Filtry
wszystkich: 1403
wybranych: 1077
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: RESISTANCE
-
Initial Field Validation of Poroelastic Pavement Made with Crumb Rubber, Mineral Aggregate and Highly Polymer-Modified Bitumen
PublikacjaTire/road noise in most driving conditions dominates other sources of traffic noise. One of the most efficient ways of reducing tire/road noise is to use the so-called “low noise pavement”. According to numerous studies, at present, poroelastic road pavement that is composed of rubber and mineral aggregate and polyurethane or bituminous binder gives the best noise reduction up to 12 dB. Unfortunately, there are many problems with...
-
‘Acridines’ as New Horizons in Antifungal Treatment
PublikacjaFrequent fungal infections in immunocompromised patients and mortality due to invasive mycosis are important clinical problems. Opportunistic pathogenic Candida species remain one of the leading causes of systemic mycosis worldwide. The repertoire of antifungal chemotherapeutic agents is very limited. Although new antifungal drugs such as lanosterol 14α-demethylase and β-glucan synthase inhibitors have been introduced into clinical...
-
Effect of Flow Normalization in Micro-Pin-Finned Heat Sink: Numerical Study
PublikacjaThe micro-pin-fin heat sink (MPFHS) is widely employed for the heat transfer enhancement of microchannel heat sinks. In the current paper, the effect of flow normalization on the thermohydraulic performance of micro-pin-finned heat sinks is studied numerically. Two geometries of MPFHSs, the conventional design micro-pin-fin heat sink (CD-MPFHS) with a uniform-width micro pin fin and the proposed design micro-pin-fin heat sink (PD-MPFHS)...
-
The impedance of hydrogen oxidation reaction in a proton exchange membrane fuel cell in the presence of carbon monoxide in hydrogen stream
PublikacjaEvaluation of performance of a proton exchange membrane fuel cell, which is affected by carbon monoxide that pollutes the hydrogen stream, was presented. This influence was studied for carbon monoxide concentration of 125–325 ppb, which are close to values specified in ISO 14687:2019 standard. Performed studies provided crucial information for further development of fuel cell as an energy source for automotive application. Impedance...
-
Energy Demand of Short-Range Inland Ferry with Series Hybrid Propulsion Depending on the Navigation Strategy
PublikacjaInterest in hybrid propulsion systems that can be used on small vessels has increased significantly in recent years. They can replace inefficient and environmentally burdensome conventional systems based on diesel engines. Hybrid propulsion has many advantages such as high energy efficiency and virtually noiseless operation, and therefore it fits well with the current trends of “green shipping” and “zero emission”. The aim of the...
-
Experimental Study on Dynamics of Wooden House Wall Panels with Different Thermal Isolation
PublikacjaWood frame buildings are very popular in regions that are exposed to different dynamic excitations including earthquakes. Therefore, their seismic resistance is really important in order to prevent structural damages and human losses. The aim of the present paper is to show the results of experimental tests focused on the dynamic response of wall panels of a wooden frame building with thermal isolation made of mineral wool and...
-
The Application of Granulated Expanded Glass Aggregate with Cement Grout as an Alternative Solution for Sub-Grade and Frost-Protection Sub-Base Layer in Road Construction
PublikacjaThe purpose of the research was to assess the possibility of using granulated expanded glass aggregate (GEGA) with cement grout as a replacement of a sub-grade and frost-protection layer, made of natural fine aggregates (NATU), stabilized with a hydraulic binder. Instead of traditional parts of the road construction, such as the sub-grade and frost-protection layer with the application of fine aggregate, stabilized with cement,...
-
Submicron inorganic particles as an additional filler in hybrid epoxy matrix composites reinforced with glass fibres
PublikacjaIn this study, the effect of selected submicron metal oxide (zinc oxide, titanium oxide) or non-metal oxide (silicon dioxide) particles on mechanical and thermo-mechanical properties of epoxy/glass composites was investigated. The applied epoxy resin was a diglycidyl ether of bisphenol-A cured with triethylenetetramine. As a reinforcement twill weave E-glass fabric was used. Hybrid composites (contained particulate and fibrous...
-
Evaluating the antibacterial activity of muramyl dipeptide derivatives, retro-tuftsin derivatives, and anthraquinone oligopeptides against a range of pathogenic bacteria
PublikacjaSearch for new and efficient antibiotic is crucial because of microbial drug resistance and problems with side effects of the administered medication. In this study, we evaluate the in vitro microbiological activity of muramyl dipeptide derivatives, retro-tuftsin derivatives (i.e., tuftsin with reversed amino acid sequences), and combinations of retro-tuftsin derivatives with substituted anthraquinones. The potency of the investigated...
-
More than just a beer—the potential applications of by-products from beer manufacturing in polymer technology
PublikacjaBeer is the most popular alcoholic beverage in the world, and its popularity is continuously growing. Currently, global beer production is estimated at around 2 billion hectoliters. Nevertheless, the increasing production capacity implicates the rising issue of generated by-products—brewers’ spent grain, spent hops, spent yeast, and wastewater. They are generated in massive amounts, so having in mind the current pro-ecological...
-
High-performance anode-supported solid oxide fuel cells with co-fired Sm0.2Ce0.8O2-δ/La0.8Sr0.2Ga0.8Mg0.2O3−δ/Sm0.2Ce0.8O2-δ sandwiched electrolyte
PublikacjaIn this study, intermediate-temperature solid oxide fuel cells (IT-SOFCs) with a nine-layer structure are constructed via a simple method based on the cost-effective tape casting-screen printing-co-firing process with the structure composed of a NiO-based four-layer anode, a Sm0.2Ce0·8O2-δ(SDC)/La0·8Sr0.2Ga0.8Mg0·2O3−δ (LSGM)/SDC tri-layer electrolyte, and an La0·6Sr0·4Co0·2Fe0·8O3-δ (LSCF)-based bi-layer cathode. The resultant...
-
Switched-capacitor DC-DC converters in arbitrary switching mode - topologically derived resistive models based on incremental graph approach.
PublikacjaIn the preceding paper we reviewed some of modeling approaches aimed at systematic formulation and solution of switched capacitor DC-DC converters. In our review, special attention was paid to computationally efficient and mathematically elegant methods. In so doing we had tried to demonstrate the virtues of unified Incremental Graph (IG) approach. Incremental Graph is, in concept, a tool originally created for analysis and synthesis...
-
Biomechanical testing of bioactive bone cements – a comparison of the impact of modifiers: antibiotics and nanometals
PublikacjaApart from its bone filler and fracture stabilizing function, bone cement can be used as a carrier of bioactive substances, and such modified bone cement can protect the implant against microorganisms, treat local infections and combat bacteria introduced during the surgical procedure. In this paper, the effects of modifying antibiotics and nanosilver on the biomechanical properties of bone cement were examined. The following tests...
-
The influence of the fuel spray nozzle geometry on the exhaust gas composition from the marine 4-stroke diesel engine
PublikacjaThe paper presents experimental research on a 4-stroke, 3-cylinder, turbocharged AL25/30 Diesel engine. Research consisted in investigating the effect of the geometry of the fuel injectors on the exhaust gas composition from the engine. During measurements, the engine was operated with a regulator characteristic of a load range from 40 kW to 280 kW, made by electric water resistance. The engine was mechanically coupled to the electric...
-
Properties of Old Concrete Built in the Former Leipziger Palace
PublikacjaThis research aims to determine the mechanical, chemical, and physical properties of old concrete used in the former Leipziger Palace in Wrocław, Poland. The cylindrical specimens were taken from the basement concrete walls using a concrete core borehole diamond drill machine. The determination of the durability and strength of old concrete was based on specified chosen properties of the old concrete obtained through the following...
-
Regulated Control of the Assembly and Diversity of LPS by Noncoding sRNAs
PublikacjaThe outer membrane (OM) of Gram-negative bacteria is asymmetric due to the presence of lipopolysaccharide (LPS) facing the outer leaflet of the OM and phospholipids facing the periplasmic side. LPS is essential for bacterial viability, since it provides a permeability barrier and is a major virulence determinant in pathogenic bacteria. In Escherichia coli, several steps of LPS biosynthesis and assembly are regulated by the RpoE...
-
Examination of cyp51A and cyp51B expression level of the first Polish azole resistant clinical Aspergillus fumigatus isolate
PublikacjaAspergillus fumigatus is one of the most prevalent airborne fungal pathogens causing infections worldwide. Most A. fumigatus strains are susceptible to azoles, which are administered as the first line therapeutics. However, during last decade the acquired resistance to triazoles by these species has been described. There is a number of publications concerning the examination of clinical A. fumigatus strains from different countries,...
-
The influence of screw configuration and screw speed of co-rotating twin screw extruder on the properties of products obtained by thermomechanical reclaiming of ground tire rubber
PublikacjaThe results of our investigations on the process of continuous thermomechanical reclaiming of ground tire rubber (GTR) carried out using a twin screw extruder are presented.We used a co-rotating twin screw extruder with a special configuration of plasticizing unit, enabling generation of considerable shear forces. The influence of screw configuration and screw speed on breaking of chemical crosslink bonds contained in ground tire...
-
Waterborne polyesters partially based on renewable resources
PublikacjaA new experimental approach for preparing biobased, water-soluble polyesters via titanium(IV) n-butoxide-catalyzed bulk polycondensation is presented. In the described method polymers were obtained from isosorbide, maleic anhydride and poly(ethylene glycol). The chemical structure of the synthesized polyesters was confirmed using 2D NMR spectroscopy and by titration methods. Careful analysis of 2D NMR spectra viz. Correlation Spectra...
-
Noise and Electro-Ultrasonic Spectroscopy of Conducting PolymerThick Films
PublikacjaThick conducting films based on conducting polymer are characterized by DC conductivity and noise in temperature range 10 to 300 K. Conducting polymers could be used e.g. for the top electrode (cathode) in the solid tantalum or niobium capacitors. On the conducting polymer layer the top layer of carbon/graphite and/or silver polymer based pastes is applied in the capacitor technology. Our samples structure consists of conducting...
-
Optimization of boron-doping process of titania nanotubes via electrochemical method toward enhanced photoactivity
PublikacjaIn this work, we were focused on the development of the electrochemical approach resulting in a stable boron doping of titania nanotubes. The doping procedure concerns anodic polarization of as-anodized titania in a H3BO3 solution acting as n boron precursor. The series of attempts were taken in order to elaborate the most beneficial doping conditions. The parameters of electrochemical doping allowing to obtain boron-doped titania...
-
Current Trends in Wick Structure Construction in Loop Heat Pipes Applications: A Review
PublikacjaThermal control systems have been introduced as an important part of electronic devices, enabling thermal management of their electronic components. Loop heat pipe (LHP) is a passive two-phase heat transfer device with significant potential for numerous applications, such as aerospace applications, high-power LEDs, and solar central receivers. Its advantages are high heat transfer capability, low thermal resistance, long-distance...
-
Glutathione-mediated conjugation of anticancer drugs: an overview of reaction mechanisms and biological significance for drug detoxification and bioactivation.
PublikacjaThe effectiveness of many anticancer drugs depends on the creation of specific metabolites that may alter their therapeutic or toxic properties. One significant route of biotransformation is a conjugation of electrophilic compounds with reduced glutathione, which can be non-enzymatic and/or catalyzed by glutathione-dependent enzymes. Glutathione usually combines with anticancer drugs and/or their metabolites to form more polar...
-
Tyre/road noise measurements on ISO tracks according to the UNECE Regulation 117
PublikacjaWithin the Polish-Norwegian research project ELANORE, a limited Round Robin Test has been performed on 3 ISO tracks in Northern Europe. The basic objective of the project is to improve the EU directive on labelling of tyres for noise and rolling resistance, and this directive is based on the measurement procedures defined in the UN ECE Reg.117. The same test car, test tyres and measurement equipment as well as personnel were used...
-
Representativity of ISO test track surface based on controlled pass-by measurements
PublikacjaWithin the Polish-Norwegian research project ELANORE, a limited Round Robin Test has been performed on four ISO tracks in Northern Europe. The basic objective of the project is to improve the EU directive on labelling of tyres for noise and rolling resistance. This directive is based on the measurement procedures proscribed in the UNECE Reg.117. Measurements on 3 ISO tracks were performed in 2021 and presented at InterNoise 2022....
-
The Use of Direct Shear Test for Optimization of Interlayer Bonding Under a Poroelastic Layer
PublikacjaPoroelastic Road Surfaces (PERS) are characterised by porous structure with air void content of 20% or higher and stiffness almost 10 times lower than that of a standard asphalt course. Such properties enable noise reduction by up to 12 dB in comparison to SMA 11 mixture. However, the disadvantage of a poroelastic pavement is its low durability, which partially results from delamination from the lower layer. The paper aims to investigate...
-
Bitumen-Based Poroelastic Pavements: Successful Improvements and Remaining Issues
PublikacjaThis article presents the development process of designing and testing poroelastic pavement based on highly polymer-modified bitumen. Poroelastic wearing course was composed of mineral and rubber aggregate mixed with highly polymer-modified bitumen, in contrast to previous trials, during which polyurethane resins were mainly used as binder, which led to several serious technological problems concerning difficult production, insufficient...
-
Comparative Analysis of Unmanned Aerial Vehicles Used in Photogrammetric Surveys
PublikacjaThere are many manufacturers on the market offering various types of Unmanned Aerial Vehicles (UAV). The multitude of drones available on the market means that the choice of a UAV for a specific application appears to be a decision problem to be solved. The aim of this article is a comparative analysis of drones used in photogrammetric surveys. The criteria for evaluating the UAVs were: availability and product support, payload...
-
Presence of antibiotics in the aquatic environment in Europe and their analytical monitoring: Recent trends and perspectives
PublikacjaThe presence of antibiotics and their metabolites in the aquatic environment exerts a negative impact on all organisms. Moreover, the easy migration of these substances to drinking water may also have serious consequences for public health, such as drug resistance. Although antibiotics and their metabolites are detected in surface waters and wastewater, there are still no systemic solutions preventing environmental pollution with...
-
Oxidation and hydrogen behavior in Zr-2Mn alloy
PublikacjaThe purpose of the present research was to determine the oxidation and hydrogenation behavior in the new Zr-2Mn alloy. The oxidation of alloy was performed at temperatures between 350°C and 900°C for 30 minutes. The hydrogen charging was made for 72 h at a current density 80 mA/cm2. The charged samples were heat treated at 400°C for 4 h to obtain a uniform hydrogen profile content across the sample. The oxidation resulted in an...
-
Multifrequency Nanoscale Impedance Microscopy (m-NIM): A novel approach towards detection of selective and subtle modifications on the surface of polycrystalline boron-doped diamond electrodes
PublikacjaIn this paper, we describe the modification of Nanoscale Impedance Microscopy (NIM), namely, a combination of contact-mode atomic force microscopy with local impedance measurements. The postulated approach is based on the application of multifrequency voltage perturbation instead of standard frequency-by-frequency analysis, which among others offers more time-efficient and accurate determination of the resultant impedance spectra...
-
Effect of Ethanol Extracts of Propolis (EEPs) against Staphylococcal Biofilm—Microscopic Studies
PublikacjaStaphylococci growing in the form of biofilm exhibit high resistance to a plethora of antibiotics. The aim of the study was to assess the influence of ethanolic extract of propolis (EEPs) on S. epidermidis ATCC 35984 biofilm using fluorescent microscopy. Propidium iodide (PI) and SYTO 9 were used for differentiation of live and dead cells, and calcofluor white was used to stain the extracellular matrix, the self-produced extracellular...
-
Retrievable strain measuring system in screw displacement piles - readings and results interpretation problems
PublikacjaStatic load tests on foundation piles are generally carried out in order to determine load – displacement characteristic of the pile. For more detailed information, e.g. force distribution along the shaft, load transfer mechanism and characteristics of soil-structure interaction (unit resistance curves t-z, q-z) additional pile instrumentation is required. Most popular techniques focus on direct concrete strain measurements and...
-
Polymer journal bearings behaviour research under limited lubrication and cooling conditions conducted on high torque test rig
PublikacjaPolymer journal bearings are frequently used as a water-lubricated bearings of small marine units’ propeller shafts . Choice of these bearings is based on their simple construction and relatively low purchase and maintenance costs. Although properly designed and installed water lubricated bearings may well last for over a decade, rapid wear or failure of these bearings can be observed...
-
Potential applications of by-products from the coffee industry in polymer technology – Current state and perspectives
PublikacjaCoffee is one of the most popular beverages in the world, and its popularity is continuously growing, which can be expressed by almost doubling production over the last three decades. Cultivation, processing, roasting, and brewing coffee are known for many years. These processes generate significant amounts of by-products since coffee bean stands for around 50% of the coffee cherry. Therefore, considering the current pro-ecological...
-
Investigating the effects of structural pounding on the seismic performance of adjacent RC and steel MRFs
PublikacjaAn insufficient separation distance between adjacent buildings is the main reason for structural pounding during severe earthquakes. The lateral load resistance system, fundamental natural period, mass, and stiffness are important factors having the influence on collisions between two adjacent structures. In this study, 3-, 5- and 9-story adjacent reinforced concrete and steel Moment Resisting Frames (MRFs) were considered to investigate...
-
Chemical, Physical, and Mechanical Properties of 95-Year-Old Concrete Built-In Arch Bridge
PublikacjaThis research aimed to determine the durability and strength of an old concrete built-in arch bridge based on selected mechanical, physical, and chemical properties of the concrete. The bridge was erected in 1925 and is located in Jagodnik (northern Poland). Cylindrical specimens were taken from the side ribs connected to the top plate using a concrete core borehole diamond drill machine. The properties of the old concrete were...
-
Shape-Memory Polyurethane Polymers
PublikacjaPolyurethanes (PUs) are one of the most widely used polymers in research and industry. They can be synthesized from chemical sources and natural sources. PUs are a very useful class of polymers and exhibit many desirable properties that can be exploited in various applications. PUs are formed by the reaction between polyols and isocyanates. A wide variety of polyols and isocyanates are available for synthesis, and hence we can...
-
PERS - QUIET ROAD SURFACE FOR URBAN AREAS
PublikacjaTraffic noise is one of the most important environmental problems in densely populated urban areas. At low speeds the tyre/road interaction dominates all other sources. It is anticipated that when electric and hybrid vehicles gain dominance in city traffic, the importance of tyre/road noise will still increase as electric engines are much less noisy than combustion engines. On the other hand, electric and hybrid urban vehicles...
-
Study of the Anti-Staphylococcal Potential of Honeys Produced in Northern Poland
PublikacjaThe antimicrobial activity of 144 samples of honeys including 95 products from apiaries located in Northern Poland was evaluated. The antibacterial activity of those natural products, their thermal stability, and activity in the presence of catalase was investigated by microdilution assays in titration plates. The MTT assay was performed for the determination of anti-biofilm activity. Spectrophotometric assays were used for the...
-
The adaptive backstepping control of PMSM supplied by current source inverter for the field weakening region
PublikacjaThe sensorless control system of permanent magnet synchronous motor PMSM supplied by current source inverter for field weakening operation is presented in this paper. The adaptive backstepping control system and the backstepping speed observer are presented. The control system is based on multi-scalar variables. The control variables are: dc-link voltage and the output current vector pulsation. The control system was named voltage...
-
Revisiting The Determination Of Cutting Power While Sawing Of Wood With Circular Saw Blades By Means Of Fracture Mechanics
PublikacjaIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (power) could be considered from a point of view of modern fracture mechanics. Cutting forces may be employed to determine not only toughness...
-
Design of a Shape-Memory-Alloy-Based Carangiform Robotic Fishtail with Improved Forward Thrust
PublikacjaShape memory alloys (SMAs) have become the most common choice for the development of mini- and micro-type soft bio-inspired robots due to their high power-to-weight ratio, ability to be installed and operated in limited space, silent and vibration-free operation, biocompatibility, and corrosion resistance properties. Moreover, SMA spring-type actuators are used for developing different continuum robots, exhibiting high degrees...
-
Enhanced Spectroscopic Insight into Acceptor-Modified Barium Strontium Titanate Thin Films Deposited via the Sol–Gel Method
PublikacjaIn the present paper, composite thin films of barium strontium titanate (BaxSr1−xTiO3) with an acceptor modifier (magnesium oxide—MgO) were deposited on metal substrates (stainless steel type) using the sol–gel method. The composite thin films feature BaxSr1−xTiO3 ferroelectric solid solution as the matrix and MgO linear dielectric as the reinforcement, with MgO concentrations ranging from 1 to 5 mol%. Following thermal treatment...
-
Experimental research on over-laminated steel sandwich panel connection to determine the form of fatigue failure
PublikacjaThe novel means of transport need to meet rising both the economic and ecologic requirements. In recent years the International Maritime Organization (IMO) introduced new measure of ship energy efficiency (the EEDI index), as well as new regulations regarding higher quality of fuel (so called Tier limits). It resulted in much higher interest of the technological development of ships. One of the solution having great potential is...
-
Influence of Bitumen Type and Asphalt Mixture Composition on Low-Temperature Strength Properties According to Various Test Methods
PublikacjaIn regions with low-temperatures, action transverse cracks can appear in asphalt pavements as a result of thermal stresses that exceed the fracture strength of materials used in asphalt layers. To better understand thermal cracking phenomenon, strength properties of different asphalt mixtures were investigated. Four test methods were used to assess the influence of bitumen type and mixture composition on tensile strength properties...
-
Laboratory fatigue assessment of large geocomposite-reinforced double-layered asphalt concrete beams
PublikacjaGeosynthetic reinforcement of asphalt layers has been used for several decades. Evaluation of the influence of these materials on pavement fatigue life is still ongoing, especially for new types of geocomposites. This paper presents the evaluation of fatigue performance of large asphalt concrete beams reinforced with a new type of composite in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions...
-
May Staphylococcus lugdunensis Be an Etiological Factor of Chronic Maxillary Sinuses Infection?
PublikacjaStaphylococcus lugdunensis is an opportunistic pathogen found in the healthy human skin microbiome bacterial community that is able to cause infections of diverse localization, manifestation, and course, including laryngological infections, such as necrotizing sinusitis. Chronic maxillary sinusitis is a disease present in up to one third of European and American populations, and its etiology is not fully described. Within this...
-
Probiotic potential of Bacillus Isolates from Polish Bee Pollen and Bee Bread
PublikacjaThe main goal of this study was the evaluation of the probiotic potential of 10 Bacillus spp. strains isolated from 5 bee bread and 3 bee pollen samples. The antagonistic interaction with Staphylococcus aureus and Escherichia coli was a primary criterion for the preliminary selection of the isolates. Three out of ten strains—PY2.3 (isolated from pollen), BP20.15 and BB10.1 (both isolated from bee bread)—were found to be possible...
-
Fe-modified Mn2CuO4 spinel oxides: coatings based on abundant elements for solid oxide cell interconnects
PublikacjaThe current state of the art steel interconnect coating materials are based on critical raw material - Co-oxide spinels. Replacing Co-oxide spinels with alternative, abundant materials can reduce the dependence on the critical raw materials. Cobalt-free coatings with the general formula Mn2-xCuFexO4, where x = 0, 0.1, 0.3, were electrophoretically deposited on a ferritic stainless-steel support and evaluated. Prior to deposition,...