznym dochodzi do zwiększenia wytrzymałości betonu rdzenia na skutek jego skrępowania. Zaistnienie tego zjawiska zależy od wielu czynników. Jednym z najważniejszych z nich jest sztywność obwodowa płaszcza stalowego. Jej wpływ na efektywność wzrostu wytrzymałości betonu rdzenia przebadano eksperymentalnie na grupie 48 grubościennych słupów CFST. Wykazano, że nadmierne zwiększanie grubości płaszcza...
-
Copper and cobalt co-doped ceria as an anode catalyst for DIR-SOFCs fueled by biogas
PublicationThe nanocrystalline compounds of Co and Cu co-doped ceria (with up to 20 mol.% of dopants) were fabricated by the reverse microemulsion synthesis method. They were deposited in a form of layers on the surface of SOFC anode in an aim to act as electrochemically active materials for biogas reforming process. Fourier Transformed Infrared Spectroscopy was used to analyze a composition of outlet gases simultaneously with the tests of...
-
In situ study of a composition of outlet gases from biogas fuelled Solid Oxide Fuel Cell performed by the Fourier Transform Infrared Spectroscopy
PublicationThe purpose of this study was to develop a method and software based on the Fourier Transform Infrared Spectroscopy for the in-situ, quantitative analysis of the composition of outlet gases from Solid Oxide Fuel Cell (SOFC). The calibration procedure performed at the beginning of the experiment indicated a polynomial dependence between the concentration of a calibrating gas (CO, CO2, CH4) and the corresponding integrated absorbance in...
-
Modification of Ground Tire Rubber—Promising Approach for Development of Green Composites
Publication -
Ceria Based Protective Coatings for Steel Interconnects Prepared by Spray Pyrolysis
PublicationStainless steels can be used in solid oxide fuel/electrolysis stacks as interconnects. For successful long term operation they require protective coatings, that lower the corrosion rate and block chemical reactions between the interconnect and adjacent layers of the oxygen or the hydrogen electrode. One of the promising coating materials for the hydrogen side is ceria. Using standard sintering techniques, ceria sinters at around...
-
Corrosion Study of Ceria Protective Layer Deposited by Spray Pyrolysis on Steel Interconnects
PublicationSingle fuel cells and electrolysis cells are assembled into stacks using interconnects in order to increase power and gas production capacity. The most common choice for the interconnect material is stainless steel. It has good electrical and mechanical properties and is also cost effective. One of the problems when using steel is the formation of a thermally grown oxide scale during use which has a lower electrical conductivity...
-
The influence of synthesis method on the microstructure and catalytic performance of Y 0.07 Sr 0.93 Ti 0.8 Fe 0.2 O 3-δ in synthetic biogas operated solid oxide fuel cells
PublicationThe Y0.07Sr0.93Ti0.8Fe0.2O3-δ (YSTF) material was fabricated using three different synthesis methods: modified polymer precursor method (MPP), Pechini method and a solid state reaction method. It was applied as an anode catalytic material for biogas reforming in solid oxide fuel cells. Clear differences in the microstructure of fabricated catalytic layers were found, mainly with respect to a grain size and distribution of grains....
-
Collision Strengths of Astrophysical Interest for Multiply Charged Ions
PublicationThe electron impact excitation and ionization processes are crucial for modeling the spectra of different astrophysical objects, from atmospheres of late-type stars to remnants of supernovae and up to the light emission from neutron star mergers, to name just a few. Despite their signifi- cance, however, little is known quantitatively about these processes for low- and medium-impact energies of, say, Ekin . 5000 eV of the free...
-
High-performance anode-supported solid oxide fuel cells with co-fired Sm0.2Ce0.8O2-δ/La0.8Sr0.2Ga0.8Mg0.2O3−δ/Sm0.2Ce0.8O2-δ sandwiched electrolyte
PublicationIn this study, intermediate-temperature solid oxide fuel cells (IT-SOFCs) with a nine-layer structure are constructed via a simple method based on the cost-effective tape casting-screen printing-co-firing process with the structure composed of a NiO-based four-layer anode, a Sm0.2Ce0·8O2-δ(SDC)/La0·8Sr0.2Ga0.8Mg0·2O3−δ (LSGM)/SDC tri-layer electrolyte, and an La0·6Sr0·4Co0·2Fe0·8O3-δ (LSCF)-based bi-layer cathode. The resultant...
-
Effects of Ni-NCAL and Ni–Ag electrodes on the cell performances of low-temperature solid oxide fuel cells with Sm0.2Ce0·8O2-δ electrolyte at various temperatures
PublicationThree low-temperature solid oxide fuel cells are built using Sm0.2Ce0·8O2-δ (SDC) as the electrolyte. Cell A is symmetrical and features Ni–LiNi0.8Co0·15Al0·05O2 (Ni–NCAL) electrodes, Cell B comprises a Ni–NCAL anode and a Ni–Ag cathode, and Cell C is fabricated using a Ni–NCAL cathode and a Ni–Ag anode. The ohmic resistance and polarization resistance (Rp) of Cells B and C are significantly higher than those of Cell A. The reduction...
-
Tuning Electrochemical Performance by Microstructural Optimization of the Nanocrystalline Functional Oxygen Electrode Layer for Solid Oxide Cells
PublicationFurther development of solid oxide fuel cell (SOFC) oxygen electrodes can be achieved through improvements in oxygen electrode design by microstructure miniaturisation alongside nanomaterials implementation. In this work, improved electrochemical performance of an La0.6Sr0.4Co0.2Fe0.8O3-d (LSCF) cathode was achieved by the controlled modification of the La0.6Sr0.4CoO3-d (LSC) nanocrystalline interlayer introduced between a porous...
-
Characteristics of La 0.8 Sr 0.2 Ga 0.8 Mg 0.2 O 3-δ -supported micro-tubular solid oxide fuel cells with LaCo 0.4 Ni 0.6-x Cu x O 3-δ cathodes
PublicationIn this study, micro-tubular solid oxide fuel cells (T-SOFCs) with extruded La0.8Sr0.2Ga0.8Mg0.2O3-δ (LSGM) electrolyte as the mechanical support and LaCo0.4Ni0.6O3-δ (LCNO) or LaCo0.4Ni0.4Cu0.2O3-δ (LCNCO) as cathodes were prepared and characterized. Partial substitution of Cu for the Ni-ion positions in the LCNO lattices was found to significantly enhance the densification and accelerate the grain growth. The porosity-corrected...
-
Preparation of methanation catalysts for high temperature SOEC by β-cyclodextrin-assisted impregnation of nano-CeO2 with transition metal oxides
PublicationThe aim of this work was to prepare and examine the catalytic activity of nanometric CeO2 decorated with transition metal oxides – Ni, Co, Cu, Fe and Mn – towards a high-temperature methanation process under SOEC CO2/H2O simulated co-electrolysis conditions. Samples were prepared using the wet impregnation method via the conventional process and with the addition of native cyclodextrin. The influence of β-cyclodextrin (βCD) onto...
-
Degradation of bisphenol S – a contaminant of emerging concern - by synergistic ozone and percarbonate based AOP
PublicationDegradation of bisphenol S was studied using ozone activated by sodium percarbonate and the effectiveness of optimized process was compared with the peroxone process. The influence of several factors including sodium percarbonate concentration, ozone dose, pH, and water matrix were investigated. A synergetic coefficient of 3.84 was achieved for the combination of sodium percarbonate and ozone, confirming the effectiveness of this...
-
Expedited Machine-Learning-Based Global Design Optimization of Antenna Systems Using Response Features and Multi-Fidelity EM Analysis
PublicationThe design of antenna systems poses a significant challenge due to stringent per-formance requirements dictated by contemporary applications and the high com-putational costs associated with models, particularly full-wave electromagnetic (EM) analysis. Presently, EM simulation plays a crucial role in all design phases, encompassing topology development, parametric studies, and the final adjustment of antenna dimensions. The latter...
-
Numerical Modelling of Structures with Uncertainties
PublicationThe nature of environmental interactions, as well as large dimensions and complex structure of marine offshore objects, make designing, building and operation of these objects a great challenge. This is the reason why a vast majority of investment cases of this type include structural analysis, performed using scaled laboratory models and complemented by extended computer simulations. The present paper focuses on FEM modelling...
-
Biopolymers and Their Composites for Drug Delivery: A Brief Review
PublicationIn recent years, excipient development has become a core area of research in pharmaceutical drug delivery because it influences the formulation development and drug delivery process in various ways. Polymeric drug delivery systems have been of great interest for controlled delivery as they show the great advantage in drug delivery systems because of optimized drug loading and releasing property. Then, the side effects of synthetic...
-
Reduced-cost surrogate modelling of compact microwave components by two-level kriging interpolation
PublicationFull-wave electromagnetic (EM) analysis is a versatile tool for evaluating the performance of high-frequency components. Its potential drawback is its high computational cost, inhibiting the execution of EM-driven tasks requiring massive simulations. The applicability of equivalent network models is limited owing to the topological complexity of compact microstrip components because of EM cross-coupling effects. Development of...
-
Basic sensitivity analysis of a telecommunication tower complementing standard reinforcement design process
PublicationThis paper presents straightforward sensitivity assessment of a telecommunication tower. The analysis is set toidentify the elements of the tower which may be reinforced with the greatest structural advantage. As current expertopin ions on structural redesign of similar structures due to a planned addition of extra loads are mainly based ondeterministic computations or engineering intuition,...
-
Multi-mode vibronic interactions in the five lowest electronic states of the fluorobenzene radical cation
PublicationThe multi-mode vibronic interactions between the five lowest electronic states of the fluorobenzene radical cation are investigated theoretically, based on ab initio electronic structure data, and employing the linear vibronic coupling model. Low-energy conical intersections, and strong vibronic couplings are found to prevail within the set of X-A and B-C-D cationic states, while the interactions between these two sets of states...
-
Optimal Placement of Phasor Measurement Unit in Power System using Meta-Heuristic Algorithms
PublicationThe phasor measurement units (PMUs) play an important and vital role in power system monitoring and controlling, since they provide the power system phasors stamped with a common real time reference through a global positioning system (GPS). Indeed, from economical point of view it is not possible to set PMUs in all system buses due to the high cost and the requirement of more complex communication...
-
TASTE QUALITIES ESTIMATION BY TASTE SENSE AND ELECTROCHEMICAL SENSORS
PublicationThe principles of taste sense and kinds of tastes (sweet, salty, sour, bitter, umami and fat) have been described. Food quality estimation by taste sense: organoleptic testing and sensory analysis has been presented. The principle of operation of potentiom etric sensor composed of several Ion Selective Electrodes or All Solid State Electrodes with polymeric membranes and macromolecular chemical compounds sensitive to substances...
-
Characterization and properties of LDPE/(ground tire rubber)/crosslinked butyl rubber blends
PublicationIn recent years, interest in used rubber recycling, mainly focusing on the utilization of end-of-life tires, has heightened. This interest, is owing to the activities related to environmental protection and economic factors, which both stimulate companies to reuse the high-quality rubber present in ground rubber scrap. In this study, the application of crosslinked butyl rubber in thermoplastic compositions of low-density polyethylene...
-
Determination of parent and methylated polycyclic aromatic hydrocarbons in water samples by dispersive liquid–liquid microextraction–two dimensional gas chromatography–time-of-flight mass spectrometry
PublicationPolycyclic aromatic hydrocarbons (PAHs) are contaminants frequently found in environmental waters. Owing to their toxic effects, it is important to develop analytical methodologies that allow their fast and reliable determination. Dispersive liquid–liquid microextraction (DLLME) allows a quick extraction of analytes with little organic solvent consumption. The best results regarding sample preparation are obtained when 40 mL of...
-
A novel luminescent chemical sensor for the determination of Pb 2+ and Cu 2+ ions
PublicationSilica xerogel surface grafted with aminopropyl (PrNH2) groups was additionally treated by cetyltrimethylammonium bromide (CTAB) surfactant and ascorbic acid (asc) in alkaline solution. This material symbolized as SiO2-PrNH2-CTAB/asc, proved to be a stable luminescent material, exhibited an emission band peaked at 393 nm under excitation wavelength 335 nm. Time evolution of the band intensity suggests changes of defect concentration...
-
MEMS based voice message system for elevators
PublicationW artykule przedstawiono implementację systemu głosowych komunikatów w windach. Prezentowany system posiada unikalną cechę polegającą na tym, że do działania nie potrzebuje połączenia z systemem sterującym windy. Zasilany z baterii lub akumulatorów może być zamontowany w ścianie windy, wymaga tylko prostej kalibracji. System oparty jest na akcelerometrach MEMS dokonujących pomiaru przeciążeń w kabinie windy. W artykule przedstawiono...