Wyszukiwarka
Filtry
wszystkich: 1449
wybranych: 919
Wyniki wyszukiwania dla: MEASURING OF AXLE LOADS
-
An isogeometric finite element formulation for geometrically exact Timoshenko beams with extensible directors
PublikacjaAn isogeometric finite element formulation for geometrically and materially nonlinear Timoshenko beams is presented, which incorporates in-plane deformation of the cross-section described by two extensible director vectors. Since those directors belong to the space R3, a configuration can be additively updated. The developed formulation allows direct application of nonlinear three-dimensional constitutive equations without zero...
-
CFFT columns in road through railroad crossings
PublikacjaThere were 12801 road through railroad one-level crossings in Poland in 2018. 215 accidents happened at them in 2018. In order to increase safety in rail and road traffic two-level crossings should be used. They are definitely safer and make the traffic more smooth. In the design and construction of two-level intersections of railway and road or path columns of circular cross-section are often used. They can be successfully replaced...
-
MODELLING OF TOXIC COMPOUNDS EMISSION IN MARINE DIESEL ENGINE DURING TRANSIENT STATES AT VARIABLE PRESSURE OF FUEL INJECTION
PublikacjaTransient states are an important part of the spectrum of engine loads, especially the traction engines. In the case of marine diesel engines, transient states are of particular importance in reducing the analysis of motion units for special areas and maneuvering in port, the participation of transient states in the load spectrum significantly increases, also, the emission of toxic compounds from this period increases proportionally....
-
Wyznaczenie obciążeń na poszycie okrętu wywołanych uderzeniem fal i uderzeniem w lód i ich wpływ na bezpieczeństwo okrętu
PublikacjaThe main problem is the vessels rather accurate determination of the hydrodynamic loads so-called hydroelasticity outside . This can be done by theoretical analysis , computer simulation or by experiment. This gives the hydrodynamic pressure distribution on the walls of the ship's hull and also on the walls of marine vessels .The most dangerous are the impact of extreme storm waves , the impact of the wharf and the impact zone...
-
Implementation of Haar wavelet, higher order Haar wavelet, and differential quadrature methods on buckling response of strain gradient nonlocal beam embedded in an elastic medium
PublikacjaThe present investigation is focused on the buckling behavior of strain gradient nonlocal beam embedded in Winkler elastic foundation. The first-order strain gradient model has been combined with the Euler–Bernoulli beam theory to formulate the proposed model using Hamilton’s principle. Three numerically efficient methods, namely Haar wavelet method (HWM), higher order Haar wavelet method (HOHWM), and differential quadrature method...
-
Application of linear buckling sensitivity analysis to economic design of cylindrical steel silos composed of corrugated sheets and columns
PublikacjaThe paper deals with global stability of steel cylindrical silos composed of corrugated walls and vertical columns with loads imposed by a bulk solid following Eurocode 1. The optimum silo design with respect to the steel weight was based on a sensitivity analysis method. The changes of silo column profiles at each design step were performed by means of influence lines for the buckling load factor due to the unit column bending...
-
Evaluation of applicability of classic methods of a fault loop impedance measurement to circuits with residual current devices
PublikacjaMeasurement of fault loop impedance in low voltage grids and systems is in most cases performed to verify the effectiveness of protection against electric shock by automatic disconnection of supply. For the sake of measurement accuracy, it is advisable to perform it using large current. Unfortunately, in circuits with residual current devices which are very widely used nowadays, a large measurement current may trigger those devices...
-
Three-dimensional mapping for data collected using variable stereo baseline
PublikacjaThe paper describes a system of 3D mapping of data collected with due regard for variable baseline. This solution constitute an extension to a VisRobot sub-system developed as a subsystem, necessary for implementing the generic idea of using mobile robots to explore an indoor static environment. This subsystem is to acquire stereo images, calculate the depth in the images and construct the sought 3D map. Stereo images are obtained...
-
Generic appearance of objective results in quantum measurements
PublikacjaMeasurement is of central interest in quantum mechanics as it provides the link between the quantum world and the world of everyday experience. One of the features of everyday experience is its robust, objective character, contrasting the delicate nature of quantum systems. Here we analyze in a completely model-independent way the celebrated von Neumann measurement process, using recent techniques of information flow, studied in...
-
Triangular 3D Laser Scanning in Underwater Photogrammetry
PublikacjaThe use of triangular 3D laser scanning may significantly enhance the visual inspection of underwater objects. In these days of high demand for accurate information, exclusively photographic documentation is not enough, as it is geometrically flawed. The authors of this article are trying to present the rudiments of laser scanning, a modern means of measuring, which is reliable, relatively easy to use and works in accordance with...
-
Permeation and sorption properties of poly(ether-block-amide) membranesfilled by two types of zeolites
PublikacjaThe experimental study of transport properties of mixed matrix membranes (MMMs) based on PEBA-4033 with two types of zeolites is reported. Gas (CO2, O2, N2) and vapor (benzene, toluene, methanol, water) permeation measurements were performed using the differential flow permeameter at temperature of 298.15 K and at atmospheric pressure. Gas/vapor permeation was monitored by measuring the changes of the thermal conductivity of carrier...
-
Fast bubble dynamics and sizing
PublikacjaSingle bubble sizing is usually performed by measuring the resonant bubble response using the Dual Frequency Ultrasound Method. However, in practice, the use of millisecond-duration chirp-like waves yields nonlinear distortions of the bubble oscillations. In comparison with the resonant curve obtained under harmonic excitation, it was observed that the bubble dynamic response shifted by up to 20 percent of the resonant frequency...
-
The Smith-Watson-Topper parameter and fracture surface topography relationship for additively manufactured 18Ni300 steel subjected to uniaxial variable-amplitude loading
PublikacjaIn this paper, the association between Smith-Watson-Topper (SWT) parameter and fracture surface topography is studied in additively manufactured maraging steel exposed to variable-amplitude fatigue loading. The post-failure fracture surfaces were examined using a non-contact 3D surface topography measuring system and the entire fracture surface method. The focal point is on the correspondence between fatigue characteristics, articulate...
-
Temperature Measurements at Tyre Tread Rubber on Sandpaper Oscillatory Sliding Contacts Using Acicular Grindable Thermocouples
PublikacjaThe tribological performance of tyre–road contacts depends crucially on the contact temperature. This study investigates the reliability and accuracy of acicular grindable thermocouples possessing an original needle-shaped wearable part as applied to measuring temperature at the oscillatory sliding contact between a rubber tyre tread sample and a sandpaper. A linear oscillatory tribometer is used to imitate the sliding phase of...
-
Effect of waviness and roughness components on transverse profiles of turned surfaces
PublikacjaThis paper presents the authors method of simultaneous analysis of roughness and waviness irregularity components, with the aim of better defining the key qualities and characteristics.Periodical surface machining traces may be analyzed spectrally, with the irregularity's peaks and troughs being used to define the wave's amplitude.In this work the standard composition for filtering waviness and roughness components of a surface...
-
Determination of safety indicators of the freight wagons by mobile systems
PublikacjaThe organization of the movement of freight trains in Ukraine is an important factor in integrating the country’s railway transport into the European system. A situation that requires a significant renewal of the freight wagon park with modern wagons to meet the freight transportation requirements has arisen. Also, a significant drawback of railway transport in Ukraine is the limitation of the speed of trains, which include freight...
-
Enhancing Facial Palsy Treatment through Artificial Intelligence: From Diagnosis to Recovery Monitoring
PublikacjaThe objective of this study is to develop and assess a mobile application that leverages artificial intelligence (AI) to support the rehabilitation of individuals with facial nerve paralysis. The application features two primary functionalities: assessing the paralysis severity and facilitating the monitoring of rehabilitation exercises. The AI algorithm employed for this purpose was Google's ML Kit “face-detection”. The classification...
-
Tensile failure study of 3D printed PLA using DIC technique and FEM analysis
PublikacjaThe paper presents the experimental and numerical study of the failure behaviour of Fused Filament Fabricated (FFF) Polylactic Acid (PLA) samples subjected to tensile load. The examined samples are printed in flat orientation with 0◦, 45◦ and 90◦ raster angles. During the experiments the deformation of the specimens is continuously scanned with the 3D Aramis measuring system utilizing the digital imaging correlation technique,...
-
A New Approach to Capacitive Sensor Measurements Based on a Microcontroller and a Three-Gate Stable RC Oscillator
PublikacjaA complete smart capacitive sensor solution basedA complete smart capacitive sensor solution based on a microcontroller was developed. This approach includes the development of both the hardware and software. The hardware part comprises an 8-bit microcontroller equipped with two timers/counters and a three-gate stable RC relaxation oscillator. The software part handles system configuration, measurement control, communication control,...
-
Acoustic evaluation of road surfaces using different Close Proximity testing devices
PublikacjaAccording to the valid standard, Close Proximity (CPX) method intends to evaluate the influence of road surfaces on traffic noise. Measurements may be carried out with the use of a self-powered vehicle or a special test trailer equipped with testing tyre towed by another vehicle. Two different testing devices took part in the research organized in Poland in order to determine the ranking of road surfaces in terms of acoustic parameters....
-
Compensation of Voltage Drops in Trolleybus Supply System Using Battery-Based Buffer Station
PublikacjaThis paper analyzes the results of a trial operation of a battery-based buffer station supporting a selected section of trolleybus power supply systems in Pilsen, Czech Republic. The buffer station aims to prevent the catenary from excessive voltage drops in a part of the route that is most remote from the traction substation. Compensation of voltage drops is carried out by continuously measuring the catenary voltage and injecting...
-
Counting and tracking vehicles using acoustic vector sensors
PublikacjaA method is presented for counting vehicles and for determining their movement direction by means of acoustic vector sensor application. The assumptions of the method employing spatial distribution of sound intensity determined with the help of an integrated 3D intensity probe are discussed. The intensity probe developed by the authors was used for the experiments. The mode of operation of the algorithm is presented in conjunction...
-
Analyzing content of tasks in Business Process Management. Blending task execution and organization perspectives
PublikacjaAn efficient organization, management, and execution of tasks are central for the successful functioning of any organization. This topic was on the research agenda already in the early 1950s and keeps attracting the scientific community's attention today. Continuous advances and penetration of technologies in organizations are expected to increase task variety and complexity. This creates a constant demand for new methods to analyze,...
-
Molecular mobility of water protons under interaction with chemically modified starches. DSC and HMR-relaxation investigations
PublikacjaThe change of water protons mobility in the system chemically modified starches – water were investigated by DSC and NMR-relaxation methods. The amount of unfrozen water at subzero temperature as well as additional unfrozen water which appears after gelatinization have lower values for chemically modified starches in comparison with the native starch. The proton spin-spin relaxation time Т2 for chemically modified starch samples,...
-
Sounding rocket vibration mechanical filter and amplifier
PublikacjaMeasuring accelerations and vibrations of a sounding rocket provides both information for engineers on the launcher vehicle performance as well as environment description for future payload designers. Typically, information on the level of vibration and eigenfrequencies are required to properly design a payload. This paper presents a design of a novel mechanical filter and amplifier for mechanical vibrations. Its key feature is...
-
Identification of residual force in static load tests on instrumented screw displacement piles
PublikacjaOccurrence of the so-called residual force of an unknown value significantly disturbs interpretation of static load tests performed on piles equipped with additional measuring instruments. Screw displacement piles are the piling technology in which the residual force phenomenon is very common. Its formation mechanism is closely related to the installation method of this type of piles, which initiates generation of negative pile...
-
TEMPERATURE INFLUENCE ON TIRE ROLLING RESISTANCE MEASUREMENTS QUALITY
PublikacjaGlobal warming makes it necessary to reduce energy consumption, which in the case of motor vehicles, is connected, among other things, with reduction of resistive forces acting on a vehicle during its motion. One of the most important components of those forces is rolling resistance, which is very difficult to measure, especially in road conditions. The article deals with issues related to the influence of the thermal state of...
-
Impact of Shifting Time-Window Post-Processing on the Quality of Face Detection Algorithms
PublikacjaWe consider binary classification algorithms, which operate on single frames from video sequences. Such a class of algorithms is named OFA (One Frame Analyzed). Two such algorithms for facial detection are compared in terms of their susceptibility to the FSA (Frame Sequence Analysis) method. It introduces a shifting time-window improvement, which includes the temporal context of frames in a post-processing step that improves the...
-
Proceedings of the 9th International Conference on Structural Dynamics, EURODYN 2014
PublikacjaSince offshore wind turbine supporting structures are subjected to dynamic environments with time-varying loading conditions, it is important to model their dynamic behavior and validate these models by means of vibrational experiments. In this paper assessment of dynamical state of the structure is investigated by means of both: numerical modeling, and experimental modal analysis. In experimental modal analysis, capturing the...
-
Direction-of-Arrival Estimation Using an ESPAR Antenna with Simplified Beam Steering
PublikacjaIn this paper, it has been shown, how electronically steerable parasitic array radiator (ESPAR) antenna, in which beam steering is done in a simple way, can be used for directionof- arrival (DoA) estimation of an unknown signal impinging the antenna. The concept is based on an ESPAR antenna having twelve parasitic elements, in which beam switching is realized by RF switches providing required loads to its parasitic elements. Numerical...
-
Current harmonic controller in multiple reference frames for series active power filter integrated with 18-pulse diode rectifier
PublikacjaThe paper presents the control system and selected results of experimental tests of the AC/DC power converter consisting of an 18-pulse diode rectifier based on coupled reactors and a serial active power filter. Proportional integral controllers with decoupling components are implemented in multiple reference frames for selective line current harmonic suppression. The regulator is provided with a backtracking anti-windup mechanism...
-
Numerical Modelling of Connections Between Stones in Foundations of Historical Buildings
PublikacjaThe aim of this paper is to analyse the behaviour of old building foundations composed of stones (the main load-bearing elements) and mortar, based on numerical analysis. Some basic aspects of historical foundations are briefly discussed, with an emphasis on their development, techniques, and material. The behaviour of a foundation subjected to the loads transmitted from the upper parts of the structure is described...
-
Centrally Pivoted Tilting Pad Thrust Bearing with Carbon-Based Coated Collar—Experimental Results of Low- and Medium-Speed Operation
PublikacjaExperimental results of the research on a tilting pad thrust bearing with symmetrical pad support in the conditions of high loads and low speeds are presented in the paper. As described in the literature review, experimental results of tilting pad bearings at low speed/high load regime and transient conditions are rare. Unusual material selection - steel pad against a DLC-type coating on the collar was utilized. Such material combination...
-
Low Current Transformer Utilizing Co-Based Amorphous Alloys
PublikacjaMetal oxide surge arresters have been widely used for protection of power system networks against overvoltages due to atmospheric discharges or malfunction of devices connected to the network. During its operation a surge arrester structure is degradated, what can be observed as an increase of a surge arrester leakage current. Paper presents an implementation of a new, high-permeability, Co64Fe4Ni1Si15B14 amorphous alloy as a current...
-
Low current transformer utilizing Co-based amorphous alloys
PublikacjaMetal oxide surge arresters have been widely used for protection of power system networks against overvoltages due to atmospheric discharges or malfunction of devices connected to the network. During its operation a surge arrester structure is degradated, what can be observed as an increase of a surge arrester leakage current. Paper presents an implementation of a new, high-permeability, Co64Fe4Ni1Si15B14 amorphous alloy as a current...
-
Optimization of Division and Reconfiguration Locations of the Medium-Voltage Power Grid Based on Forecasting the Level of Load and Generation from Renewable Energy Sources
PublikacjaThe article addresses challenges in optimizing the operation of medium voltage networks, emphasizing optimizing network division points and selecting the best network configuration for minimizing power and energy losses. It critically reviews recent research on the issue of network configuration optimization. The optimization of the medium voltage power grid reconfiguration process was carried out using known optimization tools....
-
Experimental test results of an automatic voltage regulator with independent phase voltage controllers
PublikacjaThe growing number of distributed renewable energy sources and dynamic constant-power loads (e.g. electric vehicle charging stations) pose new challenges for network operators. These changes result in alterations to network load profiles and load flows, leading to greater voltage volatility. One effective solution to these problems can be the use of automatic voltage regulators (AVRs), which stabilize and symmetrize voltage output,...
-
Partially Isolated Multi-Active Bridge DC-DC Converter with Bidirectional EV Charging Ports
PublikacjaThere is a growing interest in multiport converters due to their ability to interconnect various energy sources and loads using reduced number of components. Regarding electric vehicle (EV) chargers connection, existing multiport solutions either lack scalability, featuring only one isolated charging port or the operation of ports depend on each other, complicating the converter control algorithm. This article proposes a partially...
-
Verification of punching shear outside the shear cap by the direct method
PublikacjaThe proposition of a method to verify the punching resistance for very large supports based on the EN 1992-1-1 standard is described in this paper. The present standard guidelines for the calculation of the punching resistance for large supports are also summarised. The proposed direct method is compared with other standard methods using an example taken from design practice. This method consists of a direct check of the shear...
-
Integrated Three-Level Dual-Phase Inverter
PublikacjaIn view of reducing the number of inverter legs that provide dual-phase, three-level output voltages (as may be needed in an uninterruptible power supply), and that also provide a wide range of output frequencies (as needed in an advanced motor drive system with wide speed ranges), a three-level, dual-phase inverter topology is presented in this paper. Its three-level attribute was based on the F-type inverter topological concept,...
-
Microstructure and Properties of Electroless Ni-P/Si3N4 Nanocomposite Coatings Deposited on the AW-7075 Aluminum Alloy
PublikacjaThe article presents the results of mechanical and tribological tests of Ni-P/Si3N4 nanocomposite coatings deposited on the AW-7075 aluminum alloy using the chemical reduction method. The influence of the chemical composition on the Vickers microhardness determined by the DSI method was examined. The nanocomposite layers were made of Si3N4 silicon nitride in a polydisperse powder with a particle size ranging from 20 to 25 nm. The...
-
CHARACTERIZATION STUDY ON MECHANICAL PROPERTIES OF POLYESTER COATED FABRIC
PublikacjaThe scope of the paper is to determine the mechanical properties of the Precontraint 1302 polyester coated fabric under uniaxial and biaxial tensile tests. The results are compared for Precontraint 1302 fabric and other types of coated fabrics. The author applied an orthotropic model and a dense net model to reflect the polyester coated fabric performance under uniaxial and biaxial tensile tests. Material parameters are specified...
-
Shape and force control of cable structures with minimal actuators and actuation
PublikacjaShape adjustment and stress control can be considered as one of the effective parameters in prestressed cable structures since such structures are widely constructed nowadays due to their characteristics. The assembly errors and applied loads hugely affect the cables’ nodal positions and stress due to their delicacy. The former could disturb the shape, which affects the appearance and the function of the structure. In contrast,...
-
30 years of treatment wetland application in poland- progress and reserch
PublikacjaThe experiences with design and operation of constructed wetlands in the Pommerania region during last 30 years followed by carried out investigations of treatment processes lead to the following conclusions:First applications of constructed wetlands for biological sewage treatment were made in 1984-92. The later implementations of multi-stage constructed wetlands in the individual household and local scale enable wastewater treatment...
-
Tribological Properties of Ni-P/Si3N4 Nanocomposite Layers Deposited by Chemical Reduction Method on Aluminum Alloy AW-7075
PublikacjaThe article presents the results of tribological tests of Ni-P/Si3N4 nanocomposite and Ni-P nickel layers deposited on the AW-7075 aluminum alloy by chemical reduction method, and the AW-7075 alloy without coating. Nanocomposite layers were produced using Si3N4 siliconnitride in the form of a polydisperse powder whose particle sizes ranged from 20 to 25 nm. The influence of the content of the dispersion phase layer material on...
-
Heavy duty vehicle fuel consumption modelling using artificial neural networks
PublikacjaIn this paper an artificial neural network (ANN) approach to modelling fuel consumption of heavy duty vehicles is presented. The proposed method uses easy accessible data collected via CAN bus of the truck. As a benchmark a conventional method, which is based on polynomial regression model, is used. The fuel consumption is measured in two different tests, performed by using a unique test bench to apply the load to the engine. Firstly,...
-
A constitutive law for concrete with smooth transition from continuous into discontinuous cracks’ description
PublikacjaPaper presents a constitutive model for concrete that combines a continuous and discontinuous crack’s description to simulate the concrete under tensile dominated loads. In a continuum regime, two different constitutive laws were used. First, a plasticity model with the Rankine failure criterion and an associated flow rule was used. Second, a constitutive law based on isotropic damage mechanics was formulated. Both model alternatives...
-
Influence of water and mineral oil on the leaks in satellite motor commutation unit clearances
PublikacjaThe article describes the flow rates of mineral oil and water flowing, as working media, through the commutation unit of a hydraulic satellite motor. It is demonstrated that geometrical dimensions of commutation unit clearances change as a function of the machine shaft rotation angle. Methods for measuring the rate of this flow and the pressure in the working chamber are presented. The results of pressure measurements in the working...
-
Problems and challenges associated with estimating the emissions of organic compounds from indoor materials
PublikacjaFor several years intensive research has been carried out with the aim of developing a database of the types and amounts of pollutants released from indoor materials to the indoor environment. The paper discusses in detail basic problems and challenges encountered when estimating the emissions of chemical compounds released from of indoor materials. Factors affecting the validity of data obtained by using two different types of...
-
Disaster-resilient communication networks: Principles and best practices
PublikacjaCommunication network failures that are caused by disasters, such as hurricanes, arthquakes and cyber-attacks, can have significant economic and societal impact. To address this problem, the research community has been investigating approaches to network resilience for several years. However, aside from well-established techniques, many of these solutions have not found their way into operational...