Filtry
wszystkich: 848
wybranych: 711
Wyniki wyszukiwania dla: MECHANICAL SYSTEM
-
Impact of laser beam welding on mechanical behaviour of 2.25Cr–1Mo (P22) steel
PublikacjaThe use of welding processes in the manufacturing and repair of structures intended for the energy industry plays a key role in the guarantee of a continuous supply of fossil fuels, which is the basic condition for ensuring energy security. A square butt joint of 10 mm thick plate of 2.25Cr–1Mo (P22) steel was fabricated by autogenous laser beam welding process and then post-weld heat treatment (PWHT) for two sets of process parameters...
-
Experimental and Numerical Study on Mechanical Characteristics of Aluminum/Glass Fiber Composite Laminates
PublikacjaThe fiber-metal composites made of aluminum sheets and glass fibers reinforced with a polyester resin as the matrix were studied. The composites were prepared by hand lay-up method. Some aspects of manufacturing affecting the composite behavior were considered. In particular, the influences of the arrangement of layers and their number on the mechanical and physical properties of composites with ten different compositions were...
-
Influence of Different Nanometals Implemented in PMMA Bone Cement on Biological and Mechanical Properties
PublikacjaCemented arthroplasty is a common process to fix prostheses when a patient becomes older and his/her bone quality deteriorates. The applied cements are biocompatible, can transfer loads, and dampen vibrations, but do not provide antibacterial protection. The present work is aimed at the development of cement with antibacterial effectivity achieved with the implementation of nanoparticles of different metals. The powders of Ag,...
-
Effect of Laser Treatment on Intrinsic Mechanical Stresses in Titanium and Some of Its Alloys
PublikacjaLaser surface treatment conducted at different power levels is an option to modify titanium bone implants to produce nano- and microtopography. However, such processing can lead to excess mechanical stress within the surface layer. This research aims to calculate the level of such residual stresses after the surface processing of Ti grade IV, Ti15Mo, and Ti6Al7Nb alloys with an Nd:YAG laser. Light and scanning electron microscopies...
-
Mechanical behaviour of the implant used in human hernia repair under physiological loads
PublikacjaIn laparoscopic operations of abdominal hernias some recurrences still take place, even when applying a surgical mesh. This is usually caused by a failure of the connection between the tissue and the implant. The study deals with the influence of an implant’s orientation on forces in joints, which connect the mesh to human tissues. In the paper, the implant is modelled as a membrane structure within framework of the Finite Element...
-
Balancing energy processes in turbine engines
PublikacjaThe article discusses the issue of balancing energy processes in turbine engines in operation in aeronautic and PDULQHSURSXOVLRQV\VWHPVZLWKWKHDLPWRDQDO\VHDQGHYDOXDWH EDVLFRSHUDWLQJSDUDPHWHUV7KH¿UVWSDUWSUHVHQWV the problem of enormous amounts of energy needed for driving fans and compressors of the largest contemporary turbofan engines commonly used in long-distance aviation. The amounts of the transmitted power and the effect RIÀRZSDUDPHWHUVDQGFRQVWUXFWLRQDOSURSHUWLHVRIWKHHQJLQHV RQWKHLUSHUIRUPDQFHDQGUHDOHI¿FLHQF\DUH evaluated....
-
Efficiency of thermomechanical reclaiming of ground tire rubber conducted in counter-rotating and co-rotating twin screw extruder
PublikacjaIn this article the results of research on a continuous thermomechanical reclaiming process of ground tire rubber (GTR) conducted in a twin screw extruder are presented. The effects of the rotation direction (co-rotating/counter-rotating), design of co-rotating plasticizing units and the rotational speed of the screws on the extruder working parameters, sol fraction and the degree of reclaiming in the obtained products were described....
-
INFLUENCE OF PRESERVATIVE ON THE TENSILE STRENGTH OF THE TISSUE OF PORCINE CIRCULATORY SYSTEM
PublikacjaCurrently one of the leading causes of death worldwide is heart diseases which include calcification of heart valves and vascular aneurysm. There are many biomaterials that can substitute pathologically altered tissue, however, none of them is as perfect as native tissue. Currently, scientists are looking for new biomaterials that can be successfully implanted without exposing the patient to reoperation. Each material introduced...
-
Influence of the low ambient temperature on the start-up process of hydraulic pumps
PublikacjaStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of pressure drop in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump working chambers with...
-
Nonlinear model of a synchronous generator for analysis of more electric aircraft power systems
PublikacjaA nonlinear model for studying a variable-speed synchronous generator (SG) in more electric aircraft (MEA) power system has been developed. The saturation effects of the SG magnetic circuit have been considered. The model has been implemented in the Synopys/Saber simulation environment. The modelling language MAST has been used to elaborate the SG model. The model exhibit a network with the same number of external terminals/ports...
-
Faults and Fault Detection Methods in Electric Drives
PublikacjaThe chapter presents a review of faults and fault detection methods in electric drives. Typical faults are presented that arises for the induction motor, which is valued in the industry for its robust construction and cost-effective production. Moreover, a summary is presented of detectable faults in conjunction with the required physical information that allow a detection of specific faults. In order to address faults of a complete...
-
Intelligent monitoring the vertical dynamics of wheeled inspection vehicles
PublikacjaThe problem of intelligent monitoring of the vertical dynamics of wheeled inspection vehicles is addressed. With the independent MacPherson suspension system installed, the basic analysis focuses on the evaluation of the parameters of the so-called quarter car model. To identify a physically motivated continuous description, in practice, dedicated integral-horizontal filters are used. The obtained discrete model, which retains...
-
Novel Desorber for Online Drilling Mud Gas Logging
PublikacjaThis work presents the construction solution and experimental results of a novel desorber for online drilling mud gas logging. The traditional desorbers use mechanical mixing of the liquid to stimulate transfer of hydrocarbons to the gaseous phase that is further analyzed. The presented approach is based on transfer of hydrocarbons from the liquid to the gas bubbles flowing through it and further gas analysis. The desorber was...
-
Whether Carbon Nanotubes Are Capable, Promising, and Safe for Their Application in Nervous System Regeneration. Some Critical Remarks and Research Strategies
PublikacjaCarbon nanotubes are applied in or considered for different fields of medicine. Among them is the regeneration or rebuilding of nervous system components, which still lack substantial progress; this field is supported by carbon nanotubes to a great extent as the principal material. The limited research on this issue has involved PU/silk/MWCNTs, PCL/silk/MWCNTs, PCL/PGS/CNTs, chitin/CNTs, PGF/CNTs, CNTs/PGFs/PLDLA,MWCNTs chitosan,MWCNTs/PPy,...
-
Styrene-Butadiene Rubber/Modified Ground Tire Rubber Blends Co-Vulcanization: Effect of Accelerator Type
PublikacjaGround tire rubber was thermo-mechanically modified with using a co-rotating twin screw extruder. Modification of GTR was conducted in autothermal conditions. Styrene-butadiene rubber and modified ground tire rubber blends were prepared via two-roll milling. Obtained compounds were cured with conventional system (sulfur/vulcanization accelerator ratio was 2:1). During this research three commonly vulcanization accelerators (MBT,...
-
The Influence of Siliceous Mineral Phases on the Mechanical Properties of Transitional Rocks in the Belchatow Lignite Deposit
Publikacja -
Modification of microporous polyurethane elastomers with different types of ash—morphological, mechanical, and thermal studies
PublikacjaIncorporation of wood ash particles from wood gasification into microporous polyurethane elastomers has been investigated and compared to addition of commercially available microspheres resulting from coal burning. Samples were modified with 3 and 6 wt% of fillers. Structure, mechanical, and thermal properties of obtained elastomers were investigated. Incorporation of both types of ash particles decreased the density of polyurethanes...
-
Investigation on thermal changes of mechanical properties of textile fabric of National Stadium in Warsaw roof
PublikacjaSubject of the research is investigation of mechanical properties of technical fabric Précontraint 1202 S2 used for construction of the mobile part of roof of National Stadium in Warsaw. The research has been focused on fabric behavior in low temperature conditions. The main question which had to be answer has been: is it save to open and close the roof or keep the roof in the close position in winter conditions?
-
DYNAMIC MECHANICAL BEHAVIOUR OF GFRP COMPOSITES WITH SiO2 NANO PARTICLES REINFORCED EPOXY MATRIX
PublikacjaDynamic mechanic (DMA) tests were performed to compare the mechanical behaviour of glass fibre reinforced epoxy laminate composites with SiO2 nanoparticle reinforced matrix. The selection of the most promising nanoparticle concentrations was considered in terms of elastic modulus and glass transition temperature. The reference specimens (0% nanoparticles) did not contain diluent accordingly the results do not allow the exact comparison...
-
Selected mechanical properties of steam kiln-dried wood determined on the basis of cutting power
PublikacjaW artykule przedstawiono wyniki wiązkości oraz naprężeń granicznych przy ścinaniu drewna suszonego z użyciem pary wodnej na podstawie zmierzonych wartości mocy skrawania. Badaniom poddawano próbki dębowe oraz sosnowe pochodzące z północnych regionów Pomorza. Wykazano, że przyspieszone suszenie drewna z użyciem pary wywołuje obniżenie badanych właściwości mechanicznych, które wyznaczano z wykorzystaniem współczesnej mechaniki pękania.
-
Theoretical and mathematical models of the torque of mechanical losses in a hydraulic rotational motor for hydrostatic drive
PublikacjaW pracy przedstawiono modele teoretyczne i matematyczne momentu strat mechanicznych występujących w silniku hydraulicznym obrotowym o stałej teoretycznej chłonności qMt silnika na obrót wału (o stałej teoretycznej objętości roboczej VMt silnika) i o zmiennej chłonności qMgv = bM qMt na obrót wału (o zmiennej geometrycznej objętości roboczej VMgv silnika). Modele mają służyć badaniom laboratoryjnym i symulacyjnym strat energetycznych...
-
Mechanical response of buried High-Density Polyethylene pipelines under normal fault motions
Publikacja -
Changes of color coordinates of biological tissue with superficial skin damage due to mechanical trauma
Publikacja -
Effect of Nano-SiO2 on the Microstructure and Mechanical Properties of Concrete under High Temperature Conditions
Publikacja -
Effect of ground tire rubber on structural, mechanical and thermal properties of flexible polyurethane foams
PublikacjaFlexible polyurethane foams were modified with two kinds of ground tire rubber, untreated and thermo-mechanically reclaimed. A reclamation process was performed in auto-thermal conditions, which reduced the cost of the process and decreased the environmental impact of devulcanization (e.g., emission of gases). The reclamation process was carried out in a continuous manner using a co-rotating twin screw extruder. The foams were...
-
Microstructure, mechanical properties, and flame retardancy of nanoclay-incorporated polyurethane flexible foam composites
PublikacjaThe present work seeks to investigate microstructure, mechanical properties, and flame retardancy of polyurethane/nanoclay flexible foam composites. In this regard, we prepared various nanocomposites with and without nanoclay and observed the resulting morphologies to correlate them with the other corresponding characteristics. The results provided support for the fact that tensile strength and compression set will increase with...
-
Structure, morphology and mechanical behaviour of novel bio-based polyurethane composites with microcrystalline cellulose
PublikacjaThe aim of this work was to obtain bio-based polyurethane composites using biocomponents such as, bio-glycol, modified natural oil-based polyol, and microcrystalline cellulose (MCC). The prepolymer method was used to prepare the bio-based polyurethane matrix. Prepolymer synthesised from 4,4’-diphenylmethane diisocyanate (MDI) and a polyol mixture containing 75% wt. commercial polyether and 25% wt. hydroxylated soybean oils (H3)...
-
Rigid polyurethane foams modified with ground tire rubber - mechanical, morphological and thermal studies
PublikacjaRigid polyurethane foams, prepared by a single step method, were modified with the two types of ground tire rubber particles, i.e. untreated and thermo-mechanically reclaimed by using a co-rotating twin screw extruder. The foaming process as well as the structure and the physical, mechanical and thermal properties of the resulting foams were investigated. The presence of ground tire rubber decreased the velocity of polymerization....
-
The Effect of Cryogenic Treatment on Microstructure and Mechanical Response of AISI D3 Tool Steel Punches
PublikacjaRecently, deep cryogenic treatment is performed to improve the mechanical responses (wear, hardness, fatigue, and thermal conductivity) of various steel components. Researchers have tried to evaluate the eco-friendly and nontoxic process to optimize the parameters. Cold-shearing punches used to manufacture various holes that undergo severe impact loading and wear in the metal forming process. This study concerns the effect of soaking...
-
Estimation of the expected effects of different surface modifications on mechanical, chemical and biological behaviour of endoprostheses
PublikacjaPrzedstawiono koncepcję nowej endoprotezy o szczególnie wysokiej odporności na zużycie i pękanie. Koncepcja zakada wytwarzanie wieloetapową obróbkę powierzchniową kompozytu metalowo-ceramicznego.
-
The structure and mechanical properties of AlMg5Si2Mn alloy after surface alloying by the use of fiber laser
Publikacja -
Chemical and Mechanical Pressure-Induced Photoluminescence Tuning via Structural Evolution and Hydrostatic Pressure
Publikacja -
Mechanical Behavior of Plastic Strips-Reinforced Expansive Soils Stabilized with Waste Marble Dust
PublikacjaExpansive soil needs to undergo treatment to be used as safe foundation soil for roads and buildings. From environmental conservation and economical point of view, the usage of agricultural and industrial wastes is the best option. In this study, the effects of utilizing plastic waste and marble waste dust on the engineering properties of expansive soils were examined. Various laboratory tests were carried out on sampled expansive...
-
Evaluation of Influence of the Addition Nanofillers on the Mechanical and Thermal Properties Terpolymers Ester-Ether-Amide
Publikacja -
Triticale extrudates – Changes of macrostructure, mechanical properties and molecular water dynamics during hydration
Publikacja -
Aqueous Mechanical Oxidation of Zn Dust: An Inventive Technique for Bulk Production of ZnO Nanorods
Publikacja -
Research and development in Department of Hydraulics and Pneumatics of the Faculty of Mechanical Engineering of Gdańsk University of Technology
PublikacjaW artykule przedstawiono aktualny stan prac badawczych prowadzonych w Katedrze Hydrauliki i Pneumatyki PG:- rozwój laboratorium badawczego,- prace nad nowym typem pomp wielotłoczkowych z rozrządem krzywkowym,- prace nad silnikami satelitowymi z kompensacją luzów osiowych,- stanowisko do badań silników zasilanych emulsją wodno-olejową,- badania zachowania układów hydraulicznych w niskiej temperaturze otoczenia.
-
The analysis of the mechanical properties of welding joints of high-strength steels for offshore and ships structures
PublikacjaW artykule przedstawiono równania korelacyjne właściwości mechanicznych złaczy spawanych stali wysokiej wytrzymałości, które umożliwiają ocenę wpływu technologii spawania tych stali.W pracy zaproponowana dwa równania. Pierwsze umożliwa wstępną ocenę spawalności obecnie produkowanych stali wysokiej wytrzymałości, natomiast równania korelacyjne pozwalają obliczyć maksymalną twardość strefy wpływu ciepła materiału.
-
The Influence of Nanometals, Dispersed in the Electrophoretic Nanohydroxyapatite Coatings on the Ti13Zr13Nb Alloy, on Their Morphology and Mechanical Properties
PublikacjaIn this work, nanohydroxyapatite coatings with nanosilver and nanocopper have been fabricated and studied. The presented results concern coatings with a chemical composition that has never been proposed before. The present research aims to characterize the effects of nanosilver and nanocopper, dispersed in nanohydroxyapatite coatings and deposited on a new, non-toxic Ti13Zr13Nb alloy, on the physical and mechanical properties of...
-
Insights into the Thermo-Mechanical Treatment of Brewers’ Spent Grain as a Potential Filler for Polymer Composites
PublikacjaThis paper investigated the impact of twin-screw extrusion parameters on the properties of brewers’ spent grain. The chemical structure, antioxidant activity, particle size, and color properties, as well as the emission of volatile organic compounds during extrusion, were investigated. The main compounds detected in the air during modifications were terpenes and terpenoids, such as α-pinene, camphene, 3-carene, limonene, or terpinene....
-
Ultimate strength of stiffened plates subjected to compressive load and spatially distributed mechanical properties
PublikacjaThe present study deals with the ultimate strength of stiffened plates subjected to spatially distributed mechanical properties and compressive load. Normally, mean values of mechanical properties based on tensile tests are used to validate the numerical assessment with experimental results. However, mechanical properties may vary within a single specimen. To investigate the impact of that, random fields of yield stress and Young...
-
Mechanical Behavior of Bi-Layer and Dispersion Coatings Composed of Several Nanostructures on Ti13Nb13Zr Alloy
PublikacjaTitanium implants are commonly used because of several advantages, but their surface modification is necessary to enhance bioactivity. Recently, their surface coatings were developed to induce local antibacterial properties. The aim of this research was to investigate and compare me-chanical properties of three coatings: multi-wall carbon nanotubes (MWCNTs), bi-layer composed of an inner MWCNTs layer and an outer TiO2 layer, and...
-
Mechanical and physical assessment of epoxy, mineral, solvent-based, and water-soluble coating materials
PublikacjaThis paper assesses the behavior of mineral, epoxy (EP), solvent, and water-soluble coatings when exposed to salt and regular water for 28 days. Also, it evaluates the pull-off adhesion strength of the same coating materials applied to concrete slabs saturated with oil and water and dried with two different processes: air-dried for 28 days and air-dried for 14 days plus 14 days in the oven at 70 °C. Properties such as carbonation,...
-
Experimental study on the effect of selected sterilization methods on mechanical properties of polylactide FFF specimens
PublikacjaPurpose: Biodegradable polymers are widely used in personalized medical devices or scaffolds for tissue engineering. The manufacturing process should be finished with sterilization procedure. However, it is not clear how the different sterilization methods have an impact on the mechanical strength of the three-dimensional (3D)-printed parts, such as bone models or personalized mechanical devices. This paper aims to present the...
-
Glass-ceramic joining of Fe22Cr porous alloy to Crofer22APU: interfacial issues and mechanical properties
PublikacjaThis work deals with the joining of porous Fe22Cr ferritic stainless steel to a dense Crofer22APU plate by using a silica-based, Ba-containing glass-ceramic. The chemical and interfacial stability and the mechanical properties of the joints were evaluated before and after thermal ageing at 700 ◦C for 500hrs. The sintering behaviour of the glass was assessed by using heating stage microscopy (HSM) to study the influence of a porous...
-
Mechanical Behavior of Plastic Strips-Reinforced Expansive Soils Stabilized with Waste Marble Dust
PublikacjaExpansive soil needs to undergo treatment to be used as safe foundation soil for roads and buildings. From an environmental conservation and economical point of view, the usage of agricultural and industrial wastes is the best option. In this study, the effects of utilizing plastic waste and marble waste dust on the engineering properties of expansive soils were examined. Various laboratory tests were carried out on sampled expansive...
-
Mechanical Behavior of Bi-Layer and Dispersion Coatings Composed of Several Nanostructures on Ti Substrate
PublikacjaThree coatings suitable for biomedical applications, including the dispersion coating composed of multi-wall carbon nanotubes (MWCNTs), MWCNTs/TiO2 bi-layer coating, and MWCNTs-Cu dispersion coating, were fabricated by electrophoretic deposition (EPD) on Ti Grade II substrate. Optical microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and nanoindentation were applied to study topography, chemical, and...
-
Influence of Water-Induced Degradation of Polytetrafluoroethylene (PTFE)-Coated Woven Fabrics Mechanical Properties
PublikacjaThe impact of water-induced degradation on the mechanical properties of the chosen two PTFE-coated, glass threads woven fabrics is investigated in this paper. The paper begins with a survey of literature concerning the investigation and determination of coated woven fabric properties. The authors carried out the uniaxial tensile tests with an application of flat and curved grips to establish the proper values of the ultimate tensile...
-
Biopolymers based paper coating with promoted grease resistivity, bio-degradable and mechanical properties
Publikacja -
Characterization of Mechanical and Bactericidal Properties of Cement Mortars Containing Waste Glass Aggregate and Nanomaterials
Publikacja