Wyniki wyszukiwania dla: CALCULATION MODEL
-
Distance measurement errors in silent FM-CW sonar with matched filtering
PublikacjaThe secretiveness of sonar operation can be achieved by using continuous frequency-modulated sounding signalswith reduced power and significantly prolonged repeat time. The application of matched filtration in the sonarreceiver provides optimal conditions for detection against the background of white noise and reverberation, and avery good resolution of distance measurements of motionless targets. The article shows that target...
-
ANALYSIS OF THE LOAD-CARRYING CAPACITY OF A HYDRODYNAMIC WATER-LUBRICATED BEARING IN A HYDROELECTRIC POwER PLANT
PublikacjaThe paper presents an analysis of the load-carrying capacity of a historic hydrodynamic water-lubricated radial bearing of an unconventional segment design installed in the Braniewo Hydroelectric Power Plant. The aim of the calculations was to determine whether the bearing operates in the conditions of hydrodynamic or mixed lubrication, as well as to establish the optimal geometry of the axial grooves allowing for the highest load-carrying...
-
Experimental study of the post tensioned prestressed concrete corbels
PublikacjaThe results of experimental investigation of 6 symmetrical double prestressed corbels of variable shear span to depth ratio and variable location of prestressing bars are presented in the paper. The post ten- sioned corbels were prestressed with Macalloy 1030 bars of 25 mm in diameter. The results of the tests were compared with the cracking and load carrying capacity of corbels reinforced with passive reinforce- ment. As a result...
-
Profitability criteria of partial cogeneration in nuclear power plant.
PublikacjaIn this paper, profitability criteria and calculation methodology of profitability conditions for partial cogeneration in nuclear power plant (NPP) was presented. Considered NPP supplies electricity to consumers through public power system, whereas heat is expected to be supplied to consumption regions via long-distance heat transport line. First proposed profitability criterion was total annual costs of electricity and heat delivered...
-
Using multibeam echoes in seafloor characterisation and classification
PublikacjaThe method of seabed identification and classification from multibeam sonar echoes is presented. The proposed approach is based on calculation of a set of parameters of an echo envelope, similarly as in seafloor classification using single beam echosounder. These parameters are extracted for each consecutive beam allowing the estimation of their dependence on the seafloor incident angle. The relation between seabed type and calculated...
-
Methods of determination of C coefficient for period of rolling vessel in calm water for example of pax cargo ship
PublikacjaThis article presents a different approach to calculate the C coefficient needed to determine the period of own rolling vessel in calm water. The C coefficient is usually adopted as the approximate value from the available literature, usually depending on the type of vessel, and less dependent on the loading condition. In experimental studies of marine properties (seakeeping) often have a problem with the selection of the correct...
-
An Analysis of Elliptical-Rectangular Multipatch Structure on Dielectric-Coated Confocal and Nonconfocal Elliptic Cylinders
PublikacjaA rigorous analysis of the resonance frequency problem of an elliptical-rectangular microstrip structure mounted on dielectric-coated elliptic conducting cylinder, with electrically small radius, is investigated in this paper. A full-wave analysis and a moment-method calculation are employed. The analysis is carried out considering the expansion of the field as a series of Mathieu functions. The complex resonance frequencies of...
-
Sensorless induction motor drive with voltage inverter and sine-wave filter
PublikacjaThis paper presents a speed sensorless control system of an induction motor with an output LC filter. It is known that the parameters design of the filter gives sine wave motor supply voltage but complicates control and estimation process. The reason is that the voltage drop and phase shift between filter input and output signals are imposed, and hence the motor voltages and currents differ from the inverter output waveforms. To...
-
Evaluation of the structures size in the liquid-gas flow by gamma-ray absorption
PublikacjaThe rapid development of tomography methods particularly electrical, X and gamma rays allows for a wide range of the information about flow structure. However, all of such methods are quite complicated. At the same time much simpler systems as the measuring system of gamma rays absorption, allows to obtain a all key flow information which describe the two-phase flow. In the article the results of analyzes of radiometric signal...
-
Study on 19th-century cast iron columns from the former financial office building in Kwidzyn
PublikacjaThe article presents the results for cast iron columns used as floor supports in the former financial office building in Kwidzyn (Poland).The stocktaking drawings provided the general and detailed data about the 19th century designer’s decisions. During the research, architectural and structural analysis was carried out. The graphics were used as a starting material for preparing 3D calculation models. The FEM-based numerical simulations...
-
Defining the thermal conductivity of thermally heterogeneous hollow wall bricks used as elements for increasing the comfort of buildings
PublikacjaThe article presents numerical calculation analysis in the scope of determining thermal conductivity coefficientλeq[W/(m·K)] of thermally heterogeneous hollow bricks of thermally heterogeneous structure (a combinationof structural material with thermal insulation material). Numerical calculations were conducted by means ofprofessional software TRISCO-KOBRU 86, serving thermal circulation analysis in a 2D field in stationary approach.The...
-
Computations of the least number of periodic points of smooth boundary-preserving self-maps of simply-connected manifolds
PublikacjaLet $r$ be an odd natural number, $M$ a compact simply-connected smooth manifold, $\dim M\geq 4$, such that its boundary $\partial M$ is also simply-connected. We consider $f$, a $C^1$ self-maps of $M$, preserving $\partial M$. In [G. Graff and J. Jezierski, Geom. Dedicata 187 (2017), 241-258] the smooth Nielsen type periodic number $D_r(f;M,\partial M)$ was defined and proved to be equal to the minimal number of $r$-periodic points...
-
Calculations of labyrinth seals with and without diagnostic extraction in fluid-flow machines
PublikacjaLabyrinth seals are essential components of steam turbine unit constructions. Two types of labyrinth seals can be named, the first of which is the seal without diagnostic steam extraction, and the second – with extraction. The distribution of flow parameters along the packing is affected remarkably by the average seal clearance. The presence of diagnostic extraction leads to the equation system which is determinable and can be...
-
The impact of the distribution network reconfiguration on active power losses: Selected issues of UPGRID project realization
PublikacjaThe dynamic development of smart grids allows the use of remote controllable switches to change the configuration of the distribution network. The paper discusses the impact of the distribution system reconfiguration on active power losses, taking into account the typical daily load profiles. Based on modified IEEE 33-bus test distribution system the article presents the method of selection the appropriate sensitivity factor and...
-
Heat Transfer During Pool Boiling of Water, Methanol and R141b on Porous Coated Horizontal Tube Bundles
PublikacjaThis paper presents the results of experimental investigation of water, methanol and R141b refrigerant boiling on horizontal porous coated tube bundles supposed to represent a flooded-type evaporator. Experiments were carried out for a bundle of 19 tubes in triangular layout for two pitch-to-diameter ratio values – 1.7 and 2.0 – in atmospheric and sub-atmospheric pressure conditions. Average heat transfer coefficients – both local,...
-
The Use of Free Adjustment and Msplit-Estimation for Determination of the Vertical Displacements in Unstable Reference System
PublikacjaThe problem of the determining of the displacements of engineering objects and their surroundings is the current and important issue in the field of engineering geodesy. Most control measurements are made in relation to reference points (stable points). On the other hand, sometimes it happens that it is not possible perform the measurements with reference to the stable points or identification of stable points is difficult. Therefore,...
-
Wind resource assessment and energy yield prediction for the small wind turbine on the Szubieniczne Hill
PublikacjaThe goal of this study is to preliminary assess the wind resources on the Szubieniczne Hill in order to predict the annual energy production for planned small wind turbine. The analyzed site is located close to the Gdańsk University of Technology campus, in complex urban environment additionally surrendered by forested hills. The assessment is based on Computational Fluid Dynamics simulations which allow to evaluate the wind energy potential...
-
The database of interpolated RR-intervals of original length 512 of 41 patients at rest hospitalized due to the episode of acute ischemic stroke
Dane BadawczeThis dataset contains the data that was a basis for the results discussed in the paper “Persistent homology as a new method of the assessment of heart rate variability” by Grzegorz Graff, Beata Graff, Paweł Pilarczyk, Grzegorz Jabłoński, Dariusz Gąsecki, Krzysztof Narkiewicz, Plos One (2021), DOI: 10.1371/journal.pone.0253851.
-
The database of interpolated RR-intervals of length 512 of 46 healthy subjects at rest
Dane BadawczeThis dataset contains the data that was a basis for the results discussed in the paper “Persistent homology as a new method of the assessment of heart rate variability” by Grzegorz Graff, Beata Graff, Paweł Pilarczyk, Grzegorz Jabłoński, Dariusz Gąsecki, Krzysztof Narkiewicz, Plos One (2021), DOI: 10.1371/journal.pone.0253851.
-
Chemical Vapor Transport Route toward Black Phosphorus Nanobelts and Nanoribbons
PublikacjaChemical vapor transport (CVT) method is widely used for bulk black phosphorus (BP) fabrication. In this work, we demonstrate that CVT provides a route for the fabrication of BP nanoribbons and nanobelts. This method consists of a two-step procedure, including initial BP column growth using the CVT technique, followed by ultrasonic treatment and centrifugation. The obtained nanostructures preserve BP column dimensions, forming...
-
SEWAGE SYSTEM CONCEPT FOR KAMIEŃ VILLAGE IN THE COMMUNE OF SZEMUD
PublikacjaThe aim of this thesis is to solve a disturbing problem, which is illegal sewage discharge, without any previous treatment in a village Kamień, Szemud commune, Poland, by developing a multivariate sewerage system concept. The introduction submits the theory concerning the division of sewer systems as well as the wastewater treatment’s level. Moreover, there is also the problem of rural sanitation presented and main locality –...
-
Joints Of Steel Sandwich Structures
PublikacjaSteel sandwich structures are perceived as alternatives to single-skin welded structures in the shipbuilding industry due its advantages like significant reduction of mass in relation to typical single skin structure. However, beside problems with their strength properties itself, applications in real structures requires of solving the problem of joining, both for connection sandwich to sandwich as well as sandwiches to single-shell...
-
Chemical Vapor Transport Route toward Black Phosphorus Nanobelts and Nanoribbons
PublikacjaChemical vapor transport (CVT) method is widely used for bulk black phosphorus (BP) fabrication. In this work, we demonstrate that CVT provides a route for the fabrication of BP nanoribbons and nanobelts. This method consists of a two-step procedure, including initial BP column growth using the CVT technique, followed by ultrasonic treatment and centrifugation. The obtained nanostructures preserve BP column dimensions, forming...
-
Technical fabrics in costruction of large scale roofs - numerical and experimental aspects
PublikacjaDesigning and construction of textile hanging roofs is the challenging subject for engineers. This type of structure needs geometrically and very often also physically non-linear calculations. Due to different behaviour of two families of threads (warp and weft), which during deformation can change the angle between their directions, they require special constitutive modelling. Also the loading of hanging roofs is very special....
-
Analytical design method of reverse curves
PublikacjaThe paper deals with a new approach relating to the design of the region of railway track direction alteration adapted to Mobile Satellite Measurements technique. The method may be particularly useful in situations when both the straights of the route directions cannot be connected in an elementary way using a circular arc with transition curves; this also refers to the application of a compound curve. Thus the only solution becomes...
-
Mobile indicators in GIS and GPS positioning accuracy in cities
PublikacjaThe publication describes the possible use of tele-geoprocessing as a synergy of modern IT solutions, telecommunications and GIS algorithms. The paper presents a possibility of urban traffic monitoring with the use of mobile GIS indicators of dedicated monitoring system designed for taxi corporation. The system is based on a stationary and mobile software package. The optimal and minimal assumptions for the monitoring of urban...
-
Influence of a Radio Frequency on RF Fingerprinting Accuracy Based on Ray Tracing Simulation
PublikacjaIn this paper the influence of a radio signal frequency on performance of Indoor Positioning System based on fingerprinting has been examined using ray-tracing simulations. It has been simulated how spatial distribution of an RF signal strength change with the signal’s frequency. The results were used to show its’ impact on the behavior of localization algorithms that are employing RSS measurements to determine node’s position...
-
Experimental research on evolutionary path planning algorithm with fitness function scaling for collision scenarios
PublikacjaThis article presents typical ship collision scenarios, simulated using the evolutionary path planning system and analyses the impact of the fitness function scaling on the quality of the solution. The function scaling decreases the selective pressure, which facilitates leaving the local optimum in the calculation process and further exploration of the solution space. The performed investigations have proved that the use of scaling...
-
Preliminary estimation of groundwater recharge on Brda river outwash plain
PublikacjaEstimation of groundwater recharge is one of the most challenging subjects in hydrogeology. It is a critical factor influencing the pollution migration, assessment of aquifer vulnerability to contamination, small-scale groundwater budget calculation, modeling of nutrient cycling and detailed flow path calculations. In Poland an infiltration rate method is widely used, which depends on a system of rate coefficients referring to...
-
An application of acoustic sensors for the monitoring of road traffic
PublikacjaAssessment of road traffic parameters for the developed intelligent speed limit setting decision system constitutes the subject addressed in the paper. Current traffic conditions providing vital data source for the calculation of the locally fitted speed limits are assessed employing an economical embedded platform placed at the roadside. The use of the developed platform employing a low-powered processing unit with a set of microphones,...
-
Low Cost Method for Location Service in the WCDMA System
PublikacjaA new and low cost method for a location service (LCS) in the Wideband Code Division Multiple Access (WCDMA) system is outlined. This method, which is called TDOA + RTT, enables calculation of the geographical position of a mobile station (MS) without knowledge of relative time differences (RTDs) between base stations (BSs). The TDOA+RTT method is based on the measurement of round trip times (RTTs) between the MS and the serving...
-
DETERMINATION OF SP3 FRACTION IN ta-C COATING USING XPS AND RAMAN SPECTROSCOPY
PublikacjaThe paper presents results of studies on the structure of tetrahedral amorphous carbon films (ta-C) with a thickness in the range from 20 to 280 nm, deposited using pulsed vacuum arc technique with an electromagnetic Venetian blind plasma filter. The results of the phase structure analysis, obtained using visible Raman spectroscopy and UV Raman spectroscopy methods, showed a strong dependence of the results on the presence, on...
-
Flexural behaviour of concrete slabs reinforced with FRP bars in experiments and according to aci ACI 440.1R guide
PublikacjaThe paper presents research conducted on two concrete slabs reinforced with the carbon composite bars and two other concrete slabs reinforced with basalt composite bars. The carbon bars were plain, while the basalt ones were ribbed. The slabs were experimentally investigated in the flexural state of effort with the concentrated forces applied. The results are compared with the analytical solution proposed in the guide ACI 440.1R-06...
-
Practical Approach to IP Scheduled Throughput Measurements in Dual Connectivity Systems
PublikacjaIP scheduled throughput defined according to 3GPP TS 36.314 reflects user throughput regardless of traffic characteristics, and therefore has become one of the most important indicators for monitoring Quality of Service (QoS) of the end user in Evolved Universal Terrestrial Radio Access Network (E-UTRAN). However, networks built on a distributed architecture make the above definition impossible to be applied directly due to the...
-
OPTIMIZATION OF THE LAST STAGE OF GAS-STEAM TURBINE USING A HYBRID METHOD
PublikacjaThis paper relates to the CFD calculation of a new turbine type which is in the phase of theoretical analysis, because the working fluid is a mixture of steam and gas generated in wet combustion chamber. At first, this article concentrates on a possibility of streamlining the flow efficiency of a last stage of axial turbine working on gas-steam mixture using a hybrid of the particle swarm optimization algorithm with the Nelder-Mead...
-
Positron collisions with molecular hydrogen: cross sections and annihilation parameters calculated using theR-matrix with pseudo-states method
PublikacjaThe molecular R-matrix with pseudo-states (MRMPS) method is employed to study positron collisions with H2. The calculations employ pseudo-continuum orbital sets containing up to h (l = 5) functions. Use of these high l functions is found to give converged eigenphase sums. Below the positronium formation threshold, the calculated cross sections agree with other high-accuracy theories and generally with the measurements. Calculation...
-
Design of compound curves adapted to the satellite measurements
PublikacjaThe paper deals with a novelty related to the design of a region for an alternative railway track direction adequate for mobile satellite measurements. The new approach may become particularly useful in the design of the existing track axis control when the determination of both the main track directions becomes impossible. The only solution in that case is to apply to the geometrical system two circular arcs of a different radius,...
-
The performance of ETFs on developed and emerging markets with consideration of regional diversity
PublikacjaThis study evaluates the performance of Exchange-Traded Funds (ETFs) by using various tracking error calculation approaches. The aim of the paper is, on the one hand, an evaluation of the performance of ETFs relative to their benchmarking indexes and, on the other, an endeavour to specify any relationship between this performance and both geographical location and the degree of market development. The research was conducted on...
-
CONCRETE MIX DESIGN USING ABRAMS AND BOLOMEY METHODS
PublikacjaOne way to reduce the consumption of cement is to optimize its use. Many known methods of concrete design, based on the Abrams law and the Bolomey method. Therefore, the authors chose those methods for analysis. The concrete composition with the assumed strength class, calculated by any method differs significantly. This applies especially to the cement content, as its content in the composition of concrete varies from 20 to 50%....
-
Numerical investigation of the core eccentricity effect on wave propagation in embedded waveguide
PublikacjaThe paper presents results of theoretical and numerical investigation of guided wave propagation in two-layer bars with geometric imperfections in the form of eccentric location of steel core. Steel rod of diameter equal to 1 cm embedded in composite mortar-type cover with external diameter equal to 5 cm has been taken into consideration. Several different rods with variable size of eccentricity are analysed. Results for rods with...
-
Implementation of high-precision computation capabilities into the open-source dynamic simulation framework YADE
PublikacjaThis paper deals with the implementation of arbitrary precision calculations into the open-source discrete element framework YADE published under the GPL-2+ free software license. This new capability paves the way for the simulation framework to be used in many new fields such as quantum mechanics. The implementation details and associated gains in the accuracy of the results are discussed. Besides the "standard" double (64 bits)...
-
Application of Barycentric Coordinates in Space Vector PWM Computations
PublikacjaThis paper proposes the use of barycentric coordinates in the development and implementationof space-vector pulse-width modulation (SVPWM) methods, especially for inverters with deformed space-vector diagrams. The proposed approach is capable of explicit calculation of vector duty cycles, independentof whether they assume ideal positions or are displaced due to the DC-link voltage imbalance. The use ofbarycentric coordinates also...
-
A nine-input 1.25 mW, 34 ns CMOS analog median filter for image processing in real time
PublikacjaIn this paper an analog voltage-mode median filter, which operates on a 3 × 3 kernel is presented. The filter is implemented in a 0.35 μm CMOS technology. The proposed solution is based on voltage comparators and a bubble sort configuration. As a result, a fast (34 ns) time response with low power consumption (1.25 mW for 3.3 V) is achieved. The key advantage of the configuration is relatively high accuracy of signal processing,...
-
Termination functions for evolutionary path planning algorithm
PublikacjaIn this paper a study of termination functions (stop criterion) for evolutionary path planning algorithm is presented. Tested algorithm is used to determine close to optimal ship paths in collision avoidance situation. For this purpose a path planning problem is defined. A specific structure of the individual path and fitness function is presented. For the simulation purposes a close to real tested environment is created. Five...
-
Asynchronous Wide Area Multilateration System
PublikacjaA new method for a location service in the wide area multilateration (WAM) system is outlined. This method, which is called asynchronous WAM (AWAM), enables calculation of the geographical position of an aircraft without knowledge of relative time differences (RTDs) between measuring ground stations (sensors). The AWAM method is based on the measurement of round trip times (RTTs) between the aircraft and the serving ground station,...
-
Sensorless IPMSM drive with rotor position estimator based on analysis of phase current derivatives
PublikacjaThis paper describes a sensorless Interior Permanent Magnet Synchronous Motor (IPMSM) drive designed for traction applications. Wide-speed sensorless operation is provided with the use of three methods of rotor position estimation designed for: a standstill, low- and high-speed range. The paper focuses on the high-speed estimation algorithm. The estimator uses the derivatives of motor phase currentsresulting from PWM modulation...
-
Comparison of various speech time-scale modificartion methods
PublikacjaThe objective of this work is to investigate the influence of the different time-scale modification (TSM) methods on the quality of the speech stretched up using the designed non-uniform real-time speech time-scale modification algorithm (NU-RTSM). The algorithm provides a combination of the typical TSM algorithm with the vowels, consonants, stutter, transients and silence detectors. Based on the information about the content and...
-
Creating Acoustic Maps Employing Supercomputing Cluster
PublikacjaThe implemented online urban noise pollution monitoring system is presented with regard to its conceptual assumptions and technical realization. A concept of the noise source parameters dynamic assessment is introduced. The idea of noise modeling, based on noise emission characteristics and emission simulations, was developer and practically utilized in the system. Furthermore, the working system architecture and the data acquisition...
-
The analytical design method of railway route’s main directions intersection area
PublikacjaThe paper presents a design method related to railway track sections situated in a bend. In the method advantage is taken of an analytical form of description by using appropriate mathematical formulae. This may becomeparticularly usefulwhen the investigations are based on the data obtained from mobile satellite measurements. In the paper attention is concentrated on an universal approach creating an opportunity to diversify the...
-
Simplified stability analysis of steel cylindrical silos with corrugated walls and vertical columns
PublikacjaIn the paper a simplified stability analysis of steel cylindrical silos composed of corru¬gated walls and vertical open-sectional columns was proposed. The whole 3D silo was modeled as a single column resting on elastic foundation provided by the silo walls. In proposed formula for the calculation of the foundation stiffness the curvature of the silo walls was taken into account. Three different analyses were carried out using...