Filters
total: 825
filtered: 707
Search results for: PULSED LASER EVAPORATION
-
Yields and Time-of-Flight Spectra of Neutral High-Rydberg Fragments at the K Edges of the CO2 Molecule
PublicationWe have studied the production of neutral fragments in high-Rydberg (HR) states at the C 1s and O 1s edges of the CO2 molecule by performing two kinds of experiments. First, the yields of neutral HR fragments were measured indirectly by ionizing such fragments in a static electric field and by collecting resulting singly charged positive ions as a function of the photon energy. Such measurements reveal not only excitations below...
-
Ceramic composites for single-layer fuel cells
PublicationComposite materials consisting of acceptor doped lanthanum orthoniobate electrolyte phase (La0.98Ca0.02NbO4) and Li2O:NiO:ZnO semiconducting phase were synthesized. The precursor powder of La0.98Ca0.02NbO4 was prepared in nanocrystalline (mechanosynthesis) and microcrystalline (solid-state synthesis) form. The composite can be applied in a single-layer fuel cell, because of the presence of two phases acting as an anode and a cathode...
-
Determination of dryout localization using a five-equation model of annular flow for boiling in minichannels
PublicationDetailed studies have suggested that the critical heat flux in the form of dryout in minichannels occurs when the combined effects of entrainment, deposition, and evaporation of the film make the film flow rate go gradually and smoothly to zero. Most approaches so far used the mass balance equation for the liquid film with appropriate formulations for the rate of deposition and entrainment respectively. It must be acknowledged...
-
Feasibility study of a Raman spectroscopic route to drug detection
PublicationWe present an surface-enhanced Raman spectroscopy (SERS) approach for detection of drugs of abuse in whole human blood. We utilize a near infrared laser with 830 nm excitation wavelength in order to reduce the influence of fluorescence on the spectra of blood. However, regular plasmon resonance peak of plasmonic nanoparticles, such as silver or gold fall in a much lower wavelength regime about 400 nm. Therefore, we have shifted...
-
ASSESSMENT OF CLIFF STABILITY AFTER THE DEMOLITION OF THE ENGINEERING FACILITIES
PublicationAs a part of an experiment, cliff in Gdynia Redlowo (southern coast of Baltic Sea, Gdansk Bay) was measured using terrestrial laser scanner. The main reason for taking up the subject of the Orlowo Cliff’s stability was a decision about controlled removal one of the war fortification elements. The main purpose of that analysis was to specify suitability of laser scanning in determination of slope’s stability after a violent event....
-
The Optimum Dataset method – examples of the application
PublicationData reduction is a procedure to decrease the dataset in order to make their analysis more effective and easier. Reduction of the dataset is an issue that requires proper planning, so after reduction it meets all the user’s expectations. Evidently, it is better if the result is an optimal solution in terms of adopted criteria. Within reduction methods, which provide the optimal solution there is the Optimum Dataset method (OptD)...
-
The use of liquid crystal thermography TLC and particle image velocimetry PIV in selected technical applications
PublicationNowadays, the energy cost is very high and this problem is carried out to seek techniques for improvement of the aerothermal and thermal (heat flow) systems performances in different technical applications. The transient and steady-state techniques with liquid crystals for the surface temperature and heat transfer coefficient or Nusselt number distribution measurements have been developed. The flow pattern produced by transverse...
-
Theory of recognition in a historical perspective. Axel Honneth's Anerkennung: Eine europäische Ideengeschichte
PublicationThe article discusses Honneth excursion into the realm of the history of ideas. This time Honneth decides to laser it on the notion of "recognition" in three different cultural areas and three different traditions: French, English, and German. The article discusses Honneth's persepctive and attempts at finding the common thread that would link three aforementioned traditions.
-
State-of-the-art framework for high-speed camera and photogrammetric use in geometry evaluation of prestressed concrete failure process
PublicationPrestressed structures are a key to the realization of the boldest architectural ideas, regardless of shape complexity, great height and large span. A characteristic feature of the prestressed structure is the better use of concrete material properties by insertion of internal forces. The internal forces are opposed to external loads effects (forces and deformations of structure). Prestressed reinforced concrete beams are characterized...
-
Influence of Gd deposition on the oxidation behavior and electrical properties of a layered system consisting of Crofer 22 APU and MnCo2O4 spinel
PublicationIn the study, the surface of the Crofer 22APU ferritic steel was modified with gadolinium oxide nanoparticles and a protective-conducting layer consisting of the MnCo2O4 spinel. This system was studied in the context of application in IT-SOFC interconnects. Four types of samples were studied: unmodified steel, steel coated with a manganese-cobalt spinel layer, steel modified with gadolinium oxide nanoparticles, and a system consisting...
-
EXAMINATION OF SOL-GEL DERIVED HYDROXYAPATITE ENHANCED WITH SILVER NANOPARTICLES USING OCT AND RAMAN SPECTROSCOPY
PublicationHydroxyapatite (HAp) has been attracting widespread interest in medical applications. In a form of coating, it enables to create a durable bond between an implant and surrounding bone tissues. With addition of silver nanoparticles HAp should also provide antibacterial activity. The aim of this research was to evaluate the composition of hydroxyapatite with silver nanoparticles in a non-destructive and non-contact way. For control measurements...
-
Novel Cold Crucible Ultrasonic Atomization Powder Production Method for 3D Printing
Publication: A new powder production method has been developed to speed up the search for novel alloys for additive manufacturing. The technique involves an ultrasonically agitated cold crucible installed at the top of a 20 kHz ultrasonic sonotrode. The material is melted with an electric arc and undergoes pulverization with standing wave vibrations. Several different alloys in various forms, including noble and metallic glass alloys, were...
-
Prediction of coking dynamics for wet coal charge
PublicationA one-dimensional transient mathematical model describing thermal and flow phenomena during coal coking in an oven chamber was studied in the paper. It also accounts for heat conduction in the ceramic oven wall when assuming a constant temperature at the heating channel side. The model was solved numerically using partly implicit methods for gas flow and heat transfer problems. The histories of temperature, gas evolution and internal...
-
MULTI-OBJECTIVE OPTIMIZATION PROBLEM IN THE OptD-MULTI METHOD
PublicationNew measurement technologies, e.g. Light Detection And Ranging (LiDAR), generate very large datasets. In many cases, it is reasonable to reduce the number of measuring points, but in such a way that the datasets after reduction satisfy specific optimization criteria. For this purpose the Optimum Dataset (OptD) method proposed in [1] and [2] can be applied. The OptD method with the use of several optimization criteria is called...
-
Mn-Co spinel coatings on Crofer 22 APU by electrophoretic deposition: Up scaling, performance in SOFC stack at 850 °C and compositional modifications
PublicationCeramic coatings for metallic interconnects play a key role in limiting corrosion and chromium evaporation in solid oxide cells. This study presents the upscaling of the electrophoretic deposition (EPD) technique to process Mn-Co spinels on real-dimension Crofer 22 APU interconnects and the test in a SOFC stack. Area specific resistance of long-term test conducted for 5000 h at 850 °C demonstrated that two-steps sintering has a...
-
Comment on "Measurements without probabilities in the final state proposal"
PublicationThe final state proposal [G.T. Horowitz and J.M. Maldacena, J. High Energy Phys.2004(2),8 (2004)] is an attempt to relax the apparent tension betweenstring theory and semiclassicalarguments regarding the unitarity of black hole evaporation. The authors of [R. Bousso and D.Stanford, Phys. Rev. D89, 044038 (2014)] analyze thought experiments where an infalling observerfirst verifies the entanglement between early and late Hawking...
-
EFFECT OF NANOFLUID CONCENTRATION ON TWO-PHASE THERMOSYPHON HEAT EXCHANGER PERFORMANCE
PublicationAn approach – relaying on application of nanofluid as a working fluid, to improve performance of the two-phase thermosyphon heat exchanger (TPTHEx) has been proposed. The prototype heat exchanger consists of two horizontal cylindrical vessels connected by two risers and a downcomer. Tube bundles placed in the lower and upper cylinders work as an evaporator and a condenser, respectively. Distilled water and nanofluid water-Al2O3...
-
Surface Structure of Components Created by Stereolitography
PublicationStereolithography is an additive rapid prototyping method. This method is based on the principle of solidifying a liquid photopolymer (resin) by laser radiation. Models obtained with this method are characterized by a specific surface structure called “stairstep effect”. It causes that, the surface should be processed by additional finishing (postprocessing). To minimize the additional machining process, the model should be set...
-
A simplified energy dissipation based model of heat transfer for subcooled flow boiling
PublicationIn the paper a model is presented based on energetic considerations for subcooled flow boiling heat transfer. The model is the extension of authors own model developed earlier for saturated flow boiling and condensation. In the former version of the model we used the heat transfer coefficient for the liquid single-phase as a reference level, due to the lack of the appropriate model for heat transfer coefficient for the subcooled...
-
Experimental validation of pressure drop models during flow boiling of R134a – effect of flow acceleration and entrainment
PublicationA crucial step to assure proficient work of power and process apparatus is their proper design. A wide array of those devices operates within boiling or condensation of the working fluid to benefit from high heat transfer rates. Two-phase flows are associated with high heat transfer coefficients because of the latent heat of evaporation and high turbulence level between the liquid and the solid surface. Predicting heat transfer...
-
Experimental review of the performances of protective coatings for interconnects in solid oxide fuel cells
PublicationFerritic stainless steel interconnects are used in solid oxide fuel cells; however, coatings are required to improve their performance. Although several types of coatings have been proposed, they have been scarcely investigated under similar conditions. This study compares the characteristics of uncoated Crofer 22 APU and eight different coatings on Crofer 22 APU for up to 3000 h at 800 ◦C. The coatings were deposited at various...
-
3D MODELLING OF CYLINDRICAL-SHAPED OBJECTS FROM LIDAR DATA - AN ASSESSMENT BASED ON THEORETICAL MODELLING AND EXPERIMENTAL DATA
PublicationDespite the increasing availability of measured laser scanning data and their widespread use, there is still the problem of rapid and correct numerical interpretation of results. This is due to the large number of observations that carry similar information. Therefore, it is necessary to extract from the results only the essential features of the modelled objects. Usually, it is based on a process using filtration, followed by...
-
EVALUATION OF 3D MODEL OF REBAR FOR QUANTITATIVE PARAMETERS
PublicationThe construction industry practices and processes are evolving constantly, and with the emergence of Industry 4.0, the use of technologies is expanding. Construction progress monitoring is an essential project lifecycle process; project success and timely completion are linked with effective progress monitoring operations and adopted tools. In the domain of automated construction progress monitoring, 3D modeling techniques have...
-
Gas bubble dynamics - experiment and fractal analysis.
PublicationPrzedstawiono nieliniowe aspekty generowania pęcherzyków gazowych z dysz szklanych umieszczonych pod powierzchnią cieczy. W badaniach eksperymentalnych zastosowano układ laser diodowy- fotodetektor oraz hydrofon. Sygnały z fotodetektora i hydrofonu były wzmacniane, rejestrowane za pomocą karty dźwiękowej, a następnie poddane analzie fraktalnej. W wyniku obliczeń ustalono mapy występowania chaosu w funkcji strumienia objętości gazu.
-
Soft X-ray Induced Production of Neutral Fragments in High-Rydberg States at the O 1s Ionization Threshold of the Water Molecule
PublicationDissociation of water molecules after soft X-ray absorption can yield neutral fragments in high-Rydberg (HR) states. We have studied the production of such fragments by field ionization and ion time-of-flight (TOF) spectrometry. Neutral HR fragments are created at all resonances below the O 1s ionization potential (IP) and particularly within 1 eV above the O 1s IP. The latter effect is due to the recapture of the O 1s photoelectrons...
-
Modeling of active fiber Bragg grating underwater acoustic sensor.
PublicationW pracy przedstawiono wyniki modelowania nowego typu przetwornika hydroakustycznego wykorzystującego światłowodową siatkę Bragga. Siatka ta, domieszkowana jonami pierwiastków ziem rzadkich, pracuje jako laser z rozłożonym sprzężeniem zwrotnym, co pozwala na znaczne zwiększenie czułości tego prztwornika w porównaniu z rozwiązaniami wykorzystującymi siatki pasywne. W celu uzyskania równomiernego rozkładu naprężeń siatki zastosowano...
-
Prototypowe urządzenie laserowe do femtosekundowej mikroobróbki materiałów
PublicationW artykule przedstawiono prototypowe urządzenie do laserowej mikroobróbki materiałów. Urządzenie to wykorzystuje femtosekundowy laser światłowodowy oparty na krysztale Yb:KYW. Wykorzystanie ultrakrótkich impulsów laserowych w mikroobróbce materiałów oferuje dużą przewagę nad mikroobróbką długoimpulsową ze względu na zminimalizowanie szkodliwego wpływu oddziaływań cieplnych. Pozwala to na bardzo precyzyjne i czyste cięcia oraz wysoki...
-
numerical prediction of vortex generated by hydrofoil
PublicationW pracy przedstawiono wyniki obliczeń programami Fluent i Comet dla płata śruby napędowej. Pola prędkości oraz wirowość za płatem porównano z wynikami pomiarów (LDA- Laser Doppler Anemometry) w tunelu kawitacyjnym Centrum Techik Okrętowych (CTO). Przedstawiono wpływ adaptacji siatki wg różnych kryteriów (lokalnej wirowości lub prędkości) na zgodność wyników obliczeń z danymi eksperymentalnymi.
-
Preparation and characterization of TiO2 nanostructures for catalytic CO2 photoconversion
PublicationThe titanium dioxide target (99.7%) of 1 cm in dia was ablated in vacuum by laser pulses(6 ns) at 266 nm and at repetition rate of 10 Hz. During deposition the laser fluence between 1 and 3.5 J/cm2 and the O2 pressure from the range of 10-2 - 1 Pa were applied. The thin TiO2 films were deposited on glass substrate (1 × 1 cm2) heated up to 500 °C. The chemical composition of the film and samples produced by annealing were investigated...
-
Fracture Energy of Bonded Joints with 2D Elastic Adhesive Layer
PublicationWhen bonded joint is subjected to mode I fracture loading, the adhesive joints analytical solutions treats the adhesive layer, usually, as not existing or 1D Hooke elastic layer. In the case of 1D elastic layer, represented as Hookes spring element, is acting, only, in direction contrary to the applied load. Basing on the information yielded from sensitive laser profilometry technique, where deflections of bonded part of the joint...
-
Low-Level Aerial Photogrammetry as a Source of Supplementary Data for ALS Measurements
PublicationThe development of laser scanning technology ALS allows to make high-resolution measurements for large areas result-ing in significant reduction of costs. The main stakeholders at heights data received from the airborne laser scanning is mainly state administration. The state institutions appear among projects such as ISOK. Each point is classified in ac-cordance with the standard LAS 1.2, our research focuses on the class 6 -...
-
Coherent-wave Monte Carlo method for simulating light propagation in tissue
PublicationSimulating propagation and scattering of coherent light in turbid media, such as biological tissues, is a complex problem. Numerical methods for solving Helmholtz or wave equation (e.g. finite-difference or finite-element methods) require large amount of computer memory and long computation time. This makes them impractical for simulating laser beam propagation into deep layers of tissue. Other group of methods, based on radiative...
-
Accuracy improvement of the prestressed concrete structures precise geometry assessment by use of bubble micro-sampling algorithm
PublicationPrestressed concrete structures are well-known technology for a vast period, but nevertheless, this very technology is a leading solution, currently used in construction industry. Prestressed concrete structures have a huge advantage over conventional methods because it uses the properties of concrete in a very efficient way. The main idea behind this technology is to introduce into the cross-section of the structure, the internal...
-
Evaluating Gelatin-Based Films with Graphene Nanoparticles for Wound Healing Applications
PublicationIn this study, gelatin-based films containing graphene nanoparticles were obtained. Nanoparticles were taken from four chosen commercial graphene nanoplatelets with different surface areas, such as 150 m2/g, 300 m2/g, 500 m2/g, and 750 m2/g, obtained in different conditions. Their morphology was observed using SEM with STEM mode; porosity, Raman spectra and elemental analysis were checked; and biological properties, such as hemolysis...
-
Effect of interconnect coating procedure on solid oxide fuel cell performance
PublicationChromium (Cr) species vaporizing from chromia-forming alloy interconnects is known as a source of degradation in solid oxide fuel cell (SOFC) stacks called “cathode poisoning”. (Mn,Co)3O4 spinel coatings offer good protection against Cr evaporation during operation. In this study, Crofer 22 APU steel interconnects were electrophoretically deposited in different mediums to obtain high packing of green coating layer. The optimized...
-
In-situ Cu-doped MnCo-spinel coatings for solid oxide cell interconnects processed by electrophoretic deposition
PublicationThe Cu doping of the Mn–Co spinel is obtained “in-situ” by electrophoretic co-deposition of CuO and Mn1.5Co1.5O4 powders and subsequent two-step reactive sintering. Cu-doped Mn1.5Co1.5O4 coatings on Crofer22APU processed by electrophoretic co-deposition method are tested in terms of long term oxidation resistance and area specific resistance tests up to 3600 h. The introduction of Cu in the spinel lead to higher level of densification...
-
Utilisation of waste heat from the power plant by use of the ORC aided with bleed steam and extra source of heat
PublicationUtilization of waste heat recovered from the exhaust gases of the power generation unit by means of ORC (organic Rankine cycles) installation is considered. The waste heat is available in the form of a stream of hot water having temperature of 90 stC in the amount of 200 MWt. To increase evaporation temperaturę of ORC working fluid the heat of steam from the extraction points from the low-pressure part of steam turbine is used....
-
The influence of the fuel spray nozzle geometry on the exhaust gas composition from the marine 4-stroke diesel engine
PublicationThe paper presents experimental research on a 4-stroke, 3-cylinder, turbocharged AL25/30 Diesel engine. Research consisted in investigating the effect of the geometry of the fuel injectors on the exhaust gas composition from the engine. During measurements, the engine was operated with a regulator characteristic of a load range from 40 kW to 280 kW, made by electric water resistance. The engine was mechanically coupled to the electric...
-
Investigation and operation problems of metal tanks in Poland
PublicationThe paper consists of three parts concerned with steel cylindrical, vertical tank for liquid fuel. In the first part the present trends in tank design and building in Poland are described. The main are: · reduction of environment contamination danger caused by tank leakage and hydrocarbons evaporation, · increasing capacity of new tanks (100000 m3 and more) due to economic factor - reduction of steel amount per m3 of storage capacity....
-
Failure analysis of the exhaust valve face in diesel marine engine
PublicationThe exhaust valve from marine diesel engine which was damaged after 2000 hours of service was investigated. In order to prolong the service time the valve face was cladded with cobalt base alloy using laser technique. After failure microstructural and chemical analyses reviled that cladding process was conducted improperly. The chemical composition of the clad layer was far from the designed one and what more completely inhomogeneous....
-
The circle object detection with the use of Msplit estimation
PublicationThe paper presents the use of Msplit(q) - estimation in the filtration and aggregation of point clouds containing a known number of elliptical shapes with preliminary unknown - locations and dimensions. These theoretical solutions may have practical relevance especially in the modelling of terrestrial laser scanning data of objects that have similar shape to circles. Mentioned shapes can be scanned of tree trunks, columns, gutters,...
-
From a Point Cloud to a 3D Model - an Exercise for Users of AutoCAD and Revit
PublicationThe paper presents a proposal of the topic of an exercise for students of building faculties as part of classes on 3D modelling. The task consists in creating a three-dimensional model based on the measurement obtained with the Leica P30 laser scanner. Due to the maximum number of points in the cloud in the presented programs, the output files must be properly cleared and reduced. The point cloud was pre-processed in Cyclone software....
-
3D modelling of liquid fuels base infrastructure for the purpose of visualization and geometrical analysis
PublicationThe paper presents the methodology for obtaining a 3D model of the tank for liquid fuels on the basis of the terrestrial laser scanning and its processing for the analysis of tanks geometry. The development process indicates the possibility to obtain the reliable results useful for the evaluation of the tank side surfaces geometry (shells). The result of the development is a 3D model of the tank, taking into account the individual...
-
MACHINE VISION DETECTION OF THE CIRCULAR SAW VIBRATIONS
PublicationDynamical properties of rotating circular saw blades are crucial for both production quality and personnel safety. This paper presents a novel method for monitoring circular saw vibrations and deviations. A machine vision system uses a camera and a laser line projected on the saw’s surface to estimate vibration range. Changes of the dynamic behaviour of the saw were measured as a function of the rotational speed. The critical rotational...
-
Load test of new European record holder in span length among extradosed type bridges
PublicationThe article presents acceptance load tests of a newly built extradosed MS-3 bridge located along the national road DK-16 near Ostróda (Poland). The structure features significant dimension in European reference scale. It is a new record holder in span length regarding this distinct bridge category. Its length ranges 206 m. Static and dynamic load tests were performed here. The program was extended by entire structural laser scanning...
-
Employing economical methods for pavement defects estimation
PublicationIt is a common practise that measurements of road surface conditions are made using professional and expensive apparatus. Typically a van or a truck equipped with a set of professional sensors i.e. laser scanners of surface is used, therefore the measurement update period is often quite long. Two alternative low-cost methods for estimating road pavement defects and failures were proposed and investigated by the authors. The first...
-
Vibrational Quenching of Optically Pumped Carbon Dimer Anions
PublicationCareful control of quantum states is a gateway to research in many areas of science such as quantum information, quantum-controlled chemistry, and astrophysical processes. Precise optical control of molecular ions remains a challenge due to the scarcity of suitable level schemes, and direct laser cooling has not yet been achieved for either positive or negative molecular ions. Using a cryogenic wire trap, we show how the internal...
-
Utilization of oriented crystal growth for screening of aromatic carboxylic acids cocrystallization with urea
PublicationThe possibility of molecular complex formation in the solid state of urea with benzoic acid analogues was measured directly on the crystallite films deposited on the glass surface using powder X-ray diffractometry (PXRD). Obtained solid mixtures were also analyzed using Fourier transform infrared spectroscopy (FTIR). The simple droplet evaporation method was found to be efficient, robust, fast and cost-preserving approach for first...
-
Effect of the North Atlantic Thermohaline Circulation on changes in climatic conditions and river flow in Poland
Publication: The purpose of this study is to find connections between the North Atlantic Thermohaline Circulation (NA THC), climate elements, such as cloud cover, precipitation, air temperature, sunshine duration, and relative humidity, and flow of rivers in Poland. The intensity of NA THC was characterized by the DG3L index, which was established to assess changes in the amount of heat transported by NA THC along with the transport of water...
-
Fibre Bragg Grating pressure transducer using a profiled membrane.
PublicationW pracy przedstawiono nowatorską konstrukcję podwodnego światłowodowego przetwornika ciśnienia, w którym elementem czujnikowym jest światłowodowa siatka Bragga. W omawianym przetworniku siatka Bragga jest zapisana w światłowodzie domieszkowanym pierwiastkami ziem rzadkich i pracuje jako pompowany optycznie laser z rozłożonym sprzężeniem zwrotnym. Dzięki zastosowaniu profilowanej membrany uzyskuje się jednorodny rozkład naprężeń...