Filtry
wszystkich: 504
Wyniki wyszukiwania dla: STRUCTURAL DAMAGE
-
Improved calculation of damage due creep by more accurate time to rupture data representation
PublikacjaReguła Robinsona (Linear Life Fraction Damage Rule) jest stosunkowo łatwa w użyciu dla różnorodnych warunków obciążenia. Z tego powodu jest ona powszechnie akceptowana i używana. Potencjalne możliwości poprawy dokładności obliczeń tą metodą daje zastosowanie specjalnych funkcji do aproksymacji wyników badań wytrzymałości czasowej. W pracy zaproponowano zastosowanie funkcji typu Spline oraz bardzo elastycznej funkcji Spline3D do...
-
Short Term Monitor of Photodegradation Processes in Ranitidine Hydrochloride Observed by FTIR and ATR FTIR
PublikacjaThe effects of degradation of ranitidine hydrochloride exposed to UVB radiation (l = 310 nm) and oxygen in a weathering chamber were studied by Fourier Transform Infrared spectroscopy (FTIR) and Attenuated Total Reflectance Fourier Transform Infrared spectroscopy (ATR-FTIR). ATR-FTIR profile indicated that the degradation was spatially heterogeneous. Significant amounts of photoproducts were detected only in a directly...
-
NUMERICAL MODELLING AND EXPERIMENTATION OF HISTORICAL CARPENTRY CORNER LOG JOINTS
PublikacjaThe main purpose of this research is to determine the stress distributions on the contact surfaces between the logs of the historical carpentry corner joints. The additional purpose is to compare the stress distribution for four different boundary conditions in the case of dry and wet pine wood. The paper presents the results of numerical analysis of the shortcorner dovetail connection and the saddle notch corner joint, which are...
-
Research on causes of corrosion in the municipal water supply system
PublikacjaThis paper presents results of failure analysis study to characterize the corrosion damage that occurred in the water supply system in Krakow. This analysis includes: electrochemical noise, linear polarization and resistometric measurements. Water aggressiveness of four water intakes was defined using Langelier and Ryznar indices. Results from this indices did not reveal the causes of considerable corrosion losses in water systems....
-
Radio- and photosensitization of DNA with compounds containing platinum and bromine atoms
Publikacja. Irradiations of plasmid DNA by both X-rays and UV light in the presence and absence of compounds containing platinum and bromine atoms were performed in order to asses the sensitization potential of these compounds. Plasmid DNA pBR322 was incubated with platinum (II) bromide, hydrogen hexabromoplatinate (IV), hydrogen hexahydroxyplatinate (IV) and sodium hexahydroxyplatinate (IV). Incubation was followed by X-ray or UV irradiations....
-
Application of guided wave propagation in diagnostics of steel bridge components
PublikacjaEarly detection of potential defects and identification of their location are necessary to ensure safe, reliable and long-term use of engineering structures. Non-destructive diagnostic tests based on guided wave propagation are becoming more popular because of the possibility to inspect large areas during a single measurement with a small number of sensors. The aim of this study is the application of guided wave propagation in...
-
Vibration monitoring of structures in the light of the Polish and international requirements
PublikacjaThe paper concerns the wide range of strategies used to protect structures against man-made dynamic excitation. The most popular approaches applied worldwide are compared, and the main differences and similarities are summarized. The literature studies are supported by the results of the measurements performed on different types of real structures, which are sensitive and insensitive to the dynamic load. To make the conclusions...
-
Modeling, simulation, and validation of a TB41 crash test of the H2/W5/B concrete vehicle restraint system
PublikacjaThe paper addresses numerical simulations of a concrete vehicle restraint system. The model is described in detail. The advanced material law of the continuous surface cap model was used to analyze the damage locations in concrete barrier segments. The results were validated against the TB41 full-scale crash test. The test was conducted in compliance with European standard EN 1317, and the validation was performed in accordance...
-
Performance of organic coatings upon cyclic mechanical load
PublikacjaA number of engineering structures fail due to the fatigue damage resulting from cyclic mechanical stress. However, as far as organic coatings are concerned this degradation factor remains underestimated. In the paper the authors propose a methodology combining global electrochemical impedance spectroscopy and local atomic force microscopy measurements for evaluation of coating resistance to an impact of repetitive mechanical stress. Typical...
-
Nanofiltration in the food industry
PublikacjaNanofiltration (NF), as a pressure-driven membrane process, has been widely demonstrated to have great potential for food processing applications. There are several advantages of this membrane process over traditional methods that makes NF suitable for food processing, such as the low thermal damage to the product, higher aroma retention, lower energy consumption, and low maintenance costs. In this chapter, according to the recent...
-
A Computational Analysis of the Aerodynamic and Aeromechanical Behavior of a Thermo-Well for Steam Temperature Measurement in a Steam Turbine
PublikacjaThe goal of the paper is twofold: firstly, it presents computational fluid dynamics analysis for finding maximum unsteady flow forces (and their frequencies) acting on a thermo-well for measuring steam temperature in a steam turbine control stage and secondly, it presents computational solid dynamics analysis of possibility of entry into resonance of the thermowell structure. There have been analyzed two cases of flow with changing...
-
Novel Nonlinear High Order Technologies for Damage Diagnosis of Complex Assets
PublikacjaFor the first time worldwide, innovative techniques, generic non-linear higher-order unnormalized cross-correlations of spectral moduli, for the diagnosis of complex assets, are proposed. The normalization of the proposed techniques is based on the absolute central moments, that have been proposed and widely investigated in mathematical works. The existing higher-order, crosscovariances of complex spectral components are not sufficiently...
-
The relationship between standard reduction potentials of catechins and biological activities involved in redox control
PublikacjaRedox homeostasis involves factors that ensure proper function of cells. The excess reactive oxygen species (ROS) leads to oxidative stress and increased risk of oxidative damage to cellular components. In contrast, upon reductive stress, insufficient ROS abundance may result in faulty cell signalling. It may be expected that dietary antioxidants, depending on their standard reduction potentials (E°), will affect both scenarios....
-
Cell-penetrating peptides – mechanism of transduction and synthesis – short review
PublikacjaPotential antimicrobial agents may be effective if they are delivered efficiently to their site of action. In many cases, lack of permeability through the cell membrane is the main problem. One of the possible solutions could be a novel intracellular delivery system involving cell-penetrating peptides (CPPs), which may improve the efficiency of many new biophar-maceuticals. Among other things, CPPs are capable of trans-porting...
-
The role of epigenetics in regeneration
PublikacjaComplex changes in chromatin structure and at the transcriptional level occur from the creation of a single parental gamete throughout fertilization, embryo development and the life of an adult organism. Epigenetic changes, such as methylation and hydroxymethylation of DNA or histone methylation and acetylation, are an important part of these processes. Epigenetic regulation has an essential influence on gene expression level. DNA...
-
Induction Motor Bearings Diagnostic Using MCSA and Normalized Tripple Covariance
PublikacjaDiagnosis of induction motors, conducted remotely by measuring and analyzing the supply current is attractive with the lack of access to the engine. So far there is no solution, based on analysis of current, the credibility of which allow use in industry. Statistics of IM bearing failures of induction motors indicate, that they constitute more than 40% of IM damage, therefore bearing diagnosis is so important. The article provides...
-
Ordered titania nanotubes layer selectively annealed by laser beam for high contrast electrochromic switching
PublikacjaThe phase conversion from amorphous into crystalline one in the selected area of as-anodized titania nanotubes was achieved via laser treatment. The optimized processing parameters enable fast, one-minute crystallization of titania within an area limited by a shadow mask and without any morphology damage of ordered TiO2 tubular film. The laser annealed titania nanotubes could be easily overgrown by a conducting polymer without...
-
Contamination of water in Oliwski Stream after the flood in 2016
PublikacjaIn the article pollution of stream waters with surface runoff from an urbanized area caused by an extremely high rainfall is discussed. The analyzes were carried out after the rainfall of the depth 152 mm which took place in Gdańsk on 14th and 15th July 2016. This extreme rainfall caused urban flooding, damage of several retention ponds and pollution of surface waters. In the article the results of physical and chemical analyzes...
-
Current based Normalized Triple Covariance as a bearings diagnostic feature in induction motor
PublikacjaDiagnosis of induction motors, conducted remotely by measuring and analyzing the supply current is attractive with the lack of access to the engine. So far there is no solution, based on analysis of current, the credibility of which allow use in industry. Statistics of IM bearing failures of induction motors indicate, that they constitute more than 40% of IM damage, therefore bearing diagnosis is so important. The article provides...
-
Current-based higher-order spectral covariance as a bearing diagnostic feature for induction motors
PublikacjaConducting the diagnosis of induction motors remotely by analyzing the supply current is an attractive prospect with the lack of access to the engine. Currently, there is no solution, based on analysis of the current, the credibility of which would allow its use in industry. The statistics of bearing failures in induction motors indicate that they constitute more than 40% of induction motor damage, therefore, bearing diagnosis...
-
Local and global response of sandwich beams made of GFRP facings and PET foam core in three point bending test
PublikacjaIn the paper behaviour of laminated sandwich beams (FRP face sheet – PET foam core – FRP face sheet) subjected to three point bending is studied. The paper aim is to find practical descriptions enabling effective and accurate estimation of the elastic response, damage and failure of the beams, basing on experiments and static calculations. Therefore a number of tests are described, that were done on laminated coupons and foam specimens...
-
VUV photofragmentation of the six-membered heterocyclic molecules containing oxygen
PublikacjaCancer is a significant public health concern worldwide, which results in millions of deaths each year. The standard cure routine for cancer is surgery, and nowadays, radiotherapy or a hadrontherapy. Depending on the type of cancer, patients may undergo additional treatment, including targeted therapy. A combination of radio- or hadron-therapy with proper drug treatment can inhibit the proliferation of cancer cells and thus can...
-
Examination of selected failure criteria with asymmetric shear stresses in the collapse analysis of laminated shells
PublikacjaThe paper is concerned with failure analysis of composite shells performed with the usage of the nonlinear 6‐parameter shell theory with drilling rotation degree of freedom. This special theory embodies naturally unlim-ited translations and rotations and is suitable for analysis of irregular shells for instance with various, partic-ularly orthogonal, intersections. The presence of the drilling rotation is inherently accompanied...
-
Zieleń miejska Gdyni okresu międzywojennego oraz problematyka jej zachowania = Urban greenery of Gdynia of interwar period and the issues of its retaining
PublikacjaURBAN GREENERY OF GDYNIA OF INTERWAR PERIOD AND THE ISSUES OF ITS RETAINING The subject of this article is the urban greenery arrangement in interwar Gdynia and the issues of its retaining after the II World War. The article will concern retaining the authenticity and integrity of the historic urban greenery of Gdynia, both greenery layouts and the plant material creating it. The author of the article will present in what...
-
Sulfate‐reducing bacteria‐assisted hydrogen‐induced stress cracking of 2205 duplex stainless steels
PublikacjaThe paper presents the results of a laboratory investigation of the microbiologically assisted hydrogen‐induced stress cracking (HISC) of 2,205 duplex stainless steel (DSS). The testing of susceptibility toward HISC was performed with two different methods. Precharged in sulfate‐reducing bacteria (SRB), inoculated medium samples were subjected to slow strain‐rate testing in artificial seawater. In situ constant load tests were...
-
Fracture surface topography investigation and fatigue life assessment of notched austenitic steel specimens
PublikacjaThe objectives of this study were to investigate the fracture surface topography of X8CrNiS18-9 austenitic stainless-steel specimens for different loadings and notch radii and to supplement the knowledge about the fracture mechanisms for fatigue performance. Cases with three different values of the notch radius ρ and the stress amplitude σa were analysed. The fracture topographies were quantified by the areas over their entire...
-
Safety issues referred to induced sheath voltages in high-voltage power cables – case study
PublikacjaLoad currents and short-circuit currents in high-voltage power cable lines are sources of the induced voltages in the power cables’ concentric metallic sheaths. When power cables operate with single-point bonding, which is the simplest bonding arrangement, these induced voltages may introduce an electric shock hazard or may lead to damage of the cables’ outer non-metallic sheaths at the unearthed end of the power cable line. To...
-
Model and laboratory simulation of a induction motor for diagnostic purposes
PublikacjaStatistics say that bearings are this part of induction motors which is most susceptible to damage. The equipment employed for bearing diagnostics usually makes use of vibrations as the criterion for technical condition of the bearings. A faulty bearing results in additional motor vibrations. They are reflected in the harmonic content of stator currents. In certain operating conditions the current signal is the sole source of information...
-
An experimental study of self-sensing concrete enhanced with multi-wall carbon nanotubes in wedge splitting test and DIC
PublikacjaConcrete is the worldwide most utilized construction material because of its very good performance, forming ability, long-term durability, and low costs. Concrete is a brittle material prone to cracking. Extensive cracking may impact durability and performance over time considerably. The addition of a small amount of carbon nanotubes (CNT) increases the concrete’s overall electrical conductivity, enabling internal structure...
-
CONSTRUCTION TECHNOLOGY OF TIMBER-FRAME HOUSES RESISTANT TO DYNAMIC LOADS – STUDY ON MODELS OF EXTERIOR WALLS
PublikacjaThe aim of this paper is to show the numeric representation of experimental studies concerning the behaviour of exterior wall models of a timber-frame house under harmonic loading. A single wall model according to traditional technology of timberframe house walls (filling with mineral wool) was tested. The analysis was conducted for the following frequencies: 0.5 Hz, 1.0 Hz, 2.0 Hz and 5.0 Hz for various values of the specified...
-
Instantaneous impedance monitoring of synergistic effect between cavitation erosion and corrosion processes
PublikacjaThe most common method of determination of cavitation erosion resistance as well as the magnitude of erosion-corrosion synergistic interaction is based on the weight loss measurements. Nondestructive characterization of installations elements is in most cases impossible to perform. Also, such a measurement does not include local types of failure or alteration of operating conditions. There is an urge to elaborate a method for monitoring...
-
Effect of Pendolino high-speed rail on the structure of buildings located the proximity of the railway tracks
PublikacjaThe following research focuses on the dynamic analysis of the impact of the high-speed train inducted vibrations on the structures located near railway tracks. The office complex chosen as the subject of calculations is located in the northern part of Poland, in Gdańsk, in the proximity of Pendolino, the high speed train route. The high speed trains are the response for the growing needs for more efficient railway system. However...
-
On degradation of glass/polyester laminate immersed in water
PublikacjaMechanical behaviour was compared for glass/ polyester laminates manufactured in the boatbuilding plant using three methods: hand lay-up, vacuum bagging, infusion. Specimens were tested in dry condition and following accelerated water immersion test (70°C- corresponding to the exposure of 30 years at 19°C). In three point bending test 40-50% reduction in laminate strength was observed due to water immersion. The highest degradation...
-
FEM modelling of stress and strain distribution in weld joints of steel sandwich panels
PublikacjaThe development of laser welding technology has enabled the mass production of thin-walled structures, including steel sandwich panels. The technology of joining plating panels with stiffeners by welding allows us to create joints with a specific geometry and material properties. In comparison with other types of joints, laser welds are characterized by their specific behaviour under cyclic load and, as a consequence, a different...
-
Comparative analysis of different numerical models of a steel radial gate
PublikacjaHydrotechnical structures are important components in water management system and general flooding safety. Their reliability should be ensured since potential damage might lead to catastrophic consequences. Weir gates are considered to be highly vulnerable elements of each hydro power plant, with regard to its dynamic resistance. The aim of the paper is to compare different numerical models and their influence on the results of...
-
Sustainable development requires risky decisions - problematic 300 ton overweight transport passing a bridge
PublikacjaOversize load passages over bridges are one of the research issues related to sustainable development that engineering and scientific teams around the world have to deal with . The article presents the scope of activities that enabled the passage of an oversized vehicle with a total weight of over 300 tons over a reinforced concrete slab. The bridge load capacity is 30 tons. In order to assess the capacity of the bridge, detailed...
-
Effect of strain level on the stiffness of cold recycled bituminous mixtures
PublikacjaCold recycling is a sustainable technology for the rehabilitation of bitumi-nous pavements. This study investigates the stiffness response of cement-bitumen treated materials (CBTM)manufactured with 80% reclaimed asphalt and treated with 2.0% Portland cement and 4.0% bitumen emulsion. Indirect tensile stiffness modulus tests were carried out to assess the strain dependence of stiffness at target horizontal deformation levels between...
-
Effect of Simultaneous Valve Closures in Hydraulic Piping Systems
PublikacjaThe paper investigates wave interference (between pressure waves) occurring in simple hydraulic systems. Water hammer was induced by simultaneous closure of three valves located at the reservoirs of a “Y” type hydraulic system. Numerical simulations were carried out with the help of the freeware computer package Allievi enabling the reader to replicate results in a direct manner. The influence of the following quantities has been...
-
Application Isssues of the Semi-Markov Reliability Model
PublikacjaPredicting the reliability of marine internal combustion engines, for instance, is of particular importance, as it makes it possible to predict their future reliability states based on the information on the past states. Correct reliability prediction is a complex process which consists in processing empirical results obtained from operating practice, complemented by analytical considerations. The process of technical state changes...
-
Finite element modelling of a historic church structure in the context of a masonry damage analysis
PublikacjaThe paper includes a case study of modelling a real historic church using the finite element method (FEM) based on laser scans of its geometry. The main goal of the study was the analysis of the causes of cracking and crushing of masonry walls. An FEM model of the structure has been defined in ABAQUS. A non-linear dynamic explicit analysis with material model including damage plasticity has been performed. A homogenization procedure...
-
Numerical simulations of overflow experiments on a model dike
PublikacjaDike failure due to overtopping is one of the important factors, which should be considered in the dike designing process. Although the overflow is characterized by the relatively low risk of occurrence, in many cases dikes are totally destroyed or seriously damaged. An interesting phenomenon occurring during overflow is the trapping of air in pores of the unsaturated soil material. As the infiltration progresses from all sides,...
-
On analysis of double-impact test of 1500-kg vehicle into w-beam guardrail system
PublikacjaEvery day on roads many scenarios of accidents may occur. One of the measures to minimize their consequences is road safety barriers. Finite Element analyses are being increasingly used to support the physical testing of these devices. The paper addresses the issue of a secondary impact into the previously damaged w-beam guardrail system. This situation belongs to one of the most dangerous which can happen on roads and may cause...
-
Tensile failure study of 3D printed PLA using DIC technique and FEM analysis
PublikacjaThe paper presents the experimental and numerical study of the failure behaviour of Fused Filament Fabricated (FFF) Polylactic Acid (PLA) samples subjected to tensile load. The examined samples are printed in flat orientation with 0◦, 45◦ and 90◦ raster angles. During the experiments the deformation of the specimens is continuously scanned with the 3D Aramis measuring system utilizing the digital imaging correlation technique,...
-
Investigations on strength and fracture in RC beams scaled along height or length
PublikacjaThe objective of the present paper is to identify experimentally and theoretically differing failure mechanisms in reinforced concrete beams subjected to four-point bending for a separate variation of the depth and length at the constant thickness. Experiments were performed on reinforced concrete beams under four-point bending. Different failure mechanisms included steel yielding, diagonal tension or shear- compression depending...
-
Nowa metoda diagnostyki stanu technicznego nakładek stykowych
PublikacjaThe current collection system, which consists of the overhead contact line and a current collector, is particularly important in electric rail vehicles, where their reliability is concerned. Faultless current collection is conditioned not only by suitable construction of these elements but also by their proper maintenance. Retaining permanent electrical contact is essential in DC systems, where current demand is relatively high. In...
-
Modelling of laminated glass PVB walls of buildings exposed to vehicle impact with different speeds
PublikacjaThis paper presents an analytical model, developed for laminated glass subjected to a low-velocity impact. It has the ability to capture glass cracks as well as large non-linear deformations. It is based mathematically on the firstorder deformation concept, which considers the effect of membrane and transverse shear as well as bending. This theory uses damage mechanics to capture the glass cracking. For this purpose, several experiments...
-
THE IDENTIFICATION OF TOXIC COMPOUND EMISSION SENSITIVITY AS A DIAGNOSTIC PARAMETER DURING DYNAMIC PROCESSES OF THE MARINE ENGINE
PublikacjaChanging some parameters of the engine structure alters the emission of harmful components in the exhaust gas. This applies in particular to the damage of charge exchange system as well as fuel system and engine supercharger. These changes are much greater during the dynamic states and their accompanying transitional processes. The different sensitivity of diagnostic parameters to the same force, coming from the engine structure,...
-
Comparison of state feedback and PID control of pressurizer water level in nuclear power plant
PublikacjaThe pressurizer water level control system in nuclear power plant with pressurized water reactor (PWR) is responsible for coolant mass balance. The main control goal is to stabilize the water level at a reference value and to suppress the effect of time-varying disturbances (e.g. coolant leakage in primary circuit pipeline system). In the process of PWR power plant operation incorrect water level may disturb pressure control or...
-
The influence of global climate change on the environmental fate of anthropogenic pollution released from the permafrost
PublikacjaThis article presents a review of information related to the influence of potential permafrost degradation on the environmental fate of chemical species which are relased and stored, classified as potential influence in future Antarctic environment. Considering all data regarding climate change prediction, this topic may prove important issue for the future state of the Antarctic environment. A detailed survey on soil and permafrost...
-
Stability of thin film diamond mirror for applications in interferometers under the short-time exposure on selected aggressive chemicals
PublikacjaIn presented study a thin boron-doped diamond film was proposed for application in the interferometry as a highly durable optical mirror. The unique properties of the diamond films, like high chemical stability and hardness, allow them to be used even in the chemically aggressive environment, where the commonly used silver mirrors can be susceptible to damage. The investigated nanodiamond layer was fabricated by uPE CVD method...