Filtry
wszystkich: 7283
-
Katalog
- Publikacje 5436 wyników po odfiltrowaniu
- Czasopisma 20 wyników po odfiltrowaniu
- Osoby 88 wyników po odfiltrowaniu
- Wynalazki 14 wyników po odfiltrowaniu
- Projekty 14 wyników po odfiltrowaniu
- Laboratoria 2 wyników po odfiltrowaniu
- Zespoły Badawcze 1 wyników po odfiltrowaniu
- Aparatura Badawcza 2 wyników po odfiltrowaniu
- Kursy Online 59 wyników po odfiltrowaniu
- Wydarzenia 8 wyników po odfiltrowaniu
- Dane Badawcze 1639 wyników po odfiltrowaniu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: POLE TEMPERATUROWE
-
High temperature corrosion of steel equipment in modern rafinery environments with high and low sulphur content
PublikacjaPrzedstawiono charakterystykę i mechanizmy procesów wysokotemperaturowej korozji elementów ze stali we współczesnych rafineriach ropy naftowej podczas eksploatacji we frakcjach węglowodorowych o niskiej i wysokiej zawartości siarki. Zwrócono uwagę na procesy korozji siarkowej w obecności wodoru i bez obecności wodoru oraz proces pylenia metalu pod wpływem węgla ze środowiska - w wypadku niskiej zawartości siarki w środowisku.
-
The effect of the wood temperature upon specific cutting resistance during machining with narrow-kerf saws
PublikacjaW pracy przedstawiono wyniki badań eksperymentalnych właściwego powierzchniowego oporu skrawania drewna sosny w funkcji wilgotności drewna, temperatury drewna oraz prędkości posuwu podczas przecinania cienkimi piłami. Proces cięcia prowadzono na pilarce ramowej wielopiłowej PRW15M. Sosnowe próbki przed badaniami mrożono w komorze klimatycznej - temperatura drewna -5 C deg., -20 C deg., +20 C deg. Czas wymrażania przed próbami określano...
-
Influence of wall temperature on heat transfer coefficient during R 22 boiling in microfin tube
PublikacjaPrzedstawiono wyniki badań współczynnika przejmowania ciepła i spadku ciśnienia podczas wrzenia czynnika R 22 w rurze nisko żebrowanej. Opisano stanowisko i procedurę badawczą. Zaobserwowano spadek współczynnika przejmowania. Opisano stanowisko i procedurę badawczą. Zaobserwowano spadek współczynnika przejmowania ciepła wraz ze wzrostem temperatury ścianki rury.
-
Surface morphology of PrBa2Cu3O7-ë single crystals after the long lasting high temperature reduction. .
PublikacjaZaprezentowano wyniki szczegółowej analizy powierzchni kryształów poddanych długotrwałej redukcji wysokotemperaturowej. Badania za pomocą skaningowej mikroskopii (SEM) wykazały obecność niestabilnych strukturalnie krystalitów powstałych w wyniku rozpadu powierzchni kryształów. Zanikanie zaindukowanego przy pomocy obróbki wysokotemperaturowej nadprzewodnictwa może być spowodowane migracją defektów podsieci Pr-Ba z wnętrza...
-
Dissolution of Nb-doped hydroxyapatite prepared via low-temperature mechanochemical method: Spectroscopy studies
PublikacjaCalcium phosphate glass ceramics with nominal hydroxyapatite stoichiometry doped with niobium were synthesized using simple as well as low-temperature mechanochemical method and then in the form of compressed pellet were submitted to the static dissolution process in distilled water for one month. The results of structural analysis, performed mainly on the base of spectroscopic methods such as: infrared absorption spectroscopy,...
-
Experimental study of the fuel jet combustion in high temperature and low oxygen content exhaust gases
PublikacjaPrzeprowadzono badania eksperymentalne spalania pojedynczego strumienia paliwa gazowego. Paliwo podawano współosiowo do generowanych przez konwencjonalny palnik gazowy spalin o wysokiej temperaturze i niskiej zawartości tlenu. Badano wpływ zawartości tlenu w utleniaczu na widzialność płomienia i skład produktów spalania.
-
Influence of CeO2 and TiO2 Particles on Physicochemical Properties of Composite Nickel Coatings Electrodeposited at Ambient Temperature
PublikacjaThe Ni-TiO2 and Ni-CeO2 composite coatings with varying hydrophilic/hydrophobic characteristics were fabricated by the electrodeposition method from a tartrate electrolyte at ambient temperature. To meet the requirements of tight regulation by the European Chemicals Agency classifying H3BO3 as a substance of very high concern, Rochelle salt was utilized as a buffer solution instead. The novelty of this study was to implement a...
-
Room temperature depinning of the charge-density waves in quasi-two-dimensional 1T-TaS2 devices
PublikacjaWe report on the depinning of nearly commensurate charge-density waves in 1T-TaS2 thin films at room temperature. A combination of the differential current–voltage measurements with the low-frequency noise spectroscopy provides unambiguous means for detecting the depinning threshold field in quasi-2D materials. The depinning process in 1T-TaS2 is not accompanied by an observable abrupt increase in electric current—in striking contrast...
-
A Computational Analysis of the Aerodynamic and Aeromechanical Behavior of a Thermo-Well for Steam Temperature Measurement in a Steam Turbine
PublikacjaThe goal of the paper is twofold: firstly, it presents computational fluid dynamics analysis for finding maximum unsteady flow forces (and their frequencies) acting on a thermo-well for measuring steam temperature in a steam turbine control stage and secondly, it presents computational solid dynamics analysis of possibility of entry into resonance of the thermowell structure. There have been analyzed two cases of flow with changing...
-
Influence of High Temperature Oxidation on Hydrogen Absorption and Degradation of Zircaloy-2 and Zr 700 Alloys
PublikacjaThe present research was aimed at determining the effects of the oxide layers on hydrogen absorption, microstructure and mechanical properties of the Zircaloy- 2 and Zr 702 alloys. The oxidation was made at 350 °C, 700 °C and 900 °C for 10 to 30 min in laboratory air, followed by hydrogen cathodic charging for 72 h and annealing at 400 °C for 4 h. The slow strain rate tests were carried out on oxidized, charged and annealed specimens. The...
-
Study of pH and temperature effect on lipophilicity of catechol-containing antioxidants by reversed phase liquid chromatography
PublikacjaLipophilicity of selected antioxidant phytochemicals, including flavonoids, phenolic acids and xanthonoids, was determined by reversed phase high performance liquid chromatography with UV detection (RP-HPLC-UV). The analyses run at different temperature and pH conditions in isocratic mode suggested that lipophilicity as distribution coefficient (logD) between aqueous and organic phase decreases with increasing temperature. For...
-
Glass-ceramic sealants and steel interconnects: accelerated interfacial stability and reactivity tests at high temperature
PublikacjaHigh-temperature reactions between glass-ceramic sealants and Fe-Cr alloy interconnects may lead to the formation of undesirable phases, and consequently degradation of solid oxide fuel/electrolyser devices. In this work, three different glass-ceramic sealants (Na-containing, Ba-containing, Sr-containing compositions) and Fe22Cr stainless steel powders (raw and pre-oxidised) are considered in order to test their chemical reactivity...
-
The vibration-based assessment of the influence of elevated temperature on the condition of concrete beams with pultruded GFRP reinforcement
PublikacjaConcrete beams reinforced with glass fiber reinforced polymer (GFRP) bars subjected to elevated temperature have been experimentally studied. The influence of high temperatures on GFRP-reinforced concrete beams condition has been check both, destructively and nondestructively. The nondestructive tests foresaw vibration-based tests to obtain the natural frequency values after exposure to varying temperatures. The vibration-based...
-
Effect of the let-through energy of overcurrent protective devices on the temperature of conductors during short-circuits
PublikacjaThe scope of the verification of low-voltage systems covers the earth fault loop impedance measurement. This measurement is usually performed with the use of low-value current meters, which force a current many times lower than the one occurring during a real short-circuit. Therefore, the international standard recommends consideration of the increase of resistance of conductors with the increase of temperature, which may occur...
-
High-temperature kinetics study of 430L steel powder oxidized in air at 600–850 °C
PublikacjaThe 430L stainless steel powder with a mean particle size of 95 μm was studied to determine its high-temperature oxidation properties. Continuous thermogravimetric measurements were carried out for 100 h in air at temperatures in the range of 600–850 °C. Even though a considerable amount of Cr (up to ˜5 wt.% Cr) inside the grains was depleted – especially inside small grains – no breakaway oxidation was observed. This indicates...
-
The analysis of temperature changes of the saliva traces left on the fur during laboratory rats social contacts
PublikacjaAutomatic analysis of complex rodent social be- havior, especially aggressive ones, is of important scientific interest. In this paper we analyze the properties of the data created as a result of aggressive rodent social behavior. Detec- tion of specific aggressive behaviors is based on the event of leaving traces of saliva on the fur of the attacked individual, which are clearly visible in the thermal imaging. The traces change...
-
High temperature oxidation behavior of SUS430 SOFC interconnects with Mn-Co spinel coating in air
PublikacjaIn this study, SUS430 alloy is evaluated for its high temperature corrosion properties as a possible material for interconnects of solid oxide fuel cells (SOFCs). Samples are coated with Mn-Co by commercial physical vapor deposition (PVD) process and oxidized in air for 1250 h at 800 °C. A dense cubic Mn-Co-Fe spinel layer is formed on the surface, showing great effect on corrosion reduction compared with the samples without coating....
-
Identification of damages in the inlet air duct of a diesel engine based on exhaust gas temperature measurements
PublikacjaThe temperature of the exhaust gas of a diesel piston engine, measured in the characteristic control sections of its thermo-flow system, can be a valuable source of diagnostic information about the technical condition of the elements limiting the working spaces thus separated, including the turbocharging system, but also its fuel supply system and replacement of the medium. In standard marine engine measurement systems equipped...
-
The Influence of Low-Temperature Disintegration on the Co-Fermentation Process of Distillation Residue and Waste-Activated Sludge
Publikacja: Innovative low-temperature disintegration (process temperature 55 ◦C and oxygen concentration 0.2 mg/dm3 ) can be an economically rational technology to intensifying energy production from renewable sources. The proposed process can achieve a degree of disintegration—under optimal conditions—of about 50%, which is excellent when compared with other methods of feed pre-treatment. The low-temperature disintegration of distillation...
-
Measurement of the Temporal and Spatial Temperature Distribution on the Surface of PVCP Tissue Phantom Illuminated by Laser Dataset
PublikacjaThe dataset entitled Measurement of the temporal and spatial temperature distribution on the surface of PVCP tissue phantom illuminated by laser was obtained with a laboratory set-up for characterisation of the thermal properties of optical tissue phantoms during laser irradiation. The dataset contains a single image file representing the spatial temperature distribution on the surface of a PVCP tissue phantom. This thermal image...
-
Fatigue life improvement using low transformation temperature weld material with measurement of residual stress
PublikacjaWelding processes often produce high levels of tensile residual stress. Low transformation temperature (LTT) welding wires utilise phase transformation strains to overcome the thermal contraction of a cooling weld. In this paper, the residual stress within each weld was quantified using the milling/strain gauge method, being the strain change measured as the weldment was milled away. The fatigue tests were conducted under uniaxial...
-
High Temperature Air/Steam Conversion of Biomass and Wastes Into Fuel Gas for Heat and Electricity Production
PublikacjaPaper present principle of high temperature air/staem gasification as well as some results of research using this technology for conversion of biomass and wastes into fuel gas.
-
Low temperature growth of diamond films on optical fibers using Linear Antenna CVD system
PublikacjaIt is not trivial to achieve a good quality diamond-coated fibre interface due to a large difference in the properties and composition of the diamond films (or use coating even) and the optical fibre material, i.e. fused silica. One of the biggest problems is the high temperature during the deposition which influences the optical fibre or optical fibre sensor structure (e.g. long-period gratings (LPG)). The greatest advantage of...
-
High Temperature Corrosion Evaluation of Porous Hastelloy X Alloy in Air and Humidified Hydrogen Atmospheres
PublikacjaIn this work a commercially available porous Hastelloy X alloy is characterized in terms of high temperature corrosion resistance. The alloy was oxidized in the temperature range from 500C to 900C in air and humidified hydrogen for 100 hours. Corrosion rates and porosity changes were measured. Microstructural characterization was performed using X-ray diffractometry and scanning electron microscopy. Results show that porous alloys...
-
Rheology studies of poly(lactic acid)-carbon black-nanodiamond composites
Dane BadawczeThis dataset contains rheology measurements carried out on new 3D printing-dedicated composites with poly-lactic acid (PLA), carbon black (CB) and nanodiamond fillers. Two types of nanodiamonds were studied: detonation nanodiamonds (DND) and boron-doped carbon nanowalls (BCNW). The investigated techniques was performed by melt mass-flow rates (MFR)....
-
Electrochemical studies of poly(lactic acid)-carbon black-nanodiamond composites
Dane BadawczeThis dataset contains electrochemical investigation on electrodes 3D printed using a new composite composed of poly-lactic acid (PLA), carbon black (CB) and nanodiamond fillers. Two types of nanodiamonds were studied: detonation nanodiamonds (DND) and boron-doped carbon nanowalls (BCNW). The presented results contain:1. electrochemical characterisation...
-
Mechanical studies of poly(lactic acid)-carbon black-nanodiamond composites
Dane BadawczeThis dataset contains mechanical tests carried out on new 3D printing-dedicated composites with poly-lactic acid (PLA), carbon black (CB) and nanodiamond fillers. Two types of nanodiamonds were studied: detonation nanodiamonds (DND) and boron-doped carbon nanowalls (BCNW). The investigated techniques was dynamic mechanical analysis (DMA). The measurements...
-
Internal electric fields in vacuum-evaporated films as studied by electroabsorption spectroscopy
PublikacjaMierzono sygnały elektroabsorpcji na I-szej harmonicznej częstości przykładanego sinusoidalnego pola elektrycznego w komórkach sandwiczowych Al/warstwa organiczna/Al. Wyznaczono elektryczne pola wewnętrzne (Fi) dla materiałów stosowanych w organicznych diodach elektroluminescencyjnych (TPD, TAPC, MTDATA, QAC, Alq3, Ir(ppy)3, PtOEP). Mechanizm powstawania pól Fi powiązano z pułapkowaniem ładunku w obszarach przyelektrodowych.
-
The effects of NP-POL, the nonapeptide constituent of Colostrinin, on intracellular antioxidant system
Publikacja -
Critical approach to PLE technique application in the analysis of secondary metabolites in plants
Publikacja -
Standardy zasilania sieci ethernetowych przez kable transmisyjne - rozwój PoE
PublikacjaW artykule przedstawiono rozwój koncepcji zasilania urzadzeń sieciowych przez standardowe kable ethernetowe, w szczególnosci opisano standard IEEE 802.3at. Zanalizowano również zastosowania i perspektywy rozwoju rozwišzań ethernetowych w domach prywatnych i przemyśle.
-
Temperature of formation of Au nanostructures
Dane BadawczeNanostructures were obtained via annealing of thin Au films. In order to determine possible nanoislands formation mechanisms, dependence on initial film thickness was examined. For the surface morphology studies, nanograin structure and chemical composition analysis, SEM, HR TEM and EDS measurements were performed, respectively. Morphology studies shown...
-
Testing an evaporator operation with a bifurcation manifold, condenser temperature 20 and evaporator temperature 85
Dane BadawczeThe experiment was conducted to test the evaporator operation. The heat exchanger was equipped with minigeometry (set of 50 parallel minichannels or single minigap). The studies were conducted for various mass flow rate of the working fluid and for various temperatures at the inlet of the evaporator. Accurate information about the test rig, the parameters...
-
Testing an evaporator operation with a trapezoidal manifold, condenser temperature 90 and evaporator temperature 90
Dane BadawczeThe experiment was conducted to test the evaporator operation. The heat exchanger was equipped with minigeometry (set of 50 parallel minichannels or single minigap). The studies were conducted for various mass flow rate of the working fluid and for various temperatures at the inlet of the evaporator. Accurate information about the test rig, the parameters...
-
Testing an evaporator operation with a bifurcation manifold, condenser temperature 20 and evaporator temperature 70
Dane BadawczeThe experiment was conducted to test the evaporator operation. The heat exchanger was equipped with minigeometry (set of 50 parallel minichannels or single minigap). The studies were conducted for various mass flow rate of the working fluid and for various temperatures at the inlet of the evaporator. Accurate information about the test rig, the parameters...
-
Testing an evaporator operation with a rectangular manifold, condenser temperature 30 and evaporator temperature 90
Dane BadawczeThe experiment was conducted to test the evaporator operation. The heat exchanger was equipped with minigeometry (set of 50 parallel minichannels or single minigap). The studies were conducted for various mass flow rate of the working fluid and for various temperatures at the inlet of the evaporator. Accurate information about the test rig, the parameters...
-
Testing an evaporator operation with a trapezoidal manifold, condenser temperature 70 and evaporator temperature 60
Dane BadawczeThe experiment was conducted to test the evaporator operation. The heat exchanger was equipped with minigeometry (set of 50 parallel minichannels or single minigap). The studies were conducted for various mass flow rate of the working fluid and for various temperatures at the inlet of the evaporator. Accurate information about the test rig, the parameters...
-
Testing an evaporator operation with a bifurcation manifold, condenser temperature 20 and evaporator temperature 95
Dane BadawczeThe experiment was conducted to test the evaporator operation. The heat exchanger was equipped with minigeometry (set of 50 parallel minichannels or single minigap). The studies were conducted for various mass flow rate of the working fluid and for various temperatures at the inlet of the evaporator. Accurate information about the test rig, the parameters...
-
Testing an evaporator operation with a bifurcation manifold, condenser temperature 20 and evaporator temperature 90
Dane BadawczeThe experiment was conducted to test the evaporator operation. The heat exchanger was equipped with minigeometry (set of 50 parallel minichannels or single minigap). The studies were conducted for various mass flow rate of the working fluid and for various temperatures at the inlet of the evaporator. Accurate information about the test rig, the parameters...
-
Role of the disulfide bond in stabilizing and folding of the fimbrial protein DraE from uropathogenic Escherichia coli
PublikacjaDr fimbriae are homopolymeric adhesive organelles of uropathogenic Escherichia coli composed of DraE subunits, responsible for the attachment to host cells. These structures are characterized by enormously high stability resulting from the structural properties of an Ig-like fold of DraE. One feature of DraE and other fimbrial subunits that makes them peculiar among Ig-like domain-containing proteins is a conserved disulfide bond...
-
Pomiar naprężeń własnych metodą Barkhausena za pomocą sondy z wirującym polem magnetycznym
PublikacjaW pracy przedstawiono nowy sposób pomiaru naprężeń własnych w elementach konstrukcji z wykorzystaniem polowego efektu Barkhausena. Informację o stanie naprężeń uzyskano z analizy rozkładu kątowego natężenia efektu Barkhausena zmierzonego w sposób automatyczny poprzez sondę z wirującym polem magnetycznym. Przedstawiono zasadę działania i opis układu pomiarowego oraz przykłady wykorzystania tej metody w ocenie stanu naprężenia w...
-
The Influence of UV Light on Performance of Poly(methyl Methacrylate) in Regard to Dye-Sensitised Solar Cells
Publikacja -
In vitro characteristics ofLactobacillusspp. strains isolated from the chicken digestive tract and their role in the inhibition ofCampylobactercolonization
Publikacja -
A role for accessory genes rI.-1 and rI.1 in the regulation of lysis inhibition by bacteriophage T4
Publikacja -
Exploring the Role of Ownership in International Entrepreneurship: How does Ownership Affect Internationalisation of Polish Firms?
Publikacja -
Development of nanoscale morphology and role of viscoelastic phase separation on the properties of epoxy/recycled polyurethane blends
PublikacjaA novel and cost-effective approach towards the modification of epoxy matrix has been developed using recycled polyurethane for the first time without sacrificing any of the intrinsic properties of the resin. Polyurethane, recycled from waste foam by glycolysis process (RPU), was found to be very effective in improving the properties of the thermosetting resin based on Diglycidyl ether of bisphenol-A (DGEBA). The effect of the...
-
Electron Scattering on X(CH3)4 Molecules: Applicability of Simple Additivity Rule and Role of Methylation
PublikacjaTo investigate influence of target methylation (substitution of a hydrogen atom by methyl group) on electron-collision processes we compare absolute total cross sections for XH4 and X(CH3)4 molecules, where X is Si and Ge, respectively. We also compare experimental TCSs energy dependencies with estimated data obtained using simple formula and TCSs for methyl group and those for SiH4 and GeH4. Electron-scattering TCSs for mentioned...
-
Morphology and properties of recycled polyethylene/ground tyre rubber/thermoplastic poly(ester-urethane) blends
PublikacjaThe growing amount of plastics waste produced every year resulted in development of mechanical and chemical recycling methods of polymers and their blends or composites. From the environmental point of view, the possibility of plastics waste reusing and recycling is desirable. In this study three polymer blends were obtained with using recycled polyethylene (RPE), ground tyre rubber (GTR) and thermoplastic poly(ester-urethane)...
-
Niederschalgswasser-Management in Polen. Aufgaben und organisatorische Strukturen am Beispiel der Stadt Danzig
PublikacjaDie wirksame Trennung der Abwasserströme sowie die extrem komplexen räumlichen Bedingungen sind das Hauptproblem der Niederschlagswasserbewirtschaftung in Danzig. In der Stadt gibt es sowohl Berg- als auch Tieflagen. Die bestehende Situation führte zu der Notwendigkeit, eine eigene kommunale Betriebsorganisation zu gründen, die sich um alle Bestandteile der Niederschlagswasserinfrastruktur (Kanäle im Innen- und Außenbereich, Bäche,...
-
Effect of particle size on the flame retardancy of poly(butylene succinate)/Mg(OH)2 composites
Publikacja