wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: forced vibrations, inertial exciters, multibody dynamics, numerical analysis
-
Research of leakage magnetic field in deenergized transformer
PublikacjaThe article deals with the issue of the numerical analysis of the magnetic field occurring around the transformer after it has been powered down. The main goal of this analysis was to examine if it is possible to identify the residual fluxes in the transformer legs based on this fields’ measurements. It was also intended to determine the type and the location of magnetic sensors. Numerical analysis of the magnetic field was performed....
-
An Analysis of Elliptical-Rectangular Multipatch Structure on Dielectric-Coated Confocal and Nonconfocal Elliptic Cylinders
PublikacjaA rigorous analysis of the resonance frequency problem of an elliptical-rectangular microstrip structure mounted on dielectric-coated elliptic conducting cylinder, with electrically small radius, is investigated in this paper. A full-wave analysis and a moment-method calculation are employed. The analysis is carried out considering the expansion of the field as a series of Mathieu functions. The complex resonance frequencies of...
-
Design and investigations of the ethanol microturbine
PublikacjaThe paper presents the results of the design analysis and experimental investigations of the microturbine set consisting of the microturbine with partial admission and permanent magnet generator. The microturbine was designed for operation with the vapour of ethanol as a working fluid. Microturbine unit was tested for different parameters of the working fluid and varying the electrical load. The examples and the comparison between...
-
Assessment of tensile forces in Sopot Forest Opera membrane by in situ measurements and iterative numerical strategy for inverse problem
PublikacjaAssessment of tensile forces in newly build Sopot Forest Opera roofing membrane is presented. The procedure is based on in situ measurements and solution of the inverse problem by an iterative procedure. The goal of the analysis is to determine whether the stress state of the membrane is consistent with the design assumptions. The paper contains the description of measurements, used instruments, applied loadings, numerical investiga-tions...
-
Curb-to-Barrier Face Distance Variation an a TB51 Bridge Barrier Crash Test Simulation
PublikacjaThis paper addresses the problem of road safety regarding barrier placement as relative to the curb. A short summary of existing regulations is presented. Numerical simulations using the explicit finite element system Ls- Dyna are shown. In the analysis, variable distance between the barrier and the curb is assumed. The obtained result reveals that the distance has little impact on the working width of the barrier.
-
Stress analysis of the bridge hangers in terms of the fatigue verification
PublikacjaThe paper presents the results of numerical stress analysis of the bridge rod hangers. Two types of hangers were taken into account, i.e. the bolted hanger and the welded hanger. A detailed FEM shell models of the connection area between the hanger and the bridge span have been developed. Local stress concentration effects have been investigated in terms of fatigue verification.
-
NUMERICAL MODELLING AND EXPERIMENTATION OF HISTORICAL CARPENTRY CORNER LOG JOINTS
PublikacjaThe main purpose of this research is to determine the stress distributions on the contact surfaces between the logs of the historical carpentry corner joints. The additional purpose is to compare the stress distribution for four different boundary conditions in the case of dry and wet pine wood. The paper presents the results of numerical analysis of the shortcorner dovetail connection and the saddle notch corner joint, which are...
-
Tests of bond between concrete and steel bars – literature background and program of own research
PublikacjaThis article deals with the issue of the bond between concrete and reinforcement. The bond is crucial for reinforced concrete elements because it is possible to transfer forces (stresses) from concrete to the reinforcement. Basic information related to the cooperation of concrete and rebars was recalled in the article. Selected issues concerning theoretical and numerical analysis as well as experiments of the bond phenomenon were...
-
Estimation of the steam condensation flow via CFD methods
PublikacjaThe results of numerical simulations to predict the performance of different steam models have been presented. All of the considered models of steam condensation have been validated on the base of benchmark experiment employing expansion in nozzle and next on the low pressure part of the steam turbine stage. For numerical analysis three models have been finally used – the ideal steam model without condensation, an equilibrium steam...
-
Analysis of EN 1993-1-6 guidelines about determining amplitudes of equivalent imperfections of steel cylindrical shells subjected to uniform external pressure
PublikacjaCivil engineering structures should be designed with reference to relevant standards. One of them is a Eurocode 3 standard EN 1993-1-6:2007: Design of steel structures Part 1-6: Strength and Stability of Shell Structures. According to this standard, the value of buckling load can be determined using different approaches: classical hand calculations (stress design) and geometrical and material non-linear analysis of an imperfect...
-
INVESTIGATIONS OF THE LABORATORY FARYMANN DIESEL ENGINE D10 TYPE BY MEANS OF A LANGMUIR PROBE
PublikacjaA precise determination of the crankshaft angular position, at which fuel ignition occurs in the SI engine, enables credible diagnosis of the technical state of its working space as well as of the fuel feed system. An observation of the Langmuir probe signal provides entirely new possibilities for engine diagnostics. The probe is introduced into the working space of a cylinder through its indicator valve. This paper presents the...
-
A procedure for elastoplastic hardening function identification.
PublikacjaThe inverse analysis method for identifying a nonlinear hardening function,which governs a plastic yielding of soil and rock materials in the framework of elastoplastic theory is presented. A concept of two stage finite element based on spatial discretization of computational space and hardening function space is introduced. The proposed inverse analysis can be classified as the output least squares method. The Levenberg Marquard...
-
Dynamic inequalities and equations of Volterra type on time scales
PublikacjaPraca dotyczy całkowo-różniczkowych równań dynamicznych typu Volterry z warunkami początkowymi. Stosując twierdzenie Banacha o punkcie stałym pokazano istnienie jedynego rozwiązania liniowego równania dynamicznego. Stosując metodę iteracji monotonicznych pokazano istnienie rozwiązań ekstremalnych dla problemów nieliniowych. Badano też nierówności dynamiczne. Praca zawiera również uwagi dotyczące zagadnień różniczkowych i różnicowych.
-
Positive solutions to second order four-point impulsive problems with deviating arguments
PublikacjaStosując tw. Leggetta-Williamsa, podano warunki dostateczne na istnienie dodatnich rozwiązań dla czteropunktowych problemów brzegowych dla równań różniczkowych rzędu drugiego z odchylonymi argumentami. Dyskutowane były problemy gdy argument odchylony był typu opóźnionego lub wyprzedzonego.
-
Positive solutions to boundary value problems for impulsive second-order differential equations
PublikacjaIn this paper, we discuss four-point boundary value problems for impulsive second-order differential equations. We apply the Krasnoselskii's fixed point theorem to obtain sufficient conditions under which the impulsive second-order differential equations have positive solutions. An example is added to illustrate theoretical results.
-
Boundary value problems for dynamic equations of Volterra type on time scales
PublikacjaPraca dotyczy równań i nierówności dla problemów dynamicznych typu Volterry. Podano warunki dostateczne na istnienie ekstremalnych rozwiązań w obszarze ograniczonym przez dolne i górne rozwiązania. Praca zawiera również pewne uwagi dla konkretnych zagadnień różniczkowych i dyskretnych.
-
On integro-differential equations with delayed arguments
PublikacjaPraca dotyczy problemów różniczkowo-całkowych z warunkami początkowymi oraz brzegowymi typu okresowego. Podano warunki na istnienie i jednoznaczność rozwiązania. Badania dotyczyły również nierówności różniczkowo-całkowych z argumentami typu opóżnionego. Podano przykłady, które mogą mieć zastosowanie w problemach inżynierskich.
-
Vibrational excitation of acetylene by positron impact
PublikacjaVibrationally inelastic quantum calculations are carried out at low collision energies for the scattering of a beam of positrons off acetylene gaseous molecules. The normal mode analysis is assumed to be valid and the relative fluxes into the C–C and C–H symmetric vibrational modes are computed within a Body-Fixed (BF) formulation of the dynamics by solving the relevant vibrational Coupled Channels (VCC) equations. The clear dominance...
-
Self-Optimizing Adaptive Vibration Controller
PublikacjaThis paper presents a new approach to rejection of sinusoidal disturbances acting at the output of a discrete-time linear stable plant with unknown dynamics. It is assumed that the frequency of the sinusoidal disturbance is known, and that the output signal is contaminated with wideband measurement noise. The proposed controller, called SONIC (self-optimizing narrowband interference canceller), combines the coefficient fixing technique,...
-
Tunable Dielectric Switching of (Quinuclidinium)[MnCl4] Hybrid Compounds
PublikacjaInorganic−organic hybrid QMnCl (Q = quinuclidinium) crystals were synthesized and characterized. The X-ray and variable-temperature IR/Raman analysis demonstrate that the crystals undergo a reversible structural phase transition, which originates from an order−disorder process and is related to the dynamics of the organic Q cation. Dielectric function measurements disclose a switchability between low (“OFF”) and high (“ON”) dielectric...
-
Database of the convergence analysis results of the nonstandard approximation of the generalized Burgers–Huxley equation for the solution bounded within [0,1].
Dane BadawczeThe presented dataset is a result of the convergence analysis of the Mickens-type, nonlinear, finite-difference discretization of a generalized Burgers–Huxley partial differential equation.
-
Database of the convergence analysis results of the nonstandard approximation of the generalized Burgers–Huxley equation for the solution bounded within [0, γ^(1/p)].
Dane BadawczePresented dataset is a result of the convergence analysis of the Mickens-type, nonlinear, finite-difference discretization of a generalized Burgers–Huxley partial differential equation. The generalized Burgers–Huxley equation is a diffusive partial differential equation with nonlinear advection and diffusion. The boundary problem for this equation possesses...
-
Impacts in case of triple unilaterally constrained system
PublikacjaThe this paper focus on the behaviour of a “rigid” body biting into another “rigid” body, with some nonzero relative velocity. In the presently considered case, the introduced collision appears between a selected element of a multibody structure and its reference body being interpreted as the motionless ground. Instead of the classic case, described in a number of dissertations, where a single impacting contact is considered, three...
-
Modelowanie dynamiki odbieraka prądu pojazdu kolejowego do celów diagnostycznych
PublikacjaNiewłaściwa współpraca odbieraka prądu i sieci trakcyjnej, w trudnych warunkach lokalnych, może prowadzić do uszkodzenia sieci trakcyjnej i pantografu. W ramach rozwoju metod monitoringu i diagnostyki dla tych podsystemów, tworzone są nowe i dokładniejsze narzędzia symulacyjne, których zakres obejmuje modelowanie zarówno napowietrznej sieci trakcyjnej i pantografu, a także ich dynamicznego oddziaływania. Głównym celem jest dokładniejsza...
-
Resonant Frequencies in the Open Microstrip Structures Placed on Curved Surfaces
PublikacjaThe paper presents the research on open microstrip structures placed on curved surfaces such as cylindrical, elliptical or spherical. The numerical analysis of investigated structures is based on expansion of electric and magnetic fields into suitable function series. Utilizing the continuity conditions the boundary problem is formulated which is solved with the use of method of moments. The investigated structures find application...
-
Online Volatile Compound Emissions Analysis Using a Microchamber/Thermal Extractor Coupled to Proton Transfer Reaction-Mass Spectrometry
PublikacjaIndoor air is a complex and dynamic mixture comprising manifold volatile organic compounds (VOCs) that may cause physiological and/or psychological discomfort, depending on the nature of exposure. This technical note presents a novel approach to analyze VOC emissions by coupling a microchamber/thermal extractor (μ-CTE) system to a proton transfer reaction-mass spectrometer (PTR-MS). This configuration provides an alternative to...
-
Sektor usług wiedzochłonnych oraz jego dynamika i struktura zatrudnienia w krajach Unii Europejskiej
PublikacjaNiniejszy artykuł dotyczy sektora usług wiedzochłonnych oraz jego dynamiki i struktury zatrudnienia. W części teoretycznej opracowania przedstawiono zagadnienia definicyjne oraz klasyfikacyjne związane z sektorem usług wiedzochłonnych, a także omówiono kwestie wiedzochłonności tego sektora. W części badawczej zaprezentowano analizę dynamiki i struktury zatrudnienia w sektorach usług wiedzochłonnych krajów należących do Unii Europejskiej....
-
Experimental investigation of joint with positive eccentricity in CFS truss
PublikacjaDue to technological restrictions, in the case of trusses made of CFS open cross-sections, positive eccentricities in the truss joints have become very frequent. Therefore studies concerning the load-bearing capacity of truss joints with positive eccentricity were undertaken. It was assumed that the resistance of cold-formed steel (CFS) open cross-section truss joints located on compression chords and with positive eccentricity...
-
Effect of solar radiation on current-carrying capacity of PVC-insulated power cables – the numerical point of view
PublikacjaPower cables are usually buried in the soil, which results in their relatively high current-carrying capacity. However, there are cases in which the starting/final section of a cable line runs along a pole of an overhead power line. Power cables can be directly exposed to solar radiation then, and this negatively influences their current-carrying capacity as well as estimated life of the cables’ insulation. An analysis of thermal...
-
Modular power converter with superconducting magnetic energy storage for electric power distribution system — Analysis and simulation
PublikacjaThis paper describes selected issues concerning realization of energy storage system (ESS) designed to operate in power distribution system. This paper presents a modular approach of 300 kVA power converter operating with superconducting magnetic energy storage (SMES), which gives high dynamics together with high power and suitable capability for instantaneous energy storage. Analysis and simulation studies of selected power converter...
-
Badania i analizy kolejowych konstrukcji odciążających typu mostowego
PublikacjaW pracy przedstawiono i omówiono wybrane modele obliczeniowe, wyniki analiz teoretycznych oraz badań trzech typów kolejowych konstrukcji odciążających typu mostowego. Zaprezentowano modele obliczeniowe oraz metodykę badań in situ tego typu konbstrukcji. Przedstawiono wnioski dotyczące zaawansowanych metod obliczeniowych rozszerzonych badań in situ w celu diagnozowania rzeczywistej pracy obiektów mostowych.
-
The use of a two-phase Monte Carlo material model to reflect the dispersion of asphalt concrete fracture parameters
PublikacjaThe work covers comprehensive laboratory tests of semi-circular bending (SCB) of asphalt concrete samples. The results of two test series, including four and 32 SCB specimens, indicate a substantial scatter of force–deflection (F-d) histories. The numerical analysis is aimed to reflect the maximum breaking load and fracture energy of the samples, pointing out their random character. The original simulation-based fictitious Monte...
-
THE METHOD OF MEASURING THE MEMBRANE COVER GEOMETRY USING LASER SCANNING AND SYNCHRONOUS PHOTOGRAMMETRY
PublikacjaThe authors present the experience and results of field studies carried out at the technical acceptance of Forest Opera (name in Polish: Opera Leśna) in Sopot (Poland). An unusual design of covering made in the form of “Sheerfill I” technical fabric membrane required spanned in the form of sails, required the use of terrestrial laser scanning. Such approach allowed for the fast and accurate record of the surface of individual panels...
-
Conley-Morse graphs for a two-dimensional discrete neuron model (low resolution)
Dane BadawczeThis dataset contains selected results of rigorous numerical computations conducted in the framework of the research described in the paper “Topological-numerical analysis of a two-dimensional discrete neuron model” by Paweł Pilarczyk, Justyna Signerska-Rynkowska and Grzegorz Graff. A preprint of this paper is available at https://doi.org/10.48550/arXiv.2209.03443.
-
Conley-Morse graphs for a two-dimensional discrete neuron model (limited range)
Dane BadawczeThis dataset contains selected results of rigorous numerical computations conducted in the framework of the research described in the paper “Topological-numerical analysis of a two-dimensional discrete neuron model” by Paweł Pilarczyk, Justyna Signerska-Rynkowska and Grzegorz Graff. A preprint of this paper is available at https://doi.org/10.48550/arXiv.2209.03443.
-
Conley-Morse graphs for a two-dimensional discrete neuron model (full range)
Dane BadawczeThis dataset contains selected results of rigorous numerical computations conducted in the framework of the research described in the paper “Topological-numerical analysis of a two-dimensional discrete neuron model” by Paweł Pilarczyk, Justyna Signerska-Rynkowska and Grzegorz Graff. A preprint of this paper is available at https://doi.org/10.48550/arXiv.2209.03443.
-
Arsalan Muhammad Soomar Doctoral Student
OsobyHi, I'm Arsalan Muhammad Soomar, an Electrical Engineer. I received my Master's and Bachelor's Degree in the field of Electrical Engineering from Mehran University of Engineering and Technology, Jamshoro, Sindh, Pakistan. Currently enrolled as a Doctoral student at the Gdansk University of Technology, Gdansk, Poland. Also worked in Yellowlite. INC, Ohio as a Solar Design Engineer. HEADLINE Currently Enrolled as a Doctoral...
-
Identification of Parameters Influencing the Accuracy of the Solution of the Nonlinear Muskingum Equation
PublikacjaTwo nonlinear versions of the Muskingum equation are considered. The difference between both equations relates to the exponent parameter. In the first version, commonly used in hydrology, this parameter is considered as free, while in the second version, it takes a value resulting from the kinematic wave theory. Consequently, the first version of the equation is dimensionally inconsistent, whereas the proposed second one is consistent. It...
-
Rozprzestrzenianie się w podtorzu skutków katastrof kolejowych z udziałem materiałów niebezpiecznych
PublikacjaDuża część przewozów materiałów niebezpiecznych prowadzona jest koleją. W związku z tym bezpieczeństwo tych przewozów nabiera coraz większego znaczenia. Każda katastrofa z udziałem materiałów niebezpiecznych ma negatywny wpływ na uczestników tego zdarzenia oraz na otaczające środowisko, bowiem jej zasięg na ogół nie jest lokalny. Z tego wynika, że w przypadku zaistnienia katastrofy należy minimalizować jej skutki oraz w dalszych...
-
Parametric analysis of Istanbul's Ring Road viaduct for three levels of seismic load
PublikacjaThe paper presents a numerical analysis of the Istanbul's ring road viaduct that is currently under construction within the Northern Marmara Highway project. The structure, due to its location on seismic prone areas is exposed to seismic loads of different magnitude and different return periods. The study is fo-cused on concrete bridge supports that are design to work in nonlinear range. The study, conducted in SOFISTIK environment,...
-
Analysis of sloping brace stiffness influence on stability and load bearing capacity of a truss
PublikacjaThe paper is focused on the numerical study of stability and load bearing capacity of a truss with side elastic braces. The structure is made in reality. The rotational and sliding brace stiffnesses were taken into account. Linear buckling analysis and non-linear static analysis with geometric and material nonlinearity were performed for the beam and shell model of the truss with respect to the angle of sloping braces. As a result...
-
Lamb wave propagation in a single lap adhesive joint
PublikacjaThe aim of the paper is the analysis of Lamb wave propagation in adhesive joints. The research was performed on a single lap adhesive joint of two steel plates. Two types of joints, namely an intact and with defect were considered. In experimental investigations the condition assessment of the joint was performed with the use of antisymmetric Lamb waves excited by a plate piezo actuators and measured by a laser vibrometer. Numeri-cal...
-
Stability of an imperfect truss loaded by wind
PublikacjaThe present paper is devoted to the numerical research of stability of a truss loaded by wind and stiffened by elastic supports located at the top chord. The lateral braces or lateral and torsional braces were taken into account. In this paper, the linear buckling analysis re- sults for the beam and shell model were presented. Two different shapes of initial geometric imperfections were considered in the non-linear static analysis...
-
Concept of an Innovative System for Dimensioning and Predicting Changes in the Coastal Zone Topography Using UAVs and USVs (4DBatMap System)
PublikacjaThis publication is aimed at developing a concept of an innovative system for dimensioning and predicting changes in the coastal zone topography using Unmanned Aerial Vehicles (UAVs) and Unmanned Surface Vehicles (USVs). The 4DBatMap system will consist of four components: 1. Measurement data acquisition module. Bathymetric and photogrammetric measurements will be carried out with a specific frequency in the coastal zone using...
-
BADANIA ODBIOROWE ŁUKOWEJ KŁADKI DLA PIESZYCH 10T NAD DROGĄ S8 W WARSZAWIE
PublikacjaThe paper presents in situ load testing of the newly build footbridge over S8 expressway in Warsaw. The most characteristic thing for the structure is a shape of arch girders, which correspond with adjacent half-tunnel acoustic baffles. The paper consists of description of the structure, results of the in-situ static and dynamic load testing, results of the numerical simulations, comparative analysis and final conclusions on the...
-
Automated microwave planar filter design with generalized Chebyshev characteristics.
PublikacjaIn this paper a technique of automatization of design of microwave filters with generalized Chebyshev characteristics is presented. A full wave electromagnetic simulator linked with the Matlab computing environment is used to ensure a rigorous numerical analysis while at the same time allowing automatization. To decrease time of optimization and overall design process, the Cauchy interpolation technique was used. An automated design...
-
Resonant Frequencies in Microstrip Structure with Omega Medium Substrate
PublikacjaThe paper presents the research on a rectangular microstrip structure with multilayer substrate containing dielectric and omega medium layers. The effect of pseudochiral medium layer location in the substrate and its thickness on the resonant frequency of the rectangular microstrip structure is investigated. The numerical analysis of investigated structures is based on expansion of electric and magnetic fields. Utilizing the continuity...
-
Modal FEM Analysis of Ferrite Resonant Structures
PublikacjaThe finite-element method (FEM) is applied for modal analysis of ferrite-loaded spherical resonators. To improve the efficiency of the numerical calculations, the body-of-revolution (BOR) technique is utilized. Due to the frequency-dependent ferrite permeability, FEM leads to a nonlinear eigenvalue problem that is challenging to solve. To this end, Beyn’s method is proposed. The effectiveness of the proposed approach is confirmed...
-
Research on protection mechanisms of Resilient Packet Ring Network.
PublikacjaPaper describes iSteering - a new method to control traffic in case of RPR network failure. There's comparison of packet wrapping, steering and our proposed method iSteering, which can be used in case of transmitter/receiver or fiber failure. Numerical analysis for even and random traffic flow has been made in order to compare packet wrapping, steering and iSteering. The results of all the tests are included.
-
Four Degree-of-Freedom Hydrodynamic Maneuvering Model of a Small Azipod-Actuated Ship With Application to Onboard Decision Support Systems
PublikacjaThe main contribution of this paper is a numerical ship motion model of NTNU’s research vessel Gunnerus, capturing the surge, sway, roll, and yaw dynamics when sailing in uniform and steady currents. The model utilizes a crossflow drag formulation for the transverse viscous loads, and it includes a nonlinear formulation for the propulsion and steering loads provided by two azipod thrusters. A wide range of experimental data obtained...