wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: PROPER GRADIENT MAP
-
Performance Evaluation of a 650V E-HEMT GaN Power Switch
PublikacjaGaN power switches have better characteristics compared to the state-of-the-art Si power transistors. These devices offer high operating temperature and current densities, fast switching and low on-resistance. However, currently only a few producers offer technology of high voltage GaN transistors. Immaturity of this technology is the reason why experimental evaluation of GaN parameters must be performed to properly exploit their...
-
The realization of ASON/GMPLS control plane
PublikacjaASON (Automatic Switched Optical Network) is a concept of optical network recommended in G.8080/Y.1304 by ITU-T. Control Plane of this network could be based on GMPLS (Generalized Multi-Protocol Label Switching) protocols like RSVP-TE, OSPF-TE, LMP. This solution is named ASON/GMPLS. In this chapter we present the control plane problems and proposes ASON/GMPLS network realization that are tested on testbed consists of three and...
-
A new approach to designing control of dissolved oxygen and aeration system in sequencing batch reactor by applied backstepping control algorithm
PublikacjaThe Wastewater Treatment Plant (WWTP) is a very complex system, due to its nonlinearity, time-variance, and multiple time scales in its dynamics among others. The most important control parameter in a WWTP is the Dissolved Oxygen (DO) concentration. The tracking problem of the DO concentration is one of the most fundamental issues in biological wastewater treatment. Proper DO concentration control is necessary to achieve adequate...
-
Concrete Compressive Strength Under Changing Environmental Conditions During Placement Processes
PublikacjaThe technological process of concrete production consists of several parts, including concrete mix design, concrete mix production, transportation of fresh concrete mix to a construction site, placement in concrete framework, and curing. Proper execution of these steps provides good quality concrete. Some factors can disturb the technological process, mainly temperature and excessive precipitation. Changing daily temperature and...
-
Neural Modelling of Steam Turbine Control Stage
PublikacjaThe paper describes possibility of steam turbine control stage neural model creation. It is of great importance because wider application of green energy causes severe conditions for control of energy generation systems operation Results of chosen steam turbine of 200 MW power measurements are applied as an example showing way of neural model creation. They serve as training and testing data of such neural model. Relatively simple...
-
COVID-19 severity forecast based on machine learning and complete blood count data
PublikacjaProper triage of COVID-19 patients is a key factor in eective case management, especially with limited and insucient resources. In this paper, we propose a machine-aided diagnostic system to predict how badly a patient with COVID-19 will develop disease. The prognosis of this type is based on the parameters of commonly used complete blood count tests, which makes it possible to obtain data from a wide range of patients.We chose...
-
COVID-19 severity forecast based on machine learning and complete blood count data
PublikacjaProper triage of COVID-19 patients is a key factor in eective case management, especially with limited and insucient resources. In this paper, we propose a machine-aided diagnostic system to predict how badly a patient with COVID-19 will develop disease. The prognosis of this type is based on the parameters of commonly used complete blood count tests, which makes it possible to obtain data from a wide range of patients.We chose...
-
A Universal Gains Selection Method for Speed Observers of Induction Machine
PublikacjaProperties of state observers depend on proper gains selection. Each method of state estimation may require the implementation of specific techniques of finding those gains. The aim of this study is to propose a universal method of automatic gains selection and perform its verification on an induction machine speed observer. The method utilizes a genetic algorithm with fitness function which is directly based on the impulse response...
-
Insights into Compatibilization of Poly(ε-caprolactone)-based Biocomposites with Diisocyanates as Modifiers of Cellulose Fillers
PublikacjaThis study aimed to analyze the impact of cellulose fillers’ modification with diisocyanates on the performance of composites based on the poly(ε-caprolactone) (PCL) matrix. Four most commonly used diisocyantes (isophorone, hexamethylene, toluene, and methylene diphenyl) were applied as modifiers of cellulose fillers (5 and 15 wt% per mass of filler). Modified fillers were introduced in the amount of 30 wt% into the PCL matrix....
-
THE CONCEPT OF MODELING OF SNOW IMPACT ON THE STRUCTURE OF THE SUSPENDED TAURON ARENA ROOF IN CRACOW
PublikacjaThe article presents studies and numerical simulations on modeling snow influence on TAURON ARENA suspended roof structure in Cracow. The scope of work includes experimental tests, functions solutions taking into account various cases of snow impact according to PN and EC, as well as numerical simulations for the sport and entertainment arena in the Czyzyny district. The FEM roof structure model developed in the SOFISITK software...
-
Smart Document-Centric Processing of Human Oriented Information Flows
PublikacjaUsually people prefer to focus on creative rather than repetitive and schematic work patterns. Still, they must spend a lot of time complying with the procedures, selecting the information they receive and repeatedly restoring the previous state of work. This paper proposes the Mobile INteractive Document architecture (MIND) - a document-centric uniform interface to provide both effective communication of content and coordination...
-
Implementing Smart Virtual Product Development (SVPD) to Support Product Manufacturing
PublikacjaThis paper illustrates the concept of providing the manufacturing knowledge during early stages of product life cycle to experts working on product development. The aim of this research is to enable a more collaborative product development environment by using Smart Virtual Product Development (SVPD) system, which is powered by Set of Experience Knowledge Structure (SOEKS) and Decisional DNA (DDNA). It enhances the industrial product...
-
Fiber-optic sensors based on microspheres with nanocoatings (Zastosowanie mikrosfer optycznych z cienkowarstwowymi pokryciami w czujnikach światłowodowych)
PublikacjaTemperature is one of the most important physical quantities. Temperature measurements are used in every field of life, especially electronics, electrical engineering, energy-related fields, including energy source and storage devices. The goal of this dissertation is to design and optimize the microsphere-based fiber-optic sensors construction for measurement of the sensor surrounding medium temperature, including selection of...
-
Biomedical engineering of polysaccharide-based tissue adhesives: Recent advances and future direction
PublikacjaTissue adhesives have been widely used for preventing wound leaks, sever bleeding, as well as for enhancing drug delivery and biosensing. However, only a few among suggested platforms cover the circumstances required for high-adhesion strength and biocompatibility, without toxicity. Antibacterial properties, controllable degradation, encapsulation capacity, detectability by image-guided procedures and affordable price are also...
-
The occurence and diagnosis of biomarkers of ethyl alcohol consumption
PublikacjaEthyl alcohol is a legal and a widely available psychoactive drug. However, its excessive consumption causes addiction. This leads to aggressive behaviors, family battery, difficulties in interpersonal relations, legal offences, suicides, car accidents and deterioration in labor productivity, what causes financial problems. Despite many social actions against alcohol consumption, this problem is still unresolved. Therefore, fast...
-
Development of chromatographic and mass spectrometry conditions for untargeted lipidomic analysis of human breast milk
PublikacjaHuman breast milk (HBM) is a complex biofluid containing components which are essential for the proper growth of the newborn (for example nutrients such as carbohydrates, proteins, lipids) and also bioactive substances. According to the literature, most of studies involving HBM nutrients investigations focused essentially on the determination of proteins. The molecular composition of lipids in HBM is not well known as the protein...
-
Obserwatory prędkości dla bezczujnikowego sterowania maszynami prądu przemiennego
PublikacjaPrzedstawiono model matematyczny uogólnionej maszyny elektrycznej rozszerzony przez wprowadzenie dodatkowych zmiennych. Na podstawie modelu rozszerzonego opracowano strukturę obserwatora prędkości maszyny uogólnionej. Zaprezentowano struktury obserwatorów prędkości dla poszczególnych rodzajów maszyn prądu przemiennego. Pokazano, że prędkość kątową wirnika można odtwarzać dla różnych typów maszyn stosując odpowiednie zmienne stanu...
-
ADAPTATION OF ENGINEERING FEA-BASED ALGORITHMS TO LCF FAILURE AND MATERIAL DATA PREDICTION IN OFFSHORE DESIGN
PublikacjaThere is an ever growing industrial demand for quantitative assessment of fatigue endurance of critical structural details. Although FEA-based calculations have become a standard in engineering design, problems involving the Low-To-Medium cycle range (101-104) remain challenging. This paper presents an attempt to optimally choose material data, meshing density and other algorithm settings in the context of recent design of the...
-
Hierarchia czynników wpływu w diagnostyce komponentów stalowych metodą statycznego pola rozproszonego
PublikacjaWśród technik badań nieniszczących obiektów stalowych (NDT) szczególną rolę pełnią techniki elektromagnetyczne, jako relatywnie tanie, czyste, szybkie i adaptowalne. Mają one jednak istotne ograniczenia, o których wydają się zapominać praktycy promujący tzw. metodę magnetycznej pamięci metali (ang. magnetic metal memory, MMM). Szczególnie dyskusyjna jest postulowana przez nich możliwość ilościowej korelacji charakterystyk pola...
-
Selection of circuit geometry for miniaturized microwave components based on concurrent optimization of performance and layout area
PublikacjaThe paper presents a framework for automated EM-driven circuit geometry selection of miniaturized microwave components. Selection of a particular layout is based directly on miniaturization rates achieved for a set of candidate circuit geometries. Size reduction of the considered structures is obtained by replacing their main building blocks (i.e., conventional transmission lines) with slow-wave composite cells and meander lines....
-
Resistance of Escherichia coli and Enterococcus spp. to selected antimicrobial agents present in municipal
PublikacjaIn this study, the susceptibility to erythromycin (E) and to trimethoprim/sulfamethoxazole (SXT) among isolates of Enterococcus spp. and Escherichia coli was tested, respectively. Both fecal indicators were detected and isolated from raw(RW) and treated wastewater (TW) as well as from samples of activated sludge (AS) collected in a local wastewater treatment plant (WWTP). Biodiversity of bacterial community in AS was also monitored...
-
Electronic structure and charge distribution in DyBa2Cu3O7: The ab initio approach
PublikacjaW pracy wykonano obliczenia kwantowomechaniczne struktury elektronowej nadprzewodzącego materiału DyBa2Cu3O7 (Dy123) metodą FP-LAPW (full potential - linearized augmented plane wave) w ramach formalizmu DFT (density functional theory) stosując przybliżenie GGA (generalized gradient approximation). Ze względu na silne oddziaływania korelacyjne elektronów 4f w atomie Dy zastosowano dodatkowo poprawkę kulombowską U w ramach modelu...
-
Forewarned Is Forearmed: Machine Learning Algorithms for the Prediction of Catheter-Induced Coronary and Aortic Injuries
PublikacjaCatheter-induced dissections (CID) of coronary arteries and/or the aorta are among the most dangerous complications of percutaneous coronary procedures, yet the data on their risk factors are anecdotal. Logistic regression and five more advanced machine learning techniques were applied to determine the most significant predictors of dissection. Model performance comparison and feature importance ranking were evaluated. We identified...
-
Design and Optimization of Metamaterial-Based 5G Millimeter Wave Antenna for Gain Enhancement
PublikacjaIn this brief, a low profile, broadband, high-gain antenna array based on optimized metamaterials (MMs) with dual-beam radiation is reported for 5G millimeters wave (mm-wave) applications. The design is a simple bow tie operating at a 5G band of 28 GHz. It consists of two bow ties with substrate integrated waveguide (SIW)-based power splitter. A broad impedance bandwidth of 26.3−29.8 GHz is obtained by appropriately combining the...
-
The effect of reduced pressure on carbon dioxide flow boiling heat transfer in minichannels
Publikacja. In the paper presented are the results of the study on the effect of reduced pressure on flow boiling heat transfer data in minichannels as well as conventional ones. That effect renders that most of heat transfer correlations fail to return appropriate results of predictions. Mostly they have been developed for the reduced pressures from the range 0.1-0.3. The special correction has been postulated to the in-house model of flow...
-
Effects of Noncontact Shoulder Tool Velocities on Friction Stir Joining of Polyamide 6 (PA6)
PublikacjaIn this study, the effects of the traverse and rotational velocities of the noncontact shoulder tool on the heat generation and heated flux during the friction stir joining of high-density polyamide 6 (PA6) polymer were investigated. The computational fluid dynamics (CFD) method was employed to simulate the thermomechanical phenomena during the friction stir joining (FSJ) process of PA6. A developed model was used to consider the...
-
Problemy z powłokami antykorozyjnymi na elementach wyposażenia obiektów mostowych
PublikacjaOpisano problem wadliwości zabezpieczenia antykorozyjnego w zakresie malarskich powłok ochronno-dekoracyjnych wykonywanych na stalowych elementach barier zabezpieczonych uprzednio poprzez ocynkowanie metodą zanurzeniową na gorąco. Wykorzystując przykłady pochodzące z różnych obiektów przedstawiono powtarzający się problem delaminacji powłok malarskich, niezależny od rodzaju zastosowanych wyrobów lakierniczych oraz znacznego rozwoju...
-
Problemy z powłokami antykorozyjnymi na elementach wyposażenia obiektów mostowych
PublikacjaPrzedstawiono problem wadliwości zabezpieczenia antykorozyjnego w zakresie malarskich powłok ochronno - dekoracyjnych wykonywanych na stalowych elementach barier zabezpieczonych uprzednio poprzez ocynkowanie metodą zanurzeniową. Wykorzystując przykłady pochodzące z różnych obiektów przedstawiono powtarzający się problem delaminacji powłok malarskich, niezależny od rodzaju zastosowanych wyrobów lakierniczych oraz znacznego rozwoju...
-
Customization of UWB 3D-RTLS Based on the New Uncertainty Model of the AoA Ranging Technique
PublikacjaThe increased potential and effectiveness of Real-time Locating Systems (RTLSs) substantially influence their application spectrum. They are widely used, inter alia, in the industrial sector, healthcare, home care, and in logistic and security applications. The research aims to develop an analytical method to customize UWB-based RTLS, in order to improve their localization performance in terms of accuracy and precision. The analytical...
-
Pojazdy autonomiczne na przykładzie samojeżdżącego samochodu Google`a
PublikacjaPod pojęciem pojazdu autonomicznego rozumiemy pojazdy zdolne do poruszania się bez udziału człowieka. Nie jest to nowa koncepcja, powstanie samej idei datuje się na lata 20 XX wieku, a początki wprowadzania jej w życie na lata 80. Obecnie istnieją głównie w formie prototypów będących w trakcie testów. Do jednych z najbardziej obiecujących zaliczyć możemy pojazd firmy Google. Pojazdy te zdolne są do wykrywania przeszkód znajdujących...
-
Collision-Free Network Exploration
PublikacjaA set of mobile agents is placed at different nodes of a n-node network. The agents synchronously move along the network edges in a collision-free way, i.e., in no round may two agents occupy the same node. In each round, an agent may choose to stay at its currently occupied node or to move to one of its neighbors. An agent has no knowledge of the number and initial positions of other agents. We are looking for the shortest possible...
-
Towards classification of patients based on surface EMG data of temporomandibular joint muscles using self-organising maps
PublikacjaThe study considers the need for an effective method of classification of patients with a temporomandibular joint disorder (TMD). The self-organising map method (SOM) was applied to group patients and used together with the cross-correlation approach to interpret the processed (rectified and smoothed by using root mean square (RMS) algorithm) surface electromyography signal (sEMG) obtained from testing the muscles (two temporal...
-
Autocorrelation function for the chosen effective potential of the diatomic silver anion
Dane BadawczeThe process of a two-channel decay of the diatomic silver anion (Ag2-), namely the spontaneous electron ejection giving Ag2 + e- and the dissociation leading to Ag- + Ag is theoretically studied. The ground state potential energy curves (PECs) of the neutral silver dimer and anionic silver diatomic molecule are calculated using the single reference...
-
Non-adiabatic coupling elements between the diatomic silver anion and neutral silver dimer plus continuum electron
Dane BadawczeThe process of a two-channel decay of the diatomic silver anion (Ag2-), namely the spontaneous electron ejection giving Ag2 + e- and the dissociation leading to Ag- + Ag is theoretically studied. The ground state potential energy curves (PECs) of the neutral silver dimer and anionic silver diatomic molecule are calculated using the single reference...
-
Zastosowanie audytu wewnętrznego u operatorów produkcyjnych w zapobieganiu kryzysom-studium przypadku
PublikacjaGłównym tematem artykułu była analiza badań przeprowadzonych u producenta farb proszkowych przedsiębiorstwa X, w zakresie zastosowania audytu wewnętrznego, jako metody pozwalającej na zapobieganie pojawienia się kryzysu. Właściwa współpraca operatorów produkcyjnych z menedżerami ma kluczowe zna-czenie dla budowy właściwej pozycji audytu wewnętrznego w przedsiębiorstwie X. Brak należytej współpracy na etapie badań, przy braku...
-
ANALIZA PRZEPUSTOWOŚCI WYBRANEGO UKŁADU TOROWEGO W PRZESTRZENI CZĘŚCIOWO – UPORZĄDKOWANEJ
PublikacjaNa sieci kolejowej istotny wpływ na płynność ruchu mają odpowiednio usytuowane odcinki odstępowe. Z podobną sytuacją mamy do czynienia przy modernizacji stacji kolejowych i tworzeniu nowych rozwiązań, w których należy uwzględnić prognozy rozwoju ruchu na danym elemencie sieci kolejowej. Jednak w przypadku stacji sytuacja staje się dużo bardziej skomplikowana i kosztowna, gdyż poprawa przepustowości wymaga istotnych zmian organizacyjnych...
-
Immunoanalityka – użyteczne podejście analityczne w badaniach środowiska
PublikacjaWażnym krokiem w rozwoju bezpośrednich metodyk analitycznych było opracowanie technik immunoanalitycznych. Początkowo znalazły one zastosowanie praktyczne w analityce medycznej a później także w analityce środowiskowej. Dzięki temu możliwe jest ilościowe oznaczenie stosunkowo szerokiego spektrum ksenobiotyków w próbkach charakteryzujących się złożonym składem matrycy bez praco- i czasochłonnego etapu przygotowania tych próbek do...
-
Dynamic GNSS Mission Planning Using DTM for Precise Navigation of Autonomous Vehicles
PublikacjaNowadays, the most widely used method for estimating location of autonomous vehicles in real time is the use of Global Navigation Satellite Systems (GNSS). However, positioning in urban environments using GNSS is hampered by poor satellite geometry due to signal obstruction created by both man-made and natural features of the urban environment. The presence of obstacles is the reason for the decreased number of observed satellites...
-
Active Dynamic Infrared Thermal Imaging in Burn Depth Evaluation
PublikacjaThe aim of this study was to find the relationship between active dynamic thermography (ADT) with cold excitation and burn depth. This new modality of evaluation of burns seems to be an attractive proposal for quantitative classification, allowing proper choice of burn wound treatment: conservative or surgical, especially compared with static thermography. The work was an in vivo experiment on domestic pigs, and a small number...
-
ANALYSIS OF CLIMATIC ZONES IN POLAND WITH REGARD TO ASPHALT PERFORMANCE GRADING
PublikacjaTowards the end of the last century a new system of bitumen grading was developed and implemented as part of the American Strategic Highway Research Program (SHRP). Its aim was to better adjust the testing methods and requirements for road bitumens to the actual conditions in which those bitumens serve in road pavements. Currently in Poland, similarly as in the other EU countries, road bitumens are tested and classified with regard...
-
Numerical Simulations and Tracer Studies as a Tool to Support Water Circulation Modeling in Breeding Reservoirs
PublikacjaThe article presents a proposal of a method for computer-aided design and analysis of breeding reservoirs in zoos and aquariums. The method applied involves the use of computer simulations of water circulation in breeding pools. A mathematical model of a pool was developed, and a tracer study was carried out. A simplified model of two-dimensional flow in the form of a biharmonic equation for the stream function (converted into...
-
Selection of physiological parameters for optoelectronic system supporting behavioral therapy of autistic children
PublikacjaIn this article the procedure of selection of physiological parameters for optoelectronic system supporting behavioral therapy of autistic children is proposed. Authors designed and conducted an experiment in which a group of 30 health volunteers (16 females and 14 males) were examined. Under controlled conditions people were exposed to a stressful situation caused by the picture or sound (1kHz constant sound, which was gradually...
-
System supporting behavioral therapy for children with autism
PublikacjaIn this paper, a system supporting behavioral therapy for autistic children is presented. The system consists of sensors network, base station and a brooch indicating person's emotional states. The system can be used to measure values of physiological parameters that are associated with changes in the emotional state. In the future, it can be useful to inform the autistic child and the therapist about the emotional state of the...
-
Quality Parameters in IMS/NGN Networks
PublikacjaThe Next Generation Network (NGN) architecture, including elements of the IP Multimedia Subsystem (IMS) concept, is a proposition of a telecommunication network dedicated to the needs of current and future information society. The main goal of NGN is to provide Quality of Service (QoS), for which proper network design is necessary with respect to among others standardized call processing performance parameters, including expected...
-
COMPOSITE MATERIAL SELECTION FOR A PATIENT TRANSFER ASSIST DEVICE
PublikacjaLaminates - layered composites containing at least two elements (matrix and reinforcement) widely used in industry have also found their usage in medicine. Their main feature is the ability to modify the material in order to obtain the required properties. Depending on the needs, we can modify reinforcement, type of resin or the method of bonding substrates. Commonly used fibers are: carbon fiber, glass and aramid fibers; resins...
-
Synthesis, thermal, structural and electrical properties of vanadium-doped lithium-manganese-borate glass and nanocomposites
PublikacjaA glassy sample with a nominal formula LiMn1−3x/2VxBO3 (where x = 0.05) was synthesised using the melt-quenching method. Material was characterised by differential thermal analysis (DTA), X-ray diffactometry (XRD) at room temperature and as a function of temperature (HT-XRD), X-ray photoelectron spectroscopy (XPS), impedance spectroscopy (IS) and scanning electron microscopy (SEM). Dependences of glass transition and crystallisation...
-
Ammonia amendment promotes high rate lactate production and recovery from semi-continuous food waste fermentation
PublikacjaIn this study, a reliable approach using ammonia nitrogen was proposed to increase lactate production during semi-continuous food waste (FW) fermentation under mesophilic conditions. Both free ammonia nitrogen (FAN) and ammonium ion (NH4+-N) were present in mesophilic reactors, with a wide FAN/NH4+-N ratio variation due to the intermittent pH control. The investigation of responsible mechanisms revealed that the increased production...
-
Radioisotope measurement of selected parameters of liquid-gas flow using single detector system
PublikacjaTo determine the parameters of two-phase flows using radioisotopes, usually two detectors are used. Knowing the distance between them, the velocity of the dispersed phase is calculated based on time delay estimation. Such a measurement system requires the use of two gamma-ray sealed sources. But in some situations it is also possible to determine velocity of dispersed phase using only one scintillation probe and one gamma-ray source....
-
Distribution of relaxation times as a method of separation and identification of complex processes measured by impedance spectroscopy
PublikacjaImpedance spectroscopy is one of the most commonly performed measurements to characterize electronic and electrochemical systems. Impedance spectra have limited resolution and many different processes may overlap what could be the reason of obstructions in its proper later analysis. Up to date, there are three approaches to solve this problem: examining impedance spectra itself, fitting spectra with equivalent circuits, and calculating...
-
Nano-structured Pt embedded in acidic salts of heteropolymolybdate matrices: MS EXAFS study
PublikacjaA structural study of Pt nano-catalysts is presented in the paper. The innovation in the case of the considered catalytic materials resides in the use a meso-microporous inorganic matrix of heteropolyacid salt of composition X2.5H0.5YMo12O40 where X = Rb, Cs and Y = P, Si as a catalyst support. Metallic nanoparticles were created by platinum ions reduction in a hot H2/Argon stream and were mainly located into matrix pores. As the...