Filtry
wszystkich: 160
wybranych: 147
Wyniki wyszukiwania dla: ADDITIVES
-
Structure and thermoelectric properties of bismuth telluride—Carbon composites
PublikacjaCarbon nanotubes and amorphous carbon have been introduced into a bismuth telluride matrix (0.15 and 0.30 wt.% ratio) to investigate the influence of the carbon on the composite’s thermoelectric properties. Composites with well-dispersed additives have been obtained by sonication and ball-milling methodology. Carbon nanotubes and an amorphous carbon addition led to a decrease in electric conductivity from 1120 S/cm to 77 S/cm....
-
Effect of some organic solvent - water mixtures composion on precipitated calcium carbonate in carbonation process
PublikacjaPrecipitated calcium carbonate particles were obtained during carbonation of calcium hydroxide slurry with carbon dioxide. Aqueous solutions of isopropyl alcohol, n-butanol and glycerol were used as solvents. Concentration of organic additives in the reactive mixture was from 0 to 20 % (vol.). Precipitation process were performed in a stirred tank reactor equipped with gas distributor. Multimodal courses of particles size distribution...
-
Research on the separation properties of empty-column gas chromatography (EC-GC) and conditions for simulated distillation (SIMDIS)
PublikacjaThe paper presents the results of investigations on new procedures of determination of selected cleaning additives in diesel fuel. Two procedures: one-step analysis using gas chromatography with flame ionization detection (GC-FID) or mass spectrometry (GC-MS) and a two-step procedure in which normal-phase high-performance liquid chromatography (NP-HPLC) was used for preliminary separation of the additives, were compared. The additive...
-
Maillard-reaction (glycation) of biopolymeric packaging films; principles, mechanisms, food applications
PublikacjaBackground The biodegradable, biocompatible, sustainable, and renewable nature of biomaterials has led to increased interest in developing biopolymeric food packaging films (BFPFs) with green ingredients and strategies. To enhance the performance of these films, biopolymer molecules can be modified or combined with additives like nanomaterials, cross-linkers, bioactive compounds, and other polymers, particularly with Maillard-reaction...
-
Juices from untypical edible fruits as acidity regulators for food industry. Verification of health promoting properties. Comparison with typical acidity regulators.
PublikacjaNowadays all kind of food additives, and among them acidity regulators, have become necessary components of most food products. Their role is lengthening shelf-life, improving the sensory properties and protecting food products from microbial contaminations. However, despite advantages, there are also some undesirable effects of use of food additives that have raised public concern recently. Therefore, food industry considers the...
-
Waste printer ink as modifier for natural rubber/carbon black composites: No haste, use waste
PublikacjaFrom a sustainability perspective, achieving a greener future with a minimal carbon footprint requires maximizing waste materials' reuse. The four pillars of satisfying customer demands are processing, price, properties, and performance. Along with such a global policy, this work seeks to utilize waste printer ink (WPI) as a source of carbon in combination with low- and high-surface carbon black (LCB and HCB, respectively) additives...
-
Quantifying the effective mobilized RAP content during hot in-place recycling techniques
PublikacjaThe utilization of in-place recycling techniques is capable of consuming 100% reclaimed asphalt pavement (RAP). Hot in-place recycling (HIR) is one of the promising techniques to rehabilitate the pavements suffering from minor cracking issues through heat scarification, additive injecting, mechanical mixing, and compacting. However, the main concern of using 100% RAP in HIR remains as how much RAP can be activated and mobilized...
-
Przegląd nanododatków stosowanych w warstwach asfaltowych nawierzchni drogowych
PublikacjaJednym z kierunków rozwoju technologii materiałowych jest nanotechnologia rozumiana jako dziedzina zajmująca się zastosowaniem nanododatków do wytwarzania nowych materiałów oraz ich wpływem na parametry modyfikowanych materiałów. W ostatnich latach nanotechnologia wkracza do technologii modyfikacji asfaltów stosowanych w nawierzchniach drogowych. W artykule przedstawiono stosowane obecnie w budownictwie drogowym nanododatki oraz...
-
Thermal Energy Development in Magnetohydrodynamic Flow Utilizing Titanium Dioxide, Copper Oxide and Aluminum Oxide Nanoparticles: Thermal Dispersion and Heat Generating Formularization
PublikacjaThe main aim of this article heat transfer in thermal engineering deals with the production, use, transformation, and transfer of thermal energy. Engineering and industrial fields including food packaging, the production of food additives, electronic cooling, microturbines, etc. heavily rely on heat transmission. Due to its intriguing potential in industries like the production of polymers, paper, crystal glass, etc., scientists...
-
Analysis of friction ridge evidence for trace amounts of paracetamol in various pharmaceutical industries by Raman spectroscopy
PublikacjaThe detection of potentially harmful substances presents a multifaceted challenge. On one hand, it can directly save lives, on the other, it can significantly aid and enhance police work, thereby increasing the effectiveness of investigations. The research conducted in this study primarily aims to identify paracetamol in fingerprints, considering situations involving direct contact of a person with paracetamol either chronically...
-
Imidazole-Based Lithium Salt LiHDI as a Solid Electrolyte Interphase-Stabilising Additive for Lithium-Conducting Electrolytes
PublikacjaLithium salt LiHDI (lithium 4,5-dicyano-2-(n-heptafluoropropyl)imidazolide) is proposed as a solid electrolyte interphase-stabilising additive for lithium-ion batteries, which can be added in a smaller amount than fluoroethylene carbonate (FEC) and vinylene carbonate (VC) additives. Electrolytes containing either lithium 4,5-dicyano-2-(trifluoromethyl)imidazolide (LiTDI) or battery-standard LiPF6 were tested with various amounts...
-
Investigating the Impact of Curing System on Structure-Property Relationship of Natural Rubber Modified with Brewery By-Product and Ground Tire Rubber
PublikacjaThe application of wastes as a filler/reinforcement phase in polymers is a new strategy to modify the performance properties and reduce the price of biocomposites. The use of these fillers, coming from agricultural waste (cellulose/lignocellulose-based fillers) and waste rubbers, constitutes a method for the management of post-consumer waste. In this paper, highly-filled biocomposites based on natural rubber (NR) and ground tire...
-
Mechanical properties of two-stage concrete modified by silica fume
PublikacjaAbstract. Two-stage concretes, despite the fact that they have proven themselves in various types of construction, have not been studied to the same extent as traditional heavy concretes. Therefore, the article developed the composition of frame concrete with various additives in the composition of the cement-sand mortar. A comparison of the mechanical characteristics of the developed compositions with the addition of silica fume...
-
Renewable Resources for Polyurethanes and Polyurethane Composites: A Review
PublikacjaEach year, more than two million tons of polyurethane is produced in the EU by reacting isocyanates with polyols made from fossil fuel. In addition, there are appreciable quantities of petroleum based functional additives applied in the industry nowadays for both polyols and polyurethane materials. It is therefore of key importance to develop sustainable economically viable polyols with enhanced functionalities, and thereby reducing...
-
Zastosowanie addytywów w separacji pianowej białek serwatkowych i białek mlecznych
PublikacjaZaproponowano proces separacji pianowej do wydzielania białek ze strumieni poprodukcyjnych przemysłu mleczarskiego Ponadto zaproponowano zastosowanie w separacji pianowej białek serwatkowych i mlecznych addytywów dopuszczonych ustawą do stosowania w żywności. Jako cel pracy przyjęto uzyskanie wyników uzasadniających wybór takich addytywów, które intensyfikują przebieg i polepszają wynik procesu separacji pianowej białek. W części...
-
Interactions of selected mono- and disaccharides with precipitated calcium carbonate particles
PublikacjaCalcium carbonate is a widespread compound in nature and it can be produced by living organisms in the biomineralization process. Calcite, aragonite and vaterite are anhydrous polymorphic forms of calcium carbonate, wherein the calcite is the most thermodynamically stable. Vaterite is the metastable crystalline phase, which can be a precursor of calcite and aragonite, because it can easily transformed by dissolution and re crystallization...
-
Klasyfikacja wyrobów tytoniowych z wykorzystaniem elektronicznych nosów
PublikacjaZapobieganie nielegalnej dystrybucji wyrobów tytoniowych w Polsce stanowi poważny problem. Wyroby tytoniowe przemycane do Polski mogą charakteryzować się niższą jakością, wynikającą z wykorzystania surowców gorszego gatunku. Jednym z rozwiązań zmniejszających skalę tego problemu mogą być działania ograniczające przemyt przez granice państwa. Autorzy pracy uważają, że wykorzystanie elektronicznych nosów do rutynowych kontroli przewożonych...
-
Remediation of soils on municipal rendering plant territories using Miscanthus × giganteus
PublikacjaPhytoremediation, as a cost-effective, highly efficient, environmentally friendly, and green approach, gained attention to the removal of metals, including heavy metals, from contaminated soils. The toxic nature of heavy metals can have an adverse effect on human health and the ecosystem, and their removal remains a worldwide problem. Therefore, in this study, a field experiment was carried out to evaluate the potential of Miscanthus × giganteus...
-
Proteolysis of whey protein isolates in nanoemulsion systems: impact of nanoemulsification and additional synthetic emulsifiers
PublikacjaNanoemulsions are currently of interest in the functional food sector because their small droplet size (100–500 nm) provides a number of potential advantages over conventional emulsions. This study concerned the behavior of nanoemulsions stabilized with whey proteins and two synthetic emulsifiers (Tween 80 and Croduret), and exposed to conditions simulating the human upper gastrointestinal tract. In particular, the effect of synthetic...
-
Modification of Ground Tire Rubber—Promising Approach for Development of Green Composites
PublikacjaGround tire rubber (GTR) was mechano-chemically modified using a road bitumen 100/150 and two types of organic peroxides: di-(2-tert-butyl-peroxyisopropyl)-benzene (BIB) and dicumyl peroxide (DCP). The impact of used additives on reactive sintering efficiency and physico-mechanical properties of modified GTR was investigated using oscillating disc rheometer measurements, followed by tensile tests and swelling behavior studies....
-
Laboratory assessment of permeability of sand and biopolymer mixtures
PublikacjaLaboratory assessment of permeability of sand and biopolymer mixtures. This research presents a method of creating seepage barriers in a sandy soil using biopolymer additives (biosubstance), which consist of polysaccharides and water. Polysaccharides strongly interact with water to produce a viscous suspension. The paper aims to investigate the infl uence of a biosubstance employed in a highly permeable sandy soil. Amount of the...
-
Evaluation of adhesive forces and the specific surface energy of zirconia stabilized by yttria with alumina additions ceramic by AFM method
PublikacjaThe adhesive forces and the specific surface energy of ceramic material surfaces are very important for further tribological and biomedical applications of ceramics. Partially stabilized zirconia (zirconium oxide) is popular for manufacturing various medical products. ZrO2 stabilized by Y2O3 with additions of 5 wt% alumina was produced by slip casting method with a subsequent sintering. Structure and chemical composition of ceramic...
-
Polymer electrolytes with ionic liquids
PublikacjaSolid polymer electrolytes are solutions of salts in the macromolecular polymeric compound. Excellent process ability, flexibility, non-flammability and non-reactivity make them ideal materials for electrochemical devices. The problem in their use is limited conductivity. It increases with increasing salt concentration in the polymer, but at the same time the condition is to increase the glass transition temperature of the polymer...
-
Cold-adapted bacterial lipolytic enzymes and their applications
PublikacjaLipolytic enzymes, esterases and lipases catalyze the hydrolysis and transesterification of fatty acid esters. This class of enzymes is the most important group of biocatalysts for biotechnological applications. From this perspective, coldactive lipolytic enzymes from cold adapted bacteria display attractive properties for some industrial purposes, including high catalytic activity at low temperatures and low thermostability. To...
-
New insights of nanomaterials usage toward superhydrophobic membranes for water desalination via membrane distillation: A review
PublikacjaMembrane distillation (MD) is a promising technology for seawater desalination due to the ability to process high-salinity waters and the ability to be driven by low-grade or waste heat. However, practical applications of MD membranes are limited by the low vapor flux and fouling problem. Recently, there is a growing interest in developing novel MD membrane materials with enhanced hydrophobicity to improve the efficiency of desalination...
-
A review on electrospun membranes for potential air filtration application
PublikacjaAir pollution is one of the major environmental concerns in most highly populated cities, which is typically caused by particulate (PM2.5 and PM0.1) or gaseous pollutants that can be removed using electrospun membranes. These membranes are characterized by different features in terms of uniform and controllable structure, tuneable porosity, and high surface area, where their separation efficiency strongly depends on their properties....
-
Manganese Phosphatizing Coatings: The Effects of Preparation Conditions on Surface Properties
PublikacjaManganese phosphate coating could be used to protect the surface of steel products. However, it is essential to determine the effects which process parameters, as well as the types of additives used, have on the efficiency of coating deposition. Thus, we present here a process of phosphatization of low-alloy steel (for 15 min at 95 ◦C) in manganese/nickel baths followed by a passivation process with the use of a silicon and zircon...
-
Analysis of the Possibility of Using New Types of Protective Coatings and Abrasion-Resistant Linings under the Operating Conditions of the Spiral Classifier at KGHM Polska Miedź S.A. Ore Concentration Plant
PublikacjaA study was carried out to select the appropriate coatings for corrosion protection of the spiral classifier working at KGHM Polska Miedź S.A. Ore Concentration Plant. The abrasion resistance of selected protective coatings and wear-resistant linings was investigated using a DT-523 rotary abrasion tester with Taber CS-10 rubber abrasive discs. The average weight loss of the coatings after a cycle of 2000 revolutions was determined....
-
Hydraulic conductivity of a biopolymer treated sand
PublikacjaThis paper presents results of laboratory assessment of creating seepage barriers in a sandy soil using biopolymer additives (bio substance), which consist of polysaccharides and water. Polysaccharides strongly interact with water to produce a viscous suspension. The aim of the conducted work was to investigate the influence of a biosubstance employed in a highly permeable sandy soil. The amount of the biopolymer used in a sample...
-
Potential applications of crude glycerol in polymer technology–Current state and perspectives
PublikacjaThe increasing use of bio-based fuels and fuel additives, among them biodiesel, causes significant surplus of crude glycerol on the market which creates new challenges in terms of its sustainable utilization. A lot of ways for the incorporation of this by-product into different branches of industry requires purification by expensive and complicated processes. Therefore, researchers are seeking for applications of untreated crude...
-
Some geomechanical properties of a biopolymer treated medium sand
PublikacjaSome geomechanical properties of a biopolymer treated medium sand. This paper presents a laboratory assessment of geomechanical properties of sandy soil improved by biopolymer application. Additives (biosubstance) consist of polysaccharides and water. Biosubstance used in the project was xanthan gum, which comes from bacteria Xanthomonas campestris. Triaxial shear compression tests and unconfi ned compression tests were carried...
-
Opinie młodych konsumentów na temat oznakowani opakowań kawy i herbaty
PublikacjaCelem pracy jest poznanie opinii i świadomości młodych konsumentów w zakresie oznakowania opakowań herbaty i kawy w świetle obowiązujących regulacji prawnych. Badanie przeprowadzono wśród 78 studentów trójmiejskich uczelni deklarujących nabywanie i konsumpcję herbaty oraz kawy. Zdecydowana większość respondentów (ponad 90%) stwierdziła, że informacje umieszczane na opakowaniach kawy i herbaty są napisane czytelnie oraz zrozumiałym...
-
Improving carbon dioxide capture in aqueous ammonia solutions by fine SiO2 particles
PublikacjaAmmonia solutions are considered to be effective solvents for carbon dioxide absorption. Despite the numerous advantages of these solvents, their high volatility is a significant technical and economic problem. Therefore, in this work, silica particles were used as additives to improve CO2 absorption and inhibit NH3 desorption. SiO2 microparticles and colloidal SiO2 particles in the concentration range of 0-0.15 wt.% were used...
-
Antibacterial evaluation of bioactive modifiers of bone cements: antibiotics, nanometals and chitosan
PublikacjaModern biomaterials in addition to their basic tasks, can serve as carriers of active substance. The release of a bioactive particles allows to locally fight infection or its prevent it. Bone cements additionally to their basic applications in orthopedic surgery can also serve to deliver locally active substances. Currently, only antibiotics are routinely used as modifiers for bone cements. Bioactive bone cements constitute...
-
Dietary antioxidants as a source of hydrogen peroxide
PublikacjaStudies of 54 antioxidants revealed that 27 of them, mainly polyphenols, generated hydrogen peroxide (H2O2) when added to Dulbecco’s modified Eagle’s medium (DMEM), other media used for culture of mammalian and yeast cells and phosphate-buffered saline. The most active antioxidants were: propyl gallate (PG), (−)-epigallocatechin gallate (EGCG) and quercetin (Q). Chelex treatment and iron chelators decreased H2O2 generation suggesting...
-
Mutagenic and Carcinogenic Compounds in Food
PublikacjaFood is a major environmental human cancer risk factor. One of the reasons for this is that food products contain substances that exhibit mutagenic and carcinogenic potential which may induce the transformation of normal somatic cells into cancerous cells. These compounds occur in food as a result of microbial contaminations (mycotoxins produced by molds), are generated from natural food components upon processing (e.g. heterocyclic...
-
Antibacterial Porous Systems Based on Polylactide Loaded with Amikacin
PublikacjaThree porous matrices based on poly(lactic acid) are proposed herein for the controlled release of amikacin. The materials were fabricated by the method of spraying a surface liquid. Description is given as to the possibility of employing a modifier, such as a silica nanocarrier, for prolonging the release of amikacin, in addition to using chitosan to improve the properties of the materials, e.g., stability and sorption capacity....
-
Composite Materials Based on Silicon Oxycarbide as Anodes for Lithium-Ion Batteries
PublikacjaIn this work, the properties of binary SiOC/graphite and SiOC/tin, as well as ternary SiOC/graphite/tin obtained from various preceramic precursors are described. During the first step, the materials were synthesized using various techniques such as sol-gel and hydrosilylation. To prevent sedimentation and agglomeration of graphite particles during the gelation stage without using surfactants and thickeners, a new gelation technique...
-
Inhibition of Polymer Photodegradation by Incorporation of Coffee Silverskin
PublikacjaOver the last years, the trend associated with the incorporation of materials from renewable resources into polymer technology is getting significantly more vital. Researchers are trying to transfer the properties of natural raw materials into the polymer world. Therefore, different natural materials are more often investigated as potential additives for polymers. Such an effect is noted for the coffee industry by-products, such...
-
Analytical methodologies for determination of artificial sweeteners in foodstuffs- a review
PublikacjaArtificial high-intensity sweeteners are more and more frequently used for food production. Food industry tends to highlight beneficial aspects of their use, such as tooth-friendliness, rising-up quality of life of those suffering from different forms of diabetes and possibility of weight control without sacrificing favorite unhealthy drinks or snacks. On the other hand some of the consumers are deeply concerned about safety of...
-
Green Polymer Nanocomposites for Skin Tissue Engineering
PublikacjaFabrication of an appropriate skin scaffold needs to meet several standards related to the mechanical and biological properties. Fully natural/green scaffolds with acceptable biodegradability, biocompatibility, and physiological properties quite often suffer from poor mechanical properties. Therefore, for appropriate skin tissue engineering and to mimic the real functions, we need to use synthetic polymers and/or additives as complements...
-
Biopolymer-based composites for tissue engineering applications: A basis for future opportunities
PublikacjaBiomimetic scaffolds supporting tissue regeneration are complex materials with multifunctional characteristics. The unique biocompatibility and biodegradability of biopolymers make them excellent candidates for tissue engineering and regenerative medicine. Biopolymers, which have a wide range of properties, can be obtained from different natural sources. Depending on the target tissue, biopolymers can be engineered to meet a series...
-
Correlation between partial inhibition of hydrogen evolution using thiourea and catalytic activity of AB5-type hydrogen storage alloy towards borohydride electrooxidation
PublikacjaDirect borohydride fuel cells (DBFCs) are devices which directly convert the chemical energy stored in the borohydride ion and oxidant into electrical energy as a result of redox reactions. Unfortunately, a significant amount of fuel is lost as a result of the undesirable hydrolysis reaction. The selection of an efficient borohydride hydrolysis inhibitor requires detailed knowledge regarding the interaction mechanism between the...
-
Effect of selected ammonia escape inhibitors on carbon dioxide capture and utilization via calcium carbonate precipitation
PublikacjaCarbon dioxide was used to precipitate CaCO3 with CaCl2 solution in the presence of NH3 as a CO2 absorption promoter. Compounds that were previously indicated as inhibitors of ammonia escape during CO2 absorption were also added to the reaction mixture. Inorganic salts, i.e. ZnCl2, CuCl2, CoCl2, and organic substances, i.e. glycerol, ethylene glycol and triethanolamine were tested inhibitors in this work. A model post-distillation...
-
More than just a beer—the potential applications of by-products from beer manufacturing in polymer technology
PublikacjaBeer is the most popular alcoholic beverage in the world, and its popularity is continuously growing. Currently, global beer production is estimated at around 2 billion hectoliters. Nevertheless, the increasing production capacity implicates the rising issue of generated by-products—brewers’ spent grain, spent hops, spent yeast, and wastewater. They are generated in massive amounts, so having in mind the current pro-ecological...
-
The Thin-Layer Microchromatography (μTLC) and TLC–FID Technique as a New Methodology in the Study of Lubricating Oils
PublikacjaThis paper concerns the possibility of using TLC coupled with a flame ionization detector (FID) and micro-TLC (μTLC) as precursors for microfluidized devices of analytical techniques to identify and determine the presence and content of the petroleum/vegetable oil base in the lubricating oils applied in cutting devices (chainsaws). This research is related to the problem of ensuring, in compliance with the requirements of environmental...
-
Technological aspects of manufacturing polymer packaging materials degradable in seawater environment
PublikacjaIn recent years, the number of polymer materials used in the food packaging market was growing extremely fast. This contributed to depletion of non-renewable resources and more intense degradation of the environment due to resistant polymer. Therefore, such a dramatic situation has forced researchers to look for biodegradable materials, decomposable under action of microorganism. Currently, only a small number of researches examine...
-
Finite-element analysis of a base-isolated multi-storey steel building under seismic motions
PublikacjaNumerical simulation of the seismic behaviour of a multi-storey steel building, both fixed-base and base-isolated, under the 1940 El Centro earthquake was performed in this paper. The analyzed 4-storey building was decoupled from the shaking ground with the Polymeric Bearings, which can be considered a proposal of a new seismic isolation system. It consists of rectangular-shaped blocks made of a specially prepared flexible polymeric...
-
Experimental and Numerical Investigations of the Effect of Curing Conditions on the Temperature Rise of Concrete
PublikacjaThis paper presents experimental and numerical studies investigating the impact of three curing conditions on temperature evolution in concrete cubes. The tests were performed on samples of the same volume (3.375 dm3) under different curing conditions: room temperature, insulation boxes, and adiabatic calorimeter. Various cements (Portland cement, Portland composite cement, and blast furnace slag cement) and aggregates (gravel...
-
Wytwarzanie i modyfikacja powierzchni porowatych struktur tytanowych przeznaczonych na implanty
PublikacjaCelem pracy było wytworzenie stopu Ti-13Nb-13Zr z wykorzystaniem technologii selektywnego topienia laserowego (SLM) oraz jego biofunkcjonalizacja za pomocą utleniania mikrołukowego (MAO), a następnie określenie wpływu parametrów procesowych na właściwości otrzymanych materiałów pod kątem ich zastosowania na implanty. Oceniono wpływ napięcia, natężenia i czasu procesu MAO przeprowadzanego w elektrolicie zawierającym wapń i fosfor...