Wyniki wyszukiwania dla: POWER CONVERSION
-
Transient States during Short-circuit in a Line Powered by UPS and its Impact on Earth Fault Loop Impedance Measurement and Power Quality
PublikacjaThe short-circuit in a line powered by Uninterruptible Power Supply (UPS) during different UPS operation modes is presented in the article. The transient state condition related to the short-circuit in a line fed from double conversion On-line UPS is discussed in detail. The results of the measurements of earth fault loop impedance (FLI) in circuits powered by UPS with the instruments of various manufacturers are presented. The...
-
Instantaneous power signal measurements for bearing diagnostics
Dane BadawczeBearing diagnostics can be carried out based on the method, which relies on the measurement and analysis of the variability of the signal instantaneous power, defined as the product of instantaneous current and voltage power supplied to the engines. Bearing damage causes the appearance of deformations, which are in the form of additional harmonic components...
-
Analysis and Risk Evaluation on the Case of Alteration, Revitalization and Conversion of a Historic Building in Gdańsk
PublikacjaEach investment plan, including the one concerning a building, is exposed to the consequences of various types of threats taking place. Therefore, in the case of some large-scale, atypical and complicated building ventures, some actions included in the procedure of risk management should be taken. This will allow for the risk to be eliminated or limited. While preparing a building venture, an investor does not possess full information...
-
Key issues in modeling and optimization of lignocellulosic biomass fermentative conversion to gaseous biofuels
PublikacjaThe industrial-scale production of lignocellulosic-based biofuels from biomass is expected to benefit society and the environment. The main pathways of residues processing include advanced hydrolysis and fermentation, pyrolysis, gasification, chemical synthesis and biological processes. The products of such treatment are second generation biofuels. The degree of fermentation of organic substances depends primarily on their composition...
-
Energy conversion in small water plants with variable speed PM generator
Publikacja -
Fermentative Conversion of Two-Step Pre-Treated Lignocellulosic Biomass to Hydrogen
PublikacjaFermentative hydrogen production via dark fermentation with the application of lignocellulosic biomass requires a multistep pre-treatment procedure, due to the complexed structure of the raw material. Hence, the comparison of the hydrogen productivity potential of different lignocellulosic materials (LCMs) in relation to the lignocellulosic biomass composition is often considered as an interesting field of research. In this study,...
-
A method for preliminary estimation of the length of midship body block to be inserted during ship’s conversion
PublikacjaThe paper presents a method for preliminary estimation of the length of the midship body block, which inserted in the original hull, increases the deadweight of the ship in line with a required quantity. The method may be useful for establishing the scope of conversion to better adjust the ship for transportation tasks. The problem is formulated by using a mathematical model so selected that its solution, under set of assumptions,...
-
Feasibility Study of Three-Phase Modular Converter for Dual-Purpose Application in DC and AC Microgrids
PublikacjaThe modern concept of a universal converter is intended as a power converter suitable for application in both dc or ac grids using the same external connectors. This novel family was recently proposed to allow an easier integration of renewable energy sources and energy storage systems, interfacing with dc/ac grids and/or loads with a minimum redundancy of power switches and passive elements. This kind of solution and applications...
-
Analysis of the instantaneous power signal for bearing diagnostics -bearing damaged
Dane BadawczeThe attached dataset contains the measurement results of the instantaneous values of current and voltage, recorded during the diagnostics of a damaged bearing. Bearing diagnostics can be carried out based on the method, which relies on the measurement and analysis of the variability of the signal instantaneous power, defined as the product of instantaneous...
-
Analysis of the instantaneous power signal for bearing diagnostics - bearing undamaged
Dane BadawczeThe attached dataset contains the measurement results of the instantaneous values of current and voltage, recorded during the diagnostics of an undamaged bearing. Bearing diagnostics can be carried out based on the method, which relies on the measurement and analysis of the variability of the signal instantaneous power, defined as the product of instantaneous...
-
Manufacturing and Recycling Impact on Environmental Life Cycle Assessment of Innovative Wind Power Plant Part 2/2
PublikacjaThe process of conversion of wind kinetic energy into electricity in innovative wind power plant emits practically no harmful substances into the environment. However, the production stage of its components requires a lot of energy and materials. The biggest problem during production plan-ning process of an innovative wind power plant is selection of materials and technologies and, consequently, the waste generated at this stage....
-
Feasibility Study of Three-Phase Modular Converter for Dual-Purpose Application in DC and AC Microgrids
PublikacjaThe modern concept of a universal converter is intended as a power converter (PC) suitable for application in both dc or ac grids using the same external connectors. This novel family was recently proposed to allow easier integration of renewable energy sources and energy storage systems (ESSs), interfacing with dc/ac grids and/or loads with a minimum redundancy of power switches and passive elements. This kind of solution and...
-
An Ultra-Low-Energy Analog Comparator for A/D Converters in CMOS Image Sensors
PublikacjaThis paper proposes a new solution of an ultra-low-energy analog comparator, dedicated to slope analog-to-digital converters (ADC), particularly suited for CMOS image sensors (CISs) featuring a large number of ADCs. For massively parallel imaging arrays, this number may be as high as tens-hundreds of thousands ADCs. As each ADC includes an analog comparator, the number of these comparators in CIS is always high. Detailed analysis...
-
Pipelined sceling of signed residue numbers with the mixed-radix conversion in the programmable gate array
PublikacjaIn this work a scaling technique of signed residue numbers is proposed. The method is based on conversion to the Mixed-Radix System (MRS) adapted for the FPGA implementation. The scaling factor is assumed to be a moduli product from the Residue Number System (RNS) base. Scaling is performed by scaling of terms of the mixed-radix expansion, generation of residue reprezentation of scaled terms, binary addition of these representations...
-
Relationship between conversion rate of glucosinolates to isothiocyanates/indoles and genotoxicity of individual parts of Brassica vegetables
PublikacjaThe studies on the characterisation of glucosinolates (GLs) and their breakdown products in Brassicaceae species focus mainly on the edible parts. However, other products, e.g., dietary supplements, may be produced also from non-edible parts such as roots or early forms of growth: seeds or sprouts. Biological activity of these products depends on quantitative and qualitative GL composition, but is also strictly determined by GL...
-
Ag modified ZnO microsphere synthesis for efficient sonophotocatalytic degradation of organic pollutants and CO2 conversion
PublikacjaThe synthesis and design of non-precious and efficient sonophotocatalyts by an environment friendly technique are requisites for solar energy conversion and environmental remediation. This work reports the preparation of Ag/ZnO microspheres with different Ag contents through deposition–precipitation method for pollutant degradation and CO2 conversion. Detail structural investigation reveals that ZnO microspheres and Ag-ZnO microspheres...
-
Thermochemical Conversion of Biomass and Municipal Waste into Useful Energy Using Advanced HiTAG/HiTSG Technology
PublikacjaAn advanced thermal conversion system involving high-temperature gasification of biomass and municipal waste into biofuel, syngas or hydrogen-rich gas is presented in this paper. The decomposition of solid biomass and wastes by gasification is carried out experimentally with a modern and innovative regenerator and updraft continuous gasifier, among others. A ceramic high-cycle regenerator provides extra energy for the thermal conversion...
-
High Temperature Air/Steam Conversion of Biomass and Wastes Into Fuel Gas for Heat and Electricity Production
PublikacjaPaper present principle of high temperature air/staem gasification as well as some results of research using this technology for conversion of biomass and wastes into fuel gas.
-
Green method of conversion of geraniol to value-added products in the presence of selected minerals
Publikacja -
Integration of multi-interface conversion channel using FPGA for modular photonic network
Publikacja -
Higher harmonics of converter currents in energy conversion system of small water plants
Publikacja -
Efficiency analysis of an energy conversion system for a variable speed small hydropower plant
Publikacja -
Conditions for measurement, analog-to-digital conversion and frequency analysis of irregularities of profile surface
PublikacjaPrzedstawiono uwarunkowania pomiaru, przetwarzania analogowo-cyfrowego i analizy częstotliwościowej nierówności powierzchni toczonych dla celów rozpoznawania ich głównych składowych. Przedstawiono ograniczenia w pomiarze igłą, która odwzorowuje nierówności poprzeczne. Podano zależności parametrów pomiaru cyfrowego nierówności warunkujące zakresy ich rozpatrywania. Dla wartości przedziału próbkowania, dla którego nie jest spełnione...
-
Nitrogen conversion during treatment of various type of wastewater in multistage treatment wetlands
PublikacjaThe objective of this investigation was to recognize nitrogen speciation during wastewater treatment in three multistage TWs (MTWs), which are assuming more a most effective in nitrogen removal than single stage TWs. Carried out investigations and analysis enable for determination of conditions, relationships and processes responsible for nitrogen conversions in subsequent stages of MTWs. In treated wastewater and reject water...
-
Effectiveness of a dual surface modification of metallic interconnects for application in energy conversion devices
PublikacjaA dual surface modification of an SOFC metallic interconnect with a Gd2O3 layer and an MnCo2O4 coating was evaluated. The tested samples were oxidized for 7000 h in air at 1073 K. Oxidation products were characterized using XRD, SEM-EDS, and confocal Raman imaging, and ASR was measured. The effect of gadolinium segregation at grain boundaries in Cr2O3 was evaluated using S/TEM-EDS. Area specific-resistance was measured and fuel...
-
Hybrid geothermal-fossil power cycle analysis in a Polish setting with a focus on off-design performance and CO2 emissions reductions
PublikacjaGrowing demand for electricity due to economic development contributes to increased greenhouse gas production, especially CO2. However, emissions can be limited by enhancing the efficiency of primary energy conversion, such as integrating geothermal energy into coal-fired power plants. Therefore, this paper proposes replacing conventional feed-water heaters with geothermal preheaters to create a hybridized system. This study was...
-
Low cost microwave X-band generator
PublikacjaA low cost microwave X-band generator for educational purposes was designed and built. Its simple construction and user's interface makes it suitable for a student laboratory.The generator is based on a single frequency conversion concept. It uses a digitally tunable PLL chip for intermediate frequency generation and an active frequency multiplier for frequency conversion. The generator covers 9,7 - 11 GHz part of the X frequency...
-
Efficiency limit of excitonic photovoltaic cells under phosphor-based white LED illumination
PublikacjaThe limit of energy conversion of excitonic photovoltaic cells working under white light illumination generated by phosphor-based LED is analysed using the modified Giebink approach. Particularly, the impact of the optical energy gap and energy loss associated with the excitons dissociation at the heterojunction interface on power conversion efficiency of the device are discussed. From the results of our study it follows that the...
-
Design of an Autonomous IoT Node Powered by a Perovskite-Based Wave Energy Converter
PublikacjaThis paper presents the results of experimental research focused on wave energy harvesting and its conversion to power Internet of Things (IoT) devices. The harvesting and conversion process was performed using a wave energy converter (WEC) consisting of a lead zirconate titanate piezoelectric ceramic perovskite material and a prototype power electronic circuit. The designed WEC was considered as a power supply for an end node...
-
Modeling of Electrified Transportation Systems Featuring Multiple Vehicles and Complex Power Supply Layout
PublikacjaThe paper proposes a novel approach to modeling electrified transportation systems. The proposed solution reflects the mechanical dynamics of vehicles as well as the distribution and losses of electric supply. Moreover, energy conversion losses between the mechanical and electrical subsystems and their bilateral influences are included. Such a complete model makes it possible to replicate, e.g., the impact of voltage drops on vehicle...
-
Hybrid‐mode single‐slope ADC with improved linearity and reduced conversion time for CMOS image sensors
PublikacjaIn the paper, a single‐slope analog‐to‐digital converter (ADC) for integrated CMOS image sensor applications with an improved technique of conversion has been proposed. The proposed hybrid‐mode ADC automatically uses one of the following conversion techniques: time based (i.e. PWM) or voltage based (i.e. single‐slope). During the ADC operation, the clock frequency and reference voltage are modified in order to reduce the conversion...
-
Old Problems - New Solutions: Conversion of Capitals as a Tool for Shaping the Competitive Position in the Economic Field
PublikacjaThe acts and operations any social actor effectuates in each of the logically distinguished spheres of reality are conditioned by many factors, among which a reliable analysis of the strengths and weaknesses of an agent should be considered of utmost importance. The concept of capitals presented in this article divides the quantity of resources available to all acting agents into four main categories (which allows for determining...
-
Old Problems - New Solutions: Conversion of Capitals as a Tool for Shaping the Competitive Position in the Economic Field
PublikacjaThe acts and operations any social actor effectuates in each of the logically distinguished spheres of reality are conditioned by many factors, among which a reliable analysis of the strengths and weaknesses of an agent should be considered of utmost importance. The concept of capitals presented in this article divides the quantity of resources available to all acting agents into four main categories (which allows for determining...
-
Scaling of signed residue numbers with mixed-radix conversion in FPGA with extended scaling factor selection
PublikacjaA scaling technique of signed residue numbers in FPGA is proposed. The technique is based on conversion of residue numbers to the Mixed-Radix System (MRS). The scaling factor is assumed to be a moduli product from the Residue Number System (RNS) base. Scaling is performed by scaling of MRS terms, the subsequent generation of residue representations of scaled terms, binary addition of these representations and generation of residues...
-
Ultraviolet to near-infrared down-conversion in Bi3+–Yb3+ co-doped YAM phosphor
Publikacja -
Sustainable polylysine conversion to nitrogen‐containing porous carbon flakes: Potential application in supercapacitors
Publikacja -
Thermochemical conversion strategies of biomass to biofuels, techno-economic and bibliometric analysis: A conceptual review
Publikacja -
Direct conversion of biomass to nanoporous activated biocarbons for high CO2 adsorption and supercapacitor applications
Publikacja -
ChemInform Abstract: Modern Methods of Thermochemical Biomass Conversion into Gas, Liquid and Solid Fuels
Publikacja -
Synthesis and photo-conversion of androsta- and pregna-5,7-dienes to vitamin D3-like derivatives
Publikacja -
Engineering TADF, Mechanochromism, and Second Harmonic Up- conversion Properties in Regioisomeric Substitution Space
PublikacjaThis research article explores the distinct TADF efficiency of three donor-acceptor based regio-isomers: DPAOCN (ortho- isomer), DPAMCN (meta-isomer), and DPAPCN (para-isomer). DPAPCN exhibits maximum TADF efficiency in both solution and solid-state with an impressive reverse inter-system crossing (RISC) rate of ~ 106 s-1; the underlying cause being the minimum singlet-triplet splitting energy or ∆EST and maximum SOC (spin-orbit...
-
Influence of conductive carbon and MnCo2O4 on morphological and electrical properties of hydrogels for electrochemical energy conversion
PublikacjaIn this work, a strategy for one-stage synthesis of polymer composites based on PNIPAAm hydrogel was presented. Both conductive particles in the form of conductive carbon black (cCB) and MnCo2O4 (MCO) spinel particles were suspended in the three-dimensional structure of the hydrogel. The MCO particles in the resulting hydrogel composite acted as an electrocatalyst in the oxygen evolution reaction. Morphological studies confirmed...
-
The Staged Combustion of Meat-and-Bone Meal:The Characteristics of Conversion Sub-processes and Large-Scale Process Outputs
Publikacjat Organic waste has been playing an increasingly important role in the energy market as those that may support the economies in pursuing towards decarbonization by increasing the share of renewables in the overall energy balance. In this group of alternative fuels, meat-and-bone meals being a post-production waste of the steadily developing meat industry, constitute a considerable proportion. Though they are rich in minerals, their...
-
Simulation of perovskite-based CuI/CH3NH3PbI3/TiO2 solar cell performance
Dane BadawczeThe presented data set is part of the theoretical research on novel thin-layer lead-halide perovskite solar cells with different inorganic transparent conductive oxides used as charge transport layers. In this study CuI/CH3NH3PbI3/TiO2 model structure (Model 1) was investigated by the use of the SCAPS-1D simulation method (https://scaps.elis.ugent.be/).
-
Simulation of perovskite-based CuI/CH3NH3PbI3/SnO2 solar cell performance
Dane BadawczeThe presented data set is part of the theoretical research on novel thin-layer lead-halide perovskite solar cells with different inorganic transparent conductive oxides used as charge transport layers. In this study CuI/CH3NH3PbI3/SnO2 model structure (Model 2) was investigated by the use of the SCAPS-1D simulation method (https://scaps.elis.ugent.be/).
-
Simulation of perovskite-based CuI/CH3NH3PbI3/ZnO solar cell performance
Dane BadawczeThe presented data set is part of the theoretical research on novel thin-layer lead-halide perovskite solar cells with different inorganic transparent conductive oxides used as charge transport layers. In this study CuI/CH3NH3PbI3/ZnO model structure (Model 3) was investigated by the use of the SCAPS-1D simulation method (https://scaps.elis.ugent.be/).
-
Exergy analysis of the Szewalski cycle with a waste heat recovery system
PublikacjaThe conversion of a waste heat energy to electricity is now becoming one of the key points to improve the energy efficiency in a process engineering. However, large losses of a low-temperature thermal energy are also present in power engineering. One of such sources of waste heat in power plants are exhaust gases at the outlet of boilers. Through usage of a waste heat regeneration system it is possible to attain a heat rate of approximately...
-
Up-conversion white emission and other luminescence properties of a YAG:Yb2O3·Tm2O3·Ho2O3@SiO2 glass-nanocomposite
PublikacjaWe report on a glass-nanocomposite material consisting of yttrium aluminum garnet (Y3Al5O12, YAG) nanocrystals co-doped with Yb3+, Tm3+ and Ho3+ ions as well as entrapped into a SiO2 xerogel. This 94YAG·5Yb2O3·0.8Tm2O3·0.2Ho2O3@SiO2 (abbr. YAG:YbTmHo@SiO2) nanocomposite material has been prepared by sol–gel procedure. Its structure and morphology has been characterized by means of X-ray diffraction (XRD) and scanning electron microscope...
-
Cross-Lingual Knowledge Distillation via Flow-Based Voice Conversion for Robust Polyglot Text-to-Speech
PublikacjaIn this work, we introduce a framework for cross-lingual speech synthesis, which involves an upstream Voice Conversion (VC) model and a downstream Text-To-Speech (TTS) model. The proposed framework consists of 4 stages. In the first two stages, we use a VC model to convert utterances in the target locale to the voice of the target speaker. In the third stage, the converted data is combined with the linguistic features and durations...
-
The Effect of Sodium Tetrafluoroborate on the Properties of Conversion Coatings Formed on the AZ91D Magnesium Alloy by Plasma Electrolytic Oxidation
PublikacjaMagnesium and its alloys are widely used in many areas because of their light weight, excellent dimensional stability, and high strength-to-weight ratio. However, the material exhibits poor wear and corrosion resistance, which limits its use. Plasma electrolytic oxidation (PEO) is an effective surface modification method for producing ceramic oxide layers on Mg and their alloys. The influence of the additions of sodium tetrafluoroborate...