Wyszukiwarka
Filtry
wszystkich: 551
-
Katalog
Wyniki wyszukiwania dla: ZINC FERRITE
-
The role of slowly biodegradable organic compounds in a full-scale biological nutrient removal activated sludge systems
PublikacjaThe aim of this study was to determine the immediate effects of slowly biodegradable substrates on the denitrification capability and phosphate release/uptake interactions for a full-scale biomass process from two large wastewater treatment plants (WWTPs) located in the cities of Gdansk and Gdynia (northern Poland). Since it is hard to distinguish the slowly biodegradable substrate in a direct way, a novel procedure based on batch...
-
Enhancement of fiber-optic low-coherence Fabry-Pérot interferometer with ZnO ALD films
PublikacjaIn this paper investigation of the enhanced fiber-optic low coherence Fabry-Pérot interferometer with zinc oxide (ZnO) film deposited by atomic layer deposition (ALD) was presented. Model of the interferometer, which was constructed of single-mode optical fiber with applied ZnO ALD films, was built. The interferometer was also examined by means of experiment. Measurements were performed for both reflective and transmission modes,...
-
Measurement spectrum obtained with the use of ZnO coated microsphere-based fiber-optic sensor - microsphere inspection s.4
Dane BadawczeApplication of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements between 100°C and 300°C, is presented. The main advantage of integrating a fiber-optic microsphere with a sensing device is the possibility of monitoring the integrity of the sensor...
-
Measurement spectrum obtained with the use of ZnO coated microsphere-based fiber-optic sensor - microsphere inspection s.5
Dane BadawczeApplication of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements between 100°C and 300°C, is presented. The main advantage of integrating a fiber-optic microsphere with a sensing device is the possibility of monitoring the integrity of the sensor...
-
Measurement spectrum obtained with the use of ZnO coated microsphere-based fiber-optic sensor - microsphere inspection s.3
Dane BadawczeApplication of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements between 100°C and 300°C, is presented. The main advantage of integrating a fiber-optic microsphere with a sensing device is the possibility of monitoring the integrity of the sensor...
-
Badanie korelacji efektu emisji magnetoakustycznej ze zmianami mikrostruk- tury stali 10H2M. Zesz. Probl. - Badania Nieniszczące.**2003 nr 8 s. 67-70, 5 rys. bibliogr. 5 poz. Materiały 32 Krajowej Konferencji Badań Nieniszczących 32 KKBN. Międzyzdro-je 28-30. X. 2003 r.
PublikacjaPrzedstawiono wyniki badania korelacji efektu emisji magnetoakustycznej zezmianami mikrostruktury stali 10H2M w trakcie procesu degradacji. Rozwójkształtu i koncentracji wydzieleń wewnątrz ziarna i na granicy ziaren badanoanalizując obrazy mikrostruktury z mikroskopu skaningowego. Wykazano, że za-nik natężenia emisji magnetoakustycznej jest skorelowany ze wzrostem szero-kości wydzieleń na granicy ziaren ferrytu.
-
Projektowanie, synteza i charakterystyka fotokatalizatorów nowej generacji na bazie związku Ti3C2Tx do usuwania aktywnych substancji farmaceutycznych
PublikacjaCelem niniejszej pracy było zastosowanie materiałów nowej generacji na bazie związku Ti3C2Tx w procesach fotokatalitycznej degradacji aktywnych substancji farmaceutycznych: karbamazepiny, acetaminofenu i ibuprofenu. Zakres prac badawczych obejmował syntezę fotokatalizatorów, charakterystykę ich właściwości fizykochemicznych, oraz ocenę aktywności fotokatalitycznej. Przedstawiono możliwość zastosowania węglika tytanu jako kokatalizatora...
-
Corrosion fatigue crack propagation rate characteristics for weldable ship and offshore steels with regard to the influence of loading frequency and seawater temperature
PublikacjaAfter Vosikovsky (1975), the corrosion fatigue crack growth rate (CFCGR) characteristics have been divided into three regions. The region-III rates are very close to mechanical fatigue crack growth rates. CFCGR formulae, including the long-crack length effect (in region I only), the loading frequency effect (in region II only), and the saltwater temperature effect, have been proposed. It has been assumed that CFCGR is proportional...
-
ENVIRONMENTAL DEGRADATION OF DISSIMILAR AUSTENITIC 316L AND DUPLEX 2205 STAINLESS STEELS WELDED JOINTS
PublikacjaThe paper describes structure and properties of dissimilar stainless steels welded joints between duplex 2205 and austenitic 316L steels. Investigations were focused on environmentally assisted cracking of welded joints. The susceptibility to stress corrosion cracking (SCC) and hydrogen embrittlement was determined in slow strain rate tests (SSRT) with the strain rate of 2.2 × 10–6 s–1. Chloride-inducted SCC was determined in the...
-
IMPACT-TOUGHNESS INVESTIGATIONS OF DUPLEX STAINLESS STEELS
PublikacjaDuplex stainless steels are very attractive constructional materials for use in aggressive environments because of their several advantages over austenitic stainless steels. Duplex steels have excellent pitting and crevice corrosion resistance, are highly resistant to chloride stress-corrosion cracking and are about twice as strong as common austenitic steels. Better properties are associated with their microstructures consisting...
-
Progress in the post weld residual stress evaluation using Barkhausen effect meter with a novel rotating magnetic field probe
PublikacjaWe report the progress in post weld residual stress evaluation using Barkhausen effect (BE) meter with rotating magnetic field probe. The novel probe of the BE meter contains two C-core electromagnets and searching coil with ferrite antenna. This meter allows automatic measurements of BE intensity envelopes at different angles of magnetizing field. The full process of measurement at given position of the probe takes about only...
-
Ferromagnetic nanoparticles imaging by means of Magnetic Force Microscopy
Dane BadawczeFerromagnetic nanoparticles can be used as building blocks for advanced thin film magnets, and can also be used in data storage and biomedical technologies. Nano-crystalline ferrites with the chemical formula NixZn (1 - x) Fe2O4, where x = 0, 0.2, 0.4, 0.6, 0.8, 1.0 show anti-corrosion properties and suppress electromagnetic interference, in the case...
-
Modeling two phase flow in large scale fractured porous media with an extended multiple interacting continua method
PublikacjaWe present a two phase flow conceptual model, the corresponding simulator (2pMINC) and a workflow for large-scale fractured reservoirs, based on a continuum fracture approach which uses the multiple interacting continua (MINC) method complemented with an improved upscaling technique. The complex transient behavior of the flow processes in fractured porous media is captured by subgridding the coarse blocks in nested volume elements...
-
Wow defect reduction based on interpolation techniques
PublikacjaW referacie przedstawiono wyniki badania różnych technik interpolacji wykorzystanych w redukcji kołysania dźwięku. W badaniach użyto: interpolację liniową, dwie techniki interpolacji wielomianowej (Hermite i spline), i technikę sumowania okienkowanych funkcji sink. Jakość rekonstrukcji wykonano wykorzystując sztucznie spreparowany sygnał audio, rekonstruowany wymienionymi metodami interpolacji. Jakość rekonstrukcji oceniono wykorzystując...
-
Microscale diamond protection for a ZnO coated fiber optic sensor
PublikacjaFiber optic sensors are widely used in environmental, biological and chemical sensing. Due to the demanding environmental conditions in which they can be used, there is a risk of damaging the sensor measurement head placed in the measuring field. Sensors using nanolayers deposited upon the fiber structure are particularly vulnerable to damage. A thin film placed on the surface of the fiber end-face can be prone to mechanical damage...
-
Honey as an indicator of heavy metals in the environment
PublikacjaHoney bees collect nectar, pollen and honeydew to produce bee products. One of them is honey, which due to chemical composition and properties is considered by human as a valuable food product. When honey bees collect substrates to produce honey they can bring contaminants to the hive. The presence of xenobiotics in bee products may lower their quality and devalue their properties, and also endanger human health. Many scientists...
-
Fiber-optic sensors based on microspheres with nanocoatings (Zastosowanie mikrosfer optycznych z cienkowarstwowymi pokryciami w czujnikach światłowodowych)
PublikacjaTemperature is one of the most important physical quantities. Temperature measurements are used in every field of life, especially electronics, electrical engineering, energy-related fields, including energy source and storage devices. The goal of this dissertation is to design and optimize the microsphere-based fiber-optic sensors construction for measurement of the sensor surrounding medium temperature, including selection of...
-
Microporous N-Doped Carbon Obtained from Salt Melt Pyrolysis of Chitosan toward Supercapacitor and Oxygen Reduction Catalysts
PublikacjaThe direct carbonization of low-cost and abundant chitosan biopolymer in the presencesalt eutectics leads to highly microporous, N-doped nanostructures. The microporous structureeasily manufactured using eutectic mixture (ZnCl2 -KCl) and chitosan. Potassium ions here can act as an intercalating agent, leading to the formation of lamellar carbon sheets, whereas zinc chloride generates significant porosity. Here, we present an efficient...
-
Diamond protection for reusable ZnO coated fiber-optic measurement head in optoelectrochemical investigation of bisphenol A
PublikacjaDue to the global problem with plastic contaminating the environment, with bisphenol A (BPA) being one of the highest demand, effective monitoring and purification of the pollutants are required. The electrochemical methods constitute a good solution but, due to polymerization of electrochemical oxidation bisphenol A products and their adsorption to the surfaces, measurement head elements are clogged by the formed film. In this...
-
Accumulation of radioisotopes and heavy metals in selected species of mushrooms
PublikacjaSeven species of forest mushrooms from different regions of Poland (edible: Imleria badia, Cantharellus cibarius, Xerocomus subtomentosus, Suillus luteus and inedible by humans but being food for animals: Paxillus involutus, Tylopilus felleus and Russula emetica) were analyzed for radioisotope activity (Cs-137, K-40, Bi-214 and Pb-210) as well as concentrations of heavy metals (aluminum, chromium, cadmium, manganese, iron, lead,...
-
Local electrochemical impedance spectroscopy in dynamic mode of galvanic coupling
PublikacjaA novel method that combines local electrochemical impedance spectroscopy and mapping in dynamicmode is proposed. Method was validated over two galvanic couplings, namely zinc/copper and cad-mium/copper. Impedance spectrum response for all measuring points was obtained by means ofsimultaneous implementation of selected range of frequencies. Proposed method allows the measure-ment in a more time-efficient manner, at the same time...
-
Nanolayers in Fiber-Optic Biosensing
PublikacjaIn this chapter, fiber-optic sensors based on nanolayers or thin films and their ability to perform biophotonic measurements is presented. In the last decade, fiber-optic sensors have gained popularity as biosensing devices. This has been made possible because of the design and the integration of new materials in fiber-optic technology. Nanolayers and thin films made from various materials such as nanodiamond (NCD), boron-doped...
-
Solvent Exchange around Aqueous Zn(II) from Ab Initio Molecular Dynamics Simulations
PublikacjaHydrated zinc(II) cations, due to their importance in biological systems, are the subject of ongoing research concerning their hydration shell structure and dynamics. Here, ab initio molecular dynamics (AIMD) simulations are used to study solvent exchange events around aqueous Zn2+, for which observation in detail is possible owing to the considerable length of the generated trajectory. While the hexacoordinated Zn(H2O)62+ is the...
-
Measurement spectrum obtained with the use of ZnO coated microsphere-based fiber-optic sensor - 130 Celsius degrees
Dane BadawczeApplication of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements between 100°C and 300°C, is presented. The main advantage of integrating a fiber-optic microsphere with a sensing device is the possibility of monitoring the integrity of the sensor...
-
Measurement spectrum obtained with the use of ZnO coated microsphere-based fiber-optic sensor - 110 Celsius degrees
Dane BadawczeApplication of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements between 100°C and 300°C, is presented. The main advantage of integrating a fiber-optic microsphere with a sensing device is the possibility of monitoring the integrity of the sensor...
-
Measurement spectrum obtained with the use of ZnO coated microsphere-based fiber-optic sensor - 120 Celsius degrees
Dane BadawczeApplication of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements between 100°C and 300°C, is presented. The main advantage of integrating a fiber-optic microsphere with a sensing device is the possibility of monitoring the integrity of the sensor...
-
Measurement spectrum obtained with the use of ZnO coated microsphere-based fiber-optic sensor - 100 Celsius degrees
Dane BadawczeApplication of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements between 100°C and 300°C, is presented. The main advantage of integrating a fiber-optic microsphere with a sensing device is the possibility of monitoring the integrity of the sensor...
-
Mechanical and structural behavior of high-strength low-alloy steel pad welded by underwater wet welding conditions
PublikacjaThe aim of the paper was to determine the metallurgical and mechanical behaviors of a high-strength low-alloy (HSLA) steel pad-welded specimen used in the structures of industrial and naval parts. Then to predict the metallurgical consequences (nature of the phases present) and the mechanical properties (hardness and impact strength) of the pad-welded steel obtained by underwater wet welding with different heat input values. The...
-
The influence of the welding thermal cycles on corrosion resistance of duplex stainless steel
PublikacjaBadano skłonnośc strefy wpływu ciepła spoin ze stali dupleks do korozyjnego pękania narężeniowego. Wykonano próby korozyjne z wykorzystaniem metody SSRT w środowisku korozyjnym wrzącego MgCl2. Wykazano, że duży udział ferrytu w strukturze SWC pogarsza odpornośc na korozję. Badania metalograficzne na mikroskopie lektronowym wykazały różne sposoby propagacji pęknięcia zależnie od zawartości austenitu w strukturze SWC.
-
Application of boron-doped diamond film and ZnO layer in the Fabry-Pérot interferometer
PublikacjaIn this article there have been presented the use of boron-doped diamond films for sensor applications. The low-finesse Fabry-Pérot interferometer working in the reflective mode has been implemented. Two kinds of reflective layers have been elaborated: boron-doped diamond thin films and zinc-oxide (ZnO) layer. Thin ZnO layers were deposited by Atomic Layer Deposition (ALD) on the face of a standard telecommunication single-mode...
-
Solid-contact lead(II) ion-selective electrodes for potentiometric determination of lead(II) in presence of high concentrations of Na(I), Cu(II), Cd(II), Zn(II), Ca(II) and Mg(II)
PublikacjaLead and its compounds are a serious threat to the environment. Monitoring of this toxic heavy metal is a driving force for the continuous development of novel lead(II) ionophores to be applied in ion-selective electrodes. In this work a highly selective lead(II) ionophore, namely 25,26,27,28-tetrakis(piperidinylthiocarbonylmethylene)-p-tert-butylcalix[4]arene, was used in solid-contact ion-selective electrodes for determination...
-
Induced-fit binding of laccase to gold and carbon electrodes for the biological fuel cell applications
PublikacjaAnalogues of laccase natural substrates (syringic, veratric, ferulic, vanillic, isovanillic, 3,5-dimethoxybenzoic aldehydes) were employed to bind and orient laccase molecules in a way which facilitates adsorption of the catalyst molecules and their electrical connection with the conductive support. Laccase was bound efficiently to these substrates both on gold and carbon electrodes forming, respectively, 2D and 3D films sensitive...
-
Crystal facet effects in photocatalytic degradation of organic pollutants over anatase TiO2
PublikacjaPresented work show detailed effect of the exposed crystal facets of anatase TiO2 on the photocatalytic degradation of organic pollutants. The most important existing information about the geometry and electronic properties of the low index anatase facets are summarised. During the performed works, anatase nanoparticles with the dominant exposition of either {0 0 1}, {1 0 0} or {1 0 1} crystal facets were prepared and their photocatalytic...
-
Suspended matter, composition and fluxes, Gdansk Deep, late spring 2001
Dane BadawczeParticulate organic carbon (POC) and nitrogen (PON) concentrations and fluxes were measured in the Gdańsk Deep (Gulf of Gdansk) from 30.05 to 06.06.2001. The vertical profiles of POC and PON were characterised by the highest values in the euphotic layer, a gradual decrease with depth, and an increase below the halocline. The hydrophysical conditions...
-
Young shoots of red cabbage are a better source of selected nutrients and glucosinolates in comparison to the vegetable at full maturity
PublikacjaCruciferous vegetables are a valuable source of ingredients with health benefits. The most characteristic compounds of cruciferous vegetables with identified anticancer properties are glucosinolates. Young shoots and sprouts of red cabbage are becoming a popular fresh food rich in nutrients and bioactive compounds. The objective of this research was to determine, for the first time in a comprehensive approach, whether young shoots...
-
Synthesis of CoFe2O4 Nanoparticles: The Effect of Ionic Strength, Concentration, and Precursor Type on Morphology and Magnetic Properties
PublikacjaThe present study highlights the effect of metal precursor types (SO4 2¯, Cl¯, and NO3¯), their concentration, and the influence of ionic strength of reaction environment on the morphology, surface, and magnetic properties of CoFe2O4 particles. The magnetic nanoparticles were obtained by chemical coprecipitation in alkaline medium at increasing metal concentration in the range of 0.0425 mol·dm-3 to 0.17 mol·dm-3 and calcination...
-
Ziziphora taurica subsp. taurica: Analytical Characterization and Biological Activities
Publikacja -
O możliwości stosowania magnetycznych nieniszczących metod badań stanu mikrostruktury stali P92.
PublikacjaZbadano właściwości magnetyczne stali P92 (pętle histerezy B(H), natężenie efektu Barkhausena HEB oraz emisji magnetoakustycznej EMA) po obróbce termicznej, mającej wytworzyć 4 typy mikrostruktury (odpuszczony martenzyt, drobne pierwotne ziarno austenitu, małą gęstość dyslokacji, ferryt). Wykazano, iż zmiany mikrostruktury znacząco zmieniają HEB oraz EMA. Stanowi to przesłankę dla opracowania nieniszczącej magnetycznej metody oceny...
-
A Database Schema for the Analysis of Global Dynamics of Multiparameter Systems
Publikacja -
Evaluation of Selected Heavy Metal Contaminants as Well as Nitrates and Nitrites in the Microgreens of Nigella (Nigella sativa L.), Safflower (Carthamus tinctorius L.), and Camelina (Camelina sativa L.) at Different Stages of Vegetation
PublikacjaMicrogreens are a new, rapidly growing group of foodstuffs. The decorative function of these is often accompanied by their use in traditional dishes. As microgreens are eaten at very early stages, when the development of the epidermis is at its minimum, the bioavailability of minerals will be found to be higher in microgreens then in mature vegetables. So, microgreens can be an excellent functional food, especially for mineral-deficient...
-
Generalized Einstein relation in disordered organic semiconductors: Influence of the acoustic phonons–charge carriers scattering
PublikacjaIn this work, we analyze the generalized Einstein relation for disordered organic semiconductors with a non-equilibrium Druyvesteyn-type distribution function. The Druyvesteyn behavior of hot electrons in a solid state is associated with the acoustic phonons–charge carriers scattering. Such a case has been experimentally demonstrated in electroluminescent inorganic rare–earth–doped zinc chalcogenides. Therefore, we can assume that,...
-
Role of size scale of ZnO nanoparticles and microparticles on toxicity toward bacteria and osteoblast cancer cells
PublikacjaThe specific role of size scale, surface capping, and aspect ratio of zinc oxide (ZnO) particles on toxicity toward prokaryotic and eukaryotic cells was investigated. ZnO nano and microparticles of controlled size and mor- phology were synthesized by wet chemical methods. Cytotoxicity toward mammalian cells was studied using a human osteoblast cancer cell line and antibacterial activity using Gram-negative bacteria (Escherichia...
-
Submicron inorganic particles as an additional filler in hybrid epoxy matrix composites reinforced with glass fibres
PublikacjaIn this study, the effect of selected submicron metal oxide (zinc oxide, titanium oxide) or non-metal oxide (silicon dioxide) particles on mechanical and thermo-mechanical properties of epoxy/glass composites was investigated. The applied epoxy resin was a diglycidyl ether of bisphenol-A cured with triethylenetetramine. As a reinforcement twill weave E-glass fabric was used. Hybrid composites (contained particulate and fibrous...
-
Mechanical and Microstructural Characterization of TIG Welded Dissimilar Joints between 304L Austenitic Stainless Steel and Incoloy 800HT Nickel Alloy
PublikacjaIn this article, the mechanical properties and microstructure of 304L austenitic stainless steel/Incoloy 800HT nickel alloy dissimilar welded joints are investigated. The joints were made of 21.3 mm × 7.47 mm tubes using the TIG process with the use of S Ni 6082 nickel filler metal. No welding imperfections were found and high strength properties of joints were obtained, meeting the assumed acceptance criteria of the product’s...
-
The Influence of the Depth of Cut in Single-Pass Grinding on the Microstructure and Properties of the C45 Steel Surface Layer
PublikacjaThe paper contains the results of a metallographic examination and nanoindentation test conducted for the medium carbon structural steel with low content of Mn, Si, Cu, Cr, and Ni after its grinding to a depth ranging from 2 μm to 20 μm, at constant cutting speed (peripheral speed) of vs = 25 ms−1 and constant feed rate of vft = 1 m/min. Applied grinding parameters did not cause the surface layer hardening, which could generate...
-
Tensile test of 1.4307 / X2CrNi18-9 / AISI 304L grade austenitic steel
Dane BadawczeShip structures and their components are build mainly of steel. Hull steel is used to build the hull structure. Some structural elements, such as RSW (Refrigerated See Water) tanks, or LNG (Liquid Natural Gas) tanks - gas transported at temperatures below -162° C, are build from austenitic steels. Austenitic steels have a different microstructure and...
-
Tensile test of 1.4541 / X6CrNi18-10 / AISI 321 grade austenitic steel
Dane BadawczeShip structures and their components are build mainly of steel. Hull steel is used to build the hull structure. Some structural elements, such as RSW (Refrigerated See Water) tanks, or LNG (Liquid Natural Gas) tanks - gas transported at temperatures below -162° C, are build from austenitic steels. Austenitic steels have a different microstructure and...
-
Wpływ temperatury przesycania na właściwości złączy spawanych rur ze stali typu Lean Duplex 2101
PublikacjaW artykule przedstawiono wpływ temperatury przesycania w powiązaniu z technologią spawania wzdłużnego metodą TIG (142) rurek stosowanych w budowie wy-mienników ciepła ze stali Lean Duplex 2101. Przedstawiono wyniki badań wytrzymałości na rozciąganie, prób technologicznych określających właściwości plastyczne, makro- i mikro-skopowe oraz pomiaru zawartości ferrytu delta metodą magnetyczną. Ustalono, że zmiana temperatury przesycania...
-
The energy approach to fatigue crack growth of S355 steel welded specimens subjected to bending
PublikacjaThe study presents the results of the research on the rate of fatigue crack growth subjected to bending in the ferritic-pearlitic structure. The studies were carried out at a constant amplitude of the moment and at various values of the load ratios R and at the operating frequency of the machine of 28.4 Hz. Flat specimens made of S355 steel and with fillet welds and with double-sided blunt external notches as well as concave...
-
Realizacja bezprzewodowej sieci czujników w standardzie ZigBee
PublikacjaPrzedstawiono koncepcję budowy bezprzewodowej sieci ZigBee, z wykorzystaniem mikrokontrolerów firmy MicroChip Technology Inc. oraz modułów radiowych wykonanych na układzie CC2420 i pracujących w paśmie częstotliwości 2,5GHz. Podano szczegóły dotyczące opracowanego oprogramowania realizującego zadania routingu. Opisano najistotniejsze problemy techniczne, jakie pojawiają się przy realizacji sieci bezprzewodowej w tym standardzie.