Wyszukiwarka
Katedra Inżynierii Materiałowej i Spajania
Publikacje
Filtry
wszystkich: 732
Katalog Publikacji
Rok 2012
-
Badanie wpływu budowy przestrzennej stali austenitycznej 316L na jej odporność kawitacyjną
Publikacja -
Bioactive core material for porous load-bearing implants
PublikacjaSo far state of knowledge on biodegradable materials is reviewed. Among a variety of investigated materials, those composed of polymers and ceramics may be considered as only candidates for a core material in porous titanium alloy. The collagen and chitosan among natural polymers, polyhydroxy acids among synthetic polymers, and hydroxyapatite and tricalcium phosphate among ceramics are proposed for further research. Three essential...
-
Cavitation Erosion Resistance of Austenitic Stainless Steel after Glow-Discharge Nitriding Process
PublikacjaThis paper presents investigation of cavitation erosion resistance of nitrided austenitic stainless steel X5CrNi18-10. The diffusion layers were produced by using different parameters of atmosphere (N2:H2). The microstructure, chemical composition and phase identification of the modified layer were examined using scanning electron microscopy, glow-discharge optical emission spectrometer and X-ray diffractometry, respectively. Cavitation...
-
Characterization of Bi6Fe2Ti3O18 Ceramics with Impedance Spectroscopy
PublikacjaIn the present research the tool of impedance spectroscopy was utilized to characterize dielectric behavior of Aurivillius-type ceramics of Bi6Fe2Ti3O18 composition fabricated by hot pressing method from the stoichiometric mixture of oxides Bi2O3, TiO2 and Fe2O3. Impedance spectroscopy was applied to characterize dielectric response of bulk, grain boundary, and material/electrode interfaces of the fabricated polycrystalline ceramic...
-
Comparision of mechanical properties of nitrided cases and remelted layers of austenitic stainless steel
Publikacja -
Degradation of Gel-Coat Layer in Glass/Polyester Laminate in Seawater Environment
PublikacjaGlass/polyester laminate coated with gelcoat layer of different thickness 0,5; 1,5; 3 mm was studied in terms of blistering behaviour and water sorption in hot water environment. Blistering was found to be accelerated for thin (0,5 mm) gel-coat layer compared to the thick (1,5; 3 mm), however no significant difference in blistering behaviour was observed between the laminates with gel-coat thickness 1,5 and 3 mm which may suggest...
-
Design of thermal cutting table - welding technology and construction
PublikacjaW referacie przedstawiono pionierską pracę dyplomową stopnia inżynierskiego, wykonaną przez dwoje studentów Wydziału Mechanicznego Politechniki Gdańskiej zgodnie z systemem CDIO (Conceive, Design, Implement, Operate). W ramach pracy studenci zaprojektowali stół do cięcia termicznego metali (rysunki i obliczenia wytrzymałościowe metodą elementów skończonych), opracowali technologię spawania stołu oraz samodzielnie go wykonali. Stół...
-
Determination of Failure Causes of a Steam Turbine Casing
PublikacjaThe paper presents results of research and failure analysis undertaken to determine failure causes of a steam turbine casing. After 130,000 hours of service the crack in a outer shell of the turbine casing was found. The inner shell of the casing was made of cast steel grade G21CrMoV5-7, and the outer shell of grade G20CrMo4-5. Following research were performed in order to determine causes of the casing failure: chemical analysis;...
-
Determining diffusible hydrogen amounts using the mercury method. Welding International
PublikacjaW artykule przedstawiono szczegółową charakterystykę procedury oznaczania ilości wodoru dyfundującego metodą rtęciową na tle innych metod badawczych i aktualnego stanu wiedzy dotyczącego rozpatrywanego zagadnienia. Omówiono klasyfikację wodoru występującego w złączu spawanym oraz metody oznaczania ilości wodoru dyfundującego w stopiwie ze zwróceniem szczególnej uwagi na metodę rtęciową jako metodę podstawową. Zestawiono zależności...
-
Effect of crystallization process at cryogenic conditions on the functional properties of the SUPERSTON alloy used in production the ship's propellers
PublikacjaThe purpose of this paper is to show results of laser treatment at cryogenic conditions of the SUPERSTON alloy used for ship's propellers. That modification process ought to bring beneficial changes of microstructure and residual stresses in the surface layer. During the laser remelting at cryogenic conditions the microstructure changes significantly. This is related to synergistic effects of the solidification rate, phase transformations...
Rok 2013
-
Badanie wpływu budowy przestrzennej stopu NiTi na jego odporność kawitacyjną
PublikacjaReferat stanowi wprowadzenie teoretyczne do oceny możliwości dalszego zwiększania odporności kawitacyjnej stopów opartych na fazach międzymetalicznych. autor opisuje stan wiedzy, jaki można znaleźć w literaturze na temat sposobów zwiększania odporności kawitacyjnej materiałów. Zaprezentowano również własne spostrzeżenia i ich odniesienie do występujących w literaturze teorii. Podano prace, jakie są wykorzystywane w chwili obecnej...
-
Biological hazards in low noise, poroelastic road surfaces
PublikacjaDrainage pavements as well as poroelastic pavements ("PERS") are a very efficient way to decrease traffic noise by reducing tire/road noise at the source as well as noise propagation over the road surface. Many noise generating mechanisms at the tire/road interface are very much reduced by road porosity (pipe resonance, "air pumping", Helmholtz resonance and the horn effect). A well-designed porous or poroelastic road surface may...
-
Budowa stanowiska do rejestracji różnicy koloru żelkotu eksploatowanego w środowisku wodnym
PublikacjaW artykule przedstawiono rozważania na temat budowy stanowiska do oceny różnicy kolorów ΔE laminatów z żelkotem po ekspozycji w środowisku wodnym. Przedstawiono dobór parametrów badania koloru metodą różnicową za pomocą układu oświetleniowego i aparatu fotograficznego. Przedstawiono wyniki pomiaru różnicy koloru w czasie dla laminatów epoksydowo szklanych w środowisku wodnym o zróżnicowanej temperaturze.
-
CDIO IN GDANSK: PEOPLE-ORIENTED STRATEGY
PublikacjaThe CDIO system implementation in Poland meets problems and Gdansk University of Technology (GUT) is still a single higher education institution in Poland accepted as the member of CDIO Initiative. The paper detects and characterizes the existing problems to be solved. In particular, the different groups of people are considered as supporters or fighters against CDIO idea, their attitudes being considered and applied strategy demonstrated. The...
-
Comparative X-ray diffraction and Mössbauer spectroscopy studies of BiFeO3 ceramics prepared by conventional solid-state reaction and mechanical activation
PublikacjaThe aim of this work was to prepare BiFeO3 by modified solid-state sintering and mechanical activation processes and to investigate the structure and hyperfine interactions of the material. X-ray diffraction and Mössbauer spectroscopy were applied as complementary methods. In the case of sintering, BiFeO3 phase was obtained from the mixture of precursors with 3 and 5 % excess of Bi2O3 during heating at 1023 K. Small amounts of...
-
DEGRADATION OF GFRP MARINE LAMINATES WITH NANO PARTICLE MODIFIED COATINGS
PublikacjaWater absorption and surface blistering behaviour was studied for polyester-matrix laminates with SiO2 nanoparticle reinforced gel coats. Accelerated water immersion tests at 37°C showed that addition of 10% nanoparticles increases blisters incubation time by ca. 50% compared to 5% and 0% nanoparticles composites.
-
DETERMINATION OF DIFFUSIBLE HYDROGEN CONTENT IN DEPOSITED METAL OF RUTILE ELECTRODES BY GLYCERIN METHOD
PublikacjaThe presence of diffusible hydrogen in welded joints is one of the causes of formation the welding imperfections. Improvement of weldability can be achieved by reducing the hydrogen amount in welded joints. This requires, among others, the finding of sources of hydrogen. For high hydrogen processes the commonly used method of determining the diffusible hydrogen amount is the glycerin method. This paper concerns issues related to...
-
DYNAMIC MECHANICAL BEHAVIOUR OF GFRP COMPOSITES WITH SiO2 NANO PARTICLES REINFORCED EPOXY MATRIX
PublikacjaDynamic mechanic (DMA) tests were performed to compare the mechanical behaviour of glass fibre reinforced epoxy laminate composites with SiO2 nanoparticle reinforced matrix. The selection of the most promising nanoparticle concentrations was considered in terms of elastic modulus and glass transition temperature. The reference specimens (0% nanoparticles) did not contain diluent accordingly the results do not allow the exact comparison...
-
Education at the Faculty of Mechanical Engineering of the Gdańsk University of Technology
PublikacjaFaculty of Mechanical Engineering is one of the largest departments of the Gdańsk University of Technology (GUT), currently educating about 3 000 student. Lectures are conducted in five Chairs, which include 18 Divisions. In 2000 GUT introduced the European Credit Transfer and Accumulation System (ECTS). Each student should get during one academic year 60 ECTS points. Obtaining a diploma of BEng requires the acquisition of no less...
-
Education at the Faculty of Mechanical Engineering of the Gdańsk University of Technology
PublikacjaFaculty of Mechanical Engineering is one of the largest departments of the Gdańsk University of Technology (GUT), currently educating about 3 000 student. Lectures are conducted in five Chairs, which include 18 Divisions. In 2000 GUT introduced the European Credit Transfer and Accumulation System (ECTS). Each student should get during one academic year 60 ECTS points. Obtaining a diploma of BEng requires the acquisition of no less...
-
Effect of Bi2O3 Excess on Morphology and Structure of BiNbO4 Ceramics
PublikacjaGoal of the present research was to fabricate BiNbO4 ceramics from the mixture of powders by the solid state reaction route and pressureless sintering at various temperatures (TS =8700C and TS =9100C) and study microstructure, phase composition and crystalline structure of BiNbO4 ceramics. Four batches were fabricated and examined, namely the one fabricated from the stoichiometric mixture of reagent – grade oxide powders, viz....
Rok 2016
-
Badanie wpływu zmian natężenia prądu na spawanie stopu aluminium
PublikacjaStop aluminium AW-7075 zyskuje coraz większą popularność w zastosowaniach komercyjnych ze względu na jego wyjątkowe właściwości fizyczne i mechaniczne: małą gęstość, wysoką wytrzymałość, udarność i plastyczność, bardzo dużą odporność na zmęczenie i zadowalającą na korozję, łatwą obrabialność i przetwarzalność. Ze względu na te właściwości, stop ten (AlZn5,5MgCu), zwany też FORTAL-em, używany jest dla części narażonych na wysokie...
-
Cavitation Erosion of P110 Steel in Different Drilling Muds
PublikacjaThe P110 steel specimens were subjected to ultrasonic cavitation erosion in different compositions of drilling muds and surfactant additive. The test procedure was based on ASTM-G-32 standard recommendations. API 5CT-P110 steel is used for pipes in oil and gas industry. The harsh environment and high velocity of flows poses corrosive and erosive threat on materials used there. The composition of drilling fluid influences its rheological...
-
Crystal structure and physical properties of new Ca2TGe3 (T = Pd and Pt) germanides
PublikacjaThe crystallographic, electronic transport and thermal properties of Ca2PdGe3 and Ca2PtGe3 are reported. The compounds crystalize in an ordered variant of the AlB2 crystal structure, in space group P6/mmm, with the lattice parameters a = 8.4876(4) Å/8.4503(5) Å and c = 4.1911(3) Å/4.2302(3) Å for Ca2PdGe3 and Ca2PtGe3, respectively. The resistivity data exhibit metallic behavior with residual-resistivity-ratios (RRR) of 13 for...
-
Effect of Linear Energy and Microstructure on the Content of Residual Hydrogen in Welded Joints made of Superduplex Steels
PublikacjaThe article presents tests concerning the content of retained hydrogen present in FCAW and SAW welded joints made of superduplex steel. The use of various welding technologies resulted in the obtainment of welds having different microstructures and ferrite contents. Measurements of retained hydrogen present in joints (performed using the complete combustion method) revealed various contents of hydrogen in the base material and...
-
Effect of plasma sprayed and laser re-melted Al2O3 coatings on hardness and wear properties of stainless steel
PublikacjaCommercially available austenic stainless steel substrate was coated with commercially available, raw Al2O3 powder applied by means of plasma spraying method and then re-melted with CO2 laser beam of various parameters. Tribological and mechanical properties of the 120 J/mm and 160 J/mm laser re-melted coatings were compared with the tribological and mechanical properties of the “as-sprayed” coating. The influence of the laser...
-
Effect of Semiconductor Element Substitution on the Electric Properties of Barium Titanate Ceramics
PublikacjaThe investigated ceramics were prepared by a solid-state reaction from simple oxides and carbonates with the use of a mixed oxide method (MOM). The morphology of BaTi0.96Si0.04O3 (BTSi04) ceramics was characterised by means of a scanning electron microscopy (SEM). It was found that Si+4 ion substitution supported the grain growth process in BT-based ceramics. The EDS results confirmed the high purity and expected quantitative composition...
-
EFFECT OF SURFACE STATE AND STRESS ON AN OXIDATION OF THE ZIRCALOY-2 ALLOY
PublikacjaZr alloys are widely used as materials for nuclear fuel pellets in the nuclear industry. In the case of the LOCA or RIA happen, a temperature may locally reach high values. Even if the high temperature maintains shortly, the zirconium oxides may become permeable, absorb hydrogen appearing in cooling water from decomposition reaction and crack because of formation and brittle failure of hydrides. Such model cannot so far take into...
Rok 2017
-
Badanie wpływu zmiany składu gazów osłonowych na spawanie metodą MIG stopu aluminium EN AW 7075. Innowacyjne wykorzystanie w wiertnictwie.
PublikacjaStop aluminium AW-7075 zyskuje coraz większą popularność w zastosowaniach komercyjnych ze względu na jego wyjątkowe właściwości fizyczne i mechaniczne: małą gęstość, wysoką wytrzymałość, udarność i plastyczność, bardzo dużą odporność na zmęczenie i zadowalającą na korozję, łatwą obrabialność i przetwarzalność. Ze względu na te właściwości, stop ten (AlZn5,5MgCu), zwany też FORTAL-em, używany jest dla części narażonych na wysokie...
-
Bioaktywność i biofunkcyjność cementu kostnego
PublikacjaOpracowanie dotyczy modyfikacji cementu kostnego w celu nadania mu właściwości bioaktywnych i biofunkcyjnych. Jego celem jest scharakteryzowanie cementu kostnego oraz obecnie stosowanych dodatków, któr e nadają mu właściwości przeciwdrobnoustrojowe oraz osteointegracyjne. Opracowanie zawiera opis badań własnych przeprowadzonych przez autorkę w aspekcie wytwarzania powłoki antybakteryjnej...
-
Corrosion behavior of hydrogen charged super duplex stainless steel welded joints
PublikacjaThe electrochemical behavior of the weld metal, heat-affected zone (HAZ), and base material of super duplex stainless steel (SDSS) welded joints, made with the application of flux-cored arc welding (FCAW) and submerged arc welding (SAW), were investigated with the use of metallographic examinations (optical microscopy and scanning electron microscopy), potentiodynamic polarization measurements and total hydrogen content determination...
-
Corrosion degradation of spacers – examination of changes in bone cement coating.
PublikacjaSpacer is a special implant used at the time of infection after endoprosthetic surgery. It consists of a metal core and bone cement coating with an antibiotic. In the human body spacers are exposed to degradation processes. This paper looks at the effect of corrosion on spacers. Electrochemical corrosion tests were performer on titanium pins with bone cement coating in two solutions: Ringer’s solution and artificial...
-
Degradation of implantable materials – in vivo and in vitro research
PublikacjaThe article concerns the biological and electrochemical degradation of metallic implants in vivo and in vitro studies. The in vivo research dealt with degradation of plates used to join bones, as well as endoprostheses. The most common damages were: metalosis, breaking in the microstructure changes, breaking in area of holes, as well as plastic deformation throughout the length of an implant. The material used for the research...
-
Degradation of reference tyres used for CPX measurements
PublikacjaMeasurements of tyre/road noise using the Close Proximity Method are based on reference tyres that are described in ISO/TS 11819-3. The standard specifies two tyres, namely "P1" and "H1" that should be used during measurements. To be used for measurements each tyre must fulfill certain conditions that are listed in the standard. The conditions are related to the tread pattern depth and rubber hardness. During experiments performed...
-
Deposition of phosphate coatings on titanium within scaffold structure
PublikacjaPurpose: Existing knowledge about the appearance, thickness, and chemical composition of phosphate coatings on titanium inside porous structures is insufficient. Such knowledge is important for the design and fabrication of porous implants. Methods: Metallic scaffolds were fabricated by selective laser melting of 316L stainless steel powder. Phosphate coatings were deposited on Ti sensors placed either outside the scaffolds or...
-
DIAGNOSTYKA STANU TECHNICZNEGO IZOLATORÓW PRZEPUSTOWYCH ŚREDNIEGO NAPIĘCIA
PublikacjaW referacie przedstawiono zasady sprawdzania jakości izolatorów przepustowych średniego napięcia (SN) za pomocą metody radiograficznej (RT) oraz pomiaru wyładowań niezupełnych (wnz). Ostatnie badanie jest jedną z pozycji zawartych w badaniach wyrobu normy [5]. Dodatkowo badania te rozszerzono o próby napięciem probierczym przemiennym. Z uwagi na negatywne wyniki pomiaru wnz za pomocą metody RT udało się określić lokalizację wtrąceń...
-
Diffusible hydrogen management in underwater wet self-shielded flux cored arc welding
PublikacjaThis article reports the effect of underwater wet welding parameters and conditions on the diffusible hydrogen content in deposited metal for welding with a self-shielded flux cored wire. The diffusible hydrogen content in deposited metal was determined using the glycerin method according to the Plackett-Burman design determining the significance of the effect of the stick out length, welding current, arc voltage, travel speed...
Rok 2014
-
Bead-on-plate welding on S235JR steel by underwater local dry chamber process
PublikacjaThe article presents the results of the effect of parameters of underwater local dry chamber welding on the properties of padding welds. The effect of heat input and the type of shielding gas on the structure and hardness of welds was established. the functions for estimating the maximum hardness of the heat affected zone have been also elaborated.
-
BIOMATERIALS AND IMPLANTS IN CARDIAC AND VASCULAR SURGERY - REVIEW
PublikacjaCurrently, on prosthesis in cardiac blood vessels and heart valves are used materials of animal or synthetic origin. For animal materials include, among others pericardial sac in which is the heart. Materials such as this (natural) are characterized by a remarkable biocompatibility within the human body, but their main disadvantage is the relatively low durability. In turn, synthetic materials, which include the austenitic chromium-nickel-molybdenum...
-
Comparative in vitro research of the Human Aortic Bioprosthesis
PublikacjaE valuate of the usefulness and reliability of structures based on the analysis of recorded parameters determining the flow through the Human Aortic Bioprosthesis (HAB) have been dealt with. By flow parameters changes determining the performance environment of prosthesis analyzed change of the motion dynamics of the valve leaflets as a function of pressure, thereby determining the degree of alignment of the prosthesis to the performance...
-
Comparison of road and laboratory measurements of tyre/road noise
PublikacjaTyre/road noise is one of the major environmental problems related to road traffic. There are several measuring methods of tyre/road noise that may be carried out on the road (for example Coast-down and Close Proximity Method) or in the laboratory (Drum Method). Road measurements are preferred for evaluations of pavement properties while laboratory methods are mostly used to evaluate tyres. One of the biggest problems associated...
-
Dielectric Properties of BiNbO<sub>4</sub>-Based Ceramic-Polymer Composites with 0-3 Connectivity
PublikacjaIn the present study two-phase BiNbO4//PVDF composites with 0-3 connectivity were studied by impedance spectroscopy within the frequency range Δν=100Hz-1MHz at room temperature. Polyvinylidene fluoride (PVDF) acted as a matrix whereas bismuth niobate (BiNbO4) powder acted as a dispersed phase. The volume fraction of the ceramic phase was cV=2, 4, 6, 8, 10, 16 and 20vol%. Analysis of the impedance data registered for composites...
-
Diffusible hydrogen content in deposited metal of multilayer welded joints
PublikacjaThe article describes manufacturing technology of multilayer joints in terms of control the diffusible hydrogen content. Diffusible hydrogen content in deposited metal for multilayer welded joints made of covered rutile electrodes or covered cellulosic and basic electrodes was determined. It was found that after four beads, the diffusible hydrogen content decreases in the case of the first technology from 36 ml/100 g to 18 ml/100...
-
Diffusible Hydrogen Control in Flux Cored Arc Welding Process
PublikacjaOne of the types of hydrogen degradation of steel welded joints is cold cracking. The direct cause of the formation of cold cracks is simultaneous presence of hydrogen, residual stresses and brittle structure. The way of preventing the occurring of degradation is to eliminate at least one of these factors. Practice has shown that the best solution is to control the amount of hydrogen in deposited metal. In this paper an experimental...
-
Effect of microstructure on mechanical properties and corrosion resistance of 2205 duplex stainless steel
PublikacjaThis paper presents results of the research on impact of microstructure of austenitic-ferritic steel of duplex type on its mechanical properties and susceptibility to stress corrosion cracking. As showed, improper processing technologies more and more often used in shipbuilding industry for plates and other half-finished products made of duplex steel may cause significant lowering their properties, which frequently makes their...
-
Effect of microstructure on mechanical properties of BA1055 bronze castings
PublikacjaThe article presents research results performed on aluminum bronze CuAl10Fe5Ni5 (BA1032) castings used for marine propellers. Metallographic studies were made on light microscope and a scanning electron microscope to assess quantitatively and qualitatively the alloy microstructure. It has been shown that the shape, size and distribution of the iron-rich phase precipitates in bronze microstructure significantly affect its mechanical...
Rok 2011
-
Beam on elastic foundation with anticlastic curvature: Application to analysis of mode I fracture tests
PublikacjaA first order correction is proposed taking into account both interface elasticity and transverse anticlastic curvature of flexible substrate(s) in the DCB (and related tests). Adherends are represented by Kirchhoff-Love plates, and the interface by Winkler-type elastic foundation. Two functions are introduced, representing evolution of beam deflection along the sample midline and anticlastic curvature along the plate. A method...
-
Certyfikowanie nurków-spawaczy przy spawaniu mokrym pod wodą w warunkach hiperbarycznych
PublikacjaW artykule omówiono wymagania normy PN-EN ISO 15618-1:2002: Egzamin kwalifikacyjny spawaczy w zakresie spawania podwodnego. Część 1: Spawacze-nurkowie spawający na mokro w warunkach hiperbarycznych. Podano zakresy możliwych do uzyskania zakresów kwalifikacji, wytyczne odnośnie wszystkich zmiennych zasadniczych ujętych w normie oraz przykłady oznaczenia uprawnień nurka-spawacza. Wskazano treści, które należy poddać analizie przy...
-
Corrosion resistance examinations of Ti6Al4V alloy with the use of potentiodynamic method in Ringer`s and artificial saliva solutions
PublikacjaThe research results of corrosion resistance of the Ti6Al4V alloy in the simulated body fluids (SBF) are presented. The polished specimens have shown better corrosion resistance than grinded surfaces in both liquids. The artificial saliva has revealed more aggressive test solution than Ringer`s solution. The pitting tendency has been observed in Ringer`s solution for grinded specimens.
-
Effect of shielded electrode wet welding conditions on diffusible hydrogen content in deposited metal
PublikacjaWet welding is the most popular method of joining in water enviroment. During underwater welding, the weldability of steel is limited by the higher cooling rates and hydrogen content in weld metal. Article presents results of preliminary tests on the effects of wet welding conditions on diffusible hydrogen amount. Seven parameters were optimized using a Plackett-Burman plan to get the most relevant variables. These parameters were:...
Rok 2010
-
Biocompatibility and bioactivity of load-bearing metallic implants
PublikacjaThe main objective of here presented research is to develop the titanium (Ti) alloy base composite materials possessing better biocompatibility, longer lifetime and bioactivity behaviour for load-bearing implants, e.g. hip joint and knee joint endoprosthesis. The development of such materials is performed through: modeling the material behaviour in biological environment in long time and developing of new procedures for such evaluation;...
-
Biocompatibility and Bioactivity of Load-Bearing Metallic Implants
PublikacjaThe main objective of here presented research is to develop the titanium (Ti) alloy base composite materials possessing better biocompatibility, longer lifetime and bioactivity behaviour for load-bearing implants, e.g. hip joint and knee joint endoprosthesis. The development of such materials is performed through: modeling the material behaviour in biological environment in long time and developing of new procedures for such evaluation;...
-
Charakterystyka korozji typu pylenie metalu w rafineryjnej instalacji platformingu CCR
PublikacjaW artykule przedstawiono charakterystykę procesu pylenia metalu w stali 9Cr-1Mo eksploatowanej w piecach instalacji platformingu CCR. Wykazano, że mechanizm niszczenia stali nie zależy od czasu eksploatacji i od stopnia konwersji wsadu, a krótkotrwały wzrost stężenia związków siarki we wsadzie może zwiększyć szybkość tworzenia pyłu.
-
Degradation of metal implants covered with silver
PublikacjaSilver was known for its antibacterial properties as long ago as in antiquity. The silver ions have ability to join the bacteria surface. Low density of silver ions Ag+ influence the protons through the bacteria surface, which results in total destruction of the cell. Antibacterial activity of silver remains in proportion with the density of silver ions Ag+ in the environment.
-
Degradation of metallic implants
PublikacjaPresence of metallic implants made of stainless steels, Co and Ti alloys is sometimes followed by some undesired allergic reactions and inflammatory processes and consequently the necessity of reimplantation.
Rok 2020
-
Biological and mechanical properties of bone cement with nanoarticles - in vitro and in vivo research
PublikacjaDespite antibiotic preventive treatment both before and after implant implementation, the risks of infection are real. These infections develop at the implant surface a few months after inserting them into the body. To prevent the development of bacteria and reduce the risk of infection, implants coated with nanoparticles are used. The Mechanical Department of the Technical University of Gdansk carries out research into using bone...
-
COLLABORATIVE LEARNING ENVIRONMENT FOR ENGINEERING EDUCATION (COLED)
PublikacjaCollaborative Learning Environment for Engineering Education is a European project implemented under the Erasmus + program, The main goal of 5 partners from 4 different European countries – Bulgaria, Poland, Portugal and Romania is to develop an innovative collaborative training approach, encompassing curricula related to the introduction of enterprise automation. Project activities are carried out in the period from Dctober 2018...
-
Comprehensive Evaluation of the Biological Properties of Surface-Modified Titanium Alloy Implants
PublikacjaAn increasing interest in the fabrication of implants made of titanium and its alloys results from their capacity to be integrated into the bone system. This integration is facilitated by different modifications of the implant surface. Here, we assessed the bioactivity of amorphous titania nanoporous and nanotubular coatings (TNTs), produced by electrochemical oxidation of Ti6Al4V orthopedic implants’ surface. The chemical composition...
-
Degradation of ferritic X10CrAlSi18 stainless steel caused by slurry
PublikacjaThe slurry erosion tests of ferritic X10CrAlSi18 steel were carried out using a slurry pot device. In order to investigate the erosion process, two series of tests were performed: first one with a constant impact velocity of 5 m/s, 7 m/s and 9 m/s and the second one, during which the impact velocity was changed after every exposure. During each test, an influence of test conditions on volume loss, surface hardness and roughness...
-
Dissimilar underwater wet welding of HSLA steels
PublikacjaThe high-strength low-alloy S460ML and S460N steels were chosen for underwater wet welding of dissimilar T-joints using covered electrodes. For improving the quality of joints, the temper bead welding (TBW) method was used. The application of TBW in pad welding conditions has been investigated earlier but the possibility of usage of this technique in welded joints was not analyzed. The main aim of the study was to check the influence...
-
Effect of electrode waterproof coating on quality of underwater wet welded joints
PublikacjaIn this paper, the effects of different hydrophobic coatings on the surface of covered electrodes on the quality of wet welded carbon steel joints were discussed. Commonly available hydrophobic substances used in industrial applications were selected for the research. The aim of using waterproof coatings was to check the possibility to decreasing the susceptibility of highstrength low-alloy S460N steel to cold cracking. During...
Rok 2019
-
Biological and mechanical properties of bone cement with nanoparticles - in vivo and in vitro research
PublikacjaDespite antibiotics preventive treatment, before and after an implant implementation, risk of infection are real. These infections at the implant surface develop in a few months after applying them into the body. To prevent the development of bacteria and to reduce the risk of infection, implants coated with nanoparticles come into use. The Mechanical Department of the Technical University of Gdańsk carried out a research with...
-
Cavitation Erosion Resistance Influence of Material Properties
PublikacjaThe cavitation erosion is the phenomena that causes degradation of fluid flow machinery components due to repetitive implosion of cavitation bubbles adjacent to the solid surface. Cavitation erosion is a complex phenomenon, which includes not only hydrodynamic factors of liquid, but also properties of erodible material e.g. microstructure, hardness or Young modulus. In order to reduce the negative impact of erosion on machine components,...
-
CHALK & TALK OR SWIPE & SKYPE?
PublikacjaTechnology in classroom is a matter of heated discussions in the field of education development, especially when multidisciplinary education goes along with language skills. Engineers’ education requires theoretical and practical knowledge. Moreover, dedicated computer skills become crucial for both young graduates and experienced educators on the labor market. Teaching online with or without using different Learning Management...
-
Charakterystyka procesu utleniania stopów cyrkonu i jego wpływu na stan warstwy wierzchniej oraz desorpcję wodoru
PublikacjaZjawiska degradacji tlenowej i wodorowej stopów cyrkonu mają istotne znaczenie dla modelowania mechanizmów utraty spójności koszulek paliwowych w warunkach katastrof nuklearnych, szczególnie typu LOCA. Celem naukowym pracy było poznanie i analiza zachowania utlenionych, komercyjnych stopów cyrkonu, wpływu wodoru na utlenione stopy oraz przedstawienie fizycznych źródeł i matematycznych zależności pomiędzy tymi zjawiskami. Wyniki...
-
Comparison of Properties of the Hybrid and Bilayer MWCNTs—Hydroxyapatite Coatings on Ti Alloy
PublikacjaCarbon nanotubes are proposed for reinforcement of the hydroxyapatite coatings to improve their adhesion, resistance to mechanical loads, biocompatibility, bioactivity, corrosion resistance, and antibacterial protection. So far, research has shown that all these properties are highly susceptible to the composition and microstructure of coatings. The present research is aimed at studies of multi-wall carbon nanotubes in three different...
-
Design and material selection for a patient transport device in field hospitals
PublikacjaACKGROUND: A major cause of patient and hospital worker injuries occurs transferring patients between two planes. The main aim of this paper was to propose a design of patient’s lift and transfer apparatus for use in field hospitals. The assumption was to design lightweight, durable and ergonomic device using innovative material. The authors concentrated on partial elimination of manual lifting in order to device could work both...
-
Determination of moisture resistance of covered electrodes according to PN-EN ISO 14372
PublikacjaMoisture present in the electrode covering is one of the sources of diffusible hydrogen in welded joints. In order to study the diffusible hydrogen content in deposited metal, a stand for moisturizing covered electrodes, in accordance with the PN-EN ISO 14372 standard, was built. After the stand was completed, a test of moisturizing the electrodes was carried out and measurements of the diffusible hydrogen content in deposited...
-
Effect of aeration of antibiotic-loaded bone cement on its properties and bactericidal effectiveness
PublikacjaBACKGROUND: Antibiotic-loaded bone cements are now widely used in medicine. They are able to locally deliver antibiotic particles and they allow treat or protect against infection. It is assumed that the bactericidal effectiveness of bioactive bone cements depend on the parameters of its production. Hence, the aim of this study was to check the effect of aeration of bone cement before mixing the components on its properties as...
-
Effect of selective laser treatment on initiation of fatigue crack in the main part of an undercarriage drag strut
PublikacjaThis paper presents the results of material characterization and a fatigue test conducted for a laser-re-melted drag strut used in an aircraft landing gear. The drag strut was re-melted with a CO2 laser beam. Eight re-melted paths were made in the form of spiral lines along the axis of the drag strut. Next, the drag strut was subjected to variable loads on a testing machine simulating loads occurring when an aircraft lands. The...
-
Effect of Storage Conditions of Rutile Flux Cored Welding Wires on Properties of Welds
PublikacjaThe influence of storage locations of two grades of rutile flux cored welding wires on their surface condition and the strength of the welds made with them were studied. Wires were stored in real urban conditions (Gdańsk and Katowice) for 1 month, simultaneously recording changes in conditions: temperature and relative humidity of the environment. Visual tests of wires in the delivered and stored condition as well as visual and...
Rok 2018
-
Biomechanical testing of bioactive bone cements – a comparison of the impact of modifiers: antibiotics and nanometals
PublikacjaApart from its bone filler and fracture stabilizing function, bone cement can be used as a carrier of bioactive substances, and such modified bone cement can protect the implant against microorganisms, treat local infections and combat bacteria introduced during the surgical procedure. In this paper, the effects of modifying antibiotics and nanosilver on the biomechanical properties of bone cement were examined. The following tests...
-
Biopolyols obtained via microwave-assisted liquefaction of lignin: structure, rheological, physical and thermal properties
PublikacjaThe present study examined the application of polyols obtained via microwave-assisted liquefaction of lignin in the production of rigid polyurethane foam. Lignin was liquefed in crude glycerol and 1,4-butanediol at diferent temperatures (130–170 °C), without a catalyst and using various biomass concentrations (15 and 30 wt%). The physicochemical properties, process yield, and FTIR-based identifcation of the obtained polyols were...
-
Cavitation Erosion – Phenomenon and Test Rigs
PublikacjaThe cavitation and cavitation erosion phenomenon have been shortly presented. The main four types of test rigs to investigate the cavitation erosion resistance have been shown. Each type of test design is described and an example of a design is shown. A special attention has been payed to the designs described in the International ASTM Standards: a vibratory design and a cavitating jet cell. There was shown that the design of a...
-
COLD CRACKING OF S460N STEEL WELDED IN WATER ENVIRONMENT
PublikacjaThis paper shows results of weldability testing of fine-grained high -strength low- alloy S460N steel welded in water environment by covered electrodes. The tests were carried out by using the CTS test specimens with fillet welds. Four specimens were welded under water and one specimen in air. Welded joints were subjected to non-destructive visual and penetration tests. The accepted joints were then subjected to macroscopic and...
-
COMPOSITE MATERIAL SELECTION FOR A PATIENT TRANSFER ASSIST DEVICE
PublikacjaLaminates - layered composites containing at least two elements (matrix and reinforcement) widely used in industry have also found their usage in medicine. Their main feature is the ability to modify the material in order to obtain the required properties. Depending on the needs, we can modify reinforcement, type of resin or the method of bonding substrates. Commonly used fibers are: carbon fiber, glass and aramid fibers; resins...
-
Composites in energy storing prosthetic feet
PublikacjaComposites reinforced with carbon and glass fibers have become the commonly used material in the production of energy storing prosthetic feet (ESPF/elastic feet prostheses). Their properties ensure a stable and light structure that allows for accumulation, storage and release of energy during walking, thus ensuring an increase in gait efficiency. Depending on the modification of the composite in terms of fiber selection, their...
-
Decreasing CO2 Emissions By Reducing Tire Rolling Resistance
PublikacjaThe first motor vehicle was built by Nicolas Cugnot almost 250 years ago and since then there has been a continuous process of motor vehicles’ improvements, as well as development of new road pavements. The fuel crisis of the 70s of the 20th century made it clear to vehicle builders that measures should be taken to reduce vehicle fuel consumption and it contributed to an increased interest in electric vehicles. Although significant...
-
Determinants of the surface quality, density and dimensional correctness in selective laser melting of the Ti-13Zr-13Nb alloy
PublikacjaSelective laser melting is widely used for custom-designed elements. Successful manufacturing depends on laser treatment parameters and material features. This research aimed to determine the effects of laser power, scan time and hatch distance on surface quality, relative density and dimensional precision for cuboids made of the Ti-13Zr-13Nb alloy. The influence of energy density, energy flux and pre-heating was seen to be decisive...
-
Dobór urządzeń do zgrzewania oporowego punktowego z wykorzystaniem analizy skupień
PublikacjaW pracy omówiono zagadnienie doboru urządzeń do zgrzewania oporowego punktowego, stwierdzając na podstawie przeglądu literatury, że nie istnieje obiektywna metoda wspomagająca decyzję zakupu takich zgrzewarek. Do rozwiązania problemu zaproponowano zastosowanie metod analizy skupień. Zgromadzono i opracowano dane diagnostyczne opisujące 35 zgrzewarek oporowych punktowych, a następnie przeprowadzono ich klasyfikacje metodami Warda...
-
Effect of the Post-Weld Surface Condition on the Corrosion Resistance of Austenitic Stainless Steel AISI 304
PublikacjaSurfaces of welded elements made of corrosion-resistant (stainless) steels develop temper colours. The removal of thickened oxide layers off steels exposed to temperatures below 300°C is necessary and entails the restoring of high corrosion resistance of the stainless steel. The article presents tests concerned with the effect of a method applied to remove post-weld temper on the corrosion resistance of austenitic stainless steel...
Rok 2003
-
Budowa połączeń zgrzanych wybuchowo jako kryterium doboru parametrów zgrzewania.
PublikacjaPrzedstawiono budowę połączeń zgrzewanych wybuchowo na tle okna zgrzewalności oraz wyniki badań metalograficznych próbek zgrzanych przy różnych parametrach. Podano zakres optymalnych parametrów zgrzewania.
-
Cavitation erosion of heterogeneous thin coatings produced by means of laser cladding
PublikacjaPrzedstawiono badania odporności kawitacyjnej cienkich heterogenicznych warstw nakładanych metodami laserowymi na stal 45. Wykazano dobrą przyczepność i wysoką odporność kawitacyjną wykonanych powłok.
-
Cavitation erosion of some alloys manufactured on steel and iron surfaces by laser beam.
PublikacjaPrzedstawiono badania odporności kawitacyjnej stali węglowej 45 odpornej na korozję 2H13 i technicznego żelaza po ich obróbce laserowej. Warstwę wierzchnią wybranych stali wzbogacono w różne pierwiastki stopowe i badano odporność kawitacyjną na stanowisku z wirującą tarczą. Stwierdzono niską odporność kawitacyjną dla warstw o obniżonej zdolności do utwardzania pod wpływem obciążeń kawitacyjnych oraz silną zależność odporności...
-
Cavitation resistance of OH18N9 steel alloyed with vaidus amount of TiC or Mn by means of laser beam. XIV International Symposium on Gas Flow, Chemical Lasers and High Power Lasers.
PublikacjaPrzedstawiono badania odporności kawitacyjnej stali OH18N9T po laserowym stopowaniu jej powierzchni węglikiem TiC oraz manganem. Wykazano, że wzbogacenie obrabianej stali manganem powoduje przemiany fazowe pod wpływem działania obciążeń kawitacyjnych, co przyczynia się do wzrostu odporności kawitacyjnej. Wzmacnianie stali węglikiem TiC powoduje natomiast zanik zdolności stali do wzmacniania odkształceniowego.
-
Charakterystyka przełomów eksploatacyjnych spiekanych pierścieni synchronizatora
PublikacjaSpiekane pierścienie synchronizatora skrzyni biegów wykonane ze stali niklowo-miedziowej P3054 przedwcześnie zniszczone w warunkach eksploatacji, badano pod kątem roli mikrostruktury na powstawanie przełomów. Stwierdzono, że najprawdopodobniej zróżnicowane warunki procesu technologicznego pierścieni, jak temperatura spiekania, wielkość cząstek proszków, są przyczyną różnic właściwości.
-
Corrosion characteristics of the AL-Si alloy after laser treatment at cryogenic conditions
PublikacjaOmówiono wpływ laserowego powierzchniowego przetapiania stopu Al-Si w warunkach kriogenicznych na jego mikrostrukturę i właściwości użytkowe. W wyniku badań korozyjnych stwierdzono zwiększenie odporności na korozję stopu Al-Siw 0,01 M roztworze H2SO4.
-
Degradacja stali 9CR-1Mo pod wpływem podwyższonej temperatury. Degradation of 9Cr-1Mo steel under the influence of elevated temperature
PublikacjaBadano charakterystyczne cechy degradacji mikrostruktury i właściwości mechanicznych stali 9Cr-1Mo gat. P9 ASTM SA-335 po eksploatacji w piecu rafineryjnym w temperaturze 390-500 stopni C. Wykazano, że po 30 000 godzin wydłużenie obniżyło się o około 30%. Przyczyną spadku wydłużenia były zmiany mikrostruktury związane z umocnieniem osnowy metalicznej przez chrom oraz wynikające z kruchości odpuszczania stali. Większy spadek wydłużenia...
-
Degradacja stali w środowiskach pieców rafineryjnych
PublikacjaW monografii przedstawiono mechanizmy degradacji stali o osnowie ferrytycznej, przeznaczonych do pracy w podwyższonej temperaturze w środowiskach pieców rafineryjnych, na podstawie badań rur po wieloletniej eksploatacji w piecach Rafinerii Gdańskiej SA. Badano stal węglową (gat. K18 PN-75/H-84024) i stale chromowo-molibdenowe typu 5Cr-0,5Mo i 9Cr-1Mo (gat. P5 i P9 ASTM SA-335) po eksploatacji w ciekłych frakcjach węglowodorowych...
-
Effect of laser treatment on the wear and corrosion resistance of aluminiumalloy used for pistons
PublikacjaPrzedstawiono wpływ powierzchniowego laserowego przetapiania w warunkach kriogenicznych na skład chemiczny, mikrostrukturę, mikrotwardość oraz zużycie ścierne i odporność korozyjną stopu AlSi13Mg1CuNi stosowanego na tłoki silników spalinowych. Uzyskano zwiększenie odporności na ścieranie i korozję stopu AlSi13Mg1CuNi.
Rok 2002
-
Cavitation erosion of chromium-manganese and chromium-cobalt coatings processed by laser beam
PublikacjaPrzedstawiono wyniki badań erozji kawitacyjnej napoin wykonanych za pomocą elektrod chromowo-manganowych i chromowo-niklowych oraz obrobionych wiązką lasera CO2 o mocy 1000 W. Próbki poddawano obciążeniom kawitacyjnym na stanowisku z wirującą tarczą. Zaobserwowano wzrost odporności kawitacyjnej napoin, w których dokonano przetopienia ich powierzchni promieniowaniem lasera.
-
Charakterystyka zgorzelin na elementach wyposażenia wewnętrznego ze stali 18Cr-10Ni-0,5Nb w reaktorze instalacji hydrokrakingu
PublikacjaBadano zgorzeliny siarczkowe na kołpakach z austenitycznej stali 18Cr-10Ni-0,5Nb z wnętrza reaktora instalacji hydrokrakingu. Wsad reaktora stanowiły ciekłe węglowodory i wodór o temperaturze 370 stopni C. Stężenie siarkowodoru w aparacie zawierało się w granicach 12 ppm - 1,2% obj. Posługując się elektronowym skaningowym mikroskopem sprzężonym ze spektrometrem rentgenowskim dyspersji energii określono mikrostrukturę i skład chemiczny...
-
Dependence of cavitation performance of superficial iron alloys on the sub-strate
PublikacjaWykazano zależność odporności kawitacyjnej laserowo wytworzonych i elektrodąotuloną napawanych powłok od rodzaju podłoża. Napoiny wykonywano na stali 45, 2H13, 0H18N9 i na żelazie Armco.
-
Efektywność topienia elektrod w podstawowych procesach spawania
PublikacjaW referacie przedstawiono wyniki badań współczynnika stapiania i efektywności stapiania elektrod w procesie spawania ręcznego elektrodami otulonymi (111), półautomatycznego w osłonie różnych gazów - drutami pełnymi i proszkowymi (135,136) oraz metodą spawania automatycznego łukiem krytym (121).
Rok 2015
-
CLAY MINERALS – MINERALOGY AND PHENOMENON OF CLAY SWELLING IN OIL & GAS INDUSTRY
PublikacjaAmong the minerals found in the earth's crust, clay minerals are of the widest interest. Due to the specific properties such as plasticity, absorbing and catalytic properties clay minerals are used in many industries (oil & gas, chemistry, pharmacy, refractory technology, ceramics etc.). In drilling, a phenomenon of swelling clays is frequently observed. It has an important impact on the cementing quality. During the last few decades...
-
Cold Cracking Of Underwater Wet Welded S355G10+N High Strength Steel
PublikacjaWater as the welding environment determines some essential problems influencing steel weldability. Underwater welding of high strength steel joints causes increase susceptibility to cold cracking, which is an effect of much faster heat transfer from the weld area and presence of diffusible hydrogen causing increased metal fragility. The paper evaluates the susceptibility to cold cracking of the high strength S355G10+N steel used,...
-
COMPARISON OF THE ABRASION RESISTANCE OF THE SELECTED BIOMATERIALS FOR FRICTION COMPONENTS IN ORTHOPEDIC ENDOPROSTHESES
PublikacjaRosnące z każdym rokiem zapotrzebowanie na endoprotezy stawów ortopedycznych przy jednoczesnym dążeniu do zwiększenia ich trwałości i wyeliminowania negatywnych skutków ubocznych produktów zużycia, które mogą wywoływać proces zapalny w tkankach determinuje potrzebę poszukiwania nowych biomateriałów, bądź metody modyfikacji ich powierzchni. Nadrzędnym celem prowadzonych przez nas badań było oszacowanie intensywności zużycia ściernego...
-
Development of Education Tomorrow’s Engineers at the Faculty of Mechanical Engineering in GUT
PublikacjaPaper presents educational activity of Faculty of Mechanical Engineering of the Gdańsk University of Technology. Faculty of Mechanical Engineering is one of the largest departments of the Gdańsk University of Technology (GUT), currently educating about 3 000 student. The Faculty of Mechanical Engineering offers studies in different areas: Mechanical Engineering, Medical and Mechanical Engineering, Materials Engineering, Mechatronic,...
-
Effect of Some Sulphur Additives on The Degradation of 9Cr-1Mo Steel After Its 10 Years Service in The CCR Platforming Unit
PublikacjaThe work shows the results of the tests of 9Cr-1Mo steel, which was for 10 years operated in the CCR platforming unit in Group Lotos SA in Gdańsk, and then in the laboratory was sulphidised during 166 h at a temperature of 600 °C. Sulphidation was performed in a mixture of H2-H2S gases at the vapour pressure of sulphur 4.1·10-14 atm, so the order of magnitude of vapour pressure was less than that of the dissociation pressure of...
Rok 2021
-
Effect of annealing temperature on slurry erosion resistance of ferritic X10CrAlSi18 steel
PublikacjaIn the present work, the slurry erosion tests were carried out to investigate the influence of heat treatment on slurry erosion process of ferritic X10CrAlSi18 stainless steel using a slurry pot test rig. X10CrAlSi18 stainless steel was tested in as-received condition and after annealing at three different temperatures: 600°C, 800°C and 1000°C. Degradation of materials due to slurry erosion depends on many factors connected with...