Wyniki wyszukiwania dla: FAULT SYMPTOMS SENSITIVITY ANALYSIS
-
Improving sensitivity of residual current transformers to high frequency earth fault currents
PublikacjaFor protection against electric shock in low voltage systems residual current devices are commonly used. However, their proper operation can be interfered when high frequency earth fault current occurs. Serious hazard of electrocution exists then. In order to detect such a current, it is necessary to modify parameters of residual current devices, especially the operating point of their current transformer. The authors proposed...
-
Testing sensitivity of A-type residual current devices to earth fault currents with harmonics
PublikacjaIn many applications, modern current-using equipment utilizes power electronic converters to control the consumed power and to adjust the motor speed. Such equipment is used both in industrial and domestic installations. A characteristic feature of the converters is producing distorted earth fault currents, which contain a wide spectrum of harmonics, including high-order harmonics. Nowadays, protection against electric shock in...
-
State and control system variables sensitivity to rotor asymmetry in the induction motor drive
PublikacjaThe aim of this paper is to undertake analysis and comparison of the closed-loop and sensorless control systems sensitivity to the broken rotor for diagnostic purposes. For the same vector control system induction motor drive analysis concerning operation with the asymmetric motor, broken rotor fault handling and operation were investigated. Reliability, range of stable operation, fault symptoms and application of diagnosis methods...
-
Fault Diagnostics in PEMFC Stacks by Evaluation of Local Performance and Cell Impedance Analysis
PublikacjaStarvation, flooding, and dry‐out phenomena occur in polymer electrolyte membrane fuel cells (PEMFCs), due to heterogeneous local conditions, material inhomogeneity, and uneven flow distribution across the single cell active area and in between the individual cells. The impact of the load level and air feed conditions on the performance was identified for individual single cells within a 10‐cell stack. Analysis of the current density...
-
Fast Real-Time RDFT- and GDFT-Based Direct Fault Diagnosis of Induction Motor Drive
PublikacjaThis paper presents the theoretical analysis and experimental verification of a direct fault harmonic identification approach in a converter-fed electric drive for automated diagnosis purposes. On the basis of the analytical model of the proposed real-time direct fault diagnosis, the fault-related harmonic component is calculated using recursive DFT (RDFT) and Goertzel DFT (GDFT), applied instead of the full spectrum calculations...
-
Broken Rotor Symptons in the Sensorless Control of Induction Machine
PublikacjaInverter fed sensorless controlled variable speed drives with induction machine are widely used in the industry applications, also in wind power generation and electric vehicles. On-line self diagnostic systems implementation is needed for early stage fault detection and avoiding a critical fault. Diagnostic algorithms in modern DSP-based controllers can operate simultaneously with control system functions. In the closed-loop controlled...
-
SELECTION OF DIAGNOSTIC FUNCTIONS IN A WHEELED TRACTOR
PublikacjaIn a classical approach to damage diagnosis, the technical condition of an analyzed machine is identified based on the measured symptoms, such as performance, thermal state or vibration parameters. In wheeled tractor the fundamental importance has monitoring and diagnostics during exploitation concerning technical inspection and fault element localizations. The main functions of a diagnostic system are: monitoring tractor components...
-
Behavior of residual current devices at earth fault currents with DC component
PublikacjaLow-voltage electrical installations are increasingly saturated with power electronic converters. Due to very high popularity of photovoltaic (PV) installations and the spread of electric vehicles (EV) as well as their charging installations, DC–AC and AC–DC converters are often found in power systems. The transformerless coupling of AC and DC systems via power electronic converters means that an electrical installation containing...
-
Broken rotor bar impact on sensorless control of induction machine
PublikacjaThe aim of the research is analysis of the sensorless control system of induction machine with broken rotor for diagnostic purposes. Increasing popularity of sensorless controlled variable speed drives requires research in area of reliability, range of stable operation, fault symptoms and application of diagnosis methods. T transformation (Cunha et al.,2003) used for conversion of instantaneous rotor currents electrical circuit...
-
Identification of diagnostic parameter sensitivity during dynamic processes of a marine engine
PublikacjaChanging some parameters of the engine structure alters the emission of harmful components in the exhaust gas. This applies in particular to the damage of charge exchange system as well as fuel system and engine supercharger. These changes are much greater during the dynamic states and their accompanying transitional processes. The different sensitivity of diagnostic parameters to the same force, coming from the engine structure, but...
-
THE IDENTIFICATION OF TOXIC COMPOUND EMISSION SENSITIVITY AS A DIAGNOSTIC PARAMETER DURING DYNAMIC PROCESSES OF THE MARINE ENGINE
PublikacjaChanging some parameters of the engine structure alters the emission of harmful components in the exhaust gas. This applies in particular to the damage of charge exchange system as well as fuel system and engine supercharger. These changes are much greater during the dynamic states and their accompanying transitional processes. The different sensitivity of diagnostic parameters to the same force, coming from the engine structure,...
-
CREATING A RANKING OF DIAGNOSTIC PARAMETERS FOR THE DYNAMIC PROCESS OF A MARINE COMBUSTION ENGINE IN THE ASPECT OF MULTI-CRITERIA EVALUATIONS
PublikacjaThe change of some of the engine’s structural parameters affects the change of toxic compound emission in exhaust gases. It mainly applies to the damage sustained by the charge exchange system as well as the fuel system and the engine supercharging system. These changes are definitely higher during dynamic states and the related transient states. As such, it is possible to speak of a diverse sensitivity of the diagnostic parameters...
-
Stability Enhancement of Grid-Connected Wind Power Generation System Using PSS, SFCL and STATCOM
PublikacjaThe stability related issues may occur in a power system due to disturbances in generating or loading conditions, especially in the presence of distributed generation (DG) based on renewable energy resources (RERs). This paper proposes a novel strategy for the stability enhancement of a wind power generation system (WPGS) by using a combination of three devices, namely, a power system stabilizer (PSS), resistive superconductor...
-
Blood concentrations of a new psychoactive substance 4-chloromethcathinone (4-CMC) determined in 15 forensic cases
PublikacjaPurpose: The 4-chloromethcathinone (4-CMC) is a synthetic derivative of cathinone and belongs to new psychoactive substances. Neither data on the effects of 4-CMC on the human body, nor on nontoxic, toxic and lethal concentrations in biological materials have been published in the literature. This paper describes the results of an analysis of the blood concentrations of 4-CMC determined in 15 forensic cases related to nonfatal...
-
Diagnostic system of wheeled tractors detecting four defect's categories
PublikacjaIn a classical approach to damage diagnosis, the technical condition of an analyzed machine is identified based on the measured symptoms, such as performance, thermal state or vibration parameters. In wheeled tractor the fundamental importance has monitoring and diagnostics during exploitation concerning technical inspection and fault element localizations. The main functions of a diagnostic system are: monitoring tractor components...
-
An annotated timeline of sensitivity analysis
PublikacjaThe last half a century has seen spectacular progresses in computing and modelling in a variety of fields, applications, and methodologies. Over the same period, a cross-disciplinary field known as sensitivity analysis has been making its first steps, evolving from the design of experiments for laboratory or field studies, also called ‘in-vivo’, to the so-called experiments ‘in-silico’. Some disciplines were quick to realize the...
-
Sensitivity analysis of a composite footbridge
PublikacjaThis work include an example of sensitivity analysis for the design of a composite footbridge. A sandwich structure is used, consisting two high-strength skins separated by a core material. The analysis was conducted for two numerical models. The first one is a simple, single-span beam of a composite cross-section (laminate and foam), with different Young’s modulus for each material. Calculations were made by means of a MATLAB-based...
-
Opitmalising Human Development Index with sensitivity analysis
PublikacjaResearch background: Composite indicators are commonly used not only to measure economic development, the standard of livin g, competitiveness, fairness, effectiveness but are also willingly implemented in to many different fields. How- ever, it seems that in most cases the variable weig hting procedure is avoided or erroneous since in most cases so-called “wights by belief” are...
-
Sensitivity analysis of critical forces of trusses with side bracing
PublikacjaThe present research is devoted to the study of out-of-plane buckling of trusses with elastic side bracing. Inthis paper, a sensitivity analysis of critical buckling loads of a truss due to bracing stiffness is carried out. A method based on the sensitivity analysis for the determination of the threshold bracing stiffness conditionfor full bracing of a truss is proposed. The influence lines of the unit change of the bracing stiffness...
-
Sensitivity analysis in design process of sandwich U-shaped composite footbridge
PublikacjaThe structure of the sandwich composite footbridge of a 14 metre span length and U-shaped cross-section was analysed. Sensitivity analysis was performed to support the design process of this innovative object. Linear discrete sensitivity analysis was performed by means of finite element method. The influence of vari-ation of several design variables i.e. thicknesses of inner and outer laminates on the mid-span deflection, as-sumed...
-
Sensitivity analysis of flexural and torsional buckling loads of laminated columns
PublikacjaThe paper concerns first order sensitivity analysis of flexural and torsional bucklin g loads of axiallycompressed thin-walled columns with bisymmetric or axisymmetric cross-section made of unidirectional fibre-reinforcedlaminate. The first variation of critical loads versus some variations of the column material properties and cross-sectionaldimensions is derived. Numerical examples dealing with simply supported I-columns are...
-
Sensitivity analysis as a tool to optimise Human Development Index
PublikacjaResearch background: Composite indicators are commonly used as an approximation tool to measure economic development, the standard of living, competitiveness, fairness, effectiveness, and many others being willingly implemented into many different research disciplines. However, it seems that in most cases, the variable weighting procedure is avoided or erroneous since, in most cases, the so-called...
-
Structural Design and Sensitivity Analysis of Semi-Rigid Pavement of a Motorway
PublikacjaThis paper presents application of mechanistic-empirical methods in design of semi-rigid pavement for a section of a motorway in Poland. The stage construction was assumed. Three fatigue criteria were applied in the design. For asphalt fatigue cracking and subgrade soil the criteria from the Asphalt Institute (1981) were applied. For fatigue cracking of cement stabilized bases the Dempsey (1984) and De Beer (1992) criteria were...
-
Fault diagnosing system of wheeled tractors
PublikacjaA defect of complex wheeled tractor assembles most frequently negative influence on exploitation efficiency, safety and exhaust gases emission. Structure complexity of wheeled tractors requires more and more advanced diagnostic methods for identification of their serviceable possibilities as well in manufacturing step as in exploitation. In classical diagnosing methods of wheeled tractor defects states mapping by measured diagnostic...
-
Iterative Global Sensitivity Analysis Algorithm with Neural Network Surrogate Modeling
PublikacjaGlobal sensitivity analysis (GSA) is a method to quantify the effect of the input parameters on outputs of physics-based systems. Performing GSA can be challenging due to the combined effect of the high computational cost of each individual physics-based model, a large number of input parameters, and the need to perform repetitive model evaluations. To reduce this cost, neural networks (NNs) are used to replace the expensive physics-based...
-
Neural Network-Based Sequential Global Sensitivity Analysis Algorithm
PublikacjaPerforming global sensitivity analysis (GSA) can be challenging due to the combined effect of the high computational cost, but it is also essential for engineering decision making. To reduce this cost, surrogate modeling such as neural networks (NNs) are used to replace the expensive simulation model in the GSA process, which introduces the additional challenge of finding the minimum number of training data samples required to...
-
Global sensitivity analysis of membrane model of abdominal wall with surgical mesh
PublikacjaThe paper addresses the issue of ventral hernia repair. Finite Element simulations can be helpful in the optimization of hernia parameters. A membrane abdominal wall model is proposed in two variants: a healthy one and including hernia defect repaired by implant. The models include many uncertainties, e.g. due to variability of abdominal wall, intraabdominal pressure value etc. Measuring mechanical properties with high accuracy...
-
An advanced tool integrating failure and sensitivity analysis into novel modeling of the stormwater flood volume
PublikacjaAn innovative tool for modeling the specific flood volume was presented that can be applied to assess the need for stormwater network modernization as well as for advanced flood risk assessment. Field measurements for a catchment area in Kielce, Poland, were used to apply the model and demonstrate its usefulness. This model extends the capability of recently developed statistical and machine learning hydrodynamic models developed...
-
Advanced sensitivity analysis of the impact of the temporal distribution and intensity of rainfall on hydrograph parameters in urban catchments
PublikacjaKnowledge of the variability of the hydrograph of outflow from urban catchments is highly important for measurements and evaluation of the operation of sewer networks. Currently, hydrodynamic models are most frequently used for hydrograph modeling. Since a large number of their parameters have to be identified, there may be problems at the calibration stage. Hence, sensitivity analysis is used to limit the number of parameters....
-
SENSITIVITY ANALYSIS IN THE REHABILITATION OF HISTORIC TIMBER STRUCTURES ON THE EXAMPLES OF GREEK CATHOLIC CHURCHES IN POLISH SUBCARPATHIA
PublikacjaThis work concerns structural and sensitivity analysis of carpentry joints used in historic wooden buildings in south-eastern Poland and western Ukraine. These are primarily sacred buildings and the types of joints characteristic for this region are saddle notch and dovetail joints. Thus, in the study the authors focus on these types of corner log joints. Numerical models of the joints are defined and finite element simulations...
-
Multiparameter sensitivity analysis of a GFRP composite footbridge of a sandwich structure and U-shaped cross-section
PublikacjaThe paper deals with multiparameter sensitivity analysis of a composite footbridge. A shell‐like structure is 14.5 m long shows U‐shaped cross‐section and inner service dimensions 1.3 × 2.5 m. Glass fiber reinforced polymer GFRP laminate constitutes faces of a sandwich structure while PET foam received from recycled bottle builts a core. The structure was divided into 285 independent areas where the thickness of laminates and stiffness...
-
Sensitivity analysis of free torsional vibration frequencies of thin-walled laminated beams under axial load
PublikacjaThe paper addresses sensitivity analysis of free torsional vibration frequencies of thin-walled beams of bisymmetric open cross-section made of unidirectional fibre-reinforced laminate. The warping effect and the axial end load are taken into account. The consideration is based upon the classical theory of thin-walled beams of non-deformable cross-section. The first-order sensitivity variation of the frequencies is derived with...
-
Basic sensitivity analysis of a telecommunication tower complementing standard reinforcement design process
PublikacjaThis paper presents straightforward sensitivity assessment of a telecommunication tower. The analysis is set toidentify the elements of the tower which may be reinforced with the greatest structural advantage. As current expertopin ions on structural redesign of similar structures due to a planned addition of extra loads are mainly based ondeterministic computations or engineering intuition,...
-
Sensitivity analysis of simple random beam models by means of Monte Carlo Methods using Variance Reductions Techniques
PublikacjaA probabilistic sensitivity analysis of two nonlinear bar structures is presented. The analysis is carried out on the basis of the Monte Carlo method. The imperfections of the structures and the applied loads are adapted as random variables. Based on all of the generated input variables, an output response of the system is sought. Afterwards, a coefficient responsible for the structure failure is calculated and the limit state...
-
Sensitivity analysis of critical loads of I-columns
PublikacjaThe first order variation of critical buckling load of thin-walled columns with bisymmetric open cross-section due to some variations of the design variables such as: cross-section dimensions, or material characteristics is derived. The influence of the residual welding stresses is taken into account. In the numerical examples dealing with I-column the functions describing the effect of the variation of the dimensions of the flange...
-
Sensitivity analysis of thin-walled beams and frames.
PublikacjaPraca zawiera pełen tekst referatu wygloszonego na Konferencji w Wilnie.Referat przedstawia problem numerycznej analizy wrażliwości belek i ramstalowych zbudowanych z bi-symetrycznych profili cienkościennychpoddanych skręceniu lub skręceniu ze zginaniem. Przedstawiono wynikianalizy wrażliwości przemieszczeń i sił wewnętrznych przy zmianiegrubosci półek, sztywności dodatkowych stężeń poprzecznych orazszerokości przewiązek.
-
Sensitivity analysis based on non-intrusive regression-based polynomial chaos expansion for surgical mesh modelling
PublikacjaThe modelling of a system containing implants used in ventral hernia repair and human tissue suffers from many uncertainties. Thus, a probabilistic approach is needed. The goal of this study is to define an efficient numerical method to solve non-linear biomechanical models supporting the surgeon in decisions about ventral hernia repair. The model parameters are subject to substantial variability owing to, e.g., abdominal wall...
-
Sensitivity analysis of thin-walled members, problems and applications
PublikacjaPodano przegląd problemów analizy wrażliwości konstrukcji cienkościennych. Przedstawiono metody określania pierwszej wariacji zmiennych stanu takich jak: przemieszczenia, siły wewnętrzne, reakcje, częstości i postaci drgań własnych oraz obciążeń krytycznych ze względu na zmiany parametrów konstrukcji. Rozważania ograniczono do prętów cienkościennych o otwartym bisymetrycznym przekroju poprzecznym w ramach założeń teorii prętów...
-
Analysis of pavement structure sensitivity to passage of oversized heavy duty vehicle in terms of bearing capacity
PublikacjaOversized heavy duty vehicles occur in traffic very rarely but they reach extremely high weights, even up to 800 tonne. The detrimental impact of these vehicles on pavement structure is much higher than in case of commercial vehicles that comprise typical traffic, thus it is necessary to assess the sensitivity of pavement structure to passage of oversized vehicles. The paper presents results of sample calculations of load equivalency factor...
-
SDGs implementation, their synergies, and trade-offs in EU countries – Sensitivity analysis-based approach
PublikacjaSustainable development is one of the most urgent challenges facing humanity. Its basic principle is to improve people’s well-being and maintain it over time. In 2015, the United Nations approved 17 sustainable development goals (SDGs) to ensure a better and sustainable future for all, balancing economic, social and environmental development. SDGs create an ‘indivisible whole’; thus, examining their interactions is crucial. Our...
-
Structural design and sensitivity analysis of semi-rigid pavement of a motorway
PublikacjaThis paper presents application of mechanistic-empirical methods in design of semi-rigid pavement for a section of a motorway in Poland. The stage construction was assumed. Three fatigue criteria were applied in the design. For asphalt fatigue cracking and subgrade soil the criteria from the Asphalt Institute (USA) were applied. For fatigue cracking of cement stabilized bases the Dempsey (USA) and De Beer (South Africa) criteria...
-
Sensitivity analysis of beams and frames made of thin-walled members
PublikacjaMonografia dotyczy analizy wrażliwości w problemach statyki układów zbudowanych z prętów cienkościennych. Przedstawiono w niej nowe podejście do modelowania belek i ram z różnego rodzaju stężeniami ograniczającymi spaczenie przekroju poprzecznego, w przypadku skręcenia. Wprowadzono pojęcie superelementu belkowego i węzłowego. Przeprowadzono analizę statyczną belek i ram poddanych skręceniu lub skręceniu ze zginaniem, wzmocnionych...
-
Free torsional vibration sensitivity analysis of thin walled beams.
PublikacjaW pracy przedstawiono analizę wrażliwości swobodnych drgań skrętnych bisymetrycznej , cienkościennej belki o otwartym przekroju poprzecznym, poddanej działaniu siły osiowej
-
Adjoint approach sensitivity analysis of thin-walled beams and frames.
PublikacjaArtykuł omawia zastosowanie metody układów sprzężonych w numerycznej analizie wrażliwości belek i ram zbudowanych ze stalowych profili cienkościennych poddanych skręceniu lub skręceniu ze zginaniem. Przedstawiono wyniki analizy wrażliwości przemieszczeń i sił wewnętrznych na zmianę parametrów geometrycznych konstrukcji.
-
Static and sensitivity analysis of thin-walled beams and frames with stiffeners.
PublikacjaPraca zawiera tekst referatu wygłoszonego w Maastricht. Przedstawiono analizę statyczną oraz analizę wrażliwości belek i ram zbudowanych z cienkościennych elementów, poddanych skręcaniu lub zginaniu ze skręcaniem, z możliwością zastosowania różnego typu stężeń . Wykorzystano technikę superelementu do wyznaczenia macierzy sztywności węzła ramy i elementów ze stężeniami. Otrzymane wyniki dla modelu jednowymiarowego MES porównano...
-
Application of linear buckling sensitivity analysis to economic design of cylindrical steel silos composed of corrugated sheets and columns
PublikacjaThe paper deals with global stability of steel cylindrical silos composed of corrugated walls and vertical columns with loads imposed by a bulk solid following Eurocode 1. The optimum silo design with respect to the steel weight was based on a sensitivity analysis method. The changes of silo column profiles at each design step were performed by means of influence lines for the buckling load factor due to the unit column bending...
-
Sensitivity analysis of the contractor’s financial effects achieved on a single building site
Publikacja -
Electrodes array for contactless ECG measurement of a bathing person - a sensitivity analysis
PublikacjaAn applicability of a remote (contactless) electrocardiogram (ECG) measurements in a bathtub is presented in the paper. Possibility of ECG measurements in shallowly filled tube with a water was examined. A bathing person was, both, sitting and lying during experiments performed. The problem became non-trivial when the bathing person was moving in reference to a fixed set of electrodes and located at the longer walls of the bathtub....
-
Fault Tree Analysis and Failure Diagnosis of Marine Diesel Engine Turbocharger System
Publikacja -
Sensitivity analysis of buckling loads of bisymmetric I-section columns with bracing elements
PublikacjaWyznaczono pierwsza wariacje siły krytycznej wyboczenia słupa o przekroju bisymetrycznym otwartym przy wariacji sztywnosci i połozenia stezen. Przyjeto załozenia klasycznej teorii pretów cienkosciennych o nieodkształcalnym przekroju poprzecznym. Analizowano zarówno stezenia boczne jak i stezenia ograniczajacespaczenie oraz skrecenie przekroju poprzecznego. Stezenia modelowano jako podpory sprezyste. W przykładzie numerycznym zbadano...
-
Condition monitoring and fault detection in wind turbines based on cointegration analysis of SCADA data
Publikacja -
On Cointegration Analysis for Condition Monitoring and Fault Detection of Wind Turbines Using SCADA Data
Publikacja -
Sensitivity, Specificity and Prioritization of Gene Set Analysis When Applying Different Ranking Metrics
Publikacja -
Integrated model for the fast assessment of flood volume: Modelling – management, uncertainty and sensitivity analysis
PublikacjaThe specific flood volume is an important criterion for assessing the performance of sewage networks. It has been shown that its value is greatly influenced by the layout of the sewers in the catchment area, which is usually expressed by a fractal dimension. Currently, only mechanistic models (such as SWMM) enable the determination of the impact of the layout of the sewers on flooding volume, but they require additional and robust...
-
Tomasz Mikulski dr hab. inż.
Osoby -
Modeling of the fascia-mesh system and sensitivity analysis of a junction force after a laparoscopic ventral hernia repair
PublikacjaW pracy rozpatrywano prosty model cięgnowy układu powięż-siatka do oszacowania siły połączenia siatki z powięzią po operacji laparoskopowej przepukliny brzusznej. Cięgno obciążone jest ciśnieniem wewnątrz brzusznym, symulującym kaszel, oraz przemieszczeniami jego końców wywołanymi skłonami pacjenta. Wpływ poszczególnych parametrów cięgna na siłę połączenia określono za pomocą analizy wrażliwości. Sformułowano pewne wnioski ważne...
-
Failure of cylindrical steel silos composed of corrugated sheets and columns and repair methods using a sensitivity analysis
PublikacjaW artykule omówiono przypadek awarii metalowego silosu z blachy walcowej i pionowych słupów. Wykonano analizę wyboczeniową MES z uwzględnieniem imperfekcji geometrycznych. Omówiono metody naprawcze i ich optymalizację w oparciu o analizę wrażliwości.
-
Simulation of static response of thin walled bars with changed design parameters by means of second order sensitivity analysis.
PublikacjaZa pomocą analizy wrażliwości drugiego rzędu wyznaczono przybliżone wartości sił wewnętrznych i przemieszczeń pręta cienkościennego dla zmieniających się parametrów projektowych. W przykładzie numerycznym wyznaczono pierwszą i drugą wariację bimomentu w funkcji grubości półek skręcanego dwuteownika. Zbadano dokładność rozwiązania uzyskanego za pomocą analizy wrażliwości z rozwiązaniem ścisłym.
-
Pneumonia, gastrointestinal symptoms, comorbidities, and coinfections as factors related to a lengthier hospital stay in children with COVID-19—analysis of a paediatric part of Polish register SARSTer
Publikacja -
Ireneusz Kreja dr hab. inż.
OsobyAbsolwent klasy matematycznej I Liceum Ogólnokształcącego w Gdańsku im. Mikołaja Kopernika (1974). Absolwent Wydziału Budownictwa Lądowego Politechniki Gdańskiej (1979). Od 1979 pracuje na PG. W 1989 uzyskał doktorat (z wyróżnieniem), na Wydziale Budownictwa Lądowego, a w 2008 habilitował się (również z wyróżnieniem) na Wydziale Inżynierii Lądowej i Środowiska PG. Od 2011 jest profesorem PG. Na Politechnice Gdańskiej pełnił funkcje:...
-
Open-Phase Fault Detection Method for Sensorless Five-Phase Induction Motor Drives with an Inverter Output Filter
PublikacjaThe paper presents the sensorless five-phase induction motor drive implementation with an inverter output filter with third harmonic injection. For the sensorless operation, the required observers are presented for the first and third harmonics with consideration of the inverter output filter. Moreover, the interaction of the observers and the control system is capable to handle a deactivation of one or two phases, which improves...
-
Mechanical Strength of MV Ship-switchgear During Fault Arc
PublikacjaIn the paper the analysis of pressure stressed in enclosure during fault arc inside switchgear is pre-sented as well. There is introduced the method based on determining stresses which are sum of tensile stresses (membrane) and deflection stresses. For tensile stresses nalysis the energy method, for unrestrainedly supported rectangular plate, was used. In the further part of the paper, the calculations and measurements results...
-
AN ALGORITHM FOR PORTAL HYPERTENSIVE GASTROPATHY RECOGNITION ON THE ENDOSCOPIC RECORDINGS
PublikacjaSymptoms recognition of portal hypertensive gastropathy (PHG) can be done by analysing endoscopic recordings, but manual analysis done by physician may take a long time. This increases probability of missing some symptoms and automated methods may be applied to prevent that. In this paper a novel hybrid algorithm for recognition of early stage of portal hypertensive gastropathy is proposed. First image preprocessing is described....
-
Analog fault signature based on sigma-delta modulation and oscillation-test methodology.
PublikacjaW artykule dokonano przeglądu prac z zakresu testowania układów elektronicznych metodą oscylacyjną. Wskazując na niedostatki aktualnie stosowanej techniki testowania oscylacyjnego zaproponowano nową sygnaturę uszkodzeń dla układów analogowych. Proponowany parametr diagnostyczny jest wydobywany z odpowiedzi czasowej oscylatora testującego, w układzie złożonym z detektora szczytowego, modulatora sigma-delta oraz licznika rewersyjnego....
-
The Polish adaptation of the Burnout Assessment Tool (BAT-PL) by W. Schaufeli et al.
PublikacjaAim. The study aimed to present the Polish version of the Burnout Assessment Tool (BAT-PL) by Schaufeli et al. and to assess its validity and reliability. The tool measures the core symptoms of burnout (BAT-C): exhaustion, mental distance, cognitive and emotional impairment, and its secondary symptoms (BAT-S): psychosomatic complaints and psychological distress. Method. The participants were 255 nursing staff members. The construct...
-
Wiktoria Wojnicz dr hab. inż.
OsobyDSc in Mechanics (in the field of Biomechanics) - Lodz Univeristy of Technology, 2019 PhD in Mechanics (in the field of Biomechanics) - Lodz Univeristy of Technology, 2009 (with distinction) Publikacje z listy MNiSW (2009 - ) Wojnicz W., Wittbrodt E., Analysis of muscles' behaviour. Part I. The computational model of muscle. Acta of Bioengineering and Biomechanics, Vol. 11, No.4, 2009, p. 15-21 Wojnicz W., Wittbrodt E., Analysis...
-
Wybrane metody przydatne w analizie niezawodności i bezpieczeństwa funkcjonalnego systemów technicznych.
PublikacjaPrzedstawiono wybrane metody przydatne w analizie niezawodności i bezpieczeństwa funkcjonalnego systemów technicznych takie jak: metoda FMECA (failure mode, effect and criticality analysis, FTA (fault tree analysis, RBD (reliability block diagram) RCM (reliability centered maintenance, LCC (life cycle cost) i PMO (preventive maintenance optimising.
-
Probabilistic Analysis of Structure Models using Target Random Sampling (TRS)
PublikacjaThe work presents testing methods of sensitivity and reliability of mechanical or structural systems. All computations concerned the case of Zigler column, a simple model of a compressed column involving two random variables only. A conclusion was drawn that the standard Monte Carlo method, its reduction variants and the response surface method allow to assess the sensitivity of structural response to the variation of random structural...
-
Projektowanie układów ramowych z zastosowaniem analizy wrażliwości
PublikacjaW pracy przedstawiono przykład projektowania układów ramowych z zastosowaniem analizy wrażliwości. Rozważane układy ramowe rozwiązano autorskim programem napisanym w środowisku MATLAB, metodą elementów skończonych. Badano wpływ zmiany modułu Younga oraz wpływ zmiany wielkości przekroju poprzecznego na wybrane przemieszczenia ramy. Przedstawiono wyniki dla analizy wrażliwości jedno i wieloparametrycznej.
-
Influence of Diosmin Treatment on the Level of Oxidative Stress Markers in Patients with Chronic Venous Insufficiency
PublikacjaOxidative stress plays an important role in the pathophysiology of many human disorders, while antioxidants prevent the development of various adverse symptoms. Diosmin is a natural flavonoid applied in vascular system disorders, especially in chronic venous insufficiency (CVI), and it plays a significant part in the alleviation of CVI symptoms. Due to antioxidant activity, it also has the ability to scavenge the oxygen free radicals...
-
Optimising approach to designing kernel PCA model for diagnosis purposes with and without a priori known data reflecting faulty states
PublikacjaFault detection plays an important role in advanced control of complex dynamic systems since precise information about system condition enables efficient control. Data driven methods of fault detection give the chance to monitor the plant state purely based on gathered measurements. However, they especially nonlinear, still suffer from a lack of efficient and effective learning methods. In this paper we propose the two stages learning...
-
Use of Neural Networks in Diagnostics of Rolling-Element Bearing of the Induction Motor
PublikacjaBearing defect is statistically the most frequent cause of an induction motor fault. The research described in the paper utilized the phenomenon of the current change in the induction motor with bearing defect. Methods based on the analysis of the supplying current are particularly useful when it is impossible to install diagnostic devices directly on the motor. The presented method of rolling-element bearing diagnostics used indirect...
-
Low-frequency tripping characteristics of residual current devices
PublikacjaFast development of various types of converters makes their utilization in industry and in domestic installations very common. Due to converters, an earth fault current waveform in modern circuits can be distorted or its frequency can be different than 50/60 Hz. Frequency of earth fault (residual) current influences tripping of residual current devices which are widely used in low voltage systems. This paper presents the behaviour...
-
Demonstrator testera wbudowanego BIST dla układów w pełni różnicowych
PublikacjaPrzedstawiono demonstrator testera wbudowanego, przeznaczony do pracy na stanowisku dydaktycznym w laboratorium z przedmiotu Zaawansowane Metody Pomiarowe i Diagnostyczne. Na stanowisku studenci zapoznają się z technologią BIST (ang. Built-In Self-Test), która jest przykładem wdrożenia strategii projektowania dla testowania.
-
Probabilistic sensitivity of limit states of structures. The Monte Carlo simulation
PublikacjaDesign sensitivity deals with the variation of structural response, implicitly dependent on the design variables of the problem. An attempt is made to implement probabilistic notation in engineering sensitivity analysis. The procedure to implement the sensitivity of a structural limit state to a given basic variable is described in the paper - its main idea, depicted by a flowchart and numerical examples of engineering analysis....
-
Kompozytowy most dla pieszych. Badania doświadczalne i przygotowanie do projektowania
PublikacjaDysertacja powstała w ramach grantu badawczego NCBiR, pt. „Opracowanie kompozytowych przęseł mostów dla pieszych do zastosowania nad drogami GP”, nr PBS1/B2/6/2013. Głównym celem pracy było wsparcie procesu projektowania kompozytowego mostu pieszo-rowerowego. Zakres pracy obejmuje badania doświadczalne elementów kompozytowych GFRP, walidację modeli obliczeniowych oraz wykorzystanie aparatu analizy wrażliwości do procesu projektowego....
-
PCA based Fault Tolerant MPC
PublikacjaThis chapter presents a Fault Tolerant - Model Predictive Control (FT-MPC) schemes for sensor faults accommodation. A Fault Detection and Isolation (FDI) Unit, which is an integral part of FT-MPC system, is based on the Principal Component Analysis (PCA) method. Introduced approach enables efficient bias and drift faults accommodation in single, as well as simultaneous faults case. Simple simulation exercise is presented.Rozdział...
-
Emotional distress, burnout and sense of safety during the COVID-19 pandemic in teachers after the reopening of schools
PublikacjaThe COVID-19 pandemic is having a significant impact on people's psychological well-being and mental health. This study aimed to identify factors linked to emotional distress, burnout and sense of safety in teachers related to the reopening of Polish schools after lockdown, remote work, and the holiday period between March and August 2020. A total of 1,286 teachers from different educational institutions participated in the...
-
Polska adaptacja Metody Oceny Wypalenia Zawodowego (BAT-PL) autorstwa Schaufeliego i współpracowników
PublikacjaAim. The study aimed to present the Polish version of the Burnout Assessment Tool (BAT-PL) by Schaufeli et al. and to assess its validity and reliability. The tool measures the core symptoms of burnout (BAT-C): exhaustion, mental distance, cognitive and emotional impairment, and its secondary symptoms (BAT-S): psychosomatic complaints and psychological distress. Method. The participants were 255 nursing staff members....
-
Optimal retrofit strategy using viscous dampers between adjacent RC and SMRFs prone to earthquake‑induced pounding
PublikacjaNowadays, retrofitting-damaged buildings is an important challenge for engineers. Finding the optimal placement of Viscous Dampers (VDs) between adjacent structures prone to earthquake-induced pounding can help designers to implement VDs with optimizing the cost of construction and achieving higher performance levels for both structures. In this research, the optimal placement of linear and nonlinear VDs between the 3-story, 5-story,...
-
Verification of safety in low-voltage power systems without nuisance tripping of residual current devices
PublikacjaLow-voltage power systems require initial and periodical verification to check the effectiveness of protection against electric shock. As a protection in case of fault, automatic disconnection of supply is most often used. To verify such a protection measure, the earth fault loop impedance or resistance is measured. This measurement is easy to perform in circuits without residual current devices. When residual current devices are...
-
Szybkie uziemniki do ograniczania skutków zwarć łukowych w okrętowych rozdzielnicach SN
PublikacjaW artykule scharakteryzowano moc i napięcie łuku, jak również przedstawiono model termodynamiczny służący do obliczania ciśnienia i temperatury gazów w otoczeniu łuku zwarciowego. Przedstawiono przykładowy układ elektrowni okrętowej i zasilania najważniejszych odbiorników na statku do przewozu gazu ziemnego w stanie ciekłym. Na podstawie parametrów prądnic i silników odbiorników zasilanych z rozdzielnicy głównej obliczono prądy...
-
Numerical Modelling of Structures with Uncertainties
PublikacjaThe nature of environmental interactions, as well as large dimensions and complex structure of marine offshore objects, make designing, building and operation of these objects a great challenge. This is the reason why a vast majority of investment cases of this type include structural analysis, performed using scaled laboratory models and complemented by extended computer simulations. The present paper focuses on FEM modelling...
-
Polyarmonic model of synchronous generator for analysis of autonomous power generation systems
PublikacjaAbstract: This paper presents the polyharmonic modelling of synchronous generator (SG) in machine variables. The simple geometry and windings physical layout has been used for inductance calculations of a salient-pole SG. The main advantage of this model is the ease of describing an autonomous power generation system (APGS) in terms of its topology and thus providing effective analysis at the static and dynamic states, both for...
-
Excavation induced cast iron pipeline failure – a numerical study
PublikacjaNumerical study on impact of an unsecured excavation on an underground pipeline. Analysis focused on investigation of pipeline displacement generated by soil movement caused by excavation and heavy traffic. Numerical calculations and soil parameter sensitivity analysis based on Finite Element Method. Some comparisons of results with real-life failure cases.
-
Selected problems of sensitivity and reliability of a jack-up platform
PublikacjaThe paper deals with sensitivity and reliability applications to numerical studies of an off-shore platform model. Structural parameters and sea conditions are referred to the Baltic jack-up drilling platform. The study aims at the influence of particular basic variables on static and dynamic response as well as the probability of failure due to water waves and wind loads. The paper presents the sensitivity approach to a generalized...
-
Design of novel highly sensitive sensors for crack detection in metal surfaces: theoretical foundation and experimental validation
PublikacjaThe application of different types of microwave resonators for sensing cracks in metallic structures has been subject of many studies. While most studies have been focused on improving the sensitivity of planar crack sensors, the theoretical foundation of the topic has not been treated in much detail. The major objective of this study is to perform an exhaustive study of the principles and theoretical foundations for crack sensing...
-
Modeling nutrient removal and energy consumption in an advanced activated sludge system under uncertainty
PublikacjaActivated sludge models are widely used to simulate, optimize and control performance of wastewater treatment plants (WWTP). For simulation of nutrient removal and energy consumption, kinetic parameters would need to be estimated, which requires an extensive measurement campaign. In this study, a novel methodology is proposed for modeling the performance and energy consumption of a biological nutrient removal activated sludge system...
-
Buckling of braced frames
PublikacjaIn this paper the classical Winter model, developed originally for columns is applied for frame structures and compared with the results of parametric study of frame with bracing. Sensitivity analysis of critical loads of frame due to bracing stiffness is carried out and the threshold bracing stiffness for full bracing is found. In the non-linear statical analysis the forces in bracings are calculated.
-
Data-driven models for fault detection using kernel pca:a water distribution system case study
PublikacjaKernel Principal Component Analysis (KPCA), an example of machine learning, can be considered a non-linear extension of the PCA method. While various applications of KPCA are known, this paper explores the possibility to use it for building a data-driven model of a non-linear system-the water distribution system of the Chojnice town (Poland). This model is utilised for fault detection with the emphasis on water leakage detection....
-
Mesh dependence study for numerical assessment of hydrodynamic characteristics of windsurfing fin
PublikacjaThe presented research aims to assess the drag coefficient and lift coefficient versus angle of attack curves for windsurfing fin. Special attention in the research was being paid to the evaluation of the stall angle value. The angle of incidence for which the stall occurs was searched, and the sensitivity of the solution for the mesh resolution was studied. The mesh resolution sensitivity analysis was done by systematically decreasing...
-
Redukcja czasu analizy MZP przez ograniczenie rozmiaru rozwiązania
PublikacjaAnaliza drzew niezdatności jest uznaną metodą analizy bezpieczeństwa systemów. Notacja ECSDM pozwala definiować zależności czasowe między zdarzeniami drzewa oraz przeanalizować je w celu określenia zależności pomiędzy zdarzeniami z Minimalnych Zbiorów Przyczyn (MZP). Dzięki wprowadzeniu klasyfikacji zdarzeń z MZP można wyodrębnić zależności czasowe istotne dla zapobiegania wywoływania hazardu przez konkretny MZP. Pozostałe zależności...
-
Management and economic of engineer projects
Kursy OnlineLectures - 05 October-30 November, 2023 1. Project management: Engineers, projects, management, planning and scheduling, personnel and organizational, team building, project control, estimating and ordering. 2. Team building: personality types, team effectiveness. 3. Project management: WBS, Gantt, Earned Value Method, critical path, risk management. 4. Economic Engineering: Establishing economic equivalence, Interest: cost...
-
Possibility of Fault Detection in Sensorless Electric Drives
PublikacjaThe work presents a fault detection method for an induction motor drive system with inverter output filter. This approach make use of a load torque state observer, which complete structure is presented along with the used control structure. Moreover, the demonstrated drive system operates without rotor speed measurement in conjunction with the multiscalar control. The verification of the demonstrated idea was performed on an experimental...
-
Determining and verifying the safety integrity level of the safety instrumented systems with the uncertainty and security aspects
PublikacjaSafety and security aspects consist of two different group of functional requirements for the control and protection systems. In the paper it is proposed that the security analysis results can be used as a factor increasing or decreasing the risk level. It concerns a process of determining required safety integrity level of given safety functions. The authors propose a new approach for functional safety risk analysis. In this case...
-
Earth wires currents calculation by tableau analysis
PublikacjaThe paper presents a new method to compute a phase-to-earth fault current distribution in overhead transmission line. The method is based on the tableau analysis of an unbalanced, multi-wire model of a transmission line. It allows for the calculation of current distribution in overhead earth wires along the transmission line. Additionally, it may be used to calculate currents in a tower’s earthing system as well as voltages over...
-
Advanced methods in biosensing: fundamentals and applications
Kursy OnlineThis course provides instruction in the basic science and engineering conceptsrequired to understand the design and application of biosensors. Different biosensorsystems are explored, ranging from electrochemical devices, through to optical orthermal systems. Instruction is also given in the general principles of sampling andanalysis, statistical presentation and manipulation of data. The primary focus will bethe physics of biomolecule...
-
Parametric optimization of sandwich composite footbridge with U-shaped cross-section
PublikacjaParametric optimization of sandwich composite footbridge was presented in the paper. Composite footbridge has 14,5 m long and has U-shaped cross-section with inner dimensions 2,6 × 1,3 m. The sandwich structure in made from GFRP laminate as a faces and PET foam as a core. The aim of analysis was to minimize the mass of the new footbridge that can lead to minimize the cost of structure. After optimization was conducted, the new...
-
Cross-domain applications of multimodal human-computer interfaces
PublikacjaDeveloped multimodal interfaces for education applications and for disabled people are presented, including interactive electronic whiteboard based on video image analysis, application for controlling computers with mouth gestures and audio interface for speech stretching for hearing impaired and stuttering people and intelligent pen allowing for diagnosing and ameliorating developmental dyslexia. The eye-gaze tracking system named...
-
The design of an intelligent medical space supporting automated patient interviewing
PublikacjaThe article presents the architecture and results of implementing an application for the intelligent medical space UbiDoDo (Ubiquitous Domestic Doctor's Office). The main purpose of the application is real-time monitoring of the biomedical parameters of a patient in his domestic environment. It allows an immediate reaction to appearing symptoms and provides means to automatically interview the patient and deliver his results to...