Wyszukiwarka
Filtry
wszystkich: 1057
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: predicting the breakout force
-
Dynamics of fault arc traveling along busbars in high voltage switchboards = Dynamika łuku zwarciowego przemieszczającego się wzdłuż szyn rozdziel-nic wysokiego napięcia
PublikacjaThe paper presents the results of magnetic induction and electrodynamic force calculations acting on arc column during short-circuit in medium voltage air-insulated bus-bars. The gap between the bars was 120 mm and the prospective short-circuit currents ranged from 4 kA to 8 kA. The paper also shows the measurement results of average velocity fault arc depending on currents arc diameter and arc current was established and described....
-
Acoustic heating produced in the thermoviscous flow of a bingham plastic
PublikacjaThis study is devoted to the instantaneous acoustic heating of a Bingham plastic. The model of the Bingham plastic's viscous stress tensor includes the yield stress along with the shear viscosity, which differentiates a Bingham plastic from a viscous Newtonian fluid. A special linear combination of the conservation equations in differential form makes it possible to reduce all acoustic terms in the linear part of of the final equation...
-
Influence of compaction effectiveness on interlayer bonding of asphalt layers
PublikacjaThe paper presents the results of research on the interlayer bonding of asphalt layers compacted in the laboratory and in the field. To measure the interlayer bonding at a temperature of 20°C the Leutner test apparatus was used and load was applied at a rate of 50 mm/minute. Three types of interlayer interfaces were tested: no tack coat and tack coats made of two types of the pure bitumen emulsions. Four compaction techniques were...
-
THE IDENTIFICATION OF TOXIC COMPOUND EMISSION SENSITIVITY AS A DIAGNOSTIC PARAMETER DURING DYNAMIC PROCESSES OF THE MARINE ENGINE
PublikacjaChanging some parameters of the engine structure alters the emission of harmful components in the exhaust gas. This applies in particular to the damage of charge exchange system as well as fuel system and engine supercharger. These changes are much greater during the dynamic states and their accompanying transitional processes. The different sensitivity of diagnostic parameters to the same force, coming from the engine structure,...
-
Localized impedance measurements of AA2024 and AA2024-T3 performed by means of AFM in contact mode
PublikacjaPurpose: The purpose of this paper is to present the results of an atomic force microscopy (AFM) based approach to local impedance spectroscopy (LIS) measurement performed on AA2024 and AA2024-T3 aluminium alloys. Design/methodology/approach: AFM-LIS measurements were performed ex-situ without the electrolyte environment, so in fact the electrical not electrochemical impedance was obtained. Findings: Relative local impedance values...
-
Numerical Analysis of a Steel Frame Building with Soft-storey Failure under Ground Motion Excitation
PublikacjaThe aim of this paper is to show the results of a numerical analysis focused on the behaviour of multi-storey steel frame building that suffers from a soft-storey failure under ground motion excitation. A numerical model of the structure was created in FEM computer software and was exposed to an impact that would have been generated after a soft-storey failure due to falling of the upper floors. During the analysis, the whole structure...
-
Acoustic heating produced in the thermoviscous flow of a Bingham plastic
PublikacjaThis study is devoted to the instantaneous acoustic heating of a Bingham plastic. The model of the Bingham plastic's viscous stress tensor includes the yield stress along with the shear viscosity, which differentiates a Bingham plastic from a viscous Newtonian fluid. A special linear combination of the conservation equations in differential form makes it possible to reduce all acoustic terms in the linear part of of the final equation...
-
Influence of Two-Stage Anodization on Properties of the Oxide Coatings on the Ti–13Nb–13Zr Alloy
PublikacjaThe increasing demand for titanium and its alloys used for implants results in need of such innovative surface treatment that may jointly increase corrosion resistance and biocompatibility, and demonstrate antibacterial protection at no cytotoxicity. The purpose of this research was to characterize the effect of two-stage anodization, performed for 30 min in phosphoric acid, at the presence of hydrofluoric acid in the second stage....
-
Application of Shape Memory Alloys in Pipeline Couplings for Shipbuilding
PublikacjaThe aim of the study is to analyse shape memory alloy (SMA) pipeline joints in limited space applications for all kinds of ships. Generally, the space available in various areas on ships is strictly limited and service works usually meet many obstacles. If we consider a pipeline, the flange joints always require a larger free space around the pipe than the pipe alone. A simultaneous problem can occur with the propeller shaft line...
-
Open Innovation Competence for a Future-Proof Workforce: A Comparative Study from Four European Universities
PublikacjaDigital transformation is a key driving force of open innovation to capture and transfer knowledge inside and outside of a company’s bounds. New challenges in organizing multiple knowledge flows imply the need for increased competences related to this paradigm of future employees. In this article, we organize and aggregate the competencies required for open innovation collaboration and develop a competence profile that organizes...
-
Numerical and experimental study on effect of boundary conditions during testing of stiffened plates subjected to compressive loads
PublikacjaThis study analyses the effect of boundary conditions during testing on the structural behaviour stiffened plates with different thicknesses subjected to compressive loads. The goal of the compressive tests is to analyse the ultimate strength of a stiffened plate. During the test, relevant physical quantities are measured and investigated. The supporting structure's behaviour is investigated by analysing the force-displacements...
-
Use of Bi-Temporal ALS Point Clouds for Tree Removal Detection on Private Property in Racibórz, Poland
PublikacjaTrees growing on private property have become an essential part of urban green policies. In many places, restrictions are imposed on tree removal on private property. However, monitoring compliance of these regulations appears difficult due to a lack of reference data and public administration capacity. We assessed the impact of the temporary suspension of mandatory permits on tree removal, which was in force in 2017 in Poland,...
-
Optimisation and field assessment of poroelastic wearing course bond quality
PublikacjaCompared to typical asphalt mixtures, poroelastic mixtures are characterised by high porosity and high flexibility, which are desirable for traffic noise reduction. However, the same properties increase the risk of debonding from the lower layer, which is a significant source of premature damage. The study investigates which of the factors – tack coat agent, type and texture of the lower layer – have the greatest impact on interlayer...
-
Miasta na prawach powiatu z rozwiniętym przemysłem jako lokalne ośrodki rozwoju na obszarach peryferyjnych polskich regionów
PublikacjaMost of the growth factors is situated in big cities, especially in metropolitan areas. Questions arise: 1) Whether and what development factors are in the peripheral areas of voivodeships (i.e. outside the functional areas of their capitals)? 2) Can the industry be the driving force of the development of these areas? These questions are related to the discussion on the reindustrialisation of the European Union and the role of...
-
Estimation of fracture toughness and shear yield stress of orthotropic materials in cutting with rotating tools
PublikacjaThe cutting force is an energetic effect of splitting material, and might be considered from a point of view of modern fracture mechanics. Forecasting of the shear plane angle in cutting broaden possibilities for modelling of the cutting process even for thin uncut chips. Such mathematical model has been developed here for description of the orthotropic materials’ cutting on the base of fracture theory, and includes work of separation...
-
Students receiving scholarships in 1990-2011
Dane BadawczeSince 2005, the financial support system for students has been operating on the basis of on the Act of 27 July 2005, the Law on Higher Education (Journal of Laws No. 164, item 1365), as amended, and detailed regulations for determining the amount, awarding and payment of financial assistance benefits for students determined by rectors in consultation...
-
Cerclage cable augmentation does not increase stability of the fixation of intertrochanteric fractures. A biomechanical study
PublikacjaBackground: Intertrochanteric fractures with a posteromedial intermediate fragment are unstable because of the loss of medial support. Additional fixation with a cerclage is used in subtrochanteric fractures, but not in intertrochanteric fractures. The aim of this biomechanical study is to evaluate whether cerclage fixation improves stability of intertrochanteric fractures. Hypothesis: Our hypothesis is that the cerclage fixation...
-
Electron attachment to representative cations composing ionic liquids
PublikacjaUsing ab initio electronic structure methods with flexible atomic orbital basis sets, we investigated the electronic structure and stability of reduction products of selected representative cations (C+) constituting ionic liquids. We found that an electron attachment to such cations leads to the neutral radicals, whereas a subsequent attachment of another (i.e., excess) electron leads to adiabatically stable anions only in two...
-
Application of a hybrid mechanistic/machine learning model for prediction of nitrous oxide (N2O) production in a nitrifying sequencing batch reactor
PublikacjaNitrous oxide (N2O) is a key parameter for evaluating the greenhouse gas emissions from wastewater treatment plants. In this study, a new method for predicting liquid N2O production during nitrification was developed based on a mechanistic model and machine learning (ML) algorithm. The mechanistic model was first used for simulation of two 15-day experimental trials in a nitrifying sequencing batch reactor. Then, model predictions...
-
Electrochemistry/mass spectrometry (EC/MS) for fast generation and identification of novel reactive metabolites of two unsymmetrical bisacridines with anticancer activity.
PublikacjaThe development of a new drug requires knowledge about its metabolic fate in a living organism, regarding the comprehensive assessment of both drug therapeutic activity and toxicity profiles. Electrochemistry (EC) coupled with mass spectrometry (MS) is an efficient tool for predicting the phase I metabolism of redox-sensitive drugs. In particular, EC/MS represents a clear advantage for the generation of reactive drug transformation...
-
Intelligent Knowledge-Base Model for IT Support Organization Evolution
PublikacjaThe goal of the paper is building the knowledge-based model for predicting the state of the IT support organization. These organizations, critical for development of various business sectors, are facing the problem of their transformation. It is the result of the fundamental change in the role of the IT organizations in the current economy. The complexity of the processes, the difficulty adjusting the operations and limited ability...
-
Employing Subjective Tests and Deep Learning for Discovering the Relationship between Personality Types and Preferred Music Genres
PublikacjaThe purpose of this research is two-fold: (a) to explore the relationship between the listeners’ personality trait, i.e., extraverts and introverts and their preferred music genres, and (b) to predict the personality trait of potential listeners on the basis of a musical excerpt by employing several classification algorithms. We assume that this may help match songs according to the listener’s personality in social music networks....
-
Molecular Dynamics to Predict Cryo-EM: Capturing Transitions and Short-Lived Conformational States of Biomolecules
PublikacjaSingle-particle cryogenic electron microscopy (cryo-EM) has revolutionized the field of the structural biology, providing an access to the atomic resolution structures of large biomolecular complexes in their near-native environment. Today’s cryo-EM maps can frequently reach the atomic-level resolution, while often containing a range of resolutions, with conformationally variable regions obtained at 6 Å or worse. Low resolution...
-
Can Web Search Queries Predict Prices Change on the Real Estate Market?
PublikacjaThis study aims to explore whether the intensity of internet searches, according to the Google Trends search volume index (SVI), is a predictor of changes in real estate prices. The motivation of this study is the possibility to extend the understanding of the extra predictive power of Google search engine query volume of future housing price change (shift direction) by (i) the introduction of a research approach that combines...
-
Phototransformation of three selected pharmaceuticals, naproxen, 17α-Ethinylestradiol and tetracycline in water: Identification of photoproducts and transformation pathways
PublikacjaTransformation products (TPs) may be formed during various processes, however, it was proved that one of the main mechanisms responsible for degradation of pharmaceuticals in natural waters is photolysis. Three compounds were selected, tetracycline (TC), 17-α-ethinylestradiol (EE2) and naproxen (NAP), for degradation experiments which were performed using a xenon lamp emitting light with a spectrum closely approximating that of...
-
Współczynniki strat energetycznych w elementach napędu hydrostatycznego
PublikacjaW każdym układzie napędowym należy zastąpić obraz przepływu mocy opisany dotychczas powszechnie stosowanym wykresem Sankey’a spadku mocy zgodnego z kierunkiem przepływu mocy proponowanym przez autora wykresem wzrostu mocy w układzie przeciwnego do kierunku przepływu mocy. Należy więc opisywać straty i sprawność energetyczną a także pole pracy każdego silnika i układu napędowego jako zależne od wielkości fizycznych niezależnych...
-
Grzebowiska dla zwierząt w Polsce
PublikacjaW niniejszym artykule podjęto tematykę miejsc pochówku zwierząt. Problem został omówiony w odniesieniu do terenu Polski na tle przykładów z zagranicy. Współczesne grzebowiska dla zwierząt powstają w naszym kraju od niedawna i mimo że cmentarze dla zwierząt są u nas stosunkowo nowym zjawiskiem, to już teraz można dostrzec ich typowe cechy przestrzenne. Autorka, na co dzień zajmująca się zagadnieniami z dziedziny architektury, starała...
-
Wpływ stopowania laserowego z użyciem nanorurek węglowych stopu Ti13Nb13Zr do zastosowań biomedycznych na jego wybrane własności mechaniczne
PublikacjaDo eksperymentu użyto stopu tytanu Ti13Nb13Zr, który ze względu na swój skład chemiczny i właściwości mechaniczne stanowi materiał do zastosowań w inżynierii medycznej. Celem pracy była ocena wpływu stopowania laserowego stopu Ti13Nb13Zr z powłoką z wielościennych nanorurek węglowych na jego właściwości mechaniczne (chropowatość, nanotwardość, moduł Younga). Do wytworzenia powłoki węglowej wykorzystano metodę osadzania elektroforetycznego (EDP)....
-
Verification of punching shear outside the shear cap by the direct method
PublikacjaThe proposition of a method to verify the punching resistance for very large supports based on the EN 1992-1-1 standard is described in this paper. The present standard guidelines for the calculation of the punching resistance for large supports are also summarised. The proposed direct method is compared with other standard methods using an example taken from design practice. This method consists of a direct check of the shear...
-
Experimental and analytical analysis of punching shear in flat slabs supported on column topped with concrete head
PublikacjaAn experimental laboraatory test of the two series of slab-column elements topped with drop panels of varying sizes is described in this paper. The scope of the paper is to investigate the influence of the drop panel size and stiffness on the behaviour of the connection between the flat slab and the column topped by the concrete head. The impact of the head size and stiffness is analysed analytically and experimentally. The experimental...
-
Brownian Motion in Optical Tweezers, a Comparison between MD Simulations and Experimental Data in the Ballistic Regime
PublikacjaThe four most popular water models in molecular dynamics were studied in large-scale simulations of Brownian motion of colloidal particles in optical tweezers and then compared with experimental measurements in the same time scale. We present the most direct comparison of colloidal polystyrene particle diffusion in molecular dynamics simulations and experimental data on the same time scales in the ballistic regime. The four most...
-
Determinants of Directionality and Efficiency of the ATP Synthase Fo Motor at Atomic Resolution
PublikacjaFo subcomplex of ATP synthase is a membrane-embedded rotary motor that converts proton motive force into mechanical energy. Despite a rapid increase in the number of high-resolution structures, the mechanism of tight coupling between proton transport and motion of the rotary c-ring remains elusive. Here, using extensive all-atom free energy simulations, we show how the motor’s directionality naturally arises from the interplay...
-
Multimodal analysis of traction forces and the temperature dynamics of living cells with a diamond-embedded substrate
PublikacjaCells and tissues are constantly exposed to chemical and physical signals that regulate physiological and pathological processes. This study explores the integration of two biophysical methods: traction force microscopy (TFM) and optically detected magnetic resonance (ODMR) to concurrently assess cellular traction forces and the local relative temperature. We present a novel elastic substrate with embedded nitrogen-vacancy microdiamonds...
-
Introduction to the RSC Advances themed collection on nano and microscale modifications of biomaterials
PublikacjaThe dramatically increasing development of novel biomaterials, their manufacturing techniques, and surface modications, as well as their application in in vivo tests and clinical trials, is evident. It is interesting to note in what a relatively short time the well-known long-term implants have become medical standard: titanium dental implants started in 1965, and total hip arthroplasty (not very successful) was rst attempted...
-
Method of Forming Road Surface Replicas Using 3D Printing Technology
PublikacjaRolling resistance is a critical factor that influences vehicle energy consumption, emissions, and overall performance. It directly impacts fuel efficiency, tire longevity, and driving dynamics. Traditional rolling resistance tests are conducted on smooth steel drums, which fail to replicate real-world road surface textures, potentially skewing results. This article presents the process of designing surface replicas using 3D printing...
-
A Probe into the Corrosion Behavior of a WE43B Magnesium Alloy in a Simulated Body Fluid using Dynamic Electrochemical Impedance Spectroscopy
PublikacjaWE43B is one of the newest Mg alloys with practical application in biomedical implant technology. This work attempts to scrutinize the corrosion characteristics of WE43B alloy in a simulated body fluid (SBF) at a typical body temperature. The dynamic-electrochemical impedance spectroscopy with the capacity to track changes on surfaces in a dynamic corrosive system is used in combination with other classical techniques namely, linear...
-
Employment Specialization in the Enlarged European Union
PublikacjaThis paper presents the evolution of absolute employment specialization along the course of economic growth of 25 EU countries. We focus on the degree to which EU economies concentrate labor force in a few sectors/industries. Using disaggregated statistics classified according to NACE Rev. 1 division (71 sectors) we calculate various synthetic indices measuring the degree of diversification typical for the employment structures...
-
Solid-contact lead(II) ion-selective electrodes for potentiometric determination of lead(II) in presence of high concentrations of Na(I), Cu(II), Cd(II), Zn(II), Ca(II) and Mg(II)
PublikacjaLead and its compounds are a serious threat to the environment. Monitoring of this toxic heavy metal is a driving force for the continuous development of novel lead(II) ionophores to be applied in ion-selective electrodes. In this work a highly selective lead(II) ionophore, namely 25,26,27,28-tetrakis(piperidinylthiocarbonylmethylene)-p-tert-butylcalix[4]arene, was used in solid-contact ion-selective electrodes for determination...
-
Sawing Processes as a Way of Determining Fracture Toughness and Shear Yield Stresses of Wood
PublikacjaA new computational model, based on fracture mechanics, was used to determine cutting forces. Unlike traditional computing methods, which depend on many coefficients reflecting the machining of solid wood, the new model uses two main parameters: fracture toughness and shear yield stresses. The aim of this study was to apply this new method to determine these parameters for the tooth cutting edge principal positions and longitudinal...
-
AFM-assisted investigation of conformal coatings in electronics
PublikacjaPurpose – This paper aims to presents a new method of investigation of local properties of conformal coatings utilized in microelectronics. Design/methodology/approach – It is based on atomic force microscopy (AFM) technique supplemented with the ability of local electrical measurements, which apart from topography acquisition allows recording of local impedance spectra, impedance imaging and dc current mapping. Potentialities...
-
Analysis of abrasive particle trajectories during single-sided lapping process with driven conditioning ring
PublikacjaIn this paper new kinematics systems were studied for a single lapping process. In order to ensure the constant profile wear of the tool a standard kinematic system can be changed. Lapping is carried out by applying loose abrasive grains between two surfaces and causes a relative motion between them. The result is a finish of multi-directional lay. During process, the mechanism of surface formation are decisively affected by a...
-
Validation Process for Computational Model of Full-Scale Segment for Design of Composite Footbridge
PublikacjaExperimental tests and numerical simulations of a full-scale segment of a foot and cycle bridge made of polymer composites are presented in the paper. The analysed structure is made of sandwich panels, which consist of glass fibre reinforced polymer (GFRP) multi-layered laminate faces and a PET foam (obtained from recycling) core. The dimensions of the segment cross-section are the same as for the target footbridge; however, span...
-
Experimental and numerical investigations of ultimate strength of imperfect stiffened plates of different slenderness
PublikacjaThe objective of this study is to analyse the behaviour of compressed stiffened plates of different slenderness using experimental and numerical methods. The presented results are part of a long-term project to investigate the ultimate strength of geometrically imperfect structures subjected to different degradation phenomena, including corrosion degradation and locked cracks. Several specimens were subjected to a uniaxial compressive...
-
SMART AND RESILIENT CITIES – NEW CHALLENGES FOR POLISH CITIES IN TERMS OF 2020 BUILDING ENERGY EFFICIENCY AND CLIMATE CHANGE ACTION.
PublikacjaGlobal climate change action along with energy efficiency optimizations are becoming increasingly pressing principles in terms of moving towards sustainable development. As a member of EU and UN Poland is also obliged to follow restricted rules concerning energy efficiency of buildings which come to force in 2020. To meet new goals, innovative approaches - like moving towards smart and resilient cities -may be required. Through...
-
On the geometrically nonlinear vibration of a piezo-flexomagnetic nanotube
PublikacjaIn order to describe the behavior of thin elements used in MEMS and NEMS, it is essential to study a nonlinear free vibration of nanotubes under complicated external fields such as magnetic environment. In this regard, the magnetic force applied to the conductive nanotube with piezo-flexomagnetic elastic wall is considered. By the inclusion of Euler-Bernoulli beam and using Hamilton’s principle, the equations governing the system...
-
Incorporation of nitrogen in diamond films – A new way of tuning parameters for optical passive elements
PublikacjaThis paper investigates the impact of nitrogen incorporation in diamond films for the construction of an interferometric sensor to measure displacement. Diamond films with different nitrogen levels (0–5%) were deposited on silicon substrates by microwave plasma enhanced chemical vapor deposition. The structural characteristics of these samples are characterized using scanning electron microscopy (SEM), atomic force microscopy (AFM), confocal...
-
Influence of the femoral offset on the muscles passive resistance in total hip arthroplasty
PublikacjaBackground Soft tissue tension is treated as a crucial factor influencing the post-THA dislocation. The femoral offset is regarded as one of the major parameters responsible for the stabilization of the prosthesis. It is unclear which soft tissue is mostly affected by the offset changes. Methods A finite element model of the hip was created. The model comprised muscles, bones, a stem, the acetabular component and a liner. The muscles...
-
UNDECLARED WORK IN POLAND CHARACTERISTICS AND PREVALENCE
PublikacjaThis article aims to present the significance and prevalence of the phenomenon of undeclared work. First, we discuss the definitional issues of this phenomenon. Then, we present previous estimates on shadow economy and undeclared work in Poland, based on statistics provided by Central Statistical Office and other research entities. Our analysis covers the years 2000–2014. In the last part of the article, we use data from the Labour...
-
NON-LINE ANALYSIS OF STIFFNESS IN COMPRESSION CONDITIONS
PublikacjaThe analyzes were aimed at demonstrating the influence of parameters describing the deformation of the structure on the uncertainty of critical force, and the impact of technological imperfections on stress uncertainty in compression conditions. In a linear buckling analysis, the problem is considered only for the initial, permanent state of the stiffness matrix. In the case of demonstrating the influence of initial deformations...
-
Improvement of Thrust Bearing Calculation Considering the Convectional Heating within the Space between the Pads
PublikacjaA modern thrust bearing tool is used to estimate the behavior of tilting pad thrust bearings not only in the oil film between pad and rotating collar, but also in the space between the pads. The oil flow in the space significantly influences the oil film inlet temperature and the heating of pad and collar. For that reason, it is necessary to define an oil mixing model for the space between the pads. In the bearing tool, the solutions...