Filtry
wszystkich: 1237
wybranych: 1139
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: AMPHIBIOUS VEHICLE, WATER ENTRY, MODEL TESTS, CFD
-
Numerical Evaluation of Dynamic Response of a Steel Structure Model under Various Seismic Excitations
PublikacjaThe present paper reports the results of the study, which was designed to perform a numerical evaluation of dynamic response of a single-storey steel structure model. The experimental model was previously subjected to a number of different earthquake ground motions during an extensive shaking table investigation. The analyzed structure model was considered as a 1-DOF system with lumped parameters, which were determined by conducting...
-
Solvent Screening for Solubility Enhancement of Theophylline in Neat, Binary and Ternary NADES Solvents: New Measurements and Ensemble Machine Learning
PublikacjaTheophylline, a typical representative of active pharmaceutical ingredients, was selected to study the characteristics of experimental and theoretical solubility measured at 25 °C in a broad range of solvents, including neat, binary mixtures and ternary natural deep eutectics (NADES) prepared with choline chloride, polyols and water. There was a strong synergistic effect of organic solvents mixed with water, and among the experimentally...
-
Laboratory test rig for examining aggregate mining from seabed using the AIRLIFT method
PublikacjaThe use of the Airlift method for transporting the mined aggregate from the seabed to the deck of the mining ship is an alternative for presently used solutions, such as suction pumps or scoop transport for instance. Building the laboratory test rig was preceded by tests in natural conditions. The rig was designed in such a way as to model these conditions as close as possible, and to have potential for further development
-
Wet H2S corrosion and degradation of pipeline in amine regeneration system
PublikacjaThe paper presents the results of NDT examinations, metallographic tests and risk assessment of degradation related to corrosion of amine regeneration unit in a desulphurisation system. Intensive corrosion resulting from acid gases environment upon water condensation causes perforation of the pipeline. Detailed analysis reveals cracking related to the mechanism of wet H2S. Hydrogen penetration, resulting from the wet H2S process,...
-
Low cost real time UAV stereo photogrammetry modelling technique – accuracy considerations
PublikacjaThe paper presents accuracy considerations regarding three 3D modelling techniques. The tested new consumer type stereo camera (ZED 3D Stereolabs) has been implemented info an aerial mapping system, on board micro air vehicle MAV) and tested object has been mapped using a real-time photogrammetry with original real-time software application. The evaluated results has been compared with model gained with a state of art unmanned...
-
Study of Noise Propagation for Small Vessels
PublikacjaThe paper presents the results of the noise propagation analysis in ship structures tested in a number of AHTS (Anchor Handling Tug Supply) vessels. Statistical Energy Analysis (SEA) based on numerical model developed specially for the purpose of this numerical investigation were conducted. This numerical model enabled the analysis of both the structural elements and the acoustic spaces. For the detailed studies 47 points fixed...
-
Representation of magnetic hysteresis in tape wound core using feedback Preisach model
PublikacjaThis paper presents a mathematical model for the hysteresis phenomenon in ferromagnetic tape wound core. The feedback scalar Preisach model of hysteresis is used to simulate magnetic behavior of the grain oriented silicon strip of ET114-27 type. Determination of B-H hysteretic curve is based on measurement of the initial magnetization curve and the main hysteresis loop. The Preisach distribution function (PDF) of ET114-27 material...
-
Flow Process Models for Pipeline Diagnosis
PublikacjaThis chapter examines the problem of modeling and parameterization of the transmission pipeline flow process. First, the base model for discrete time is presented, which is a reference for other developed models. Then, the diagonal approximation (AMDA) method is proposed, in which the tridiagonal sub-matrices of the recombination matrix are approximated by their diagonal counterparts, which allows for a simple determination of...
-
Aqueous solutions of NMA, Na2HPO4 , and NaH2PO4 as models for interaction studies in phosphate–protein systems
PublikacjaPhosphate buffers are essential for many areas of studies. However, their influence on buffered systems is often ignored. The phosphate salts can interact with biologically important macromolecules (e.g. proteins) and stabilize or destabilize them. With our research, we want to answer question what kind of interactions, if any, occur between phosphate ions and a protein backbone model — N-methylacetamide (NMA). ATR-FTIR spectroscopy...
-
Sensitivity of the Baltic Sea level prediction to spatial model resolution
Publikacjahe three-dimensional hydrodynamic model of the Baltic Sea (M3D) and...
-
Monitoring of Chlorine Concentration in Drinking Water Distribution Systems Using an Interval Estimator
PublikacjaThis paper describes the design of an interval observer for the estimation of unmeasured quality state variables in drinking water distribution systems. The estimator utilizes a set bounded model of uncertainty to produce robust interval bounds on the estimated state variables of the water quality. The bounds are generated by solving two differential equations. Hence the numerical efficiency is sufficient for on-line monitoring...
-
Integrated information and prediction Web Service WaterPUCK General concept
PublikacjaIn this paper, general concept of a new method as ‘Integrated information and prediction Web Service WaterPUCK’ for investigation influence of agricultural holdings and land-use structures on coastal waters of the southern Baltic Sea is presented. WaterPUCK Service is focused on determination of the current and future environmental status of the surface water and groundwater located in the Puck District (Poland) and its impact...
-
Observation Value Analysis – Integral Part of Bayesian Diagnostics
PublikacjaThe decision making process, in general, is understood as a process of selecting one of the available solutions to the problem. One of possible approaches supporting the process is Bayesian statistical decision theory providing a mathematical model to make decisions of a technical nature in conditions of uncertainty. Regarding above, a detailed subject of the research is to analyze the value of the observation, which is a part...
-
GRAPHICAL REPRESENTATION OF MUSIC SET BASED ON MOOD OF MUSIC. GRAFICZNA PREZENTACJA ZBIORU MUZYCZNEGO OPARTA NA ANOTACJI NASTROJU MUZYKI
PublikacjaOne of the features for music recommendation, which is useful and intuitive for music listen-ers, is “mood”. The paper presents an approach to graphical representation of mood of music pieces. Subjective evaluation based on listening tests is performed for assigning mood labels of 150 pieces of music and placing them on the 2D mood plane. As a result, a map of songs is created, where music excerpts with similar mood are organized...
-
Experimental determination of dynamic properties of cylindrical steel tank model filled with liquid
PublikacjaIn technical branches, such as chemical or petroleum industries, cylindrical steel tanks are essential structures used for storage of liquid products. Any failure might have disastrous consequences, therefore their safety and reliability is essential. The aim of the present paper is to show the results of the experimental study which has been conducted on a scaled model of a real tank used in Poland. The investigation was carried...
-
Effect of adhesive compliance in the assessment of soft adhesives with the wedge test
PublikacjaWedge tests are usually analysed assuming that the free, unbonded members may be treated as encastré cantilever beams. However, if the adhesive layer is sufficiently flexible (e.g., due to low elastic modulus), then significant strain in the bonded region may occur and lead to modification of the behaviour outside this region. Using in conjunction a sensitive strain gauge method on asymmetric wedge tests and a mathematical analysis...
-
Influence of dissolved organic nitrogen on surface waters
PublikacjaThe aim of this study was to determine the susceptibility of dissolved organic nitrogen (DON) contained in biologically treated wastewater disposed from municipal wastewater treatment plants (WWTPs) to biodegradability and bioavailability in a water environment. Additionally an evaluation was performed of the participation of this organic nitrogen fraction, including bioavailable DON (bDON), in the nitrogen balance for the Baltic...
-
Classifying Emotions in Film Music - A Deep Learning Approach
PublikacjaThe paper presents an application for automatically classifying emotions in film music. A model of emotions is proposed, which is also associated with colors. The model created has nine emotional states, to which colors are assigned according to the color theory in film. Subjective tests are carried out to check the correctness of the assumptions behind the adopted emotion model. For that purpose, a statistical analysis of the...
-
Verification of baffle factor for straight pipe flow
PublikacjaDuring the water disinfection devices designing, it is often assumed that the baffle factor for a straight pipe reactors is equal to one. It would be possible only for the plug flow, which is a simplified model of the flow and does not appear in real situations. The paper contains an equation which enables calculation of the real value of the baffle factor for the pipe flow.
-
Optimizing CO2 Purification in a Negative CO2 Emission Power Plant
PublikacjaIn the pursuit of mitigating CO2 emissions, this study investigates the optimisation of CO2 purification within a Negative CO2 Emission Power Plant using a spray ejector condenser (SEC) coupled with a separator. The approach involves direct-contact condensation of vapour, primarily composed of an inert gas (CO2), facilitated by a subcooled liquid spray. A comprehensive analysis is presented, employing a numerical model to simulate...
-
A concept of heterogeneous numerical model of concrete for GPR simulations
PublikacjaThe Ground Penetrating Radar (GPR) method, which is increasingly being used in the non-destructive diagnostics of reinforced concrete structures, often needs more accurate interpretation tools for analysis of experimental data. Recently, there has been growing interest in developing of various numerical models for exhaustive understanding of GPR data. This paper presents the concept of a heterogeneous numerical model of concrete,...
-
Thin-walled frames and grids - statics and dynamics
PublikacjaFrames and grids assembled with thin-walled beams of open cross-section are widely applied in various civil engineering and vehicle or machine structures. Static and dynamic analysis of theses structures may be carried out by means of different models, startingfrom the classical models made of beam elements undergoing the Kirchhoff assumptions to the FE discretization of whole frame into plane elements. The former model is very...
-
Estimation and modeling hydrolysis of slowly biodegradable substrate based on the batch respirometric tests in activated sludge systems
PublikacjaNowadays, appropriate determination of chemical oxygen demand (COD) fractionation together with degradation kinetics of organic compounds have a prime importance on the design and operation of activated sludge systems. Batch respirometric tests based on the oxygen uptake rates (OUR) and corresponding COD is accepted method to reflect the consumption of biodegradable substrates. The influence of the readily biodegradable (Ss) fraction...
-
Przegląd i analiza układów napędowych stosowanych w rowerach elektrycznych
PublikacjaStreszczenie ang. : The purpose of his article is an overview and analysis of the drive system used in electrical bikes. Classical and modern drive system are described. The stress is putted on the electrical motors used in that applications. Structure, control and power supply of most recent design are presented. The analysis applies to hub motor type Clyte 408 used as a bike drive. Authors have decided to build a filed-circuit...
-
The analysis of soil resistance during screw displacement pile installation
PublikacjaThe analysis of soil resistances during screw displacement pile installation based on model and field tests. The investigations were carried out as a part of research project, financed by the Polish Ministry of Science and Higher Education. A proposal of empirical method for prediction of rotation resistance (torque) during screw auger penetration in non-cohesive subsoil based on CPT result.
-
Architectural and Urban Planning Solutions for the Protection of Heritage Buildings in the Context of Terrorist Attacks: Following the Example of Passive Protection Systems
PublikacjaEvents in recent years showing numerous terrorist attacks raise awareness regarding the neces-sity of considering the safety of heritage buildings. The analysis of available data allows us to conclude that it is not possible to fully prevent terrorist attacks. On the other hand, it is possible to minimize the impact of such incidents through proper design of Passive Protection System (PPS) components. One possible architectural...
-
Study on the Positioning Accuracy of GNSS/INS Systems Supported by DGPS and RTK Receivers for Hydrographic Surveys
PublikacjaHydrographic surveys, in accordance with the International Hydrographic Organization (IHO) S-44 standard, can be carried out in the following five orders: Exclusive, Special, 1a, 1b and 2, for which minimum accuracy requirements for the applied positioning system have been set out. They are as follows, respectively: 1, 2, 5, 5 and 20 m, with a confidence level of 95% in twodimensional space. The Global Navigation Satellite System...
-
Evaluating the influence of radiative heat flux on convective heat transfer from a vertical plate in air using an improved heating plate
PublikacjaThis article examines the influence of radiative heat flux on the accuracy of the results of free convective heat transfer in air. In order to carry out these tests, based on the experience gained during the operation of a plate heated on one side, compensated by a reverse heat loss flux counter-heater, a unique double-sided heating sandwich plate was designed and built, consisting of three thin epoxy resin plates reinforced with...
-
ANALYSIS OF ROLLING RESISTANCE OF TIRES WITH RUN FLAT INSERT APPLYING DRUM METHOD AND RADIAL CHARACTERISTIC
PublikacjaThis paper presents analysis of rolling resistance of tires with RUN FLAT insert applying drum method and radial characteristic. The conducted studies indicated changes in operational properties of wheel, occurring as a result of inflation pressure drop in the wheel. As regards radial elasticity, such changes result in significant drop of radial rigidity and increase of static deflection and increase of tire rolling resistance....
-
Analysis of AC/DC/DC Converter Modules for Direct Current Fast-Charging Applications
PublikacjaThe paper is a comprehensive laboratory comparison study of two galvanic isolated solution off-board battery chargers: (1) Si-based cost-effective case, and (2) SiC-bidirectional ready for vehicle to grid concept case. All circuits are modular, and in both cases the DC/DC converter can be replaced according to the end user requirements (the coupled transformer remains the same and is constructed based on 12xC100 cores to avoid...
-
Satellite pump and motor
PublikacjaThe article describe the design and operation of a prototype of satellite pump and a prototype of satellite motor. In both machines, the operating mechanism consists of a non-circular gear with external teeth (rotor), non-circular gear with internal teeth (curvature), and ten gear wheels which cooperate with the rotor and the curvature. The differences between the commutation unit in the pump and the commutation unit in the motor...
-
Mutual Clutter Suppression Techniques for FM Sonars
PublikacjaThe article presents methods that help in the elimination of mutual clutter as well as the consequences of two FM sounding signal sonars operating in the same body of water and frequency band. An in-depth analysis of mutual clutter was carried out. The effects of sounding signal differentiation were determined, as was the Doppler effect on mutual clutter suppression. One of the methods analysed is of particular interest in a situation...
-
Comparison of single microjet cooling with water, ethanol and HFE7100 as test fluids
PublikacjaThe paper presents the investigation of a single microjet cooling forming an thin liquid film on the impingement surface of specially designed rig. The basis of microjet technology is to produce laminar jets, which when impinging the surface have a very high kinetic energy at the stagnation point. Applied technology of jet production can result with the size of jets ranging from 20 to 500μm in breadth and 20 to 100μm in width....
-
Modelling of Diffusing Capacity Measurement Results in Lung Microangiopathy Patients. A novel Diagnostic Suppport
PublikacjaLung microangiopathy is a little known negative influence of diabetes mellitus on the functioning of the lungs. The aim of this study is to design a supportive method for diagnosing lung microangiopathy. This will be based on routinely performed pulmonary measurements as well as on investigation process modelling and data processing. A model of the diffusion of oxygen from the alveoli to the blood has been described with a set...
-
Analiza drgań przewodów jezdnych sieci trakcyjnej w aspekcie oceny jej stanu technicznego
PublikacjaW pracy przedstawiono możliwości wykorzystania analizy drgań przewodów jezdnych sieci trakcyjnej do oceny jej stanu technicznego. Zaprezentowano wyniki badań laboratoryjnych, w których rejestrowano drgania odcinka przewodu jezdnego o zróżnicowanym stopniu zużycia i przy różnych warunkach jego zawieszenia. Na bazie przeprowadzonych analiz w dziedzinie czasu i częstotliwości, wskazano zależności między stanem sieci a wybranymi parametrami...
-
Life tests of a rotary single-stage magnetic-fluid seal for shipbuilding applications
PublikacjaUse of the magnetic fluid seal technology in water is much more difficult technological problem in comparisonto gas or vacuum environment. Some seals constructed up to time been are designed as hybrid, two stagesealing structures with shields or mechanical seals used as protection measures to the magnetic fluid seal.Anyway, there is always problem with immediate contact between magnetic fluid and the environmentalliquid. In the...
-
Multi-stage magnetic-fluid seals for operating in water - life test procedure, test stand and research results
PublikacjaThe edge criteria for magnetic-fluid seals durability research are critical for the seal'stechnological usefulness. The magnetic fluid seal technology in water is much moredifficult technological problem in comparison to gas or vacuum environment. There isalways problem with immediate contact between magnetic fluid and the environmentaluninspected liquids. In the paper are presented ways of experiments definitions carried outwith...
-
Constrained aerodynamic shape optimization using neural networks and sequential sampling
PublikacjaAerodynamic shape optimization (ASO) involves computational fluid dynamics (CFD)-based search for an optimal aerodynamic shape such as airfoils and wings. Gradient-based optimization (GBO) with adjoints can be used efficiently to solve ASO problems with many design variables, but problems with many constraints can still be challenging. The recently created efficient global optimization algorithm with neural network (NN)-based prediction...
-
Effect of Pin Shape on Thermal History of Aluminum-Steel Friction Stir Welded Joint: Computational Fluid Dynamic Modeling and Validation
PublikacjaThis article studied the effects of pin angle on heat generation and temperature distribution during friction stir welding (FSW) of AA1100 aluminum alloy and St-14 low carbon steel. A validated computational fluid dynamics (CFD) model was implemented to simulate the FSW process. Scanning electron microscopy (SEM) was employed in order to investigate internal materials’ flow. Simulation results revealed that the mechanical work...
-
A material model of asphalt mixtures based on Monte Carlo simulations
PublikacjaThe paper aims to numerically reflect mineral-asphalt mixture structure by a standard FEM software. Laboratory test results are presented due to bending tests of circular notched elements. The result scatter is relatively high. An attempt was made to form a random aggregate distribution in order to obtain various results corresponding to laboratory tests. The material structure calibration, its homogenization and finite element...
-
A device for measuring heat flux on a rocket skin surface
PublikacjaA novel method for measuring heat flux on a surface is presented. It is an extensive upgrade of currently known heat flux sensors used mostly in civil engineering. As the thermal environment of launchers, especially sounding rocket can have an enormous negative effect on payload, careful considerations have to be taken in the process of preparing insulation. Usually, thermal data provided by the launch vehicle manufacturer is limited...
-
Enhanced cellulose extraction from agave plant (Agave americana Species) for synthesis of magnetic/cellulose nanocomposite for defluoridation of water
PublikacjaResearch on fluoride removal from water is currently focusing on the development of innovative materials for defluoridation water. The current study extracted and used enhanced cellulose from Agave americana species to synthesize a magnetic/cellulose nanocomposite for water defluoridation. Strong and light binary acids (H2SO4 and CH3COOH) were utilized to pretreat raw material to enhance cellulose extraction. Central composite...
-
Investigation of MIEX® resin sedimentation in the aspect of particle sizes remaining in the supernatant
PublikacjaThe aim of the study was to evaluate the effectiveness of the MIEX® resin sedimentation process, both new and repeatedly used in hybrid water treatment MIEX®DOC + microfiltration (MF) or ultrafiltration (UF) processes (repeatedly regenerated). The tests consisted of performing 1 h sedimentation of the suspension resin in nonflow conditions and analysis of supernatant water at different process durations. The suspension weight analysis...
-
Interactions between hydration spheres of two different solutes in solution: The least squares fitting with constraints as a tool to determine water properties in ternary systems
PublikacjaBiological systems are complex and the problem of their description lies in mutual interactions between their components. This paper is focused on model experiment-based studies which can reduce these difficulties. The ternary aqueous N-methylacetamide (NMA)–Na2HPO4 system has been studied by means of the FTIR spectroscopy. A novel difference spectra method aimed to extract the spectral contribution of water affected simultaneously...
-
Opracowanie technologii spawania naprawczego szyn poddźwigowych A120 oraz badania nieniszczące jakości szyn w DCT w Porcie Północnym
PublikacjaEkspertyza dotyczy realizacji zlecenia związanego z naprawą spoin szyn poddźwigowych na terenie terminalu kontenerowego - Deep Water Terminal (DCT) w Porcie Północnym w Gdańsku. W ramach opracowania: 1. Wykonano badania ultradźwiękowe (UT) i magnetyczno-proszkowe (MT) spoin czołowych szyn poddźwigowych typu A120, według schematu dostarczonego przez firmę SKANSKA S.A. 2. Wykonano analizę wyników badań...
-
Ocena zasobów oraz weryfikacja granic obszaru ochronnego GZWP nr 133 Młotkowo za pomocą numerycznego modelu przepływu wód podziemnych
PublikacjaModel Głównego Zbiornika Wód Podziemnych powstał w celu dokonania oceny dostępnych zasobów wód oraz zweryfikowania granic strefy ochronnej. GZWP Młotkowo jest położony w południowej części Pojezierza Krajeńskiego. Ze względu na konieczność weryfikacji granic zbiornika wyznaczonych przez Kleczkowskiego i in. (1990) do badań modelowych przyjęto obszar cztery razy większy niż rozmiar GZWP. W celu osiągnięcia najbardziej wiarygodnych...
-
Experimental and numerical study of thermal and electrical potential of BIPV/T collector in the form of air-cooled photovoltaic roof tile
PublikacjaAmong renewable energy sources, Building-Integrated Photovoltaic/Thermal (BIPV/T) systems are gaining increasing interest. To improve their economic competitiveness, technologies that increase their efficiency are searched for. The paper is devoted to evaluating the impact of various air-cooling configurations on the thermal and electrical performance of a photovoltaic roof tile. A numerical model of the own experimental system...
-
Comparison of traditional district heating with low temperature district heating systems featuring organic Rankine cycle and heat pump
PublikacjaPaper presents a comparison between a traditional district heating system with conventional boilers as a source of heat and electricity purchases from power utilities and a low temperature DH system incorporating the CHP with organic Rankine Cycle providing electricity and local heat pump raising the temperature of the DH fluid to the required temperature in the dwelling, meaning that both heat and electricity are produced within...
-
Physicochemical Properties and Application of Silica-Doped Biochar Composites as Efficient Sorbents of Copper from Tap Water
PublikacjaThis article concerns research on new sorption materials based on silica-doped activated carbon. A two-stage synthesis involved pyrolysis of plant material impregnated in a water glass solution , followed by hydrothermal activation of the pyrolysate in KOH solution. The resulting composite can be used as a sorbent in drinking water filters. The proposed method of synthesis enables the design of materials with a surface area...
-
Amides as models to study the hydration of proteins and peptides — spectroscopic and theoretical approach on hydration in various temperatures
PublikacjaInteractions with water are one of the key factors which determine protein stability and activity in aqueous solutions. However, the protein hydration is still insufficiently understood. N-methylacetamide (NMA) is regarded as a minimal part of the peptide backbone and the relative simplicity of its structure makes it a good model for studies on protein–water interactions. In this paper, the influence of NMA and N,N-dimethylacetamide...