Wyszukiwarka
Filtry
wszystkich: 201
Wyniki wyszukiwania dla: TEST PROCEDURE
-
Influence of test procedure on surge impedance of lightning earthings.
PublikacjaUziemienia systemu ochrony odgromowej powinny być badane prądami o parametrach czasowych podobnych do rejestrowanych podczas wyładowań atmosferycznych.Podano definicję impedancji i warunki jej pomiaru. omówiono pojęcie długości efektywnej uziomu.
-
Multi-stage magnetic-fluid seals for operating in water - life test procedure, test stand and research results
PublikacjaThe edge criteria for magnetic-fluid seals durability research are critical for the seal'stechnological usefulness. The magnetic fluid seal technology in water is much moredifficult technological problem in comparison to gas or vacuum environment. There isalways problem with immediate contact between magnetic fluid and the environmentaluninspected liquids. In the paper are presented ways of experiments definitions carried outwith...
-
The New Test Procedure for Group-Type Composition of Base Oils of Lubricating Oils, Especially Emitted into the Environment
PublikacjaMineral base oil, a product of multistep fine refining of the relevant fractions from vacuum distillation of crude oil, is a main component of so-called mineral lubricating oils containing aliphatic and alicyclic substituted aromatic hydrocarbons, i.e., derivatives of benzene and biphenyl. Mineral lubricating oil is composed mostly of mineral base oil and a low amount of enriching additives, most often products of advanced organic...
-
Evaluating Asphalt Mix Ingredients by Moisture Susceptibility: The Development of a New Modified Boiling Test Procedure Based on Digital Imaging
Publikacja -
Regulated and Unregulated Exhaust Emissions from CNG Fueled Vehicles in Light of Euro 6 Regulations and the New WLTP/GTR 15 Test Procedure
Publikacja -
Multi-stage magnetic-fluid seals for operating in water - life test procedure, test stand and research results. Part II Results of life tests of multi-stage magnetic - fluid seal operating in water
PublikacjaThe edge criteria for magnetic-fluid seals durability research were described in previous article [24] and now the tests results are presented. The tests were made with three magnetic fluids using various magnets quantity in magnetic assemblies. If values obtained in the repeated test deviated by more than 10 % from results of the first test an additional control test was made for final characteristics. The characteristics are:...
-
An Investigation into Cold Start Emissions from Compression Ignition Engines using EU Legislative Emissions Test Procedures
Publikacja -
Loudness Scaling Test Based on Categorical Perception
PublikacjaThe main goal of this research study is focused on creating a method for loudness scaling based on categorical perception. Its main features, such as: way of testing, calibration procedure for securing reliable results, employing natural test stimuli, etc., are described in the paper and assessed against a procedure that uses 1/2-octave bands of noise (LGOB) for the loudness growth estimation. The Mann-Whitney U-test is employed...
-
The smoothness test for a density function
PublikacjaThe problem of testing hypothesis that a density function has no more than μ derivatives versus it has more than μ derivatives is considered. For a solution, the L2 norms of wavelet orthogonal projections on some orthogonal ‘‘differences’’ of spaces from a multiresolution analysis is used. For the construction of the smoothness test an asymptotic distribution of a smoothness estimator is used. To analyze that asymptotic distribution,...
-
Towards application of uncertainty quantification procedure combined with experimental procedure for assessment of the accuracy of the DEM approach dedicated for granular flow modeling
PublikacjaThere is a high demand for accurate and fast numerical models for dense granular flows found in many industrial applications. Nevertheless, before numerical model can be used its need to be always validated against experimental data. During the validation, it is important to consider how the measurement data sets, as well as the numerical models, are affected by errors and uncertainties. In this study, the uncertainty quantification...
-
Application of probabilistic tools to extend load test design of bridges prior to opening
PublikacjaLoad tests of bridges are widely performed in a large number of countries. Deterministic comparison of measurement results to the theoretical, FEM (finite element method)-based outcomes with possible further calibration is mostly applied. Sometimes, the data collected in the tests are also used to calibrate the reliability factors of bridge structures or their components. This work proposes to complement the stage of the load test...
-
An improved scalable method of isolating asphaltenes
PublikacjaA new, improved and scalable procedure of asphaltene fraction isolation is presented and compared to standard test methods. The new procedure uses 1:40 feedstock to solvent (n-heptane) ratio (g/mL), filtration through a cellulosic thimble and extensive washing in a Soxhlet type extractor. The group type composition and purity of the asphaltene fractions have been examined using thin-layer chromatography with flame-ionization detection....
-
Testing of low temperature behaviour of asphalt mixtures in bending creep test
PublikacjaThe paper presents a method of bending beam test and its importance for evaluation of asphalt mixtures behaviour at low temperatures. Two types of asphalt mixtures: asphalt concrete AC with normal paving grade bitumen and stone mastic asphalt SMA with SBS-modified bitumen were tested. Long-term oven ageing (LTOA) test was also used in the laboratory according to SHRP procedure. The Burgers model was applied and rheological parameters...
-
DEVELOPMENT OF THE ALGORITHM OF POLISH LANGUAGE FILM REVIEWS PREPROCESSING
PublikacjaThe algorithm and the software for conducting the procedure of Preprocessing of the reviews of films in the Polish language were developed. This algorithm contains the following steps: Text Adaptation Procedure; Procedure of Tokenization; Procedure of Transforming Words into the Byte Format; Part-of-Speech Tagging; Stemming / Lemmatization Procedure; Presentation of Documents in the Vector Form (Vector Space Model) Procedure; Forming...
-
Optimized 5-hour multiplex PCR test for the detection of tinea unguium: performance in a routine PCR laboratory
PublikacjaWe recently reported the development of a 5-hour multiplex PCR test for the detection of tinea unguium and the optimization of this test by the inclusion of an inhibition control. Here we report the performance of this procedure as used in a routine clinical laboratory as compared to conventional microscopy and culture-based techniques performed in a mycology reference laboratory. We found in processing 109 samples that 22 (20.2%)...
-
Experimental validation of the rolling resistance measurement method including updated draft standard
PublikacjaThe main objective of ROSANNE is the harmonisation and standardisation of the measurement of skid resistance, noise emission and rolling resistance of road pavements. Regarding rolling resistance characterisation, a draft for standardization of a harmonized procedure for classification of road surfaces across Europe has been prepared within WP3 (deliverable 3.5). The procedure deals with the direct measurement on real roads of...
-
Numerical methodology for evaluation the combustion and emissions characteristics on WLTP in the light duty dual-fuel diesel vehicle
PublikacjaThe worldwide aim of reducing environmental impact from internal combustion engines bring more and more stringent emission regulations. In 2017 by EU has been adopted new harmonized test procedure called WLTP. In general terms this test was designed for determining the levels of harmful emissions and fuel consumption of traditional and hybrid cars. This procedure contains specific driving scenarios which representing reallife driving...
-
Evaluation of Thermal Stresses in Asphalt Layers in Comparison with TSRST Test Results
PublikacjaThe paper presents the results of calculations and laboratory determination of thermal stresses at low temperatures. The modified Hills and Brien's method was used to calculate the thermal stresses in asphalt layers of pavements and the results were compared against the values obtained at a laboratory with the Thermal Stress Restrained Specimen Test (TSRST) method. The laboratory investigations were conducted using plain grade...
-
Comparison of pavement noise properties on selected road sections using different CPX measuring systems: self-powered vehicle and special test trailer
PublikacjaThe recently published ISO standard intended to measure the noise properties of road surfaces in a standardized method (ISO 11819-2:2017) precisely defines measurement procedure of the influence of road surface on traffic noise. According to it, two types of test vehicles may be utilized: a self-powered vehicle fitted with one or more test tyres and a trailer towed by a separate vehicle with one or more test tyres mounted on the...
-
Stanowisko do diagnostyki i regulacji wyzwalaczy przekaźników w obwodach lokomotyw elektrycznych
PublikacjaFast circuit breaker and protective relays play an important role of protecting locomotive’s electrical circuits from damage caused by short circuit or overload. Undisturbed operation and proper circuit protection depends on the technical condition and fine calibration of the over-current trips. Therefore the relays should be subject to periodic inspection and adjustment due to locomotive maintenance schedule. A test stand for...
-
FEM modelling of screw displacement pile interaction with subsoil
PublikacjaPredicting the-settlement characteristics of piles is an important element in the designing of pile foundations. The most reliable method in evaluating pile-soil interaction is the static load test, preferably performed with instrumentation for measuring shaft and pile base resistances. This, however, is a mostly post-implementation test. In the design phase, prediction methods are needed, in which numerical simulations play an...
-
Application of response surface methodology to optimize solid-phase microextraction procedure for chromatographic determination of aroma-active monoterpenes in berries
PublikacjaMost of scientific papers concern the qualitative or semi-quantitative analysis of aroma-active terpenes in liquid food matrices. Therefore, the procedure based on solid-phase microextraction and comprehensive two-dimensional gas chromatography-time-of-flight mass spectrometry for determination of monoterpenes in fresh berries was developed. The optimal extraction conditions using divinylbenzene-carboxen-polydimethylsiloxane fiber...
-
The radiated immunity test of an astable multivibrator for various supply voltages
Dane BadawczeThe dataset presents a result of measurements that are a part of electromagnetic field immunity tests. The radiated, radio frequency, immunity tests were carried out for a typical astable electronic multivibrator supplied from a power supply with an output voltage of 6V and 7.5 V. Tests of immunity of electronic systems to radiated radio frequency (RF)...
-
INFLUENCE OF TEST CONDITIONS ON TYRE/ROAD NOISE MEASURED BY THE DRUM METHOD
PublikacjaTyre/road noise is one of the most important environmental problems related to road traffic. Nowadays a few standard procedures of tyre/road noise measurements are in use. Unfortunately, measurement conditions specified within relevant standards are very different. For example, procedure described in ISO 11819-2 used for pavement investigations requires tyre load of 3200 N and capped inflation pressure of 200 kPa. At the same time...
-
Determination of the effective concentration of ketoprofen against the germination of Sorghum bicolor (sorghum) seeds
Dane BadawczeResearch data includes an attempt to determine the effective concentration of ketoprofen that inhibits germination of Sorghum bicolor (sorghum) seeds.
-
The conducted immunity test of a power supply unit in the frequency range from 19 MHz to 26 MHz for the RF voltage level of 3 V
Dane BadawczeThe dataset presents a result of measurements that are a part of immunity tests to conducted disturbances, induced by radio-frequency fields. The immunity tests were carried out on the mains cable of the DF1723003TC NDN power supply unit. Tests of immunity of electronic systems to conducted disturbances in the frequency range from 19 MHz to 26 MHz were...
-
The conducted immunity test of a power supply unit in the frequency range from 19 MHz to 26 MHz for the RF voltage level of 1 V
Dane BadawczeThe dataset presents a result of measurements that are a part of immunity tests to conducted disturbances, induced by radio-frequency fields. The immunity tests were carried out on the mains cable of the DF1723003TC NDN power supply unit. Tests of immunity of electronic systems to conducted disturbances in the frequency range from 19 MHz to 26 MHz were...
-
The conducted immunity test of a power supply unit in the frequency range from 19 MHz to 26 MHz for the RF voltage level of 10 V
Dane BadawczeThe dataset presents a result of measurements that are a part of immunity tests to conducted disturbances, induced by radio-frequency fields. The immunity tests were carried out on the mains cable of the DF1723003TC NDN power supply unit. Tests of immunity of electronic systems to conducted disturbances in the frequency range from 19 MHz to 26 MHz were...
-
Przygotowanie przemysłowego obiektu o stalowej konstrukcji nośnej do remontu po pożarze
PublikacjaW artykule przedstawiono warunki i sposób podejścia do naprawy stalowej konstrukcji nośnej kilkukondygnacyjnego obiektu przemysłowego, który uległ uszkodzeniu w wyniku oddziaływania wysokiej temperatury pożaru. Omówiono rodzaje badań i sprawdzeń oraz sposób przeprowadzenia kontroli konstrukcji, które stały się podstawą do wydania oceny technicznej o możliwości odbudowy i remontu obiektu, bez jego nadmiernej rozbiórki. Wskazany...
-
Analysis and Evaluation of the Working Cycle of the Diesel Engine
PublikacjaThe paper presents a proposal to apply a quantitative evaluation of the diesel engine with regard to the phenomena occurring during of a working cycle. The proposed procedure when analyzing test results from diesel engine is an attempt to transfer an engine activity evaluation methods in the operational time scale (exploit time), eg. in hours, to the micro-scale (dynamic time) relating only to the execution time of one (several)...
-
DETERMINATION OF DIFFUSIBLE HYDROGEN CONTENT IN DEPOSITED METAL OF RUTILE ELECTRODES BY GLYCERIN METHOD
PublikacjaThe presence of diffusible hydrogen in welded joints is one of the causes of formation the welding imperfections. Improvement of weldability can be achieved by reducing the hydrogen amount in welded joints. This requires, among others, the finding of sources of hydrogen. For high hydrogen processes the commonly used method of determining the diffusible hydrogen amount is the glycerin method. This paper concerns issues related to...
-
Coupling of Blood Pressure and Subarachnoid Space Oscillations at Cardiac Frequency Evoked by Handgrip and Cold Tests: A Bispectral Analysis
PublikacjaThe aim of the study was to assess blood pressure–subarachnoid space (BP–SAS) width coupling properties using time–frequency bispectral analysis based on wavelet transforms during handgrip and cold tests. The experiments were performed on a group of 16 healthy subjects (F/M; 7/9) of the mean age 27.2 ± 6.8 years and body mass index of 23.8 ± 4.1 kg/m². The sequence of challenges was first handgrip and then cold test. The handgrip...
-
Comparative model tests of SDP and CFA pile groups in non-cohesive soil
PublikacjaThe research topic relates to the subject of deep foundations supported on continuous flight auger (CFA) piles and screw displacement piles (SDP). The authors have decided to conduct model tests of foundations supported on the group of piles mentioned above and also the tests of the same piles working alone. The tests are ongoing in Geotechnical Laboratory of Gdańsk University of Technology. The description of test procedure, interpretation...
-
Assessment of technical condition and repair of steel structure elements on the example of fire damage in a warehouse building
PublikacjaThe paper analyses a case study on the structural assessment of warehouse building partially damaged by fire caused by external source (fire of lorries close to the building). The authors focus on the site investigations and laboratory test results prior to assessing actual condition of the structural elements. Both strengthening concept and repair procedure of a steel column are addressed here. A short literature survey in the...
-
The conducted immunity test of a power supply unit in accordance with EMC standards
Dane BadawczeThe dataset presents a result of measurements that are a part of immunity tests to conducted disturbances, induced by radio-frequency fields. The immunity tests were carried out on the mains cable of the DF1723003TC NDN power supply. Tests of immunity of electronic systems to conducted disturbances in the frequency range from 150 kHz to 230 MHz are...
-
The conducted immunity test of an AC adaptor in accordance with EMC standards
Dane BadawczeThe dataset presents a result of measurements that are a part of immunity tests to conducted disturbances, induced by radio-frequency fields. The immunity tests were carried out on the mains cable of the ac adaptor PHILIPS DC power supply SBC 6654. Tests of immunity of electronic systems to conducted disturbances in the frequency range from 150 kHz...
-
Short-Term Price Reaction to Filing for Bankruptcy and Restructuring Proceedings—The Case of Poland
PublikacjaThis study aims to check market reaction to filing for bankruptcy and restructuring proceedings and to verify the short-term effect of a price reversal in the Polish market in the years 2004–2019. The research was conducted by dividing the analysed companies according to the procedure (bankruptcy and restructuring) and market (the main market and the NewConnect market). The research methodology used in the study is the event analysis...
-
Problems of analytical determination of journal bearing bush fatigue strength estimates
PublikacjaProblems connected with determination of stress distribution in sliding layer of thinwalled bearing bushes, investigated in bearing fatigue test rigs, have been presented. Using an example of plain bearings tested in the fatigue machine SMOK (built at the Gdask University of Technology) problems with obtaining a convergence of iterative procedure for determining the fatigue strength estimators of bearing alloy surface layer are...
-
Vibro piles performance prediction using result of CPT
PublikacjaVibro piles belong to the group of full displacement piles with an expanded base, characterised by a very high load capacity, especially in non-cohesive soils. The problem is to adopt a reliable method for the determination of full load–settlement (Q–s) curve. A frequent difficulty is the determination of the load capacity limit based on the static load test because the course of the load–settlement curve is of a linear nature....
-
Cavitation Erosion of P110 Steel in Different Drilling Muds
PublikacjaThe P110 steel specimens were subjected to ultrasonic cavitation erosion in different compositions of drilling muds and surfactant additive. The test procedure was based on ASTM-G-32 standard recommendations. API 5CT-P110 steel is used for pipes in oil and gas industry. The harsh environment and high velocity of flows poses corrosive and erosive threat on materials used there. The composition of drilling fluid influences its rheological...
-
Zmodernizowany most Łazienkowski w Warszawie – analizy z wykorzystaniem modelu numerycznego MES
PublikacjaW artykule przedstawiono proces modelowania statycznego przęseł mostu Łazienkowskiego w Warszawie, który został poddany odbudowie po pożarze 14 lutego 2015 r. Sprawdzające obliczenia numeryczne wykonano w związku z badaniami konstrukcji podczas próbnego obciążenia. Przeprowadzono weryfikację obliczeń projektowych i zaprojektowano próbne obciążenie. Podsumowano wyniki analizy i badań. Dodatkowo opisano nową, stalową konstrukcję...
-
New Two-center Ellipsoidal Basis Function Neural Network for Fault Diagnosis of Analog Electronic Circuits
PublikacjaIn the paper a new fault diagnosis-oriented neural network and a diagnostic method for localization of parametric faults in Analog Electronic Circuits (AECs) with tolerances is presented. The method belongs to the class of dictionary Simulation Before Test (SBT) methods. It utilizes dictionary fault signatures as a family of identification curves dispersed around nominal positions by component tolerances of the Circuit Under Test...
-
Influence of image transformations and quality degradations on SURF detector efficiency
PublikacjaA method for task-oriented examination of SURF keypoint detector accuracy is presented in the paper. It consists of generating test images, based on a given exemplar, processed by affine transformations: random rotation and scaling, and varying degree of degradations: darkening, blurring, noising, and compression. Details of applied degradation procedure are presented, followed by essentials of SURF-based images matching. A distance...
-
Performance of Watermarking-based DTD Algorithm Under Time-varying Echo Path Conditions
PublikacjaA novel double-talk detection (DTD) algorithm based on techniques similar to those used for audio signal watermarking was introduced by the authors. The application of the described DTD algorithm within acoustic echo cancellation system is presented. The problem of DTD robustness to time-varying conditions of acoustic echo path is discussed and explanation as to why such conditions occur in practical situations is provided. The...
-
Robustness analysis of watermarking-based dtd algorithm under time-variable echo conditions
PublikacjaA novel double-talk detection (DTD) algorithm based on techniques similar to those used for audio signal watermarking was introduced by the authors. The application of the described DTD algorithm within acoustic echo cancellation system is presented. The problem of DTD robustness to time-varying conditions of acoustic echo path is discussed and explanation as to why such conditions occur in practical situations is provided. The...
-
Sensorless Disturbance Detection for Five Phase Induction Motor with Third Harmonic Injection
PublikacjaThe paper presents a sensorless disturbance detection procedure that was done on a five phase induction motor with third harmonic injection. A test bench was developed where a three phase machine serves as disturbance generator of different frequencies. The control of the machines is based on multi scalar variables that ensures an independent control of the motor EMF and the rotor flux. For disturbance identification a speed observer...
-
Analysis of exhaled breath for dengue disease detection by low-cost electronic nose system
PublikacjaThis paper presents a procedure and a set-up of an electronic nose system analyzing exhaled breath to detect the patients suffering from dengue – a mosquito-borne tropical disease. Low-power resistive gas sensors (MiCS-6814, TGS8100) were used to detect volatile organic compounds (VOCs) in the exhaled breath. The end-tidal phase of patients exhaled breath was collected with a BioVOCTM breath sampler. Two strategies were assessed...
-
Angular welding distortion - one sided fillet weld
Dane BadawczeWelding is the basic method of joining ship hull elements during its construction. However, this method of joining structural elements generates shrinks. Shrinks causes deformation of the entire welded structure, both linear and angular. In the shipbuilding industry, there is a tendency to oversize fillet welds, at the design as well as manufacturing...
-
Monitoring of current collectors on the railway line
PublikacjaProper cooperation the current collectors and the overhead line is a pre-requisite for reliable and safe operation of railway transport. Instances of maladjustment and, in some cases, damage to the current collectors, occur between periodic inspections of the rolling stock. In order to detect such anomalies quickly, the test stand was developed, with the aim of monitoring the technical state of the current collectors under operating...
-
A procedure for elastoplastic hardening function identification.
PublikacjaThe inverse analysis method for identifying a nonlinear hardening function,which governs a plastic yielding of soil and rock materials in the framework of elastoplastic theory is presented. A concept of two stage finite element based on spatial discretization of computational space and hardening function space is introduced. The proposed inverse analysis can be classified as the output least squares method. The Levenberg Marquard...