Filtry
wszystkich: 765
wybranych: 577
Wyniki wyszukiwania dla: DESIGN OF EXPERIMENT
-
Estimation of DC motor parameters using a simple CMOS camera
PublikacjaDifferent components of control systems for mobile robots are based on dynamic models. In low-cost solutions such a robot is wheeled and equipped with DC motors, which have to be included in the model of the robot. The model is fairly simple but determination of its parameters needs not to be easy. For instance, DC motor parameters are typically identified indirectly using suitable measurements, concerning engine voltage, current,...
-
Improvement of the Chimney Effect in Stack Ventilation
PublikacjaThe article is focused on the airflow in a ventilation system in a building. The work examines the methods which enhance the chimney effect. In this paper, three cases with different chimneys were analyzed for the full-scale experiment. These cases were characterized by different geometrical and material parameters, leading to differences in the intensity of the ventilation airflow. The common denominator of the cases was the room...
-
Analysis of Failure Mechanism in Joints with Positive Eccentricity in CFS Truss
PublikacjaThe paper presents studies concerning the load-bearing capacity of truss joints with a positive eccentricity resulting from the arrangement of geometric members and the failure mechanisms observed in the joints. Based on the previously conducted experimental study, a numerical model of the tested fragment of the CFS truss with eccentricity in the joint was created and validated. All structural details of the tested truss and the...
-
Phage Therapy—Challenges, Opportunities and Future Prospects
PublikacjaThe increasing drug resistance of bacteria to commonly used antibiotics creates the need to search for and develop alternative forms of treatment. Phage therapy fits this trend perfectly. Phages that selectively infect and kill bacteria are often the only life-saving therapeutic option. Full legalization of this treatment method could help solve the problem of multidrug-resistant infectious diseases on a global scale. The aim of...
-
Will NILM Technology Replace Multi-Meter Telemetry Systems for Monitoring Electricity Consumption?
PublikacjaThe estimation of electric power utilization, its baseload, and its heating, light, ventilation, and air-conditioning (HVAC) power component, which represents a very large portion of electricity usage in commercial facilities, are important for energy consumption controls and planning. Non-intrusive load monitoring (NILM) is the analytical method used to monitor the energy and disaggregate total electrical usage into appliance-related...
-
Anaerobic consortia mediate Mn(IV)-dependent anaerobic oxidation of methane
PublikacjaManganese-dependent anaerobic oxidation of methane (Mn-AOM) is a major methane sink and vital to mitigating global warming. However, it is difficult for microorganisms to mediate electron transfer between the hardly dissolved CH4 and insoluble Mn(IV) minerals, leading to poor understanding of species mediating Mn-AOM. This study successfully enriched an anaerobic consortium mediating AOM driven by Mn-dependent respiratory growth,...
-
Experimental and numerical investigation of mercury removal from flue gas by sorbent polymer composite
PublikacjaThis paper presents an experimental and numerical investigation of the performance of a sorbent polymer composite (SPC) material used for removing mercury from the flue gases in a full-scale industrial installation. The investigated material is an attractive alternative to activated carbon, which is commonly used for this purpose. While the application of the SPC is characterized by high capital expenditures, this technology offers...
-
Modulation of carcinogen metabolizing cytochromes p450 in rat liver and kidney by cabbage and sauerkraut juices: comparison with the effects of indole-3-carbinol and phenethyl isothiocyanate
PublikacjaThis study investigated the effect of raw cabbage and sauerkraut juices on the activity and expression of CYP1A1, 1A2, 1B1 and 2B in Wistar rat liver and kidney. The results were compared with those of two commercially available products of glucosinolates degradation: indole-3-carbinol (I3C) and phenethyl isothiocyanate (PEITC). Significant differences in the effect of the cabbage juices as well as I3C and PEITC between the liver...
-
Reliability and Validity of Optoelectronic Method for Biophotonical Measurements
PublikacjaReliability and validity of measurements is of utmost importance when assessing measuring capability of instruments developed for research. In order to perform an experiment which is legitimate, used instruments must be both reliable and valid. Reliability estimates the degree of precision of measurement, the extent to which a measurement is internally consistent. Validity is the usefulness of an instrument to perform accurate...
-
SIMULATION OF PROCEED® SURGICAL MESH APPLIED TO VENTRAL HERNIA REPAIR
PublikacjaIn the present research, Proceed® implant is considered. The system is subjected to short-time dynamic pressure load, similar to post-operative cough naturally occurring in human abdomen. The model refers to a clinical case of 5cm of hernia operated by Proceed implant fixed by 15 joints every 3cm around the orifice. The simulations of the implanted mesh are performed by means of the Finite Element Method. The implant is modelled...
-
Research on operational characteristics of tyres with run flat insert
PublikacjaThe paper describes results of research on heavy vehicle tyre with Run Flat VFI insert. The experiment has included the determination of heat generation, rolling resistanceand radial stifnessof two different tyre designes (textile and steel carcass). The results have been used for the purpose of ewalution of tyre operating characteristics. The study included research on non-inflated tyre properties. The purpose of the paper is...
-
Tyre/road noise reduction of poroelastic road surface tested in a laboratory
PublikacjaA so-called poroelastic road surface (PERS) is being developed in Europe. This contains a large percentage of rubber particles mixed with hard aggregate (stone and sand) and bound with polyurethane. This gives high air void content (around 30 %), high elasticity and smooth texture, all of which should give low noise properties. Inthis experiment anominally 30 mm thick sample of PERS was mounted on a steel drum. Various car tyres...
-
Evaluation of the Impact of Storage Conditions on the Biogenic Amines Profile in Opened Wine Bottles
PublikacjaA survey of biogenic amine (BA) profiles in opened wine bottles has been established to monitor the level of biogenic amines (BAs) in opened bottles against time and other conditions. Bottles of red and white wine were submitted to different temperatures, stopper type (screw cap, cork), and use of vacuum devices. A total of six wines made from a variety of grapes were obtained from vineyards from regions across Poland. Dispersive...
-
Electron-impact dissociation of molecular hydrogen: benchmark cross sections
PublikacjaWe present a joint experimental and theoretical investigation of a fundamental process in atomic and molecular physics: electron impact excitation of molecular hydrogen’s (H2) most dominant transition (X1Σg+ → b3Σu+). Excitation of this state is by far the main channel that causes the dissociation of H2 into H + H atoms at low energies. The Convergent Close-Coupling (CCC) calculations predicted significant, more than factor of...
-
Novel method of estimation of inertial and dissipative parameters of a railway pantograph model
PublikacjaAn increase in electric railway vehicles service velocity requires that correct interaction between the pantograph and the catenary is ensured. This implies the need for developing mathematical models of pantographs and catenaries and determining their parameters. The article presents a method to determine parameters of mechanical joints of a railway pantograph based on analysis of pantograph subassemblies in swinging motion. The...
-
Simultaneous removal of heavy metals and dyes in water using a MgO-coated Fe3O4 nanocomposite: Role of micro-mixing effect induced by bubble generation
PublikacjaThis study focused on the development of a nano-adsorbent for contaminant removal without the use of any external energy. An eco-friendly Fe3O4@MgO core-shell nanocomposite was synthesized and tested for the removal of a heavy metal, lead (Pb2+) and a dye, rhodamine B (RhB). The addition of H2O2 into the system enabled the self-mixing of the aqueous solution containing Fe3O4@MgO through the generation of bubbles. This system showed...
-
THE PROBLEM OF AIRFLOW AROUND BUILDINGS CLUSTERS IN DIFFERENT CONFIGURATIONS
PublikacjaIn the paper, the authors discuss the construction of a model of an exemplary urban layout. Numerical simulation has been performed by means of a commercial software Fluent using two different turbulence models: the popular k-ε realizable one, and the Reynolds Stress Model (RSM), which is still being developed. The former is a 2-equations model, while the latter – is a RSM model – that consists of 7 equations. The studies have...
-
THE RESEARCH ON EGNOS SYSTEM IN CONTEXT OF THE ABILITY TO DETERMINE THE SHIP’S HULL SPATIAL ORIENTATION
PublikacjaThe European Geostationary Navigation Overlay Service (EGNOS) thanks to geostationary satellites covers an area of whole Europe, including Baltic and North Sea. It allows to fix the coordinates of object position with typical absolute accuracy of 1,5 m. Previous research have shown that relative accuracy is usually higher than absolute one [Nowak A., 2010, Nowak A., 2011], so probably it could be possible to use EGNOS to determine...
-
Remote sensing and photogrammetry techniques in diagnostics of concrete structures
PublikacjaRecently laser scanning technologies become widely used in many areas of the modern economy. In the following paper authors show a potential spectrum of use Terrestrial Laser Scanning (TLS) in diagnostics of reinforced concrete elements. Based on modes of failure analysis of reinforcement concrete beam authors describe downsides and advantages of adaptation of terrestrial laser scanning to this purpose, moreover reveal under which...
-
Estimation of Average Speed of Road Vehicles by Sound Intensity Analysis
PublikacjaConstant monitoring of road traffic is important part of modern smart city systems. The proposed method estimates average speed of road vehicles in the observation period, using a passive acoustic vector sensor. Speed estimation based on sound intensity analysis is a novel approach to the described problem. Sound intensity in two orthogonal axes is measured with a sensor placed alongside the road. Position of the apparent sound...
-
Time travel without paradoxes: Ring resonator as a universal paradigm for looped quantum evolutions
PublikacjaA ring resonator involves a scattering process where a part of the output is fed again into the input. The same formal structure is encountered in the problem of time travel in a neighborhood of a closed timelike curve (CTC). We know how to describe quantum optics of ring resonators, and the resulting description agrees with experiment. We can apply the same formal strategy to any looped quantum evolution, in particular to the...
-
Use of a Least Squares with Conditional Equations Method in Positioning a Tramway Track in the Gdansk Agglomeration
PublikacjaSatellite measurement techniques have been used for many years in different types of human activity, including work related to staking out and making use of rail infrastructure. First and foremost, satellite techniques are applied to determine the tramway track course and to analyse the changes of its position during its operation. This paper proposes using the least squares with conditional equations method, known in geodesy (LSce)....
-
High-temperature Corrosion of ~ 30 Pct Porous FeCr Stainless Steels in Air: Long-Term Evaluation Up to Breakaway
PublikacjaIn this work, a long-term (up to 6000 hours) corrosion evaluation of three porous (~ 30 pct of initial porosity) ferritic iron-chromium alloys with different Cr contents (20, 22, and 27 wt pct of Cr) was carried out at 600 C, 700 C, 800 C, and 900 C in air. Mass gain measurements and SEM analyses revealed that at temperatures above 600 C, all alloys exhibit breakaway corrosion, whereas at 600 C, none of the alloys were heavily...
-
Shaking table experimental study on damage mechanism of the disconnecting switch under seismic excitation
PublikacjaThe efficiency of the energetic network is a very import safety issue in the region experienced by the earthquake. High voltage disconnecting switches are important elements of the energetic infrastructure used to separate electric circuits (i.e. during repairs), which should not be damaged remaining fully operational. The aim of the paper is to show the results of the shaking table experimental investigation focused on damage...
-
Dimensional Synthesis of Coupled-Resonator Pseudoelliptic Microwave Bandpass Filters with Constant and Dispersive Couplings
PublikacjaIn this paper, we propose a novel technique for the dimensional synthesis of coupled-resonator pseudoelliptic microwave filters with constant and dispersive couplings. The proposed technique is based on numerical simulations of small structures, involving up to two adjacent resonators, and it accounts for a loading effect from other resonators by replacing them with terminations coupled through appropriately scaled inverters. The...
-
Temperature influence on tyre/road noise of selected tyres
PublikacjaAir and road temperatures substantially affect road vehicle noise emission. The temperature influence on tyre/road noise depends mainly on tyre-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tyres. The correction procedures for temperature effect are still under consideration and preparation. Tyre/road noise measurements using CPX method were performed...
-
Ontology-Aided Software Engineering
PublikacjaThis thesis is located between the fields of research on Artificial Intelligence (AI), Knowledge Representation and Reasoning (KRR), Computer-Aided Software Engineering (CASE) and Model Driven Engineering (MDE). The modern offspring of KRR - Description Logic (DL) [Baad03] is considered here as a formalization of the software engineering Methods & Tools. The bridge between the world of formal specification (governed by the mathematics)...
-
Cross sections for electron collision with pyridine [C5H5N] molecule
PublikacjaThe absolute grand -total cross section (TCS) for electron scattering from pyridine, C5H5N, molecules has been measured at impact energies from 0.6 to 300 eV in the linear electron-transmission experiment. The obtained TCS energy dependence appears to be typical for targets of high electric-dipole moment; the cross section generally decreases with rising energy, except for the 3–20 eV range, where a broad enhancement peaked near...
-
Heat exchange enhancement of jet impingement cooling with the novel humped-cone heat sink
PublikacjaJet impingement cooling technology is applicable to control temperature of devices, where very high heat flux is generated within a small area. This paper is about the improvement of the jet impingement cooling efficiency by the heat sink geometry modification. Two reference cases were sourced from the literature – flat heat sink and modified one with cone in the jet stagnation region. Such a change improves cooling capability...
-
In situ study of a composition of outlet gases from biogas fuelled Solid Oxide Fuel Cell performed by the Fourier Transform Infrared Spectroscopy
PublikacjaThe purpose of this study was to develop a method and software based on the Fourier Transform Infrared Spectroscopy for the in-situ, quantitative analysis of the composition of outlet gases from Solid Oxide Fuel Cell (SOFC). The calibration procedure performed at the beginning of the experiment indicated a polynomial dependence between the concentration of a calibrating gas (CO, CO2, CH4) and the corresponding integrated absorbance in...
-
ENHANCED EVAPORATION OF THE DROPLETS OF CONDENSATE IN THE ASYMMETRICAL SHOCK WAVE ZONE
PublikacjaIn the low-pressure part of steam turbine, the state path usually crosses the saturation line in penultimate stages [4,5]. The formation and evolution of these droplets lower the performance of the wet stages of the turbines, and their effects on the efficiency are collectively known as wetness losses [4]. Nowadays, due to work of steam turbines at partial load, process of homogeneous and heterogeneous condensation still is current....
-
Problems of modelling toxic compounds emitted by a marine internal combustion engine for the evaluation of its structure parameters
PublikacjaThe paper presents the possibility of using an analytical study of the engine exhaust ignition to evaluate the technical condition of the selected components. Software tools available for the analysis of experimental data commonly use multiple regression model that allows the study of the effects and iterations between model input quantities and one output variable. The use of multi-equation models gives a lot of freedom in the...
-
A novel in vivo approach to assess strains of the human abdominal wall under known intraabdominal pressure
PublikacjaThe study concerns mechanical behaviour of a living human abdominal wall. A better mechanical understanding of a human abdominal wall and recognition of its material properties is required to find mechanically compatible surgical meshes to significantly improve the treatment of ventral hernias. A non-invasive methodology, based on in vivo optical measurements is proposed to determine strains of abdominal wall corresponding to...
-
Evolution of Ag nanostructures created from thin films: UV–vis absorption and its theoretical predictions
PublikacjaAg-based plasmonic nanostructures were manufactured by thermal annealing of thin metallic films. Structure and morphology were studied using scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HR-TEM) and X-ray photoelectron spectroscopy (XPS). SEM images show that the formation of nanostructures is influenced by the initial layer thickness as well as the...
-
New light on the photocatalytic performance of NH4V4O10 and its composite with rGO
PublikacjaSolar-driven photocatalysis has shown great potential as a sustainable wastewater treatment technology that utilizes clean solar energy for pollutant degradation. Consequently, much attention is being paid to the development of new, efficient and low-cost photocatalyst materials. In this study, we report the photocatalytic activity of NH4V4O10 (NVO) and its composite with rGO (NVO/rGO). Samples were synthesized via a facile one-pot...
-
Modified linear viscoelastic model of earthquake-induced structural pounding
PublikacjaIn recent times, earthquake-induced structural pounding has been intensively studied through the use of different impact force models. The numerical results obtained from the previous studies indicate that the linear viscoelastic model is relatively simple and accurate in modeling pounding-involved behavior of structures during earthquakes. The only shortcoming of the model is a negative value of the pounding force occurring just...
-
Preliminary Testing of the Influence of Modified Polycaprolactones on Anabaena Variabilis Growth in Seawater
PublikacjaSeveral new biodegradable polymer materials have recently come onto the global market. Mostly the results on degradation kinetic studies are presented. This paper suggests using one of the tests to estimate the impact of polymer packaging material on sea life. The microorganism chosen was Anabaena variabilis (identified in many waters, including those of the Baltic Sea, especially in the Gulf of Gdansk and Puck Bay; this cyanobacterium...
-
The role of biodegradable particulate and colloidal organic compounds in biological nutrient removal activated sludge systems
PublikacjaThe efficiency of denitrification and enhanced biological phosphorus removal in biological nutrient removal activated sludge systems is strongly dependent on the availability of appropriate carbon sources. Due to high costs of commercial compounds (such as methanol, ethanol, acetic acid, etc.) and acclimation periods (usually) required, the effective use of internal substrates is preferred. The aim of this study was to determine...
-
Mechanical and structural investigations of wings of selected insect species
PublikacjaThis paper presents research and measurements leading to obtaining the Young’s modulus of wing bearing structures of selected insect species. A small testing machine intended for three-point bending and equipped with instruments registering low forces was constructed for the needs of the experiment. The machine was used to perform numerous bending tests of wings of three species of insects (obtained from a breeding farm): Attacus...
-
The Analysis of Working Parameters Decrease in Photovoltaic Modules as a Result of Dust Deposition
PublikacjaThe aspect of dust accumulation on the surface of photovoltaic (PV) modules should be thoroughly understood in order to minimize possible obstacles affecting energy generation. Several elements affect the amount of pollutant gathered on the surface of a solar device, mainly its localization, which is irreversibly linked to factors such as annual rainfall, occasional snow coverage, or, in a dry climate, increased blow of dust during...
-
Coupling between Blood Pressure and Subarachnoid Space Width Oscillations during Slow Breathing
PublikacjaThe precise mechanisms connecting the cardiovascular system and the cerebrospinal fluid (CSF) are not well understood in detail. This paper investigates the couplings between the cardiac and respiratory components, as extracted from blood pressure (BP) signals and oscillations of the subarachnoid space width (SAS), collected during slow ventilation and ventilation against inspiration resistance. The experiment was performed on...
-
Impact of soluble organic matter and particulate organic matter on anammox system: Performance, microbial community and N2O production
PublikacjaIn this study, the effects of soluble readily biodegradable COD (sCOD) and particulate slowly biodegradable COD (pCOD) on anammox process were investigated. The results of the longterm experiment indicated that a low sCOD/N ratio of 0.5 could accelerate the anammox and denitrification activity, to reach as high as 84.9% ±2.8% TN removal efficiency. Partial denitrification-anammox (PDN/anammox) and denitrification were proposed...
-
Detection of anomalies in bee colony using transitioning state and contrastive autoencoders
PublikacjaHoneybees plays vital role for the environmental sustainability and overall agricultural economy. Assisting bee colonies within their proper functioning brings the attention of researchers around the world. Electronics systems and machine learning algorithms are being developed for classifying specific undesirable bee behaviors in order to alert about upcoming substantial losses. However, classifiers could be impaired when used...
-
Categorization of emotions in dog behavior based on the deep neural network
PublikacjaThe aim of this article is to present a neural system based on stock architecture for recognizing emotional behavior in dogs. Our considerations are inspired by the original work of Franzoni et al. on recognizing dog emotions. An appropriate set of photographic data has been compiled taking into account five classes of emotional behavior in dogs of one breed, including joy, anger, licking, yawning, and sleeping. Focusing on a particular...
-
Condition-Based Monitoring of DC Motors Performed with Autoencoders
PublikacjaThis paper describes a condition-based monitoring system estimating DC motor degradation with the use of an autoencoder. Two methods of training the autoencoder are evaluated, namely backpropagation and extreme learning machines. The root mean square (RMS) error in the reconstruction of successive fragments of the measured DC motor angular-frequency signal, which is fed to the input of autoencoder, is used to determine the health...
-
Unique agreement of experimental and computational infrared spectroscopy: a case study of lithium bromide solvation in an important electrochemical solvent
PublikacjaInfrared (IR) spectroscopy is a widely used and invaluable tool in the studies of solvation phenomena in electrolyte solutions. Using state-of-the-art chemometric analysis of a spectral series measured in a concentration-dependent manner, the spectrum of the solute-affected solvent can be extracted, providing a detailed view of the structural and energetic states of the solvent molecules influenced by the solute. Concurrently,...
-
Cross-sections for electron-scattering from 2-methyl-1-buten-3-yne, C 5 H 6 , molecules
PublikacjatCross-sections for electron collisions with the 2-methyl-1-buten-3-yne [H2C C(CH3)C CH] moleculewere measured and calculated. Absolute grand-total electron-scattering cross-section (TCS) was takenat impact energies from 0.6 to 300 eV in the linear electron-transmission experiment. The TCS energydependence for the electron–C5H6collision has two prominent enhancements separated with a deepminimum located near 1.8 eV. In addition,...
-
Chromium (III) removal by perennial emerging macrophytes in floating treatment wetlands
PublikacjaFloating treatment wetlands (FTWs) are a sustainable solution to treat polluted water, but their role in chromium (Cr(III)) removal under neutral pH conditions remains poorly understood. This study evaluated the potential of FTWs planted with two perennial emergent macrophytes, Phragmites australis and Iris pseudacorus, to remove Cr(III) and nutrients (N and PO4-P) from water containing 7.5 mg/L TN, 1.8 mg/L PO4-P, and Cr(III)...
-
Joint experimental and theoretical study on electron scattering from titanium tetrachloride (TiCl4) molecule
PublikacjaAbsolute grand-total cross section for electron scattering from titanium tetrachloride, TiCl4, molecule was measured at electron-impact energies ranging from 0.3 to 300 eV, in the linear electron-transmission experiment. The elastic integral, differential, momentum transfer, and total ionization cross sections for TiCl4 molecule were also calculated for low and intermediate collisional energies at the level of various theories. The...
-
ENERGY ANALYSIS OF THE PROPULSION SHAFT FATIGUE PROCESS IN A ROTATING MECHANICAL SYSTEM PART II IDENTIFICATION STUDIES – DEVELOPING THE FATIGUE DURABILITY MODEL OF A DRIVE SHAFT
PublikacjaThe article presents a continuation of research carried out concerning identification of energy consequences of mechanical fatigue within a propeller shaft in a rotating mechanical system, while working under conditions of the loss of the required alignment of shaft lines. Experimental research was carried out on a physical model reflecting a full-sized real object: i.e., the propulsion system of the ship. It is proven, by means...